SA-WMSP75/WMSP85 - Philips Parts and Accessories Corporation Home Audio Company ... STK404-130S 1SS133T-72 1SS133T-72 100 10V 120 ... SA-WMSP75/WMSP85

SA-WMSP75/WMSP85US Model

Canadian ModelSA-WMSP75/WMSP85

AEP ModelUK Model

E ModelAustralian Model

SA-WMSP85

SERVICE MANUAL

ACTIVE SUBWOOFER

Ver 1.4 2004.01

SPECIFICATION

Sony CorporationHome Audio Company

Published by Sony Engineering Corporation

9-877-044-052004A16-1

© 2004.01

• SA-WMSP75/WMSP85 are the sub woofersection HT-DDW750,HT-1800DP,HT-6600DPand HT-1750DP. photo: SA-WMSP75

• AbbreviationAU : Australian modelCA : Canadian modelCEK : UK modelCEL : AEP modelMX : Mexican modelSP : Singapore modelU : US model

POWER OUTPUT AND TOTALHARMONIC DISTORTION:

With 6 ohm loads, from 28 – 200 Hz; rated 75watts (SA-WMSP75) / 100 watts (SA-WMSP85),minimum RMS power, with no more than 0.8%total harmonic distortion from 250 milliwatts torated output (Models of area code U only).Speaker system Active subwoofer,

magnetically shielded

Speaker unit Woofer: 20 cm cone type

Enclosure type Acoustically loaded bassreflex

Continuous RMS power output(6 ohms, 20 – 250 Hz)SA-WMSP75 75 WSA-WMSP85 100 W

Reproduction frequency range28Hz – 200 Hz

High frequency cut-off frequency150 Hz

Input LINE IN (input pin jacks)

Power requirements

Area code Power requirements

U, CA, MX 120 V AC, 60 Hz

CEL, CEK, SP, AU 230 V AC, 50/60 Hz

E2 120/220/230 V AC, 50/60 Hz

Power consumptionSA-WMSP75 75 WSA-WMSP85 100 W

Dimensions (w/h/d) Approx. 270 × 325 × 398mm (10 3/4 × 12 7/8 × 15 3/4inches) including frontpanel

MassSA-WMSP85 10.0 kg (22 lb 1 oz)SA-WMSP75 9.0 kg (19 lb 14 oz)

2

SA-WMSP75/WMSP85

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITHMARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTSLIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESECOMPONENTS WITH SONY PARTS WHOSE PART NUMBERSAPPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTSPUBLISHED BY SONY.

SAFETY CHECK-OUT After correcting the original service problem, perform thefollowing safety checks before releasing the set to the customer:Check the antenna terminals, metal trim, “metallized” knobs, screws,and all other exposed metal parts for AC leakage. Check leakage asdescribed below.

LEAKAGE

The AC leakage from any exposed metal part to earth ground andfrom all exposed metal parts to any exposed metal part having areturn to chassis, must not exceed 0.5 mA (500 microamperes).Leakage current can be measured by any one of three methods.

1. A commercial leakage tester, such as the Simpson 229 or RCAWT-540A. Follow the manufacturers’ instructions to use theseinstruments.

2. A battery-operated AC milliammeter. The Data Precision 245digital multimeter is suitable for this job.

3. Measuring the voltage drop across a resistor by means of aVOM or battery-operated AC voltmeter. The “limit” indicationis 0.75 V, so analog meters must have an accurate low-voltagescale. The Simpson 250 and Sanwa SH-63Trd are examples ofa passive VOM that is suitable. Nearly all battery operateddigital multimeters that have a 2V AC range are suitable. (SeeFig. A)

ATTENTION AU COMPOSANT AYANT RAPPORTÀ LA SÉCURITÉ!

LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LESDIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONTCRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NEREMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONYDONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OUDANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

Fig. A. Using an AC voltmeter to check AC leakage.

0.15µF

To Exposed MetalParts on Set

1.5kΩACvoltmeter(0.75V)

Earth Ground

Unleaded solderBoards requiring use of unleaded solder are printed with the lead-free mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not come printed withthe lead free mark due to their particular size.)

