of 50 /50
SafeCom Go HP Hardware Quick Guide D10702-20 January 2012

SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

  • Upload
    doanh

  • View
    225

  • Download
    0

Embed Size (px)

Citation preview

Page 1: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

SafeCom Go HP Hardware Quick Guide D10702-20

January 2012

Page 2: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 2

Trademarks: SafeCom, SafeCom Go, SafeCom P:Go, SafeCom ePay and the SafeCom logo are trademarks of SafeCom a/s. Company and product names mentioned in this manual are trademarks or registered trademarks of their respective owners. SafeCom a/s cannot be held responsible for any technical or typographical errors and reserves the right to make changes to products and documentation without prior notification. Third Party Software: This software may contain third party software which requires notices and/or additional terms and conditions. Such required third party software notices and/or additional terms and conditions are located in the SafeCom Third Party Notice document. Patent: SafeCom has received the following British patent GB 2350 713 B, US patent US 6,952,780 B2 and Europe EUR EP1 120 701. Feedback: If you have any feedback or ideas concerning this manual or the SafeCom product, then please send an e-mail to [email protected] © Copyright 1999 - 2012 SafeCom a/s

SafeCom a/s

Lautrupvang 12 DK-2750 Ballerup Denmark Phone: +45 4436 0240 E-mail: [email protected] Web: safecom.eu

Page 3: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 3

Table of contents

1 Introduction ............................................................................................4 1.1 Device models .............................................................................. 4 1.2 SafeCom ID Devices ........................................................................ 6 1.3 Items supplied .............................................................................. 7

2 Hardware installation ................................................................................8 2.1 SafeCom HP USB ID Kit installation ..................................................... 8 2.2 SafeCom HP FMC ID Kit installation ..................................................... 9 2.3 HP LaserJet M3035 MFP, CM4730 MFP, M5035 MFP, M5039 MFP, CM6030 MFP,

CM6040 MFP, CM6049 MFP, CM8050 MFP, CM8060 MFP, M9040 MFP, M9050 MFP, M9059 MFP, M601, and 9250C Digital Sender ................................... 9

2.4 HP LaserJet P3015, CM3530 MFP, CM4540 MFP, M4555 MFP, M551, M602, M603, and Scanjet 7000n ....................................................................... 10 2.4.1 Embedded mini-USB E12 ID device .................................... 11 2.4.2 External USB ID device .................................................. 13

2.5 HP LaserJet M4345 MFP and M4349 MFP ............................................. 14 2.6 HP LaserJet 4345mfp .................................................................... 17 2.7 HP Color LaserJet 4730mfp ............................................................ 20 2.8 HP LaserJet 9040mfp, 9050mfp, 9040, 9050 ........................................ 22 2.9 HP Color LaserJet 9500mfp ............................................................ 24 2.10 HP LaserJet 4100mfp .................................................................... 26 2.11 HP LaserJet 9000mfp and 9000lmfp .................................................. 30 2.12 HP LaserJet 2410, 2420 and 2430 ..................................................... 33 2.13 HP Color LaserJet 3000, CP3505, CP3525 and 3800 ................................ 35 2.14 HP LaserJet P3005 ....................................................................... 37 2.15 HP LaserJet P4014, P4015, P4515, P4525 and CP6015 ............................ 38 2.16 HP LaserJet 4200 and 4300 ............................................................. 39 2.17 HP LaserJet 4250 and 4350 ............................................................. 42 2.18 HP Color LaserJet 4700 ................................................................. 44 2.19 HP Color LaserJet 4600, 5500 and 9500 .............................................. 46 2.20 HP Color LaserJet 4650 and 5550 ..................................................... 49

Page 4: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 4

1 Introduction This Quick Guide explains in detail how to install SafeCom Go hardware. The installation of SafeCom G3 software and subsequent configuration and use of the SafeCom Go HP product is described in SafeCom Go HP Administrator’s Manual D60701.

