4
ROLAND JX-10 EPROM A – REPLACEMENT SOUND BOARD EPROM HI – LO Optional In this brief guide will be explained how to upgrade Roland JX-10 replacing the EPROM placed on the Assigner board. To accomplish this elementary operation you’ll need: A: Phillips screwdriver B: IC Extractor C: IC Integrated Circuit Leg Straightener Tool D: EPROM A ver. 3.0 The optional EPROM High and Low can be placed, respectively, on Upper and Lower Sound Board. For further information about EPROM High and Low, please write to: [email protected] To open the JX-10, please look at the following scheme: Panel removal screws are * E and * C Unscrew * C first, then * E (left or right is not influential). At this point the upper panel can be raised up. Be careful to lift up gently the cover and stop when a resistance is detected. This means that the cover is open at its full. ROLAND JX-10 EPROM A – REPLACEMENT I

ROLAND JX-10 EPROM A – REPLACEMENT - vecoven.com€¦ · ROLAND JX-10 EPROM A – REPLACEMENT SOUND BOARD EPROM HI – LO Optional. In this brief guide will be explained how …

  • Upload
    buibao

  • View
    245

  • Download
    0

Embed Size (px)

Citation preview

Page 1: ROLAND JX-10 EPROM A – REPLACEMENT - vecoven.com€¦ · ROLAND JX-10 EPROM A – REPLACEMENT SOUND BOARD EPROM HI – LO Optional. In this brief guide will be explained how …

ROLAND JX-10 EPROM A – REPLACEMENT SOUND BOARD EPROM HI – LO Optional In this brief guide will be explained how to upgrade Roland JX-10 replacing the EPROM placed on the Assigner board. To accomplish this elementary operation you’ll need: A: Phillips screwdriver B: IC Extractor C: IC Integrated Circuit Leg

Straightener Tool D: EPROM A ver. 3.0 The optional EPROM High and Low can be placed, respectively, on Upper and Lower Sound Board. For further information about EPROM High and Low, please write to: [email protected]

To open the JX-10, please look at the following scheme:

Panel removal screws are * E and * C Unscrew * C first, then * E (left or right is not influential). At this point the upper panel can be raised up. Be careful to lift up gently the cover and stop when a resistance is detected. This means that the cover is open at its full.

R O L A N D J X - 1 0 E P R O M A – R E P L A C E M E N T I

Page 2: ROLAND JX-10 EPROM A – REPLACEMENT - vecoven.com€¦ · ROLAND JX-10 EPROM A – REPLACEMENT SOUND BOARD EPROM HI – LO Optional. In this brief guide will be explained how …

Once opened JX-10, please look at the following scheme:

EPROM A replacement will take place on I = ASSIGNER BOARD (circled in red). Optional EPROM High and Low replacement will, in case, take place on K = LOWER SOUND BOARD and L = UPPER SOUND BOARD with similar operation.

R O L A N D J X - 1 0 E P R O M A – R E P L A C E M E N T

II

Page 3: ROLAND JX-10 EPROM A – REPLACEMENT - vecoven.com€¦ · ROLAND JX-10 EPROM A – REPLACEMENT SOUND BOARD EPROM HI – LO Optional. In this brief guide will be explained how …

Be careful to lift gently the white flat cable that hides EPROM A

Remove EPROM A as much kindly as before with “B” IC Extractor – the picture shows a recent Beta version. If needed, use tool C “IC Integrated Circuit Leg Straightener Tool” to straighten possibily bent pins or to adapt pins to the base.

R O L A N D J X - 1 0 E P R O M A – R E P L A C E M E N T

III

Page 4: ROLAND JX-10 EPROM A – REPLACEMENT - vecoven.com€¦ · ROLAND JX-10 EPROM A – REPLACEMENT SOUND BOARD EPROM HI – LO Optional. In this brief guide will be explained how …

• Place the new EPROM A ver. 3.0 – respecting the same placing direction • Reconnect gently the white flat cable again • Close JX-10 upper panel, fasten * C and * E screws then reconnect power cable and turn on JX-10 • If EPROM A was correctly installed, the JX-10 display will show:

This guide © 2014 [email protected] All rights reserved. Duplication in any manner is strictly prohibited.

R O L A N D J X - 1 0 E P R O M A – R E P L A C E M E N T

IV