: LEAD FREE MARKUnleaded solder has the following characteristics.• Unleaded solder melts at a temperature about 40°C higher than

ordinary solder.Ordinary soldering irons can be used but the iron tip has to beapplied to the solder joint for a slightly longer time.Soldering irons using a temperature regulator should be set toabout 350°C.Caution: The printed pattern (copper foil) may peel away if theheated tip is applied for too long, so be careful!

• Strong viscosityUnleaded solder is more viscous (sticky, less prone to flow) thanordinary solder so use caution not to let solder bridges occur suchas on IC pins, etc.

• Usable with ordinary solderIt is best to use only unleaded solder but unleaded solder mayalso be added to ordinary solder.

33

SA-WMSP75/WMSP85

SECTION 1DIAGRAMS

Note on Printed Wiring Boards:• X : parts extracted from the component side.• Y : parts extracted from the conductor side.• b : Pattern from the side which enables seeing.

THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.(In addition to this, the necessary note is printed in each block.)

Note on Schematic Diagram:• All capacitors are in µF unless otherwise noted. p: pF. 50

WV or less are not indicated except for electrolytics andtantalums.

• 2 : nonflammable resistor.• 5 : fusible resistor.• All resistors are in Ω and 1/4

W or less unless otherwise

specified.• C : panel designation.

• A : B+ Line.• B : B– Line.• Voltages are dc with respect to ground under no-signal

conditions.no mark : Power on

• Voltages are taken with a VOM (Input impedance 10MΩ).Voltage variations may be noted due to normal preductiontolerances.

• Signal path.F : AUDIO

• AbbreviationCND : Canadian model.E2 : 120V AC Area in E model.MX : Mexican model.

The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.

Les composants identifiés parune marque 0 sont critiquespour la sécurité.Ne les remplacer que par unepièce portant le numéro spécifié.

1-1. Circuit Board Location

SWITCH BOARD

CONTROL BOARD

POWER TRANS BOARD

INPUT(CONTROL) BOARD

MAIN BOARD

1-2. IC Block Diagrams

IC301 STK404-130S (MAIN Board)

2 31 4 5 6 7 8 9 10 11 12 13SUB

IC301 STK-404-100S (MAIN Board)

1 2 3 4 5 6 7 8 9 10 11 12SUB

44

SA-WMSP75/WMSP85

1-3. Printed Wiring Board – MAIN Section – • See page 3 for Circuit Boards Location. • : Uses unleaded solder.

Ref. No. Location

D205 C-3D206 C-3D301 E-4D302 E-4D304 D-2D401 F-2D402 F-2D403 E-2D501 E-2D502 E-4D602 C-2

IC202 B-3IC203 B-3IC301 D-4

Q501 D-2Q502 D-2Q503 D-2Q504 D-2Q505 E-4

• SemiconductorLocation

IC20

2

IC30

1

IC20

3

INPUT

CN402WMSP75 : 3PWMSP85 : 6P

SP1WMSP85

WMSP75

WM

SP85

WMSP85

WM

SP75

WMSP75

54

1 8

54

1 8

(11)

11

POWER TRANS

( )

1 2

A

B

C

D

E

F

G

3 4 5 6 7 8

Ver 1.2 2003.06

55

SA-WMSP75/WMSP85

1-4. Printed Wiring Board – POWER Section – • See page 3 for Circuit Boards Location. • : Uses unleaded solder.

EXCEPT E2

WMSP85

E2

230V

CNP401WMSP75:3PWMSP85:6P

ACIN

E2

Ver 1.2 2003.06

66

SA-WMSP75/WMSP85

1-5. Schematic Diagrams • See page 3 for IC Block Diagrams.