1.1 Device models

Table 1 - HP LaserJet MFPs

HP MFP Media slot Section

HP Color LaserJet CM4540 MFP USB (E12) 2.4

HP LaserJet M4555 MFP USB (E12) 2.4

HP LaserJet M3035 MFP USB 2.3

HP Color LaserJet CM3530 MFP USB (E12) 2.4

HP LaserJet 4100mfp DIMM 2.10

HP LaserJet M4345 MFP USB (no external) 2.5

HP LaserJet M4349 MFP USB (no external) 2.5

HP LaserJet 4345mfp FMC 2.6

HP LaserJet CM4730 MFP USB 2.3

HP Color LaserJet 4730mfp USB and FMC 2.7

HP LaserJet M5035 MFP USB 2.3

HP LaserJet M5039 MFP USB 2.3

HP Color LaserJet CM6030 MFP USB 2.3

HP Color LaserJet CM6040 MFP USB 2.3

HP Color LaserJet CM6049 MFP USB 2.3

HP LaserJet CM8050 MFP USB 2.3

HP LaserJet CM8060 MFP USB 2.3

HP LaserJet 9000mfp DIMM 2.11

HP LaserJet 9000lmfp DIMM 2.11

HP LaserJet M9040 MFP USB 2.3

HP LaserJet 9040mfp FMC 2.8

HP LaserJet M9050 MFP USB 2.3

HP LaserJet M9059 MFP USB 2.3

HP LaserJet 9050mfp FMC 2.8

HP Color LaserJet 9500mfp FMC 2.8

Table 2 - HP Scanners

HP Scanner Media slot Section

HP ScanJet Enterprise 7000n USB (E12f) 2.4

HP 9250C Digital Sender USB 2.3

Page 5: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 5

Table 3 - HP LaserJet printers

HP device Media slot Section

HP Color LaserJet CP5525 USB (E12) 2.4

HP LaserJet 500 Color M551 * USB (E12) 2.4

HP LaserJet 600 M601 ** USB 2.3

HP LaserJet 600 M602 USB (E12f) 2.4

HP LaserJet 600 M603 USB (E12f) 2.4

HP LaserJet 2410 FMC 2.12

HP LaserJet 2420 FMC 2.12

HP LaserJet 2430 FMC 2.12

HP Color LaserJet 3000 USB 2.13

HP LaserJet P3005 USB (no external) 2.14

HP LaserJet P3015 USB (E12) 2.4

HP Color LaserJet CP3505 USB (no external) 2.13

HP Color LaserJet CP3525 USB 2.13

HP Color LaserJet 3800 USB 2.13

HP LaserJet P4014 USB 2.15

HP LaserJet P4015 USB 2.15

HP LaserJet 4200 DIMM 2.16

HP LaserJet 4250 FMC 2.17

HP LaserJet 4300 DIMM 2.16

HP LaserJet 4350 FMC 2.17

HP LaserJet P4515 USB 2.15

HP Color LaserJet P4525 USB 2.15

HP Color LaserJet 4650 FMC 2.18

HP Color LaserJet 4700 USB and FMC 2.18

HP Color LaserJet 5500 DIMM 2.19

HP Color LaserJet 5550 FMC 2.18

HP Color LaserJet CP6015 USB 2.15

HP LaserJet 9040 FMC 2.8

HP LaserJet 9050 FMC 2.8

HP Color LaserJet 9500 DIMM 2.19

* The Hardware Integration Pocket is not available for M551n. ** There is no Hardware Integration Pocket for this printer.

Page 6: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 6

1.2 SafeCom ID Devices

Table 4 - SafeCom Go HP supported SafeCom ID Devices

Identification Method USB

p/n

Serial

p/n

Mini-USB E12 p/n

SafeCom AWID Reader 696020 696010

SafeCom Barcode Reader 694020 694010

SafeCom Casi-Rusco Reader 652420 652010

SafeCom Cotag Reader 678020

SafeCom EM Reader [E] SafeCom EM Reader [R]

674120 674420

674110 674220

SafeCom Felica Reader 697420 697410

SafeCom HID Reader 35 bit [E] SafeCom HID Reader 35 bit [R]

673120 673420

673110 673220

SafeCom HID Reader 37 bit 671120 671110 671220

SafeCom iCLASS Reader [E] SafeCom iCLASS Reader [R]

654120 654420

654110 654220

SafeCom Indala Reader 26bit 670420 670010

SafeCom Indala Reader 29bit 651020 651010

SafeCom IoProx 658420 658010

SafeCom Legic Reader [E] SafeCom Legic Reader [R]

679120 679420

679110 679220

SafeCom Magnetic Card Reader (Tr 1) 959010

SafeCom Magnetic Card Reader (Tr 2) 954010

SafeCom Magnetic Card Reader (Tr 3) 657010

SafeCom Magnetic Card Reader DD (Tr 1) 692010

SafeCom Magnetic Card Reader DD (Tr 2) 691020

SafeCom Magnetic Card Reader DD (Tr 3) 692020

SafeCom Mifare Reader [E] SafeCom Mifare Reader [R]

970120 970420

970110 970220

SafeCom Nedap Reader 653020 978990

SafeCom NexWatch Reader 698420 698010

Page 7: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 7

1.3 Items supplied

SafeCom HP USB Key:

USB Key. SafeCom HP USB ID Kit:

USB ID Kit with cable (40 cm) for connection to internal USB port.

Figure 1 SafeCom HP USB ID Kit & USB Key.

SafeCom HP with FMC ID Kit:

Flash Memory Card.

FMC ID Kit with cable (40 cm) for connection to Flash Memory Card.

Power supply (Input: 100-240V~, 50-60Hz/150mA, Output: 5V, 1.0A).

SafeCom ID Device must be ordered separately. Connects to the RS232/PS2 (6 pin mini-DIN) connector on the FMC ID Kit.

Figure 2 SafeCom HP FMC ID Kit.

Page 8: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 8

2 Hardware installation

2.1 SafeCom HP USB ID Kit installation

The SafeCom HP USB installation can be simplified depending on the capabilities of the device and if a SafeCom ID Device (card reader) is required to identify users.

The device is equipped with a hard disk (incl. HDD or SSD). You may skip step 3 (SafeCom HP USB Key installation) as the SafeCom Go HP software can be loaded onto and run from the device’s hard disk.

The device has an external USB port labeled ACC. You may skip step 4 and 5 (SafeCom HP USB ID Kit installation) and connect the SafeCom ID Device directly to the device’s external USB port.

The device has a hardware integration pocket. Please proceed to the model specific section (2.3 - 2.20).

