161
CCD-TR913E/TR950E RMT-708 SERVICE MANUAL VIDEO CAMERA RECORDER MICROFILM B501 MECHANISM Photo: CCD-TR950E SPECIFICATIONS For MECHANISM ADJUSTMENT, refer to the “8mm Video MECHANICAL ADJUSTMENT MANUAL ” (9-973-801-11). AEP Model North European Model East European Model Russian Model CCD-TR913E/TR950E UK Model CCD-TR913E Ver 1.0 1999.02

Sony Ccd Tr913e

Embed Size (px)

Citation preview

CCD-TR913E/TR950ESERVICE MANUALVer 1.0 1999.02

RMT-708

AEP Model North European Model East European Model Russian ModelCCD-TR913E/TR950E

UK ModelCCD-TR913E

Photo: CCD-TR950E

B501 MECHANISM

For MECHANISM ADJUSTMENT, refer to the 8mm Video MECHANICAL ADJUSTMENT MANUAL (9-973-801-11).

SPECIFICATIONS

VIDEO CAMERA RECORDERMICROFILM

Table for difference of function Model Destination Lens Color EVF B/W EVF Optical Digital CCD-TR913E CCD-TR950E AEP1, AEP2, UK, NE, AEP, NE, EE, RU EE, RU 20 80 (Note) ! 20 80 (Note) !

Remark

: With VF-126 board : With VF-129 boardAbbreviation NE : North European Model EE : East European Model RU : Russian Model

Note : AEP1, EE, NE, RU model is 360.

Supplied accessories

SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

SAFETY CHECK-OUTAfter correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. 4. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. 5. Check the B+ voltage to see it is at the values specified. 6. Flexible Circuit Board Repairing Keep the temperature of the soldering iron around 270C during repairing. Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). Be careful not to apply force on the conductor when soldering or unsoldering.

2. 3.

2

TABLE OF CONTENTS SERVICE NOTE1. 2. POWER SUPPLY DURING REPAIRS 6 TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT) 6 2-5. 2-6. 2-7. 2-8. Lens Block 2-6 Mechanism Deck, VC-214, DD-117 Boards 2-7 Video Light 2-9 CF-58 Board (TR913E) 2-9 CF-58 Board (TR950E) 2-9 2-9. How to Identify Drum and Note 2-10 2-10. Circuit Boards Location 2-11 2-11. Flexible Boards Location 2-12

SELF-DIAGNOSIS FUNCTION1. 2. 3. 3-1. 3-2. 3-3. 4. Self-diagnosis Function 7 Self-diagnosis Display 7 Service Mode Display 7 Display Method 7 Switching of Backup No. 7 End of Display 7 Self-diagnosis Code Table 8

3.3-1. 3-2. 3-3. 3-4. 3-5. 3-6. 3-7. 3-8. 3-9.

BLOCK DIAGRAMSOverall Block Diagram 3-1 Camera/Video Block Diagram 3-5 VTR/Camera Control Block Diagram 3-9 Servo Block Diagram 3-12 Mode Control Block Diagram 3-15 Audio Block Diagram 3-19 Color EVF Block Diagram (CCD-TR950E) 3-23 B/W EVF Block Diagram (CCD-TR913E) 3-27 Power Block Diagram 3-29

1.

GENERAL

Checking supplied accessories 1-1 Quick Start Guide 1-1 1. Connecting the mains lead 1-1 2. Inserting a cassette 1-1 3. Recording a picture 1-1 4. Monitoring the playback picture in the viewfinder 1-1 Getting Started 1-1 Using this manual 1-1 Step 1 Preparing the power supply 1-2 Step 2 Inserting a cassette 1-3 Recording Basics 1-4 Recording a picture 1-4 Checking the recording EDITSEARCH/Rec Review 1-6 Playback Basics 1-6 Connections for playback 1-6 Playing back a tape 1-7 Advanced Recording Operations 1-8 Photo recording 1-8 Using the wide mode 1-8 Using the fader function 1-9 Using special effects Picture effect 1-9 Using special effects Digital effect 1-10 Using the PROGRAM AE function 1-11 Adjusting the exposure manually 1-11 Focusing manually 1-12 Superimposing a title 1-12 Making your own titles 1-13 Using the built-in light 1-13 Advanced Playback Operations 1-14 Playing back a tape with digital effects 1-14 Editing on Other Equipment 1-14 Dubbing a tape 1-14 Customizing Your Camcorder 1-15 Changing the MENU settings 1-15 Resetting the date and time 1-16 Additional Information 1-17 Usable cassettes and playback modes 1-17 Changing the lithium battery in your camcorder 1-17 Troubleshooting 1-18 Self-diagnosis display 1-19 Warning indicators and messages 1-19 Using your camcorder abroad 1-19 Maintenance information and precautions 1-19 Quick Reference 1-21 Identifying the parts and controls 1-21 Quick function guide 1-23

4.

PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

2.2-1. 2-2. 2-3. 2-4.

DISASSEMBLYCabinet (R) Assembly (TR913E), (TR950E) 2-2 Mechanism Deck 2-3 Color EVF Block, VF-126 Board (TR950E) 2-4 B/W EVF Block, VF-129 Board (TR913E) 2-5

4-1. Frame Schematic Diagram-1 4-1 Frame Schematic Diagram-2 4-4 4-2. Printed Wiring Boards and Schematic Diagrams 4-7 CD-209 (CCD Imager) Printed Wiring Board and Schematic Diagram 4-8 VC-214 (Camera Processor, Y/C Processor, Focus/Zoom Motor Drive, REC/PB Head AMP, Video/Interface, IR, Mode Control, Servo, System Control,Audio Processor) Printed Wiring Board 4-11 VC-214 (Camera Processor)(1/10) Schematic Diagram ....................................... 4-17 VC-214 (Y/C Processor)(2/10) Schematic Diagram 4-19 VC-214 (Focus/Zoom Motor Drive)(3/10) Schematic Diagram 4-25 VC-214 (REC/PB Head AMP)(4/10) Schematic Diagram 4-27 VC-214 (Video/Interface)(5/10) Schematic Diagram 4-30 VC-214 (IR Transmitter)(6/10) Schematic Diagram 4-33 VC-214 (Mode Control)(7/10) Schematic Diagram 4-36 VC-214 (Servo)(8/10) Schematic Diagram 4-39 FP-249 (S/T Reel Sensor), FP-356 (Top Sensor), FP-355 (Tape LED) Flexible Board 4-42 VL-25 (Video Light) Printed Wiring Board 4-43 VC-214 (HI Control)(9/10) Schematic Diagram 4-44 VC-214 (Audio)(10/10) Schematic Diagram 4-47 SE-85 (Steady Shot), PJ-94 (AV IN/OUT) Printed Wiring Boards 4-50 SE-85 (Steady Shot), PJ-94 (AV IN/OUT) Schematic Diagrams 4-53 MA-353 (Stereo MIC AMP, Laser Link) Printed Wiring Board 4-55 MA-353 (Stereo MIC AMP, Laser Link) Schematic Diagram 4-57 VF-126 (Color EVF) Printed Wiring Board 4-61