C402

C401

C409

C410

RY

301

JW402

JW403

JW404

S901R502R503

R504

R505

R312

C2

R311

R307

R306C312

C313

R305

C311

R302

R314

JW401

R310

R301R506

R507

R508

C407

C408

JW501

C301 R303

JW2

JW1

R500R501

T1

R403

R404

J101

R110R202

R20

6

R208

R209

R210

R211

C101

R212 R213

R214 C210

C211R217

R207

R31

5

R313

CN901

C801

C209

C201

C203 C204

IC202(2/2)

R20

5

C205

C206

D20

5

D206

C208

R216

IC202(1/2)

IC203(1/2)

IC203(2/2)

RV801

CNP801CNP111

C207

IC301

WMSP75

WM

SP75

WMSP85

D30

1

D30

2

C303

R309

Q505

C302

D50

2

D602

D30

4

C309

C310

C308

CN301

C307

R401

C306

C305

D401

R304

C304

R402

C405

C406 C404

C403

D501

C501

Q501

Q502

C502

C601

C503

D403

Q504

Q503

D402

CN2

CN1

S2

F902

F901

F901

C2

CN3

D901

R308

CN402 CNP401

R601

CN204

C901

CN101

CN202

CN2

CN1

0.1

0.1

0.1

0.1

47k100k100k

22k

22k

4700p250V

680 1W

4.7k

4.7k220p

220p

47k

10p

47k

11/4W

10

4.7k22k

4.7k

1k

47050V

47050V

220p50V

470

2.2k10k

101/4W

101/4W

100k1k

10k

10k

100k

470k

220k

220p

22k 22k

220k 10 50

220p100k

10k

47k

1050

220p

1050V

0.1 0.1

NJM4565DD

100k

1050V

1050V

MTZ

J-T-

72-1

2B

MTZJ-T-72-12B

0.22

10k

NJM4565DD

NJM4565DD

NJM4565DD

20k

3P3P

0.01

STK404-130S

1SS

133T

-72

1SS

133T

-72

10010V

120(WMSP85)220(WMSP75)

2SC2785TP-E

10 50V

1SS1

33T-

72

1SS133T-72

1SS

133T

-72

0.150V

0.150V

1050V

2P

4750V

1k

1050V

10050V

1002W

10050V

1k 2W

1SS133T-72

1050V

2SC2785TP-E

2SC2784-EFP-TP

22035V

1050V

220 10V

11ES2-NTA2B

DTC124ESA-TP

2SC2785TP-E

11ES2-NTA2B

2P

2P

4700p250V

2P

SEL5423E-TP15

2P

4700p250V

2P

2P

2P

2P

∗1

∗1 ∗3

∗3

∗5

∗6

∗6

∗6

∗2 ∗2

∗4

∗7

∗7 R313 WMSP75 : 10k WMSP85 : 22k

∗4 R313 WMSP75 : 2.2k/2W WMSP85 : 3.3k/3W

∗5 D401 WMSP75 : D3SBA20 WMSP85 : RBV-602-01

∗2 CN402, CNP401 WMSP75 : 3P WMSP85 : 6P

∗1 C405, C406 WMSP75 : 100uF/25V WMSP85 : 100uF/50V

∗3 C403, C404 WMSP75 : 3300uF/50V WMSP85 : 4700uF/63V

WMSP85

∗6

Ver 1.2 2003.06

SECTION 2EXPLODED VIEWS

NOTE:• -XX, -X mean standardized parts, so they may

have some differences from the original one.• Items marked “*” are not stocked since they

are seldom required for routine service. Somedelay should be anticipated when ordering theseitems.

• The mechanical parts with no reference numberin the exploded views are not supplied.

• AbbreviationAUS : Australian modelE2 : 120V AC Area in E modelCND : Canadian modelMX : Mexican modelSP : Singapore model

7

SA-WMSP75/WMSP85

The components identified by mark 0 ordotted line with mark 0 are critical for safety.Replace only with part number specified.

Les composants identifiés par une marque0 sont critiques pour la sécurité.Ne les remplacer que par une pièce portantle numéro spécifié.