Install the SafeCom HP USB Key: 1. Turn the device off and disconnect all power and interface cables. 2. Get access to the device’s formatter board as described in the device’s

manual. 3. Insert the SafeCom HP USB Key into an available internal USB port. Install SafeCom HP USB ID Kit: 4. Remove metal plate that covers empty EIO slot and slide the SafeCom HP

ID Kit into the EIO slot. If an HP JetDirect network card occupies an EIO slot you may replace the JetDirect bracket with the SafeCom HP ID Kit bracket. Use the supplied screwdriver with Torx 8 bit.

5. Connect the ID Kit’s USB cable to the device’s internal USB port. 6. Reverse the procedure you used in step 2 to get access to the device’s

formatter board. In other words reassemble the device. Install SafeCom ID Device: 7. Connect the SafeCom ID Device to the external USB port labeled ACC or

to the USB port on the SafeCom HP ID Kit. A label covering the USB port may have to be removed first. Note: With the exception of MFPs most HP devices do not support hot swap of USB devices and therefore the SafeCom ID Device must be present during power on.

8. Plug in the power cord and connect all cables. Turn the device on.

Page 9: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 9

2.2 SafeCom HP FMC ID Kit installation

Install the SafeCom HP Flash Memory Card: 1. Turn the device off and disconnect all power and interface cables. 2. Get access to the device’s formatter board as described in the device’s

manual. 3. Press the SafeCom HP Flash Memory Card straight into an available slot.

Do NOT use the slot labeled FIRMWARE SLOT or SYSTEM CODE. If it does not go in easily, rotate it 180 degrees and try to insert it again.

Install SafeCom HP FMC ID Kit: 4. Remove metal plate that covers empty EIO slot and slide the SafeCom HP

ID Kit into the EIO slot. If an HP JetDirect network card occupies an EIO slot you may replace the JetDirect bracket with the SafeCom HP FMC ID Kit bracket. Use the supplied screwdriver with Torx 8 bit.

5. Connect the white female connector at the end of the cable to the corresponding male 8-pin connector on the SafeCom HP Flash Memory Card. It only fits in one way.

6. Reverse the procedure you used in step 2 to get access to the device’s

formatter board. In other words reassemble the device. Install SafeCom ID Device: 7. Connect SafeCom ID Device to the serial port of the SafeCom HP ID Kit. 8. Connect the external power supply (5V, 1.0A) to the SafeCom HP ID Kit. 9. Plug in the power cord and connect all cables. Turn the device on.

2.3 HP LaserJet M3035 MFP, CM4730 MFP, M5035 MFP, M5039 MFP, CM6030 MFP, CM6040 MFP, CM6049 MFP, CM8050 MFP, CM8060 MFP, M9040 MFP, M9050 MFP, M9059 MFP, M601, and 9250C Digital Sender

1. Connect the SafeCom USB ID Device directly to the external USB port labeled ACC.

Note: A label covering the USB port may have to be removed first. On

M602 the USB port is hidden behind an USB icon at the rear of the printer at must be cut clear in order to install the USB ID Device.

You have now completed the hardware installation and can continue with the subsequent software installation and configuration of the SafeCom Go HP product as described in SafeCom Go HP Administrator’s Manual D60701.

Page 10: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 10

2.4 HP LaserJet P3015, CM3530 MFP, CM4540 MFP, M4555 MFP, M551, M602, M603, and Scanjet 7000n

The devices features a hardware integration pocket that can be used to embed a SafeCom embedded ID device, also known as E12, as it is embedded and supplied with a 12 cm cable.

Figure 3 SafeCom "Present card here" label (p/n 621010) optionally mounted on the cover of the hardware integration pocket on

the HP Color LaserJet CM3530 MFP. In Table 4 on page 6 there is a list of the available mini-USB E12 ID devices. If the choice of identification method is not supported by a mini-USB E12 ID device it is necessary to install a USB ID Kit with cable for connection to one of the MFP’s two internal USB ports. To summarize there are two installation scenarios:

Installation of embedded mini-USB E12 ID device (2.4.1)

Installation of external USB ID device (2.4.2)

Page 11: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 11

2.4.1 Embedded mini-USB E12 ID device

Items supplied:

One ID device without casing.

One 12 cm mini-USB cable for mounting on the ID device.

Four holders with self adhesive tape.

One “Present card here” label (p/n 621010). Installation: 1. Turn the device off and disconnect all power and interface cables. 2. Remove the cover from the hardware integration pocket as described in

the device’s manual. Opening the cover can be done by inserting a metal blade at the center of the top edge of the cover. Take care not to scratch the cover or hurt yourself.

3. Hold the ID device with the cable connector facing upwards and the antenna facing downwards. On the cable connector side place a holder in each of the four corner holes.

4a. CM3530 MFP, CM4540 MFP, and M4555 MFP: Connect the 12 cm mini-USB cable to the ID device and to the mini-USB connector in the lower right corner of the pocket.

4b. P3015: Disconnect the 12 cm mini-USB cable from the ID device. Connect the supplied 33 cm cable (p/n 344020) to the ID device and to the USB connector on the device’s motherboard. Pass the cable through the square hole in the hardware integration pocket.

4c. M551: Connect the 12 cm mini-USB cable to the ID device and to the mini-USB connector in the lower right corner of the pocket.

Note: For M551 the Hardware Integration Pocket is not available for the M551n.

4d. M602, and M603: Connect the card reader using the E12 USB Cable, Female, 12 cm cable (p/n 344030). Note: For the M601 there is no Hardware Integration Pocket.

