WARNING

You must read and understand these instructions before using the

Drum Foundry Snare Bed Cutter. Failure to use this tool in the prescribed manner

can result in injury.

Always wear eye and ear protection when working with power tools.

Only for use by experienced router operators.

SIDE SUPPORTS TEMPLATEATTACHMENTSCREWS

TEMPLATE ID

HANDLE SLIDING SHELL CLAMPLOCKING KNOB

SHELL DEPTH RULERSQUARING GUIDE

JIG BASE

SNARE BED TEMPLATE

SHELL DEPTH INDICATOR ARROW

The Drum Foundry Snare Bed Cutter

Part Descriptions

Sta

nd

ard

Sn

are

Te

mp

late

Sh

ap

es

Prin

ted

to a

ctua

l siz

e. T

he m

easu

rem

ents

indi

cate

the

pre

set

dim

ensi

ons

of th

e te

mpl

ate

whe

n th

e in

dica

tor

arro

w is

set

to th

e ex

act s

hell

dept

h. T

empl

ates

may

be

used

to m

ake

beds

slig

htl

y de

eper

/wid

er o

r sh

allo

wer

/nar

row

er. S

ee d

irect

ions

for

com

plet

e in

form

atio

n.

Tem

pla

te B

- S

mo

oth

arc

, 6

inch

es w

ide

, 1

/8”

de

ep

Tem

pla

te A

- S

mo

oth

arc

, 8

inch

es w

ide

, 3

/32

” d

ee

p

Tem

pla

te C

- F

lat sh

ap

e, 3

in

ch

es

wid

e o

n fla

t p

art

, 5

/8”

wid

e r

am

ps o

n e

nd

s, 1

/8”

de

ep

Requirements for using the DF Snare Bed CutterYou must have a router with a ½" diameter collet that is mounted in a router table. You must be able to insert the router bit into the collet at least 1 inch and still be able to raise the bit so the bearing is above the router table. Do not use any other bit than the included bit. Replacement bits can be purchased from Drum Foundry.

Setting up the router bit in the router table

1. Before inserting the router bit into the collet, remove the collet and clean all dirt and dust from the collet and the router.

2. Insert the router bit with at least 1 inch of shank in the collet. Do not “bottom out” this or any other router bit in a router. The collet pulls down on the bit to tighten it, and if the bit is already at the bottom of the collet then there is danger of the bit becoming loose.

3. Mount the router in the table so the bearing on the router bit is in full contact with the template.

Bearing contacts template

Setting up the shell in the jig and using the standard templates

1. We suggest that your bearing edges are already cut on your shell before you cut the snare bed. Mark the exact center of your snare beds on both sides.

2. Measure the exact height of your shell. Set the arrow on the sliding clamp to the height of your shell and tighten the locking knob. Matching up these two measurements will cut the snare bed to the preset width and depth of the template.

3. Loosen the knobs on the side supports and slide toward the outer edges of the base.

Set arrow toshell depth

Tightenknob

4. Place the shell under the clamp and push the edge fully against the squaring guide. Match up the center mark on your shell with the center mark on the template. Clamp down the shell and check that the bearing edge is flush against the squaring guide. Excessive clamp tension is not necessary, and may overflex and distort the base of the jig.

5. Push the side supports firmly into the shell so the rubber bumper makes full contact with the shell, and tighten the side support locking knobs.

IMPORTANT! Before cutting the snare bed, double check that

all knobs are secure and the shell is stable.

4. Start the router motor with the jig at a safe distance away from the blades. The base is marked with a “BEGIN” and “END”. This will ensure that you are always cutting in the correct and safe direction in relation to the router bit rotation.

DO NOT use a climb cut by starting at the side marked “END”! You will not achieve any better results by doing so, and it is much more dangerous.

Check that you have set the measurement correctly and the shell is not too far out over the template. The router bit bearing must contact template before the cutting edges touch the shell.

5. Begin the cut by sliding the jig against the router bit at the “BEGIN” end of the template. Slowly slide the jig from right to left and cut the snare bed shape. It should only take one pass to cut the snare bed shape.

6. The snare bed shape is now cut, and you may finish it by rounding over the sharp edges with a file or sandpaper.

If you have any questions about the use of your Snare Bed Cutter, please call us at 616-879-0429. You may also email questions to info@drumfoundry.com.

Drum Foundry LLC11114 James St.

Zeeland, MI 49464

www.drumfoundry.com

Page 1Page 2Page 3Page 4Page 5Page 6Page 7Page 8