2-1. Front Section

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks

1 4-243-842-01 NET, GRILLE (SILVER)1 4-243-842-11 NET, GRILLE (BLACK)2 4-998-417-02 EMBLEM (No.5), SONY3 4-243-834-01 PANEL, FRONT (SILVER)(US,CND)3 4-243-834-11 PANEL, FRONT (BLACK)(WMSP75 : US)

3 4-243-834-21 PANEL, FRONT (SILVER)(EXCEPT US,CND)4 4-973-938-83 KNOB (A), PUSH

6 4-999-482-01 KNOB (VOL)(SILVER)6 4-999-482-11 KNOB (VOL)(BLACK)8 4-235-677-01 SCREW (4X20)(TYPE1), +BVTPSP1 1-529-995-12 SPEAKER (20cm)(WMSP75)SP1 1-825-004-13 SPEAKER (20cm)(WMSP85)

#1 7-685-647-79 SCREW +BVTP 3X10 TYPE2 IT-3

1

2

3

6

4

8

#1

#1

#1

#1

Amp section

SP1

notsupplied

notsupplied

suppliedwith RV801

notsupplied

Ver 1.3 2003.12

8

SA-WMSP75/WMSP85

2-2. Amp Section




51 A-4723-991-A CABINET ASSY, SPEAKER (SILVER) (US,CND,E2,MX,AUS)

51 A-4725-995-A CABINET ASSY, SPEAKER (BLACK)(WMSP75 : US)

51 A-4723-998-A CABINET ASSY, SPEAKER (SILVER)(AEP,UK,SP)52 A-4731-189-A MAIN BOARD,COMPLETE (WMSP75)52 A-4731-195-A MAIN BOARD,COMPLETE (WMSP85)

53 4-235-677-01 SCREW (4X20)(TYPE1), +BVTP* 54 3-703-244-00 BUSHING (2104), CORD057 1-696-847-11 CORD, POWER (AUS)057 1-769-744-11 CORD, POWER (AEP,UK,SP)057 1-783-532-11 CORD, POWER (US,CND,MX)

057 1-792-823-12 CORD, POWER (TRACKING)(E2)

0F901 1-533-450-11 FUSE, GLASS TUBE 2.5A/125V (US,CND,MX)0F901 1-532-463-51 FUSE T1AL/250V (EXCEPT US,CND,MX)0F902 1-532-464-31 FUSE T2.5AL /250V (E2)0T1 1-439-625-11 POWER TRANSFORMER

(WMSP85 : US,CND,MX)0T1 1-439-628-11 POWER TRANSFORMER (WMSP75 : US,CND

0T1 1-439-623-11 POWER TRANSFORMER (E2)0T1 1-439-624-11 POWER TRANSFORMER (AEP,UK,SP,AUS)

#1 7-685-647-79 SCREW +BVTP 3X10 TYPE2 IT-3#2 7-685-650-79 SCREW +BVTP 3X16 TYPE2 IT-3#3 7-685-881-09 SCREW +BVTT 4X8 (S)

52

51

53

53

54

57#1

#2#3

#3

#1

#1

#3

notsupplied

notsupplied

F902

F901

T1

notsupplied

notsupplied

notsupplied

notsupplied

Ver 1.2 2003.06

9

SECTION 3ELECTRICAL PARTS LIST

SA-WMSP75/WMSP85

NOTE:• Due to standardization, replacements in the

parts list may be different from the partsspecified in the diagrams or the componentsused on the set.

• -XX, -X mean standardized parts, so theymay have some difference from the originalone.

• Items marked “*” are not stocked since theyare seldom required for routine service.Some delay should be anticipated whenordering these items.

• CAPACITORS:uF: µF

• COILSuH: µH

• RESISTORSAll resistors are in ohms.METAL: metal-film resistorMETAL OXIDE: Metal Oxide-film resistorF: nonflammable

• SEMICONDUCTORSIn each case, u: µ, for example:uA...: µA... , uPA... , µPA... ,uPB... , µPB... , uPC... , µPC... ,uPD..., µPD...

• AbbreviationAUS : Australian modelE2 : 120V AC Area in E modelCND : Canadian modelMX : Malaysia modelSP : Singapore model

When indicating parts by reference number,please include the board name.

The components identified by mark 0 ordotted line with mark 0 are critical for safety.Replace only with part number specified.

Les composants identifiés par une marque0 sont critiques pour la sécurité.Ne les remplacer que par une pièce portantle numéro spécifié.