3

VF-126 (Color EVF) Schematic Diagram 4-63 FK-8500, SS-8500 (Control Switch Block) Schematic Diagram 4-68 VF-129 (B/W EVF) Printed Wiring Board and Schematic Diagram ....................................... 4-69 CF-58 (User Control) Printed Wiring Board .................................... 4-72 CF-58 (User Control) Schematic Diagram 4-75 DD-117 (DC/DC Converter) Printed Wiring Board 4-79 DD-117 (DC/DC Converter) Schematic Diagram 4-81

5.

ADJUSTMENTS

5-1. CAMERA SECTION ADJUSTMENT 5-1 1-1. Preparations before Adjustment (Camera Section) 5-1 1-1-1. List of Service Tools 5-1 1-1-2. Adjusting Items When Replacing Main Parts 5-2 1-1-3. Preparations 5-3 1-1-4. Precaution 5-5 1. Setting the Switch 5-5 2. Order of Adjustments 5-5 3. Subjects 5-5 1-2. Initialization of D, E, F Page Data 5-6 1. Initializing the D, E, F Page Data 5-6 2. Modification of D, E, F Page Data 5-6 3. D Page Table 5-6 4. F Page Table 5-7 5. E Page Table 5-10 1-3. Camera System Adjustments 5-13 1. HALL Adjustment 5-13 2. Flange Back Adjustment 5-13 2-1. Flange Back Adjustment (1) 5-13 2-2. Flange Back Adjustment (2) 5-14 3. Flange Back Check 5-14 4. Picture Frame Setting 5-15 5. AGC Gain Calibration Adjustment 5-15 6. Color Reproduction Adjustment 5-16 7. IRIS IN/OUT Adjustment 5-16 8. MAX GAIN Adjustment 5-17 9. Auto White Balance Standard Data Input 5-17 10. Auto White Balance Adjustment 5-18 11. White Balance Check 5-19 12. Angular Velocity Sensor Sensitivity Preset and Steady Shot Check 5-20 1-4. Color Electronic Viewfinder System Adjustment (CCD-TR950E) 5-21 1. EVF Initial Data Input 5-21 2. VCO Adjustment (VF-126 board) 5-22 3. Bright Adjustment (VF-126 board) 5-22 4. Contrast Adjustment (VF-126 board) 5-23 5. Backlight Consumption Current Adjustment (VF-126 board) 5-23 6. White Balance Adjustment (VF-126 board) 5-24 1-5. Monochrome Electronic Viewfinder System Adjustment (CCD-TR913E) 5-25 1-5-1. Horizontal Slant Check 5-25 1-5-2. Centering Adjustment 5-25 1-5-3. Focus Adjustment 5-25 1-5-4. Aberration Adjustment 5-26 1-5-5. Horizontal Amplitude Adjustment (VF-129 board) 5-26 1-5-6. Vertical Amplitude Adjustment (VF-129 board) 5-27 1-5-7. Brightness Adjustment (VF-129 Board) 5-27

1-5-8. Horizontal Amplitude, Vertical Amplitude, Focus Check 5-27 5-2. MECHANISM SECTION ADJUSTMENT 5-28 2-1. Operating Without Cassette 5-28 2-2. Tape Path Adjustment 5-28 5-3. VIDEO SECTION ADJUSTMENT 5-29 3-1. Preparations Before Adjustments 5-29 3-1-1. Equipment to Required 5-29 3-1-2. Precautions on Adjusting 5-30 3-1-3. Adjusting Connectors 5-30 3-1-4. Connecting the Equipments 5-31 3-1-5. Alignment Tape 5-32 3-1-6. Output Level and Impedance 5-32 3-1-7. Recording Mode (Standard 8/Hi8) Switching 5-32 3-2. System Control System Adjustment 5-33 1. Initialization of D, E, F Page Data 5-33 2. Battery End Adjustment (VC-214 board) 5-33 3-3. Servo System Adjustments 5-34 1. CAP FG Offset Adjustment (VC-214 board) 5-34 2. Switching Position Adjustment (VC-214 board) 5-34 3-4. Video System Adjustments 5-35 1. 28 MHz Origin Oscillation Adjustment (VC-214 board) 5-35 2. AFC f0 Adjustment (VC-214 board) 5-35 3. Filter f0 Adjustment (VC-214 board) 5-36 4. Y OUT Level Adjustment (VC-214 board) 5-36 5. C OUT Level Adjustment (VC-214 board) 5-37 6. RP Filter f0 Adjustment (VC-214 board) 5-37 7. REC Y Current Adjustment (VC-214 board) 5-38 8. REC L Level Adjustment (VC-214 board) 5-39 9. REC C Current Adjustment (VC-214 board) 5-40 3-5. IR Transmitter Adjustments 5-41 1. IR Video Carrier Frequency Adjustment (VC-214 board) 5-41 2. IR Video Deviation Adjustment (VC-214 board) 5-41 3. IR Audio Deviation Adjustment (VC-214 board) 5-42 3-6. Audio System Adjustment 5-43 1. 1.5 MHz Deviation Adjustment (VC-214 board) 5-44 2. 1.7 MHz Deviation Adjustment (VC-214 board) 5-45 3. BPF f0 Adjustment (VC-214 board) 5-46 5-4. SERVICE MODE 5-47 4-1. Adjustment Remote Commander 5-47 1. Using the Adjustment Remote Commander 5-47 2. Precautions Upon Using the Adjustment Remote Commander 5-47 4-2. Data Process 5-48 4-3. Service Mode 5-49 1. Test Mode Setting 5-49 2. Emergency Memory Address 5-50 2-1. EMG Code (Emergency Code) 5-50 2-2. MSW Codes 5-51 3. Bit Value Discrimination 5-52 4. Input/Output Selection Check 5-52 5. LED, LCD (Display Window) Check 5-52 6. Record of Use Check 5-53 7. Switch Check (1) 5-53 8. Switch Check (2) 5-54 9. Headphone Jack Check 5-54

6.

