SIGMA ELECTRONICA LTDA. Sudamérica · 2016-11-05 · Quectel GSM Module Family ... QServer_V1.0 … M95 Datasheet M10_GSM_Module_Specification M95_HD_V1.1 M95_ATC_V1.1 ... specification

Estimados clientes y amigos: A continuación les presentamos nuestro Boletín #38. Este es un documento informativo acerca de los productos Quectel que comercializamos. Recuerden que pueden hacer sus compras en línea desde cualquier lugar del país, con varias formas de pago (Tarjeta de Crédito, Tarjeta Debito, Pago referenciado y en Efectivo) buscando la facilidad para cada uno de ustedes.

SIGMA ELECTRONICA LTDA. Av. Carrera 24 No.61D-65. PBX 3482059 - FAX 3466185. Bogotá - Colombia – Sudamérica

Horario de Atención: Lunes a Viernes 8:30AM-12:30PM y 1:30PM-5:30PM, Sábados de 10AM a 1PM

www.quectel.com

Agenda

GSM ModulesGSM module portfolio and roadmapQuectel documents structureM95 presentationEasy to designApplications Hardware Design

GPS ModulesGPS module Portfolio and roadmapFeatures comparisonL70 presentation

Quectel’s AdvantagesPlatformTechnical Support

www.quectel.com

Agenda




www.quectel.com

GSM module PortfolioM10 M80 M95

Picture

Summary 64-pin SMD Quad-Band110-pin SMDQuad-Band with Camera interface

42-pin SMD Quad-Band

Operation Temperature -40 ~ +80 -45 ~ +85 -40 ~ +85

Dimensions (mm) 29 × 29 × 3.6 25 × 23 × 2.6 19.9 × 23.6 × 2.65

Weight (g) 6 3.3 3

Network Protocols

PPP, TCP/UDP, HTTP, FTP, MMS, SMTP

PPP, TCP/UDP, HTTP, FTP, MMS, SMTP

PPP, TCP/UDP, HTTP, FTP

Features SMS, Echo Arithmetic, CSD, DTMF

SMS, Echo Arithmetic, CSD, DTMF

SMS, Echo Arithmetic, CSD

Certifications CE/ GCF/ FCC/ PTCRB/IC/ANATEL / TELCEL/ICASA /NCC

CE/ICASA/ ANATEL

CE/FCC/IC/NCCANATEL / TELCEL

• SMS• Voice Call• Data Call• PPP• TCP/UDP• MMS• FTP• SMTP• HTTP

• DTMF Decoding• Jamming Detection• NITZ • NTP • GSM Location • Dual UART • TTS • FOTA • Camera

www.quectel.com

DTMF Decoding

Dual-tone multi-frequency signaling (DTMF) is used for telecommunication signaling over analog telephone lines in the voice-frequency band between telephone handsets and other communications devices and the switching center.

www.quectel.com

DTMF Decoding and encoding

www.quectel.com

Security Applications protocol

www.quectel.com

A jammers blocks cell phone use by sending out radio waves along thesame frequencies that cellular phones use.This causes enough interference with the communication between cellphones and towers to render the phones unusable. On most retail phones,the network would simply appear out of range.

Most cell phones use different bands to send and receive communicationsfrom towersJammers can work by either disrupting phone to tower frequencies or towerto phone frequencies. Smaller handheld models block all bands from800 MHz to 1900 MHz within a 9 meters range.

The embedded Jamming Detect & Report feature allowsall our GSM modules to detect the presence of adisturbing device such as a phone jammer and gives ahardware and software indication of the event.

Jamming Detection

www.quectel.com

Network Identity and Time Zone is often used to automatically update the system clock of mobile phones and devices through GSM network.

NITZ

www.quectel.com

Network Time Protocol (NTP) is a networking protocol for synchronizing the clocks of computer systems over packet-switched, variable-latency data networks.

Network Access Point of ChinaAT+QNTP=“210.72.145.44”,123

QNTP:0

AT+CCLK to set time.