CONTROL


CONTROL BOARD**************

< CAPACITOR >

C801 1-126-964-11 ELECT 10uF 20.00% 50V

< CONNECTOR >

CNP801 1-691-765-11 PLUG (MICRO CONNECTOR) 3P

< VARIABLE RESISTOR >

RV801 1-227-511-11 RES, VAR, CARBON 20K (LEVEL)************************************************************

INPUT (CONTROL) BOARD*********************

< CAPACITOR >

C101 1-128-813-11 CERAMIC 220PF 5% 50VC201 1-126-964-11 ELECT 10uF 20.00% 50V

< CONNECTOR >

* CN101 1-506-944-11 PIN, CONNECTOR 2P

< JACK >

J101 1-815-025-11 JACK, PIN 1P (INPUT)

< RESISTOR >

R110 1-249-441-11 CARBON 100K 5% 1/4WR202 1-249-417-11 CARBON 1K 5% 1/4W F

************************************************************

A-4731-189-A MAIN BOARD, COMPLETE (WMSP75)*********************

A-4731-195-A MAIN BOARD, COMPLETE (WMSP85)*********************

< CAPACITOR >

C203 1-136-165-00 FILM 0.1uF 5% 50VC204 1-136-165-00 FILM 0.1uF 5% 50VC205 1-126-964-11 ELECT 10uF 20.00% 50VC206 1-126-964-11 ELECT 10uF 20.00% 50VC207 1-131-679-31 FILM 0.01uF 5% 50V

C208 1-131-696-11 FILM 0.22uF 5% 50VC209 1-128-813-11 CERAMIC 220PF 5% 50VC210 1-126-964-11 ELECT 10uF 20.00% 50VC211 1-128-813-11 CERAMIC 220PF 5% 50VC301 1-128-813-11 CERAMIC 220PF 5% 50V

C302 1-126-964-11 ELECT 10uF 20.00% 50VC303 1-104-665-11 ELECT 100uF 20.00% 10VC304 1-126-968-11 ELECT 100uF 20.00% 50VC305 1-126-968-11 ELECT 100uF 20.00% 50VC306 1-126-964-11 ELECT 10uF 20.00% 50V

C307 1-126-967-11 ELECT 47uF 20.00% 50VC308 1-126-964-11 ELECT 10uF 20.00% 50VC309 1-136-165-00 FILM 0.1uF 5% 50VC310 1-136-165-00 FILM 0.1uF 5% 50VC311 1-162-199-31 CERAMIC 10PF 5% 50V

C312 1-128-813-11 CERAMIC 220PF 5% 50VC313 1-128-813-11 CERAMIC 220PF 5% 50VC401 1-136-165-00 FILM 0.1uF 5% 50VC402 1-136-165-00 FILM 0.1uF 5% 50VC403 1-126-974-11 ELECT 3300uF 20.00% 50V

(WMSP75)

C403 1-104-482-11 ELECT 4700uF 20.00% 63V(WMSP85)

C404 1-126-974-11 ELECT 3300uF 20.00% 50V(WMSP75 )

C404 1-104-482-11 ELECT 4700uF 20.00% 63V(WMSP85)

C405 1-104-665-11 ELECT 100uF 20.00% 25V(WMSP75)

C405 1-126-968-11 ELECT 100uF 20.00% 50V(WMSP85)

C406 1-104-665-11 ELECT 100uF 20.00% 25V(WMSP75)

C406 1-126-968-11 ELECT 100uF 20.00% 50V(WMSP85)

C407 1-126-971-11 ELECT 470uF 20.00% 50V(WMSP85)

C408 1-126-971-11 ELECT 470uF 20.00% 50V(WMSP85)

C409 1-136-165-00 FILM 0.1uF 5% 50V(WMSP85)

C410 1-136-165-00 FILM 0.1uF 5% 50V(WMSP85)

C501 1-126-964-11 ELECT 10uF 20.00% 50VC502 1-126-949-11 ELECT 220uF 20.00% 35V

MAININPUT(CONTROL)