REPAIR PARTS LIST

6-1. Exploded Views 6-1 6-1-1. Front Panel (D) Block and Battery Panel (P) Block Assembly 6-1 6-1-2. Cabinet (R) Block Assembly 6-2 6-1-3. Cabinet (L) Block and Main Boards Assembly 6-3 6-1-4. EVF Block Assembly 6-4

4

6-1-5. Zoom Lens (LSV-630A) 6-5 6-1-6. Cassette Compartment Assembly 6-6 6-1-7. LS Chassis Assembly 6-7 6-1-8. Mechanism Chassis Assembly 6-8 6-2. Electrical Parts List 6-9 * The color reproduction frame is shown on page 251.

5

SERVICE NOTE1. POWER SUPPLY DURING REPAIRSBattery switch

In this unit, about 10 seconds after power is supplied (8.4V) to the battery terminal using the service power cord (J-6082-223-A), the power is shut off so that the unit cannot operate. This following two methods are available to prevent this. Take note of which to use during repairs.

Method 1.Connect the servicing remote commander RM-95 (J-6082-053-B) to the LANC jack, and set the remote commander switch to the ADJ side.

Method 2.Press the battery switch of the battery terminal using adhesive tape, etc.

Method 3.Use the DC IN terminal. (Use the AC power adaptor.)

Battery terminal Battery terminal

DC IN terminal

Battery SIG terminal

2.1 2 3 4 5 6

TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT)Refer to 2-1. to remove the front panel assembly. Refer to 2-1. to remove the cabinet (R) assembly. Refer to 2-1. to remove the battery panel assembly. Refer to 2-1. to remove the cabinet (L) assembly. Disconnect CN901 of VC-214 board. Add +5V from the DC POWER SUPPLY and unload with a pressing the cassette lid.7 Pull the timing belt in the direction of arrow A with a pincette while pressing the cassette lid (take care not to damage) to adjust the bending of a tape.

Press the cassette lid to rise the cassette compartment

Pincette [DC power supply] (+5V)

Timing belt

8 Let go your hold the cassette lid and rise the cassette compartment to take out a cassette.

Loading motor

Disconnect CN901 of VC-214 board. Timing belt Adjust the bending of a tape

6

SELF-DIAGNOSIS FUNCTION1. Self-diagnosis Function 2. Self-diagnosis Display

When problems occur while the unit is operating, the self-diagnosis function starts working, and displays on the viewfinder or Display window what to do. This function consists of two display; selfdiagnosis display and service mode display. Details of the self-diagnosis functions are provided in the Instruction manual.ViewfinderC:31:11

When problems occur while the unit is operating, the counter of the viewfinder or Display window shows a 4-digit display consisting of an alphabet and numbers, which blinks at 3.2 Hz. This 5-character display indicates the repaired by:, block in which the problem occurred, and detailed code of the problem.

Display window

C : 3 1 : 11

Blinks at 3.2Hz

CRepaired by:

31Block

11Display windowDetailed Code

C : Corrected by customer H : Corrected by dealer E : Corrected by service engineer

Refer to page 8 and 9. Indicates the appropriate Self-diagnosis Code Table. step to be taken. E.g. 31 ....Reload the tape. 32 ....Turn on power again.

3.3-1.

Service Mode DisplayDisplay Method

The service mode display shows up to six self-diagnosis codes shown in the past.

While pressing the STOP key, set the switch from OFF to PLAYER, and continue pressing the STOP key for 5 seconds continuously. The service mode will be displayed, and the counter will show the backup No. and the 5-character self-diagnosis codes.Viewfinder[3] C : 3 1 : 1 1

Display window

3 C : 3 1 : 11

Lights up

[3]Backup No. Order of previous errors

C:31:11Self-diagnosis CodesControl dial

3-2.

Switching of Backup No.

By rotating the control dial, past self-diagnosis codes will be shown in order. The backup No. in the [] indicates the order in which the problem occurred. (If the number of problems which occurred is less than 6, only the number of problems which occurred will be shown.) [1] : Occurred first time [4] : Occurred fourth time [2] : Occurred second time [5] : Occurred fifth time [3] : Occurred third time [6] : Occurred the last time

3-3.

End of Display

Turning OFF the power supply will end the service mode display. Note: The self-diagnosis display data will be backed up by the coin-type lithium battery (CF-58 board BH001). When this coin-type lithium battery is disconnected, the self-diagnosis display data will be lost by initialization.

7

4.Repaired by:

Self-diagnosis Code TableSelf-diagnosis Code Block Detailed Function Code 2 2 2 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 1 2 3 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 2 0 0 0 1 1 2 2 2 2 3 3 4 4 4 4 4 1 1 2 2 2 2 3 3 4 4 4 4 4 0 0 0 0 1 0 1 2 3 0 1 0 1 2 3 4 0 1 0 1 2 3 0 1 0 1 2 3 4 Symptom/State Correction

C C C C C C C C C C C C C C C C C C C C C C C C C C C C C

Condensation. Video head is dirty. Non-standard battery is used. LOAD direction. Loading does not complete within specified time UNLOAD direction. Loading does not complete within specified time T reel side tape slacking when unloading. S reel side tape slacking when unloading. T reel fault. S reel fault. FG fault when starting capstan. FG fault during normal capstan operations. FG fault when starting drum. PG fault when starting drum. FG fault during normal drum operations. PG fault during normal drum operations. Phase fault during normal drum operations. LOAD direction loading motor timeout. UNLOAD direction loading motor time-out. T reel side tape slacking when unloading. S reel side tape slacking when unloading. T reel fault. S reel fault. FG fault when starting capstan. FG fault during normal capstan operations. FG fault when starting drum. PG fault when starting drum. FG fault during normal drum operations. PG fault during normal drum operations. Phase fault during normal drum operations.

Remove the cassette, and insert it again after one hour. Clean with the optional cleaning cassette. Use the InfoLITHIUM battery. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning.

8

Self-diagnosis CodeRepaired by:

Block Detailed Function Code

Symptom/State

Correction

E

6

1

0

0

Difficult to adjust focus (Cannot initialize focus.)