4e. Scanjet 7000n: Connect the card reader using the E12 USB Cable, Female, 12 cm cable (p/n 344030).

5. Remove the tape from the four holders mounted on the ID device.

Page 12: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 12

6. Center and mount the ID device in the bottom of the pocket. The cable connector on the ID device should face left and downwards.

Figure 4 SafeCom ID device mounted in the hardware integration pocket. The shown ID device is SafeCom Mifare Reader. Other SafeCom ID devices may have the antenna layered in the print circuit board.

7. Plug in the power cord and connect all cables. Turn the device on. 8. Verify that the LED on the ID device is on. 9. Put the cover back on the hardware integration pocket (it can only fit one

way). 10. Remove the plastic from the “Present card here” and mount it centered

on the cover of the hardware integration pocket.

Page 13: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 13

2.4.2 External USB ID device

1. Turn the device off and disconnect all power and interface cables. 2. Get access to the device’s formatter board as described in the device’s

manual. 3. Remove the metal plate that covers empty EIO slot. 4. Slide SafeCom HP USB ID Kit into the EIO slot. Tighten the two screws. 5. Connect the ID Kit’s USB cable to the device’s internal USB port and

connect the SafeCom ID Device to the USB port of the SafeCom HP ID Kit mounted in the EIO slot.

6. Reverse the procedure you used in step 2 to get access to the device’s formatter board. In other words reassemble the device

7. Connect the SafeCom ID Device to the external USB port. 8. Plug in the power cord and connect all cables. Turn the device on. .

Page 14: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 14

2.5 HP LaserJet M4345 MFP and M4349 MFP

1. Turn the device off and disconnect all power and interface cables.

2. Remove the output bin, the 3-bin mailbox, or the stapler/stacker.

3. At the back of the device, remove the formatter cover.

4. Open the formatter door.

Page 15: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 15

Additional steps to install USB ID Kit: a. Remove the metal plate that covers empty EIO slot. b. Slide SafeCom HP ID Kit into the EIO slot. Tighten the two screws. c. Connect the ID Kit’s USB cable to the device’s internal USB port and

connect the SafeCom ID Device to the USB port of the SafeCom ID Kit mounted in the EIO slot.

5. Close the formatter door.

6. Replace the formatter cover.

Page 16: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 16

7. Reinstall the output bin, the 3-bin mailbox, or the stapler/stacker.

8. Reconnect all the cables and turn on the device.

You have now completed the hardware installation and can continue with the subsequent software installation and configuration of the SafeCom Go HP product as described in SafeCom Go HP Administrator’s Manual D60701.

Page 17: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 17

2.6 HP LaserJet 4345mfp

1. Turn the device off and disconnect all power and interface cables.

2. Remove the output bin, the 3-bin mailbox, or the stapler/stacker.

3. At the back of the device, remove the formatter cover.

4. Open the formatter door.

5. Hold the SafeCom Go Flash Memory Card with fingers against the side edges and thumbs against the back edge. Align the notches on the SafeCom Go Flash Memory Card with the compact flash slot.

Page 18: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 18

6. Press the SafeCom Go Flash Memory Card straight into slot 2 or 3. Do NOT use the slot labeled FIRMWARE SLOT. If it does not go in easily, rotate it 180 degrees and try to insert it again.

Additional steps to install the SafeCom Go product with ID Kit: a. Remove metal plate that covers empty EIO slot. b. Slide SafeCom Go ID Kit into the EIO slot. Tighten the two screws. c. Connect the white female connector at the end of the cable to the

corresponding male 8-pin connector on the SafeCom Go Flash Memory Card. It only fits in one way.

7. Close the formatter door.

8. Replace the formatter cover.

9. Reinstall the output bin, the 3-bin mailbox, or the stapler/stacker.

10. Connect SafeCom ID Device to the serial port of the SafeCom ID Kit mounted in the EIO slot.

Page 19: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 19

11. Reconnect all the cables and turn on the device.

You have now completed the hardware installation and can continue with the subsequent software installation and configuration of the SafeCom Go HP product as described in SafeCom Go HP Administrator’s Manual D60701.

Page 20: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 20

2.7 HP Color LaserJet 4730mfp

Note: If you intend to use a SafeCom USB ID Device for user identification you can connect the SafeCom USB ID Device directly to the external USB port labeled ACC and power cycle the device (2.3). Otherwise you should follow the steps below.

1. Turn the device off.

2. Disconnect all power and interface cables.

3. Locate the formatter board in the rear of the device.

4. Gently pull on the black tabs to pull the formatter board from the device. Place the formatter board on a clean, flat, grounded surface.

Page 21: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 21

5. Align the groove on the side of the SafeCom Go Flash Memory Card with the notches in the connector and push it in the slot until it is fully seated in slot 2 or 3. Do NOT use the slot labeled FIRMWARE SLOT. If it does not go in easily, rotate it 180 degrees and try to insert it again.

Additional steps to install the SafeCom Go product with ID Kit: a. Remove metal plate that covers empty EIO slot. b. Slide SafeCom Go ID Kit into the EIO slot. Tighten the two screws. c. Connect the white female connector at the end of the cable to the

corresponding male 8-pin connector on the SafeCom Go Flash Memory Card. It only fits in one way.

6. Align the formatter board in the tracks at the top and bottom of the slot, and then slide the board back into the device.

