ShopNotes Issue 121

7/14/2019 ShopNotes Issue 121

http://slidepdf.com/reader/full/shopnotes-issue-121 1/55







































































































Materials List

ShopNotes No. 121 Page 1 of 1 ©2012 August Home Publishing. All rights reserved.

wall-mounted

Tool Shelf

Cutting Diagram

NOTE: CUT SPACERS (I)TO LENGTH

AFTER SHAPING

AA

#/4" x 6" - 60" (2.5 Bd. Ft.)

!/2" x 6" - 96" (4.0 Sq. Ft.)

B B CC DD

E

G H

!/2" x 5" - 48" (1.7 Sq. Ft.)

!/4" x 24" - 48" PLYWOOD

F

N N N N

JJ J K K KK

LL L L MM M M

J

I

A Ends (2) 3/4 x 6 - 14

B Top Shelf/Bottom (2) 1/2 x 53/4 - 24

C Dividers (2) 1/2 x 53/4 - 43/4

D Drawer Shelves (2) 1/2 x 53/4 - 51/8

E Cleat (1) 3/4 x 21/4 - 243/4

F Back (1) 121/4 x 243/4 - 1/4 Ply.G Rear Tool Rail (1) 1/2 x 1 - 233/4

H Front Tool Rail (1) 1/2 x 1/2 - 233/4

I Spacers (12) 1/2 x 1/2 - 1

J Small Drawer Sides (4) 1/2 x 17/16 - 51/4

K Small Drawer Fronts/Backs (4) 1/2 x 17/16 - 413/16

L Large Drawer Sides (4) 1/2 x 27/16 - 51/4

M Large Drawer Fronts/Backs (4) 1/2 x 27/16 - 413/16

N Drawer Bottoms (4) 45/16 x 51/4 - 1/4 Ply.

• (12) #6 x 11/2" Fh Woodscrews

• (3) #8 x 2" Fh Woodscrews• (4) #8 x 3/4" Fh Woodscrews

• (12) 3/8"-dia. Wood Plugs

• (4) 1/2"-dia. Brass Knobs (Bronze Finish)




Save time andeffort with these

patterns formaking the steel

sides and thehardwood toteand cheeks.

infill

Smoothing Plane

All o the parts or the infll

smoothing plane rom ShopNotes121 eature curves or irregular

shapes. You can eliminate quite a bit o layout time by using the ull-

size patterns on these two pages.

Side Pattern. To make the steel

sides, I printed two copies o thepattern below. One is used to

make a hardboard template. Andthe other is used as a guide or

drilling all the holes.

Rear Infll. You’ll only need one

pattern to cut out and shape thetote. When making the cheeks,

keep in mind that they end up asmirror images. So the pattern isonly used to cut the fnal shape.

SIDE PATTERN (SHOWN ACTUAL SIZE)

NOTE: ALL HOLESARE %/32" DIA.

FACTORY EDGES

1 SQUARE = !/4"




TOTE PATTERN (SHOWN ACTUAL SIZE)

WASTE

NOTE: CUT FINALBED ANGLE

AFTER GLUINGCHEEKS TO TOTE

TOTE

1 SQUARE = !/4"

CHEEK PATTERN (SHOWN ACTUAL SIZE)

WASTE

CHEEK

1 SQUARE = !/4"



Documents

ShopNotes Issue 121