E

6

1

1

0

Zoom operations fault (Cannot initialize zoom lens.) Steady Shot correction function does not work well. (With pitch angular velocity sensor output stopped.) Steady Shot correction function does not work well. (With yaw angular velocity sensor output stopped.)

Inspect the lens block focus reset sensor (Pin ! of CN551 of VC214 board) when focusing is performed when the control dial is rotated in the focus manual mode and the focus motor drive circuit (IC552 of VC-214 board) when the focusing is not performed. Inspect the lens block zoom reset sensor (Pin ! of CN551 of VC214 board) when zooming is performed when the zoom lens is operated and the zoom motor drive circuit (IC552 of VC-214 board) when zooming is not performed. Inspect pitch angular velocity sensor (SE451 of SE-85 board) peripheral circuits. Inspect yaw angular velocity sensor (SE452 of SE-85 board) peripheral circuits.

E

6

2

0

0

E

6

2

0

1

9

SECTION 1 GENERAL

CCD-TR913E/TR950EThis section is extracted from instruction manual. (CCD-TR913E/TR950E model)

1-1

1-2

1-3

1-4

1-5

1-6

1-7

1-8

1-9

1-10

1-11

1-12

1-13

1-14

1-15

1-16

1-17

1-18

1-19

1-20

1-21

1-22

1-23E

SECTION 2 DISASSEMBLYThe following flow chart shows the disassembly procedure.

CCD-TR913E/TR950E

2-1. CABINET (R) ASSEMBLY (TR913E)(TR950E)

2-2 MECHANISM DECK (Note)

MECHANISM DECK check service position

Note : Use the parts only which can be removed easily from outside of the MECHANISM DECK. 2-3. COLOR EVF BLOCK, VF-126 board (TR950E) 2-4. B/W EVF BLOCK, VF-129 board (TR913E) COLOR EVF check service position B/W EVF check service position

CCD-TR913E/TR950E

How to remove the CRT UNIT

2-5. LENS BLOCK

LENS BLOCK check service position

2-6. MECHANISM DECK, VC-214 board, DD-117 board

MECHANISM DECK, VC-214 board, DD-117 board check service position

2-7. VIDEO LIGHT

2-8. CF-58 board (TR913E)(TR950E)

2-9. How to identify drum and note

2-1

NOTE: Follow the disassembly procedure in the numerical order given.

2-1. CABINET (R) ASSEMBLY (TR913E)

! Screw (M2 4), lock ace, p2 8 FP-43 flexible board (20P) 4 Screw (M2 4), lock ace, p2-21 VCard o B 4

! Two screws (M2 4), lock ace, p2 ! Screw (M2 4), lock ace, p2

1 Two screws (M2 4), lock ace, p2 3 Cabinet (L)

6 Screw (M2 4), lock ace, p2 2 Remove the claw ! Cabinet (R) assembly ! Remove the claws 0 Three screws (M2 4), lock ace, p2 7 Remove the claws Remove it while taking care as the FP-43 flexible board is connected. 5 Screw (M2 4), lock ace, p2

9 Panel (D) (front) assembly

CABINET (R) ASSEMBLY (TR950E)

! Screw (M2 4), lock ace, p2 8 FP-43 flexible board (20P) 4 Screw (M2 4), lock ace, p24 -21 VCard Bo

! Two screws (M2 4), lock ace, p2 ! Screw (M2 4), lock ace, p2

1 Two screws (M2 4), lock ace, p2 3 Cabinet (L)

6 Screw (M2 4), lock ace, p2 ! Cabinet (R) assembly ! Remove the claws 0 Three screws (M2 4), lock ace, p2 7 Remove the claws Remove it while taking care as the FP-43 flexible board is connected. 5 Screw (M2 4), lock ace, p2

2 Remove the claw

9 Panel (D) (front) assembly

2-2

2-2. MECHANISM DECK1 Two screws (M2 4), lock ace, p2 3 Screw (M2 4), lock ace, p2 2 Cassette lid assembly 5 Battery panel (P) assembly b

Remove it in the direction of the arrow b.

9 Jack cover

c

Remove it in the direction of the arrow a. Remove it gently as a thin flexible board is held by a claw. 6 Disengage the claw that fixes the flexible board.a

0 Cabinet (L) assembly

4 Screw(M2 4), lock ace, p2

c

VC

-21

48 Screw (M2 3)

7 Screw

! MD frame (B) ! Three screws (M2 3)

[MECHANISM DECK CHECK SERVICE POSITION] How to move up the cassette compartment manuallyPress the cassette compartment in the direction of the arrow e to move it up in the direction of the arrow f.eAC POWER ADAPTOR

AC IN Cabinet (L) assembly

DC IN LANC jack

f

Adjustment remote commander (RM-95) Battery panel (P) assembly Base (Use box or the like.)

FP-43 flexible board

Panel (D) (front) assembly

Cabinet (R) assembly

2-3

2-3. COLOR EVF BLOCK, VF-126 BOARD (TR950E)4 EVF block assembly 2 FFC-256 flexible flat cable (4P)

7 FP-47 flexible board ! Remove the claw 9 Slide fixed base(C)

3 Three tapping screws (B2 5) ! Two screws (M2 3) 1 FFC-236 flexible flat cable (50P) ! EVF cabinet (upper C) (92) ! EVF cabinet (rear C) (92) assembly 5 Screw (M2 3)

8 VF base(C)(92)

6 Harness guide ! VF-126 board

Craw

! Two screws (M2 3) ! Turn the lever in the direction of the arrow. ! Two tapping screws (B2 5)

Note : Be careful not to remove the spring when removing the item !.

[COLOR EVF CHECK SERVICE POSITION]Adjustment remote commander (RM-95)

LANC jack

CPC-7 jig (J-6082-382-A)

CPC-7 jig

DC IN

Contacting surface

FP-43 flexible board

AC POWER ADAPTOR

AC IN FP-47 flexible board

VF-126 board

VF lens assembly

Panel (D) (front) assembly Cabinet (R) assembly

2-4

2-4. B/W EVF BLOCK, VF-129 BOARD (TR913E)4 EVF block assembly 2 FFC-256 flexible flat cable (4P) 8 Finder (S) assembly 7 Rotate it in the direction of the arrow b and remove it in the direction of the arrow c. a 5 Screw c ! 6 Slide the button in the direction of the arrow a. ! FFC-256 flexible flat cable (4P)

3 Three tapping screws (B2 5)

b

Tilt lock (93)

1 FFC-236 flexible flat cable (50P)

! Remove the claw ! Cabinet (upper B) (93) assembly

! VF base(B)(93)

[How to remove the CRT unit]@ CRT socket (4P) @ CRT

! Two tapping screws (B2 5) @ Tapping screw (B2 5) @ EVF tally

9 Harness guide

! Two screws (M2 3)

! FFC-256 flexible flat cable (4P)

@ Anode cable (1P) Do not pull the cable, but remove it in the vertical direction. @ Remove the connector cover with a flat head () screwdriver.