Network Access Point of Argentina: 200.49.40.1: CNAME:tick.nap.com.ar port:123200.49.32.1: CNAME:tock.nap.com.ar port:123

NTP

www.quectel.com

GSM Location GSM Mobile Station Locating

www.quectel.com

Dual UART

UART1

UART3

AT commands / Data transmit in transparence mode

AT commands only

www.quectel.com

TTS Speech synthesis

www.quectel.com

FOTA Firmware Over-the-Air

GSM/GPRS

www.quectel.com

GSM module portfolio and roadmap

2009 2010 2011 2012Q1 Q2 Q3 Q4

Value

Evolution

Advanced

M10 MP

M80 MP

Full functionalityLCC package

M95 MPData + AudioLCC packageSmallest

Leading functionalityLGA package

www.quectel.com

Agenda




www.quectel.com

Quectel document structure

CommonDatasheetQuectel GSM Module FamilyApplication Notes GSM_TCPIP_Recommended_ProcessGSM_ATC_AN_V1.00GSM_DTMF_AN_V1.1GSM_FTP_ATCGSM_SMTP_ATC_V1.1GSM_HTTP_ATC_V1.1GSM_SMS_ANGSM_MMS_ATC_V1.1GSM_Jamming_Detection_AN_V1.0GSM_Location_ATC_V1.2RF LAYOUT_AN_V1.0…AN_SpecialFw_Update_Protocol_ANFw_Update_Protocol_AN_V1 3GSM_eCall_AN_V1.1…Development kitQCOMQServer_V1.0…

M95DatasheetM10_GSM_Module_SpecificationM95_HD_V1.1M95_ATC_V1.1Development kitM95 Reference DesignM10-EVB_V2.01_SCHM95_Part&Decal…CertificationM95_CE_CertificateM95_FCC_CertificateM95_IC_CertificateM95_ICASA_CertificateM95_NCC_CertificateM95_RF_Test_ReportM95_EMC_Test_ReportM95_Test_Report…

www.quectel.com

Agenda




www.quectel.com

Ultra Small and Thin19.9mm x 23.6mm x 2.65 mm

High Data Speed

GPRS Multi-slot Class 12

Wide Working

Temperature Range

-40 to +85

Extremely Low Standby

Current Consumption

0.9mA @ DRX=5

M95 Highlights

Quad-band

850/900/1800/1900MHz

Humanization Design

Multi Fool-proof / Flexible layout

www.quectel.com

Reliable network protocolSteady flash protected mechanismSuperior audio algorithms

Software Advantages

QualityGuarantee

InternetService

TCP/IPUDPFTPHTTP

www.quectel.com

M95 Target Applications

VTS

Industrial PDA

Personal Tracking

Wireless POS

Smart Metering

www.quectel.com

Products Comparison

Product Features M95 C-company BXS2 T-company XE865

Size（mm） 19.9×23.6×2.65 18.8×26.7×2.7 22×22×3.0

Package LCC, easier soldering and production LGA package BGA package, difficult

soldering Current consumption

Sleep mode

0.9mA @ DRX=50.7mA @ DRX=9

1.5mA @ DRX=51.2mA @ DRX=9 1.5mA@ DRX=9

GPRSClass 12: max. 85.6 kbps(uplink & downlink)

Class 10: max. 42.8 kbps(uplink), 85.6kbps(downlink)

Class 10: max. 42.8 kbps(uplink & downlink)

Sensitivity -108.5dBm -107dBm

GSM850 & GSM900：-107dBmDCS1800 & PCS1900：-106dBm

Switch-off normal method

By “PWRKEY” or ATcommand Only AT command Only AT command

Audio interface 2 channel 1channel 1channel

www.quectel.com

Agenda




www.quectel.com

Easy to design

Technical Materials Package• Hardware, software,

specification• Application notes package• Debug tool, download tool, test

tool, EVB package

• Approvals & test report package

M95 EVB KIT

Development Tool• Interfaces

RS-232 interface Power supplyAntenna interfaceDebug UART interfaceHandset interfaceEarphone interface

• FeaturesNetwork status LEDPower keyEmergency off key

www.quectel.com

Easy to design

GSM_ATC_AN.pdfQuick guides to lead you evaluate AT functions on Evaluation Kit step by step.

www.quectel.com

Easy to design

Qcom tool for serial port communicationScript file can be saved and loaded for operating conveniently.

www.quectel.com

Agenda




www.quectel.com

TCPIP

How to establish TCP connection1)GSM_TCPIP_Recommended_Process.pdf 2) GSM_TCPIP_AN_V1.1.pdf

HOST CPU GSM ModuleAT+QICSGP=1,”apn”Set APN

AT+QIOPEN=“TCP”,”116.226.39.202”,”7007”Open TCP connection to server

Connect toTCP server. IP address: 116.226.39.202Port: 7007

CONNECT OK

AT+QISEND> TEST<ctrl+Z>

AT+QISACK

Send “TEST” to server

SEND OK

Query ACK

Send data to server

+QISACK: X,X,0

www.quectel.com

TCPIP

AT+IPR=115200&W // Fixed band rate as 115200bps.OK

AT+CPIN? //Make sure the SIM PIN is unlocked.+CPIN:READY //It shows SIM PIN is unlocked and ready

OK

AT+CREG? //Make sure the network is registered successfully+CREG: 0,1

AT+QIFGCNT=0 //Set the Context 0 as the foreground context. //Then all the following operations are aimed at Context 0.

