Sheet CAD02-SolidWorks 3D Modeling.pdf

8/20/2019 Sheet CAD02-SolidWorks 3D Modeling.pdf

1/228

INDIAN INSTITUTE OF TECHNOLOGY, BOMBAY Department of Mechanical Engineering

ME-119 Engineering Drawing & Graphics 2013-14 Semester II

Sheet CAD02: SolidWorks 3D Modeling

Note:

There is one problem assigned to each group in this sheet.

All the problems are given in 3rd angle projections.

The dimensions are to be taken from grid. One grid is of 10mm×10mm.

Construct the 3D model in SolidWorks and find the projections of that in 1st angle projection using SolidWorks 2D Drawings.

The submission must contain a)3D part in *.sldprt format b)Drawing in pdf format which

Will contain 1st angle projections and isometric projection of the 3D part as shown in the figure below.

Page size of drawing will be A3.

You will work in groups as assigned in CAD01. Each group will submit a common assignment. The name plate shall have both the names and their roll numbers. Each group will solve only problems assigned for their group in the corresponding tables. Question number is mentioned at the bottom of sheet.

Any discrepancies related to any problem statements or parameters shall be brought to the notice of onl y the instructors or RAs (Nitish Karvekar, Dhirendra Rana and Sandeep Shah) for correction immediately. DO NOT APPROACH TAs AS THEY ARE NOT AUTHORIZED TO GIVE THESE CLARIFICATIONS.

FRONT VIEW SIDE VIEW

TOP VIEW ISOMETRIC

VIEW


2/228


3/228


4/228


5/228


6/228


7/228


8/228


9/228


10/228


11/228


12/228


13/228


14/228


15/228


16/228


17/228


18/228


19/228


20/228


21/228


22/228


23/228


24/228


25/228


26/228


27/228


28/228

Q.27


29/228


30/228


31/228


32/228


33/228


34/228


35/228


36/228


37/228


38/228


39/228


40/228


41/228


42/228


43/228


44/228


45/228


46/228


47/228


48/228


49/228


50/228


51/228


52/228


53/228


54/228


55/228


56/228


57/228


58/228


59/228


60/228


61/228


62/228


63/228


64/228


65/228


66/228


67/228


68/228


69/228


70/228


71/228


72/228


73/228


74/228


75/228


76/228


77/228


78/228


79/228


80/228


81/228


82/228


83/228


84/228


85/228


86/228


87/228


88/228


89/228


90/228


91/228


92/228


93/228


94/228


95/228


96/228


97/228


98/228


99/228


100/228


101/228


102/228


103/228


104/228


105/228


106/228


107/228


108/228


109/228


110/228


111/228


112/228


113/228


114/228


115/228


116/228


117/228


118/228


119/228


120/228


121/228


122/228


123/228


124/228


125/228


126/228


127/228


128/228


129/228


130/228


131/228


132/228


133/228


134/228


135/228


136/228


137/228


138/228


139/228


140/228


141/228


142/228


143/228


144/228


145/228


146/228


147/228


148/228


149/228


150/228


151/228


152/228


153/228


154/228


155/228


156/228


157/228


158/228


159/228

Q.

15


160/228


161/228


162/228


163/228


164/228


165/228


166/228

Q.1


167/228


168/228


169/228


170/228


171/228


172/228


173/228


174/228


175/228


176/228


177/228


178/228


179/228


180/228


181/228


182/228


183/228


184/228


185/228


186/228


187/228


188/228


189/228


190/228


191/228


192/228


193/228


194/228


195/228


196/228


197/228


198/228


199/228


200/228


201/228


202/228


203/228


204/228


205/228


206/228


207/228


208/228


209/228


210/228


211/228


212/228


213/228


214/228

Q.213


215/228

Q.214


216/228

Q.215


217/228

Q.216


218/228

Q.217


219/228

Q.218


220/228

Q.219


221/228

Q.220


222/228

Q.221


223/228

Q.222


224/228

Q.223


225/228

Q.224


226/228

Q.225


227/228

Q.226


228/228

Documents

Sheet CAD02-SolidWorks 3D Modeling.pdf