7. Connect SafeCom Serial ID Device to the serial port of the SafeCom ID Kit mounted in the EIO slot.

8. Reconnect the power cable and interface cables, and turn the device on.

You have now completed the hardware installation and can continue with the subsequent software installation and configuration of the SafeCom Go HP product as described in SafeCom Go HP Administrator’s Manual D60701.

Page 22: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 22

2.8 HP LaserJet 9040mfp, 9050mfp, 9040, 9050

1. Turn the device off and disconnect all power and interface cables.

2. Loosen the two captive thumbscrews on the back of the device.

3. Grasp the screws and pull the formatter board out of the device. Place it on a flat, nonconductive surface.

4. Hold the SafeCom Go Flash Memory Card with fingers against the side edges and thumbs against the back edge. Align the notches on the SafeCom Go Flash Memory Card with the compact flash slot.

5. Press the SafeCom Go Flash Memory Card straight into slot 2 or 3. Do NOT use the slot labeled FIRMWARE SLOT. If it does not go in easily, rotate it 180 degrees and try to insert it again.

Page 23: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 23

Additional steps to install the SafeCom Go product with ID Kit: a. Remove metal plate that covers empty EIO slot. b. Slide SafeCom Go ID Kit into the EIO slot. Tighten the two screws. c. Connect the white female connector at the end of the cable to the

corresponding male 8-pin connector on the SafeCom Go Flash Memory Card. It only fits in one way.

6. Slide the formatter board back into the device and tighten the two screws.

7. Connect SafeCom ID Device to the serial port of the SafeCom ID Kit mounted in the EIO slot.

8. Plug in the power cord and connect all cables. Turn on the device.

You have now completed the hardware installation and can continue with the subsequent software installation and configuration of the SafeCom Go HP product as described in SafeCom Go HP Administrator’s Manual D60701.

Page 24: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 24

2.9 HP Color LaserJet 9500mfp

1. Turn the device off and disconnect the power cord from the outlet.

2. Remove the eight screws on the back of the formatter board.

3. Grasp the handle and pull the formatter board out of the device. Place it on a flat, nonconductive surface.

4. Hold the SafeCom Go Flash Memory Card with fingers against the side edges and thumbs against the back edge. Align the notches on the SafeCom Go Flash Memory Card with the compact flash slot.

Press the SafeCom Go Flash Memory Card straight into slot 2 or 3. Do NOT use the slot labeled FIRMWARE SLOT. If it does not go in easily, rotate it 180 degrees and try to insert it again

Additional steps to install the SafeCom Go product with ID Kit: a. Remove the JetDirect Card. Replace the bracket with the bracket of the

SafeCom Go ID Kit (use the supplied screw driver) b. Slide SafeCom Go ID Kit into the EIO slot. Tighten the two screws. c. Connect the white female connector at the end of the cable to the

corresponding male 8-pin connector on the SafeCom Go Flash Memory Card. It only fits in one way.

Page 25: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 25

5. Holding the black tab near the top, slide the formatter board back into the device and tighten the eight screws.

6. Plug in the power cord and connect all cables.

7. Connect SafeCom ID Device to the serial port of the SafeCom ID Kit mounted in the EIO slot.

8. Turn on the device.

You have now completed the hardware installation and can continue with the subsequent software installation and configuration of the SafeCom Go HP product as described in SafeCom Go HP Administrator’s Manual D60701.

Page 26: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 26

2.10 HP LaserJet 4100mfp

Caution: DIMM boards and your device formatter board can be damaged by small amounts of static electricity. When handling a DIMM or other board, wear an antistatic wrist strap connected to the metal frame of the device (or to your antistatic system). During installation, to prevent generation of static electricity, avoid moving about the work area.

1. Turn the device off. Unplug the power cord and disconnect any cables. Remove the formatter cover by pulling it firmly toward the back of the device until the cover stops.

2. Remove the cover from the device.

3. Open the DIMM access door by pulling on the large metal tab.

4. Open any of the three upper DIMM slots.

Page 27: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 27

5. Remove the new DIMM from the antistatic package. Hold the DIMM with your fingers against the side edges and your thumbs against the back edge. Align the notches on the DIMM with the DIMM slot. (Make sure that the locks on each side of the DIMM are open, or outward.)

6. Press the DIMM straight into the appropriate slot. Press firmly. Make sure that the locks on each side of the DIMM snap inward into place.

Additional steps to install the SafeCom Go product with ID Kit: a. Pull the JetDirect Card out of EIO slot 2. b. Remove bracket from JetDirect Card by loosening the two screws. c. Mount JetDirect Card onto the SafeCom Go bracket by tightening the two

screws. d. Slide JetDirect back into EIO slot 2. e. Connect the flat cable to the 11 pin connector on the SafeCom Go ID Kit

and the SafeCom Go DIMM. It only fits in one way.

Figure 5 SafeCom Go DIMM and SafeCom Go ID Kit installed

Page 28: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 28

7. Close the DIMM access door. Make sure that it locks into place.

8. Insert the bottom of the cover into the slot and rotate the cover upward.

9. Slide the cover toward the front of the device until the cover clicks into place. Plug in the power cord, reconnect all cables, and turn the device on.

Additional steps to install the SafeCom Go product with ID Kit: a. Connect SafeCom Identification Device (card reader) to the serial port of

the SafeCom Go ID Kit mounted in the EIO slot 2.