OK

AT+QICSGP=1,"CMNET" //Set APN for the current context. OK

AT+QIOPEN="TCP","116.226.39.202","7007" //Visit the remote TCP server: 116.226.39.202:7007OK

CONNECT OK // Successfully connect to the remote TCP server

AT+QISEND //Ready to send dataTEST<Ctrl+Z>

SEND OK

AT+QISACK // Check if data has been sent successfully by querying the data information.+QISACK: 4, 4, 0OK

www.quectel.com

Easy to design

Qserver tool is used to create a TCPIP server.

www.quectel.com

Easy to design

Send SMS in text mode AT+CMGF=1 // <mode>=1 ,set text mode OK

AT+CSCS="GSM" // <chset>="GSM" , set character set to "GSM"OK

AT+CMGS="15021012496" // Send text SMS> Hello,Quectel! // Input the content of SMS

+CMGS: 26OK

OK

Send SMS in PDU modeAT+CMGF=0 // <mode>=0, set PDU mode OK

AT+CMGS=43 // Send PDU SMS >0011000D91685120012194F60008011C00480065006C006C006F002C005100750065006300740065006C0021

//The destination number is 8615021012496,the content of SMS is "Hello,Quectel!"+CMGS: 254 OK

www.quectel.com

Agenda




www.quectel.com

Hardware Architecture

www.quectel.com

Power supply

The voltage converter should provide current at least 1.6A

www.quectel.com

Power supply

Multislot class

Downlink slots Uplink slots Active slots

8 4 1 59 3 2 5

10 4 2 511 4 3 512 4 4 5

www.quectel.com

Power supply

Hardware design requirements for power supply:

1. Input voltage: 3.3~4.6V typical: 4.0 V 2. Regulator Current output: up to 1.6A3. Voltage Ripple: <=400mV4. The width of VBAT trace: > 2mm,

Module’s GND trace, as wider and shorter as possible

www.quectel.com

Power ON/OFF

Turn on the module using driving circuit

Reference circuit for EMERG_OFF by using driving circuit

www.quectel.com

Power ON/OFF

Timing for Turning on system

www.quectel.com

Power ON/OFF

Timing of Turning of the module

www.quectel.com

SIM interface

Reference circuit of the 6 pins SIM card

www.quectel.com

SIM interface

Notice for SIM interface Design

Place the SIM card holder close to module as close as possible. Ensure the trace length of SIM signals keeps less than 200mm.

1) Keep the SIM signals far away from VBAT power and RF trace.

2) The width of SIM_VDD and SIM_GND trace is not less than 0.5mm. Place a bypass capacitor close to SIM card power pin. The value of capacitor is less than 1uF.

3) To avoid possible cross-talk from the SIM_CLK signal to the SIM_DATA signal be careful that both traces are not placed closely next to each other. The traces of SIM_CLK, SIM_DATA and SIM_RST are recommended to be around with GND independently.

4) All signals of SIM interface should be protected against ESD with a TVS diode array. It is recommended to add TVS diode such as WILL (http://www.willsemi.com) ESDA6V8AV6. The parasitic capacitance of TVS diode is less than 50pF.

5) The 22Ω resistors should be added in series between the module and the SIM card so as to suppress the EMI spurious transmission and enhance the ESD protection. All the peripheral components are recommended to place near the SIM card holder.

www.quectel.com

SIM interface

Signal of SIM_VDD

www.quectel.com

UART interface

MCU/ARM MODULE

/TXD

/RXD TXDRXD

RTSCTSDTR

RI

/RTS/CTSGPIO

EINT

GPIO DCD

1K

1K

1K

1K

1K

1K

1K

5.6K 5.6K5.6K

Voltage level: 3.3V

The reference design of 3.3V level match is shown as above.

Note: When the peripheral MCU/ARM system is 3V, the divider resistor should be changed from 5.6K to 10K.

www.quectel.com

UART interface

MCU/ARM

/TXD

/RXD

1K

VDD_EXT

4.7k

VCC_MCU4.7k

4.7k

4.7k

VDD_EXT

TXD

RXD

RTS

CTS

DTR

RI

/RTS

/CTS

Voltage level: 5V

GPIO STATUS

MODULE

GPIO

EINT

VCC_MCU

5V level match circuit

www.quectel.com

RF interface

A PI match circuit is recommended to be added between the RF connector and RF_ANT PIN,For RF layout, please refer to RF LAYOUT_AN_V1.0 document.