@ CRT assembly

@ VF-129 board

@ CRT DT connector (4P)

! Cabinet (lower B) (93) assembly

! Tapping screw (B2 5)

[B/W EVF CHECK SERVICE POSITION]Adjustment remote commander (RM-95)

LANC jack

CPC-7 jig (J-6082-382-A)

CPC-7 jig

DC IN

Contacting surface

FP-43 flexible board

AC POWER ADAPTOR

AC IN

CRT assembly

VF-129 board Panel (D) (front) assembly Cabinet (R) assembly

2-5

2-5. LENS BLOCK7 Flexible board (from LENS block) (24P) 5 Screw (M2 3) 6 Screw (M2 3) a 3 FP-54 flexible board

8 LENS block

2 VL-25 board 1 Screw (M2 3)-21 VCard Bo 4

4 Screw (M2 3)

! MD frame (B) a ! Two screws (M2 3) 9 Screw (M2 3) 0 IM shield assembly

[LENS BLOCK CHECK SERVICE POSITION]Adjustment remote commander (RM-95)

LANC jack

CPC-7 jig (J-6082-382-A)

CPC-7 jig

Extension cable (J-6082-357-A) (16P)4 -21 rd VC BoaAC POWER ADAPTOR

DC IN

Contacting surface

AC IN

LENS BLOCK

FP-43 flexible board Cabinet (R) assembly Base (Use box or the like) Base (Supports the VL-25 board) (Fix the lens block using a vise or the like.)

2-6

2-6. MECHANISM DECK, VC-214, DD-117 BOARDS! Cabinet (L) assembly 4 Screw (M2 4), lock ace, p2 Remove it in the direction of the arrow b. b 8 Jack cover

Remove it in the direction of the arrow a. Remove it gently as a thin flexible board is held by a claw.7 Disengage the claw that fixes the flexible board. a

! Control switch block (SS-8500) ! Two tapping screws (B2 5)

2 Cassette Lid assembly 1 Two screws (M2 4), lock ace, p2 ! Slide it in the direction of the arrow c and disengage the claw e. Remove the control switch block(FK-8500) in the direction of the arrow d. @ Remove the claws ! Remove the claw e 5 Screw (M2 4), lock ace, p2

9 Screw

e

6 Battery panel (P) assembly

c

DD-117

d

@ VC-214 board ! DD-117 board-21 VCard o B 4

! Two screws (M2 3) ! Board to board connector (70P) 3 FFC-236 flexible flat cable (50P)

@ Screw (M2 3)

! Two screws (M2 4), lock ace, p2 @ PJ-94 board ! Screw (M2 3) @ Mechanism deck

Refer to page 2-8 for service position.

Cabinet (R) assembly

2-7

[MECHANISM DECK, VC-214, DD-117 BOARDS CHECK SERVICE POSITION]Base 1-3 (Use box or the like) Battery panel (P) assembly Control switch block (SS-8500) Base 2 Adjustment remote commander (RM-95)

AC IN DC IN

AC POWER ADAPTOR

DD-117 board Extension cable (J-6082-439-A) (70P) Mechanism deck Control switch block (FK-8500) Base 1

Base 3 FP-43 flexible board a

CPC-7 jig (J-6082-382-A) VC-214 board FFC-236 flexible flat cable (50P)

Panel (D) (front) assembly

PJ-94 board LENS block

VL-25 board

FP-46 flexible board

Extension Cable (J-6082-357-A) (16P) CD-209 board Base Flexible board Fix the lens block using a vise or the like. (from LENS block) (24P) Contacting surface Contacting surface

2-8

2-7. VIDEO LIGHT

3 Halogen lamp a

2 Remove the lamp holder in the direction of the arrow a. 1 Remove the claws

2-8. CF-58 BOARD (TR913E)3 FFC-256 flexible flat cable (4P) 7 CF-58 board 6 Five tapping screws (B2 5)

4 Two tapping screws (B2 5)

Claw

CF

-58

Claw5 Lithium battery retainer (92) 2 Control switch block (MR-8500) (8P)

Note : When attaching it. Align the switch position as shown.

1 Flexible board (4P)

CF-58 BOARD (TR950E)3 FP-47 flexible flat cable (20P) 7 CF-58 board 6 Five tapping screws (B2 5)

Claw 4 Two tapping screws (B2 5)

CF

-58

Claw5 Lithium battery retainer (92) 2 Control switch block (MR-8500) (8P)

Note : When attaching it. Align the switch position as shown.

1 Flexible board (4P)

2-9

2-9. HOW TO IDENTIFY DRUM AND NOTETYPE A (Direct bearing type) TYPE B (Shaft press fit type)

Circular rib

Radial rib

(When a drum is viewed from the top.)

NoteRef.No. TYPE A B M901 DGH-0F1A-R DGH-0E9A-R 808 SCREW ASSY, DRUM ATTACHED X-3947-895-1 SCREW (M1.4) 3-971-939-01

The fixing screw differs depending on the types of drums. Be sure to check the type of drum and use the screw of the same type. Be careful that the drum of DGH-0F1A-R (Type A) only is supplied as repair part. M901 A-7048-899-A DRUM BLOCK ASSY (DGH-0F1A-R) 808 808 X-3947-895-1 3-971-939-01 SCREW ASSY, DRUM ATTACHED (TYPE A) SCREW (M1.4) (TYPE B)

2-10

2-10.CIRCUIT BOARDS LOCATION

(TR913E)VF-129 (B/W EVF) CD-209 (CCD IMAGER) VL-25 (VIDEO LIGHT)

(TR950E)VF-126 (COLOR EVF) CD-209 (CCD IMAGER) VL-25 (VIDEO LIGHT)

DD-117 (DC/DC CONVERTER)

SE-85 (STEADY SHOT)

PJ-94 (AV IN/OUT)

MA-353 STEREO MIC AMP, LASER LINK

DD-117 (DC/DC CONVERTER)

SE-85 (STEADY SHOT)