Ver 1.2 2003.06


10

SA-WMSP75/WMSP85



C503 1-126-934-11 ELECT 220uF 20.00% 10VC601 1-126-964-11 ELECT 10uF 20.00% 50V

< CONNECTOR >

* CN202 1-506-944-11 PIN, CONNECTOR 2PCN204 1-564-505-11 PLUG, CONNECTOR 2PCN301 1-564-320-00 PIN, CONNECTOR (3.96mm PITCH) 2PCN402 1-785-101-11 PIN, CONNECTOR (3.96mm PITCH) 3P

(WMSP75)CN402 1-785-104-11 PIN, CONNECTOR (3.96mm PITCH) 6P

(WMSP85)

< CONNECTOR >

CNP111 1-691-765-11 PLUG (MICRO CONNECTOR) 3P

< DIODE >

D205 8-719-110-31 DIODE MTZJ-T-72-12BD206 8-719-110-31 DIODE MTZJ-T-72-12BD301 8-719-911-19 DIODE 1SS133T-72D302 8-719-911-19 DIODE 1SS133T-72D304 8-719-911-19 DIODE 1SS133T-72

D401 8-719-500-56 DIODE D3SBA20 (WMSP75)D401 8-719-302-38 DIODE RBV-602-01 (WMSP85)D402 8-719-024-99 DIODE 11ES2-NTA2B (WMSP85)D403 8-719-024-99 DIODE 11ES2-NTA2B (WMSP85)D501 8-719-911-19 DIODE 1SS133T-72

D502 8-719-911-19 DIODE 1SS133T-72D602 8-719-911-19 DIODE 1SS133T-72

< EARTH TERMINAL >

* G1 1-537-738-21 TERMINAL, EARTH* G2 1-537-738-21 TERMINAL, EARTH

< IC >

IC202 8-759-636-74 IC NJM4565DDIC203 8-759-636-74 IC NJM4565DDIC301 6-600-091-01 IC STK404-130S (WMSP85)IC301 6-600-181-01 IC STK-404-100S (WMSP75)

< TRANSISTOR >

Q501 8-729-119-78 TRANSISTOR 2SC2785TP-EQ502 8-729-178-42 TRANSISTOR 2SC2784-EFP-TPQ503 8-729-119-78 TRANSISTOR 2SC2785TP-EQ504 8-729-029-86 TRANSISTOR DTC124ESA-TPQ505 8-729-119-78 TRANSISTOR 2SC2785TP-E

< RESISTOR >

R205 1-249-441-11 CARBON 100K 5% 1/4WR206 1-249-429-11 CARBON 10K 5% 1/4WR207 1-249-429-11 CARBON 10K 5% 1/4WR208 1-249-429-11 CARBON 10K 5% 1/4WR209 1-249-441-11 CARBON 100K 5% 1/4W


R216 1-249-429-11 CARBON 10K 5% 1/4WR217 1-249-441-11 CARBON 100K 5% 1/4WR301 1-249-425-11 CARBON 4.7K 5% 1/4W FR302 1-249-437-11 CARBON 47K 5% 1/4WR303 1-249-413-11 CARBON 470 5% 1/4W F

R304 1-215-886-11 METAL OXIDE 100 5% 2WR305 1-249-437-11 CARBON 47K 5% 1/4WR306 1-249-425-11 CARBON 4.7K 5% 1/4W FR307 1-249-425-11 CARBON 4.7K 5% 1/4W F

0R308 1-234-182-11 ENCAPSULATED COMPONENT

R309 1-247-809-81 CARBON 120 5% 1/4W F(WMSP85)

R309 1-249-409-11 CARBON 220 5% 1/4W F(WMSP75)

R310 1-249-393-11 CARBON 10 5% 1/4W FR311 1-215-868-00 METAL OXIDE 680 5% 1WR312 1-249-433-11 CARBON 22K 5% 1/4W

R313 1-249-429-11 CARBON 10K 5% 1/4W(WMSP75)

R313 1-249-433-11 CARBON 22K 5% 1/4W(WMSP85)