RF_ANT0R

MODULENMNM

www.quectel.com

Agenda




www.quectel.com

GPS Roadmap

L10

17*22.4*3MT3329High sensitivity

2012 Q22011 H2

28*16*3.0Integrated GPS antenna High sensitivity

L50 ROM1.3

Ultra-slim size 9*9*1.6SiRF Star IVCGEE

L30 ROM1.3

CGEE12.2*16*2.4SiRF Star IVHigh sensitivity

L20 ROM1.3

2012 Q12011 Before 2011 H1

Mass production

In plan

STA8088FG17*22.4*2.8GPS/GLONASSAbundant interface

2012 Q3

MT33399.7*10.1*2.5EASY，EPOLow power consumption Extended working voltage range

Stop production

L16

L70

2012 Q3

www.quectel.com

Agenda




www.quectel.com

Introduction to GPS modules

1. L10 GPS module L10 GPS module is based on MT3329 GPS Engine from MTK，fully compatible with U-blox’s LEA series.

Features of L10 GPS Module:

1. High sensitivity：-165dBm @ Tracking Mode; -148dBm@acquisition Mode

2. Low power consumption : 38mA@Tracking Mode

3. Optional data update frequency for UART: 1Hz and 5Hz

4. Full ESD protection on all pins

5. Internal integrated LNA

6. Antenna detection and detection function for active antenna and short circuit

7. EPO AGPS function based on Server *

8. Extended working voltage range: 3.0V~4.3V

2. L20 GPS Module L20 GPS module is based on SiRFstarIV GPS Engine from CSR，fully compatible with NEO series of U-blox

Features of L20 GPS Module:

1. High sensitivity ：-163dBm @ Tracking Mode; -148dBm@acquisition Mode

2. Multiple power saving mode ：ATP、PTF、Hibernate

3. AGPS function ——CGEE, up to 3 days

4. Anti-jamming function ：Removes in-band Jammers up to 80dB-Hz; Tracks up to 8CW jammers

5. Internal integrated LNA

www.quectel.com

INTRODUCTION TO GPS MODULES

6. ROM2.2 version supports MEMS devices such as accelerometer sensor and compass(magnetic sensor), which can improve positioning accuracy


3. L30 GPS module L30 GPS module is based on SiRFstarIV GPS Engine from CSR

Features of L30 module

1. Dimensions：9*9*1.6m

2. High sensitivity：-163dBm@Tracking Mode; -148dBm@acquisition Mode

3. Multiple power saving mode ：ATP、PTF、Hibernate

4. AGPS function ——CGEE：

5. Anti-jamming function ：Removes in-band Jammers up to 80dB-Hz; Tracks up to 8CW jammer

6. ROM2.2 version supports MEMS devices such as accelerometer sensor and compass(magnetic sensor), which can improve positioning accuracy.

4. L50 GPS module L50 GPS module is based on SiRFstarIV GPS engine from CSR

Features of L50 module

1. Embedded 15*15 GPS patch antenna

2. High sensitivity ：-163dBm @ Tracking Mode; -148dBm@acquisition Mode

3. Low power consumption ：38mA@Tracking Mode

4. AGPS function ——CGEE：

www.quectel.com

5. Anti-jamming function ：Removes in-band Jammers up to 80dB-Hz; Tracks up to 8CW jammer

6. ROM2.2 version supports MEMS devices such as accelerometer sensor and compass(magnetic sensor), , which can improve positioning accuracy

5. L16 GPS/GLONASS module Based on the STMicroelectronics Teseo II positioning engine, L16 is a single receiver module integrated with

GLONASS and GPS system

Features of L16 GPS/GLONASS/Gallieo/QZSS module

1. STMicroelectronics TeseoII single chip solution

2. Simultaneously use GLONASS and GPS system

3. 32 tracking channels and 2 fast acquisition channels

4. Highly dynamic indoor sensitivity of –162dBm in tracking mode ²

5. Higher autonomous acquisition mode sensitivity, -148dBm

6. Full ESD protection on all pins

7. High performance ARM946 MCU (up to 208MHz)

8. In-Package SQI 16Mbits Flash Memory

9. Superior performance even in the toughest urban environments

10. Up to 5Hz update rate

11. Support ST-AGPS self Assisted-GPS technology, up to 5 days

12. Support DGPS: SBAS(WAAS, EGNONS, MSAS,GAGAN)


www.quectel.com

6. L70 GPS

L70 GPS module is based on the latest GPS chipset MT3339 from MTK, compatible with MAX-6 series of Ublox.