PJ-94 (AV IN/OUT)

MA-353 STEREO MIC AMP, LASER LINK

(TR913E/TR950E)CF-58 (USER CONTROL)

VC-214 CAMERA PROCESSOR, Y/C PROCESSOR, FOCUS/ZOOM MOTOR DRIVE, REC/PB HEAD AMP, VIDEO/INTERFACE, IR TRANSMITTER, MODE CONTROL, SERVO, HI CONTROL, SYSTEM CONTROL, AUDIO PROCESSOR

2-11

2-11.FLEXIBLE BOARDS LOCATION

(TR913E/950E)CONTROL SWITCH BLOCK (FK-8500)

FP-46 From S/T REEL SENSOR From CAPSTAN MOTOR From DRUM MOTOR FP-44 From VIDEO From LOADING MOTOR, HEAD MODE SWITCH

(TR913E)CONTROL SWITCH BLOCK (SS-8500) FFC-256 FP-62

(TR950E)CONTROL SWITCH BLOCK (SS-8500) FP-47 FP-62

FFC-236 CONTROL SWITCH BLOCK (MR-8500)

FFC-236 CONTROL SWITCH BLOCK (MR-8500)

(TR913E/950E)FP-49 FP-54

FP-43 (From LENS BLOCK)2-12E

SECTION 3 BLOCK DIAGRAMS3-1. OVERALL BLOCK DIAGRAM

CCD-TR913E/TR950E

3-1

3-2

3-3

3-4

CCD-TR913E/TR950E

3-2. CAMERA/VIDEO BLOCK DIAGRAMIC1401 7 IC1402 6 IC502 @ CAMERA REC IC001 $ CAMERA REC IC001 1 CAMERA REC IC001 @,# CAMERA RECH 1.2Vp-p

H

1.1Vp-p

H

1.2Vp-p

IC202 ! CAMERA REC IC502 2 9 CAMERA REC/PB0.4Vp-p 0.2 sec 72 nsec 2.9Vp-p

IC202 ! CAMERA REC

1 sec/div, 0.1 V/div

0.1 sec/div

0.3Vp-p

0.2 sec/div, 1 V/div 0.4Vp-p H

IC501 @ CAMERA REC

H

7.0Vp-p

IC202 $ PB

0.1 sec/div

0.4Vp-p

IC501 ! CAMERA REC/PB

IC502 # PB IC001 ! PB0.3Vp-p H

IC1401 !,!

IC1401 3,4

3.0Vp-p 14.187 MHz

IC502 ! CAMERA REC/PB1 sec/div, 0.2 V/div

3.7Vp-p 14.187 MHz H

6.8Vp-p

14.187 MHz

2.9Vp-p

IC1401 !

IC1401 1,2

IC501 5 CAMERA REC/PB

CN001 !, Q001 C CAMERA REC

3.0Vp-p 28.374 MHz 3.3Vp-p 14.187 MHz H 6.8Vp-p

7.14 MHz

9.0Vp-p

IC202 $ PB IC501 @ CAMERA REC3.0Vp-p 13.325 MHz 7.0Vp-p

H

IC501 @ CAMERA REC IC202 6 CAMERA REC/PB50 nsec 3.0Vp-p

0.8Vp-p H

IC202 @ CAMERA REC/PB

IC202 3 CAMERA REC/PB

0.1Vp-p H H

0.45Vp-p

IC151 @ CAMERA REC/PB

IC151 @ CAMERA REC/PB

2Vp-p H H

2Vp-p

IC202 & CAMERA REC/PB

2.8Vp-p

IC151 ! CAMERA REC/PB IC202 @ CAMERA REC/PBH 1.5Vp-p

25 Hz

IC151 @ CAMERA REC/PB IR ON

0.3Vp-p H

IC202 # CAMERA REC/PB0.5Vp-p

H 1.0Vp-p H

3-5

3-6

3-7

3-8

CCD-TR913E/TR950E

3-3. VTR/CAMERA CONTROL BLOCK DIAGRAM

IC402 1

20.0 MHz

1.7Vp-p

IC402 $

25 Hz

2.8Vp-p

3-9

3-10

3-11

CCD-TR913E/TR950E

3-4. SERVO BLOCK DIAGRAMIC801 ! IC802 9 IC801 ^150 Hz 2.8Vp-p 10.3 sec 2 sec 0.1Vp-p 150 Hz 0.75Vp-p

IC801 1,2,@

1.2Vp-p

IC802 7

IC801 !

1.0 msec/div

100mV

IC801 4

25 Hz

2.8Vp-p 2 sec

0.75Vp-p

IC402 1

20.0 MHz

1.7Vp-p

IC402 $

25 Hz

2.8Vp-p

3-12

3-13

3-14

CCD-TR913E/TR950E

CCD-TR913E/TR950E

3-5. MODE CONTROL BLOCK DIAGRAM

IC604 $

20.0 MHz

3.2Vp-p

IC604 %

3.2Vp-p 32.768 KHz

3-15

3-16

3-17

CCD-TR913E/TR950E

3-6. AUDIO BLOCK DIAGRAMIC751 $ CAMERA REC/PB IR ON IC751 @ CAMERA REC/PB IR ON

0.22Vp-p H

0.5 sec/div

0.22Vp-p

IC751 7 CAMERA REC/PB

4.43 MHz

0.2Vp-p

3-19

3-20

3-21

3-22

CCD-TR913E/TR950E

3-7. COLOR EVF BLOCK DIAGRAM (CCD-TR950E)IC4501 @8.0Vp-p

2H

IC4501 @ IC4501 82H

8.0Vp-p

H

0.55Vp-p

IC4501 !

0.3Vp-p H

IC4501 9

IC4501 @8.0Vp-p

IC4601 !H 0.3Vp-p 2H

11.0Vp-p H

3-23

3-24

3-25

CCD-TR913E/TR950E

CCD-TR913E/TR950E

3-8. B/W EVF BLOCK DIAGRAM (CCD-TR913E)

IC901 !

IC901 !

0.9Vp-p H H

2.4Vp-p

IC901 !