0R314 1-217-637-00 FUSIBLE 1 5% 1/4WR315 1-249-437-11 CARBON 47K 5% 1/4WR401 1-215-892-11 METAL OXIDE 1K 5% 2W

R402 1-215-892-11 METAL OXIDE 1K 5% 2W0R403 1-219-153-11 FUSIBLE 10 5% 1/4W

(WMSP75)0R404 1-219-153-11 FUSIBLE 10 5% 1/4W

(WMSP85)R500 1-249-421-11 CARBON 2.2K 5% 1/4W FR501 1-249-429-11 CARBON 10K 5% 1/4W


R507 1-249-425-11 CARBON 4.7K 5% 1/4W FR508 1-249-417-11 CARBON 1K 5% 1/4W FR601 1-215-894-11 METAL OXIDE 2.2K 5% 2W

(WMSP75)R601 1-215-920-11 METAL OXIDE 3.3K 5% 3W

(WMSP85)

< RELAY >

RY301 1-515-920-11 RELAY************************************************************

POWER TRANS BOARD*******************

< CAPACITOR >

0C2 1-113-924-11 CERAMIC 0.0047uF 20.00% 250V

< CONNECTOR >

CN1 1-564-321-00 PIN, CONNECTOR (3.96mm PITCH) 2P* CN2 1-580-230-11 PIN, CONNECTOR (PC BOARD) 2P

MAIN POWER TRANSVer 1.2 2003.06

Ref. No. Part No. Description Remarks

11

SA-WMSP75/WMSP85

SWITCH



< FUSE HOLDER >

FH901 1-533-399-11 FUSE HOLDERFH902 1-533-399-11 FUSE HOLDER (E2)FH951 1-533-399-11 FUSE HOLDERFH952 1-533-399-11 FUSE HOLDER (E2)

< SWITCH >

0S2 1-572-675-11 SWITCH, POWER VOLTAGE CHANGE(VOLTAGE SELECTOR)(E2)

************************************************************

SWITCH BOARD*************

< CAPACITOR >

0C901 1-113-924-11 CERAMIC 0.0047uF 20.00% 250V

< CONNECTOR >

CN3 1-564-321-00 PIN, CONNECTOR (3.96mm PITCH) 2P* CN901 1-564-517-11 PLUG, CONNECTOR 2P

< DIODE >

D901 8-719-058-03 DIODE SEL5423E-TP15 (POWER)

< SWITCH >

0S901 1-554-920-11 SWITCH, PUSH (AC POWER)(1 KEY)(POWER)************************************************************

MISCELLANEOUS**************

057 1-696-847-11 CORD, POWER (AUS)057 1-769-744-11 CORD, POWER (AEP,UK,SP)057 1-783-532-11 CORD, POWER (US,CND,MX)057 1-792-823-12 CORD, POWER (TRACKING) (E2)0F901 1-533-450-11 FUSE, GLASS TUBE 2.5A/125V (US,CND,MX)

0F901 1-532-463-51 FUSE T1AL / 250V (EXCEPT : US,CND,MX)0F902 1-532-464-31 FUSE T2.5AL /250V (E2)

SP1 1-529-995-12 SPEAKER (20cm)(WMSP75)SP1 1-825-004-13 SPEAKER (20cm)(WMSP85)

0T1 1-439-625-11 POWER TRANSFORMER (WMSP85 : US,CND,MX)

0T1 1-439-628-11 POWER TRANSFORMER (WMSP75 : US,CND)0T1 1-439-623-11 POWER TRANSFORMER (E2)0T1 1-439-624-11 POWER TRANSFORMER (AEP,UK,SP,AUS)

Ver 1.2 2003.06POWER TRANS

SA-WMSP75/WMSP85

REVISION HISTORY

Clicking the version allows you to jump to the revised page.Also, clicking the version at the upper right on the revised page allows you to jump to the next revisedpage.

Ver. Date Description of Revision

1.0 2003.02 New

1.1 2003.04 SA-WMSP85 US model addition

1.2 2003.06 SA-WMSP85 Canadian model addition

1.3 2003.12 Addition of the Part No. for Ref No.1 (Grille Net, BLACK) (SPM-03125)

1.4 2004.01 Correction of the description of the composition on the cover

(SPM-04001)

Documents

SA-WMSP75/WMSP85 - Philips Parts and Accessories Corporation Home Audio Company ... STK404-130S 1SS133T-72 1SS133T-72 100 10V 120 ... SA-WMSP75/WMSP85