Features of L70 module:

1. Highly compact size: 9.7*10.1*2.5mm

2. High sensitivity ：-163dBm@Tracking mode，-148dBm@Acquisition mode

3. Low power consumption ：22mA@Tracking mode，25mA@Acquisition mode

4. Multiple power saving mode ：Standby mode，Backup mode，Periodic mode，AlwaysLocate mode

5. Up to 5Hz update rate

6. Support self-AGPS without external memory


8. EPO AGPS based on server *

9. Anti-Jamming: AIC （Active interference cancellation）

10. DGPS


www.quectel.com

Agenda




www.quectel.com

Highlights

EASY™Advanced AGPS technology

without external memory

Highest Sensitivity-163dBm@Tracking mode

-148dBm@Cold Start

AlwaysLocate™An intelligent controller of power consumption

Extremely Compact Size 10.1 x 9.7 x 2.5 mm

MT3339 Single Chip Solution66 acquisition channels22 tracking channels

Ultra Low Power Consumption22mA@ Tracking mode 25mA @Acquisition mode

Anti-JammingMulti-tone Active

Interference Canceller

LOCUSInnate logger solution without host and

external flash

www.quectel.com

Target Applications

Portable Devices

Vehicle Management

Asset Tracking

Security System

Connected PND

GIS Application

Industrial PDA

www.quectel.com

Self-AGPS EASY Technology(1)

EASY™ is the abbreviation for Embedded Assist System for quick positioning.With EASY™

technology, the GPS engine can calculate and predict automatically singleephemeris ( up to 3 days) when the power is on, and then save the predictinformation onto the memory. So the GPS engine can use the information forpositioning later if there are not enough information received from the satellites.

This function will be helpful for positioning and TTFF improvement under indoor orurban conditions.

www.quectel.com

With EASY™ technology, L70 accelerates TTFF obviously.

Self-AGPS EASY Technology(2)

Test Condition TTFF without EASY TTFF with EASY

Under GPS signal Generator, conductive power level -

130dBm

Cold Start <35s <15s

Warm Start <30s <5 s

TTFF Comparison

www.quectel.com

Periodic Standby Mode

Controlling power on/off Standby Mode periodically can reduce power consumption.

On/Off time can be configured by using PMTK command.

For example, On for 3 seconds, Off for 12 seconds

www.quectel.com

AlwaysLocate Technology

AlwaysLocate™ is an intelligent controller of periodic mode.

L70 can adaptively adjust the on/off time to achieve balance between positioning accuracy and power consumption according to the environmental and motion conditions.

www.quectel.com

L70 vs. ucompany NEX-6Q(1)

Product Features L70 Ucompany NEX-6Q

Power supply 2.8V~4.3V 2.7V~3.6V

Power consumption

Acquisition mode 25mA @ 3.3V117mW @ 3.0V Typical

Tracking mode 22mA @ 3.3V

Sensitivity

Cold start -148dBm -148dBm

Hot start -160dBm -157dBm

Tracking -163dBm -162dBm

Re-acquisition -160dBm -160dBm

TTFF@-130dBm

Hot start <1s 1s

Warm start <5s (EASY™ ) 26s

Cold start <15s (EASY™ ) 26s

Position accuracy 2.5m CEP 2.5m CEPTiming accuracy 1PPS 10ns 30ns

Data update rate Up to 10Hz Up to 5Hz

Specifications Comparison

www.quectel.com

Ucompany NEX-6Q

L70

When driving across high buildings and making a turn, L70 module can still capture the accurate tracking data.


Tracking Comparison

www.quectel.com

When driving back and forth under the overpass, L70 module has small drift.


Tracking Comparison

Ucompany NEX-6Q

L70

www.quectel.com

When driving into a channel, the GPS signal becomes weak. L70 can still fix positionfor a while.


Tracking Comparison

Ucompany NEX-6Q

L70

www.quectel.com

Q&A

The End

Documents

SIGMA ELECTRONICA LTDA. Sudamérica · 2016-11-05 · Quectel GSM Module Family ... QServer_V1.0 … M95 Datasheet M10_GSM_Module_Specification M95_HD_V1.1 M95_ATC_V1.1 ... specification