1.1Vp-p H

IC901 3

IC901 1,5

2.0Vp-p 20 msec 2.0Vp-p 20 msec

IC901 7

1.1Vp-p 20 msec

3-27

3-28

CCD-TR913E/TR950E

3-9. POWER BLOCK DIAGRAM

3-29

3-30

3-31

3-32E

SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS4-1. FRAME SCHEMATIC DIAGRAM-1

CCD-TR913E/TR950E

4-1

4-2

4-3

FRAME SCHEMATIC DIAGRAM (1/2)

CCD-TR913E/TR950E

FRAME SCHEMATIC DIAGRAM-2

FRAME SCHEMATIC DIAGRAM (2/2)

4-4

4-5

4-6

CCD-TR913E/TR950E

4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMSTHIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block)(For printed wiring boards) b: Pattern from the side which enables seeing. (The other layers' patterns are not indicated.) Through hole is omitted. Circled numbers refer to waveforms. There are few cases that the part printed on diagram isnt mounted in this model. Chip parts. Transistor DiodeC 65 4 45 6 4 5 1 2 3 3 3

CD-209 (CCD IMAGER) PRINTED WIRING BOARD Ref. No. CD-209 Board; 10,000 Series CD-209 BOARDC1401 C1405 C1406 C1407 C1408 C1409 C1410 C1411 C1412 A-2 A-1 A-1 B-2 B-2 B-1 B-1 B-2 B-1

(Measuring conditions voltage and waveform) Voltages and waveforms are measured between the measurement points and ground when camera shoots color bar chart of pattern box. They are reference values and reference waveforms. (VOM of DC 10 M input impedance is used.). Voltage values change depending upon input impedance of VOM used.) 1. ConnectionPattern box

CN1401 B-3 IC1401 A-3 IC1402 B-2 L1401 L1402 R1401 R1405 R1406 R1407 R1408 R1409 A-2 B-1 A-1 A-1 B-2 B-2 B-2 B-1

B

E

12 3

32 1

32 1

54 3

2

1

2

1

2

1

(For schematic diagrams) All capacitors are in F unless otherwise noted. pF : F. 50V or less are not indicated except for electrolytics and tantalums. Chip resistors are 1/10W unless otherwise noted. k=1000, M=1000k. Caution when replacing chip parts. New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat. Some chip part will be indicated as follows. Example C541 L452 22U 10UH TA A 2520

1.5 m

Front of the lens

Kinds of capacitor Temperature characteristics External dimensions (mm) Constants of resistors, capacitors, ICs and etc with XX indicate that they are not used. In such cases, the unused circuits may be indicated. Parts with 5 differ according to the model/destination. Refer to the mount table for each function. All variable and adjustable resistors have characteristic curve B, unless otherwise noted. Signal name XEDIT EDIT PB/XREC PB/REC 2 : non flammable resistor 1 : fusible resistor C : panel designation A : B+ Line B : B Line J : IN/OUT direction of (+,) B LINE. C : adjustment for repair. Circled numbers refer to waveforms. Note : The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.

2. Adjust the distance so that the output waveform of Fig. a and the Fig. b can be obtain.

Yellow

HWhite Magenta Red Blue Cyan Green

A B

A=B

B AFor printed wiring boards This board is six-layer print board. However, the patterns of layers two to five have not been included in the diagram.

Fig. a (Video output terminal output waveform)

Electron beam scanned frameYellow Cyan Green White Magenta Red Blue

CRT picture frame

There are few cases that the part printed on this diagram isnt mounted in this model.(TR913E) (TR950E)CD-209 (CCD IMAGER) VL-25 (VIDEO LIGHT) VF-126 (COLOR EVF) CD-209 (CCD IMAGER) VL-25 (VIDEO LIGHT)

Fig.b (Picture on monitor TV)When indicating parts by reference number, pleas include the board name.

VF-129 (B/W EVF)

CD-209 BOARDCAMERA REC

1 IC1401 1,2DD-117 (DC/DC CONVERTER) MA-353 STEREO MIC AMP, LASER LINK DD-117 (DC/DC CONVERTER) MA-353 STEREO MIC AMP, LASER LINK

2 IC1401 3,4

3 IC1401 7

4 IC1401 !

5 IC1401 !,!

6 IC1402 6

PJ-94 (AV IN/OUT) SE-85 (STEADY SHOT)

PJ-94 (AV IN/OUT) SE-85 (STEADY SHOT)