Page 29: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 29

Figure 6 SafeCom Go with ID Kit installed

You have now completed the hardware installation and can continue with the subsequent loading of SafeCom Go HP software and configuration as described in SafeCom Go HP Administrator’s Manual D60701.

Page 30: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 30

2.11 HP LaserJet 9000mfp and 9000lmfp

Caution: DIMM boards and your device formatter board can be damaged by small amounts of static electricity. When handling a DIMM or other board, wear an antistatic wrist strap connected to the metal frame of the device (or to your antistatic system). During installation, to prevent generation of static electricity, avoid moving about the work area.

1. Turn the device off. Disconnect the power cord and any cables.

2. Loosen the two captive thumbscrews on the back of the device.

3. Grasp the screws and pull the formatter board out of the device. Place it on a flat, non-conductive surface.

4. Remove the DIMM from the antistatic package. Hold the DIMM with fingers against the side edges and thumbs against the back edge. Align the notches on the DIMM with the DIMM slot. (Check that the locks on each side of the DIMM slot are open, or outward.)

5. Press the DIMM straight into the slot (press firmly). Make sure the locks on each side of the DIMM snap inward into place. (To remove a DIMM, the locks must be released.)

Page 31: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 31

Additional steps to install the SafeCom Go product with ID Kit: a. Pull the JetDirect Card out of EIO slot 1 and Hard disk out of EIO slot 2. b. Remove bracket from the JetDirect Card by loosening the two screws. c. Mount the JetDirect Card onto the SafeCom Go ID Kit by tightening the

two screws. d. Slide the JetDirect Card into EIO slot 2 and the Hard disk into EIO slot 1. e. Connect the flat cable to the 11 pin connector on the SafeCom Go ID Kit

and the SafeCom Go DIMM. It only fits in one way.

Figure 7 SafeCom Go DIMM and SafeCom Go ID Kit installed.

6. Slide the formatter board back into the device and tighten the two screws.

7. Plug in the power cord and connect all cables. Turn the device on.

Page 32: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 32

Additional steps to install the SafeCom Go product with ID Kit: a. Connect SafeCom Identification Device (card reader) to the serial port of

the SafeCom Go ID Kit mounted in the EIO slot 2.

Figure 8 SafeCom Go with ID Kit installed

You have now completed the hardware installation and can continue with the subsequent loading of SafeCom Go HP software and configuration as described in SafeCom Go HP Administrator’s Manual D60701.

Page 33: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 33

2.12 HP LaserJet 2410, 2420 and 2430

1. Turn the device power off.

2. Unplug the power cord and disconnect any cables. 2

3. Remove the right side panel by sliding it towards the rear of the device until the side slides free from the device.

4. Open the access door by pulling on the metal tab.

5. Hold the SafeCom Go Flash Memory Card by its edges and line up the grooves in the side of the card with the tabs in the available card slot. Do NOT use the slot labeled FIRMWARE SLOT or SYSTEM CODE.

Additional steps to install the SafeCom Go product with ID Kit: a. Remove the JetDirect Card. Replace the bracket with the bracket of the

SafeCom Go ID Kit (use the supplied screw driver) b. Slide SafeCom Go ID Kit into the EIO slot. Tighten the two screws. c. Connect the white female connector at the end of the cable to the

corresponding male 8-pin connector on the SafeCom Go Flash Memory Card. It only fits in one way.

Page 34: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 34

6. Close the access door, and press firmly until it snaps into place. 8

7. To replace the right side panel, line up the alignment arrows and slide the panel toward the front of the device until it latches into place.

8. Reattach any cables and the power cord.

9. Connect SafeCom ID Device to the serial port of the SafeCom ID Kit mounted in the EIO slot.

10. Turn the device power on.

You have now completed the hardware installation and can continue with the subsequent software installation and configuration of the SafeCom Go HP product as described in SafeCom Go HP Administrator’s Manual D60701.

Page 35: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 35

2.13 HP Color LaserJet 3000, CP3505, CP3525 and 3800

Note: If the device has a hard disk then you can connect the SafeCom USB ID Device directly to the external USB port labeled ACC and power cycle the device (2.3). Otherwise you should follow the steps below.

1. Turn the device off. Disconnect all power and interface cables.

2. Gently pull on the black tabs to pull the formatter board from the device. Place the formatter board on a clean, flat, grounded surface.

3. Insert the SafeCom HP USB Key into an available USB port.

4. Align the formatter board in the tracks at the top and bottom of the slot, and then slide the board back into the device.

Page 36: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 36

5. Reconnect the power cable and interface cables

6. Connect SafeCom ID Device to the device’s USB port. The USB port is accessible from the outside and is labeled ACC.

7. Turn the device on.

You have now completed the hardware installation and can continue with the subsequent software installation and configuration of the SafeCom Go HP product as described in SafeCom Go HP Administrator’s Manual D60701.

Page 37: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 37

2.14 HP LaserJet P3005

1. Turn the device off and disconnect all power and interface cables.

2. Get access to the device’s formatter board as described in the device’s manual.

3. Insert the SafeCom Go USB Key into an available internal USB port.

4. Remove metal plate that covers empty EIO slot and slide the SafeCom Go ID Kit into the EIO slot.

5. Connect the ID Kit’s USB cable to the device’s internal USB port.

6. Reverse the procedure you used in step 2 to get access to the device’s formatter board. In other words reassemble the device

7. Connect the SafeCom ID Device to the USB port on the SafeCom Go ID Kit

8. Plug in the power cord and connect all cables. Turn the device on.

You have now completed the hardware installation and can continue with the subsequent software installation and configuration of the SafeCom Go HP product as described in SafeCom Go HP Administrator’s Manual D60701.

Page 38: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 38

2.15 HP LaserJet P4014, P4015, P4515, P4525 and CP6015

Note: If the device has a hard disk then you can connect the SafeCom USB ID Device directly to the external USB port and power cycle the device (2.3). Otherwise you should follow the steps below.

1. Turn the device off and disconnect all power and interface cables.

2. Get access to the device’s formatter board as described in the device’s manual.

3. Insert the SafeCom Go USB Key into an available internal USB port.

4. Reverse the procedure you used in step 2 to get access to the device’s formatter board. In other words reassemble the device

5. Connect the SafeCom ID Device to the external USB port.

6. Plug in the power cord and connect all cables. Turn the device on.

You have now completed the hardware installation and can continue with the subsequent software installation and configuration of the SafeCom Go HP product as described in SafeCom Go HP Administrator’s Manual D60701.

Page 39: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 39

2.16 HP LaserJet 4200 and 4300

Caution: DIMM boards and your device formatter board can be damaged by small amounts of static electricity. When handling a DIMM or other board, wear an antistatic wrist strap connected to the metal frame of the device (or to your antistatic system). During installation, to prevent generation of static electricity, avoid moving about the work area.

1. Turn the device power off.

2. Unplug the power cord and disconnect any cables. 2

3. Grasp the cover on the right side of the device and pull it firmly toward the rear of the device until it stops.

4. Remove the cover from the device.

5. Open the access door by pulling on the metal tab.

Page 40: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 40

6. Remove the DIMM from the antistatic package. Hold the DIMM with your fingers against the side edges and thumbs against the back edge. Align the notches on the DIMM with the DIMM slot. (Check that the locks on each side of the DIMM slot are open, or outward.)

7. Press the DIMM straight into the slot (press firmly). Make sure the locks on each side of the DIMM snap inward into place. (To remove a DIMM, the locks must be released.)

CAUTION: Do not move or remove the DIMM in the upper slot.

Additional steps to install the SafeCom Go product with ID Kit: a. Mount the SafeCom Go bracket in the open EIO slot by tightening the two

screws. b. Connect the flat cable to the 11 pin connector on the SafeCom Go ID Kit

and the SafeCom Go DIMM. It only fits in one way.

8. Close the DIMM-access door. Make sure it locks into place.

8

9. Set the bottom of the cover onto the device. Make sure the bottom tab on the cover fits into the corresponding slot in the device. Rotate the cover up, toward the device.

10. Slide the cover toward the front of the device until it clicks into place.

Reattach any cables and the power cord and then turn the device power on.

Page 41: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 41

Additional steps to perform to install the SafeCom Go product with ID Kit: a. Connect SafeCom Identification Device (card reader) to the serial port of

the SafeCom Go ID Kit mounted in the EIO slot.

Figure 9 SafeCom Go with ID Kit installed

You have now completed the hardware installation and can continue with the subsequent loading of SafeCom Go HP software and configuration as described in SafeCom Go HP Administrator’s Manual D60701.

Page 42: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 42

2.17 HP LaserJet 4250 and 4350

1. Turn the device power off.

2. Unplug the power cord and disconnect any cables. 2

3. Grasp the cover on the right side of the device and pull it firmly toward the rear of the device until it stops.

4. Remove the cover from the device.

5. Open the access door by pulling on the metal tab.

6. Hold the SafeCom Go Flash Memory Card with fingers against the side edges and thumbs against the back edge. Align the notches on the SafeCom Go Flash Memory Card with the compact flash slot.

Press the SafeCom Go Flash Memory Card straight into the top slot. Do NOT use the bottom slot labeled SYSTEM CODE. If it does not go in easily, rotate it 180 degrees and try to insert it again.

Page 43: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 43

Additional steps to perform to install the SafeCom Go product with ID Kit: a. Remove the JetDirect Card. Replace the bracket with the bracket of the

SafeCom Go ID Kit (use the supplied screw driver) b. Slide SafeCom Go ID Kit into the EIO slot. Tighten the two screws. c. Connect the white female connector at the end of the cable to the

corresponding male 8-pin connector on the SafeCom Go Flash Memory Card. It only fits in one way.

7. Close the access door. Make sure it locks into place.

8

8. Set the bottom of the cover onto the device. Make sure the bottom tab on the cover fits into the corresponding slot in the device. Rotate the cover up, toward the device.

9. Slide the cover toward the front of the device until it clicks into place.

10. Connect SafeCom ID Device to the serial port of the SafeCom ID Kit mounted in the EIO slot.

11. Reattach any cables and the power cord and then turn the device power on.

You have now completed the hardware installation and can continue with the subsequent software installation and configuration of the SafeCom Go HP product as described in SafeCom Go HP Administrator’s Manual D60701.

Page 44: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 44

2.18 HP Color LaserJet 4700

Note: If the device has a hard disk then you can connect the SafeCom USB ID Device directly to the external USB port labeled ACC and power cycle the device. Otherwise you should follow the steps below.

1. Turn the device off.

2. Disconnect all power and interface cables.

3. Locate the formatter board in the rear of the device.

4. Gently pull on the black tabs to pull the formatter board from the device. Place the formatter board on a clean, flat, grounded surface.

Page 45: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 45

5. Align the groove on the side of the SafeCom Go Flash Memory Card with the notches in the connector and push it in the slot until it is fully seated in slot 2 or 3. Do NOT use the slot labeled FIRMWARE SLOT. If it does not go in easily, rotate it 180 degrees and try to insert it again.

Additional steps to perform to install the SafeCom Go Flash Memory Card product with ID Kit: a. Remove metal plate that covers empty EIO slot. b. Slide SafeCom Go ID Kit into the EIO slot. Tighten the two screws. c. Connect the white female connector at the end of the cable to the

corresponding male 8-pin connector on the SafeCom Go Flash Memory Card. It only fits in one way.

6. Align the formatter board in the tracks at the top and bottom of the slot, and then slide the board back into the device.

7. Connect SafeCom Serial ID Device to the serial port of the SafeCom ID Kit mounted in the EIO slot.

8. Reconnect the power cable and interface cables, and turn the device on.

You have now completed the hardware installation and can continue with the subsequent software installation and configuration of the SafeCom Go HP product as described in SafeCom Go HP Administrator’s Manual D60701.

Page 46: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 46

2.19 HP Color LaserJet 4600, 5500 and 9500

Caution: DIMM boards and your device formatter board can be damaged by small amounts of static electricity. When handling a DIMM or other board, wear an antistatic wrist strap connected to the metal frame of the device (or to your antistatic system). During installation, to prevent generation of static electricity, avoid moving about the work area.

1. Turn the device off. Disconnect the power cord and any cables.

2. Locate the formatter board in the rear of the device.

3. Remove the eight screws holding the board in place, and set them aside.

4. Slide out the formatter board and set it on a clean, flat, grounded surface.

5. Release the locks on each side of the DIMM slot.

Page 47: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 47

6. Remove the DIMM from the antistatic package. Locate the alignment notches on the bottom edge of the DIMM.

7. Holding the DIMM by the edges, align the notches on the DIMM with the bars in the DIMM slot.

8. Firmly press the DIMM straight into the slot. Close the locks on each side of the DIMM until they snap into place.

Additional steps to perform to install the SafeCom Go product with ID Kit: a. Pull the JetDirect Card out of the EIO slot. b. Remove bracket from JetDirect Card by loosening the two screws. c. Mount JetDirect Card onto the SafeCom Go bracket by tightening the two

screws. d. Slide the JetDirect Card into the EIO slot. e. Connect the flat cable to the 11 pin connector on the SafeCom Go ID Kit

and the SafeCom Go DIMM. It only fits in one way. f. Connect the cable to the SafeCom Go DIMM.

Page 48: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 48

Figure 10 SafeCom Go DIMM and SafeCom Go ID Kit installed.

9. Align the formatter board in the tracks at the top and bottom of the slot, and slide the board back into the device. Replace and tighten the eight screws removed in step 2.

10. Reconnect the power cable and interface cables, and turn the device on.

Additional steps to perform to install the SafeCom Go product with ID Kit: a. Connect SafeCom Identification Device (card reader) to the serial port of

the SafeCom Go ID Kit mounted in the EIO slot.

Figure 11 SafeCom Go with ID Kit installed

You have now completed the hardware installation and can continue with the subsequent loading of SafeCom Go HP software and configuration as described in SafeCom Go HP Administrator’s Manual D60701.

Page 49: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 49

2.20 HP Color LaserJet 4650 and 5550

1. Turn the device off. Disconnect the power cord and any cables.

2. Locate the formatter board in the rear of the device.

3. Remove the eight screws holding the board in place, and set them aside.

4. Slide out the formatter board and set it on a clean, flat, grounded surface.

5. Hold the SafeCom Go Flash Memory Card with fingers against the side edges and thumbs against the back edge. Align the notches on the SafeCom Go Flash Memory Card with the compact flash slot.

Press the SafeCom Go Flash Memory Card straight into slot 2 or 3. Do NOT use the slot labeled FIRMWARE SLOT. If it does not go in easily, rotate it 180 degrees and try to insert it again.

Page 50: SafeCom Go HP - Netprint Solution Go/SafeCom G… · HP Color LaserJet 3000 USB 2.13 HP LaserJet P3005 USB (no external) 2.14 HP LaserJet P3015 USB (E12) 2.4 HP Color LaserJet CP3505

D10702-20 50

Additional steps to perform to install the SafeCom Go product with ID Kit: a. Remove the JetDirect Card. Replace the bracket with the bracket of the

SafeCom Go ID Kit (use the supplied screw driver) b. Slide SafeCom Go ID Kit into the EIO slot. Tighten the two screws. c. Connect the white female connector at the end of the cable to the

corresponding male 8-pin connector on the SafeCom Go Flash Memory Card. It only fits in one way. Connect SafeCom ID Device to the serial port of the SafeCom ID Kit mounted in the EIO slot.

6. Align the formatter board in the tracks at the top and bottom of the slot, and then slide the board back into the device. Replace and tighten the eight screws removed in step 3.

7. Plug in the power cord and connect all cables. Turn on the device.

You have now completed the hardware installation and can continue with the subsequent software installation and configuration of the SafeCom Go HP product as described in SafeCom Go HP Administrator’s Manual D60701.