H

6.8Vp-p

6.8Vp-p H H 1.1Vp-p 14.187 MHz

3.3Vp-p 14.187 MHz

3.7Vp-p H 1.2Vp-p

4-7

4-8

4-9

CCD IMAGERCD-209

CCD-TR913E/TR950EVC-214 (CAMERA PROCESSOR, Y/C PROCESSOR, FOCUS/ZOOM MOTOR DRIVE, REC/PB HEAD AMP, VIDEO/INTERFACE, IR, MODE CONTROL, SYSTEM CONTROL, AUDIO PROCESSOR) PRINTED WIRING BOARD Ref. No. VC-214 Board; 1,000 Series VC-214 BOARD (SIDE A)C006 C008 C009 C011 C021 C022 C027 C028 C030 C031 C034 C035 C036 C038 C039 C040 C041 C045 C046 C047 C048 C052 C053 C056 C058 C062 C065 C069 C071 C073 C075 C078 C079 C081 C082 C084 C085 C088 C089 C156 C157 C158 C160 C161 C166 C171 C185 C187 C188 C189 C201 C204 C206 C209 C210 C217 C219 C224 C225 C226 C229 C230 C237 C239 C241 C245 C248 C250 C253 C306 C307 C308 C309 C310 C312 C313 C314 C315 C316 C317 C318 C319 C320 C321 C322 C323 A-4 A-5 B-5 B-5 B-5 B-5 A-4 B-4 A-5 B-4 B-5 C-4 B-4 B-3 B-4 B-4 B-4 B-5 C-4 B-5 B-4 B-5 B-5 B-4 B-4 C-5 C-6 C-6 C-5 B-3 C-4 C-4 C-4 C-5 C-5 C-5 C-6 C-5 C-4 C-2 C-2 C-2 C-2 C-2 C-2 C-1 C-2 C-2 B-1 B-1 F-7 E-8 E-7 D-5 D-6 E-7 E-8 E-7 E-7 E-7 F-5 E-6 E-7 F-7 E-8 E-7 E-7 E-7 G-6 A-1 A-1 B-1 B-1 B-1 A-1 A-1 A-1 B-1 B-1 A-1 A-1 A-1 A-1 A-1 B-1 A-1 C324 C325 C326 C327 C328 C329 C330 C331 C332 C333 C334 C335 C336 C337 C338 C339 C340 C341 C342 C343 C344 C345 C346 C347 C389 C402 C411 C412 C415 C416 C417 C418 C419 C502 C512 C513 C516 C517 C519 C520 C521 C522 C523 C524 C525 C526 C527 C528 C529 C530 C532 C533 C534 C535 C551 C552 C553 C555 C557 C558 C560 C561 C562 C565 C567 C568 C569 C570 C571 C572 C605 C612 C615 C616 C617 C618 C619 C620 C621 C622 C623 C624 C628 C629 C635 C636 A-1 B-1 B-2 A-1 B-2 A-2 B-2 B-2 A-2 A-2 B-2 A-2 B-2 A-3 B-3 A-3 B-3 A-3 B-3 B-1 B-3 A-3 A-3 B-3 A-3 A-7 B-9 B-8 B-8 B-8 C-7 A-7 B-8 E-5 D-4 D-5 E-4 D-4 D-4 D-4 D-4 D-4 D-4 D-4 D-4 D-4 D-4 D-5 D-5 D-5 D-4 D-4 E-5 D-4 G-4 F-4 G-4 E-4 F-4 F-4 F-4 F-5 F-5 E-4 F-5 F-5 F-5 F-5 F-5 G-4 G-8 E-8 E-8 E-8 E-9 E-9 E-9 E-9 E-8 E-8 E-8 E-8 G-7 G-7 E-8 E-8 C801 C802 C803 C804 C805 C806 C807 C808 C809 C810 C811 C812 C813 C814 C815 C816 C817 C818 C819 C820 C821 C822 C823 C836 C838 C839 C840 CN001 CN501 CN551 CN901 CN902 CN903 CN905 CN906 CN907 CN908 CN911 CN914 D002 D551 D610 D910 D911 FB002 FB004 FB201 FB203 FB206 FB506 FB602 IC001 IC202 IC301 IC402 IC502 IC551 IC604 IC801 L001 L002 L003 L004 L006 L009 L012 L013 L016 L018 L204 L205 L207 L502 L555 Q003 Q024 Q027 Q028 Q029 Q031 A-7 A-7 A-6 B-6 B-6 B-7 B-6 B-7 B-7 B-7 B-6 B-7 B-6 C-6 B-7 B-6 C-6 B-6 B-6 B-7 B-6 B-7 A-8 A-9 A-8 A-9 A-9 A-4 E-5 G-5 A-2 D-7 A-1 A-6 A-7 D-9 A-8 C-7 C-9 C-4 G-4 D-6 D-3 E-3 A-4 A-5 E-8 F-5 E-7 E-5 E-8 B-4 F-6 B-2 B-8 D-5 F-4 F-8 B-6 A-3 B-5 B-5 B-3 C-5 B-3 C-3 C-5 C-5 C-5 D-7 D-6 E-7 D-4 F-5 A-5 B-4 C-4 C-4 C-4 D-4 Q033 Q034 Q036 Q040 Q043 Q044 Q204 Q205 Q208 Q213 Q214 Q215 Q216 Q217 Q310 Q501 Q551 Q552 Q553 Q554 Q608 Q609 Q610 Q611 Q801 Q802 Q803 Q806 R004 R014 R035 R038 R039 R043 R044 R045 R046 R056 R058 R063 R071 R072 R073 R074 R075 R081 R082 R085 R086 R092 R093 R096 R098 R099 R101 R102 R103 R107 R113 R165 R166 R167 R170 R175 R183 R184 R201 R203 R206 R207 R209 R212 R213 R214 R215 R216 R217 R218 R219 R220 R221 R222 R225 R227 R228 C-4 C-4 C-5 C-6 C-4 C-4 D-6 E-8 D-6 D-6 D-6 E-7 E-7 E-8 A-2 D-4 G-5 F-4 E-5 G-5 G-9 G-8 G-8 G-8 C-6 B-6 C-7 A-9 A-5 B-5 B-5 B-4 B-4 C-4 B-4 B-4 C-4 B-4 B-4 C-5 D-4 B-4 B-4 B-4 C-3 C-4 C-4 C-4 D-4 C-4 C-5 C-4 C-4 C-4 C-4 C-5 C-5 C-5 C-5 C-3 C-2 C-3 C-3 C-1 C-2 C-2 E-6 E-8 E-8 E-6 E-6 D-6 E-6 D-6 D-6 E-6 F-7 D-6 D-7 D-6 D-6 E-7 D-6 E-6 D-6 R229 R230 R231 R232 R233 R234 R235 R236 R237 R238 R239 R241 R242 R243 R251 R252 R253 R255 R258 R259 R260 R261 R262 R308 R310 R313 R317 R318 R319 R320 R321 R322 R323 R325 R331 R343 R350 R405 R406 R407 R409 R410 R416 R420 R421 R432 R433 R434 R435 R436 R437 R440 R441 R513 R514 R515 R522 R523 R524 R525 R532 R551 R554 R555 R556 R557 R558 R559 R560 R561 R562 R563 R564 R565 R566 R567 R568 R569 R570 R571 R572 R573 R574 R575 R576 R577 E-6 E-6 E-7 E-6 E-6 E-6 E-6 E-6 E-6 E-6 E-7 E-6 E-7 E-8 F-7 F-7 G-7 E-8 E-6 E-7 D-6 E-7 E-7 B-1 B-1 A-1 A-1 B-2 A-3 B-2 A-1 A-3 B-3 B-3 A-3 A-3 A-3 A-7 A-7 A-8 A-8 A-8 A-8 B-8 B-8 B-9 B-9 B-8 B-9 B-8 A-8 B-9 C-8 D-4 D-4 D-4 D-4 D-5 D-5 D-5 E-4 G-4 G-4 G-5 F-4 G-4 F-4 F-4 F-4 E-4 F-4 F-4 F-4 F-4 F-4 F-5 E-4 F-4 F-5 E-4 E-4 E-4 F-5 E-4 F-5 E-4 R579 R583 R605 R606 R610 R611 R613 R614 R622 R628 R645 R650 R664 R666 R667 R668 R669 R670 R671 R672 R673 R681 R682 R683 R684 R685 R690 R691 R693 R695 R696 R697 R698 R801 R802 R803 R804 R805 R806 R807 R808 R809 R813 R814 R815 R823 R825 R836 R837 R917 R918 R919 R920 R932 R933 X601 X602 F-4 G-5 G-9 G-7 G-8 G-8 G-8 G-7 F-9 F-9 E-8 G-7 E-8 E-9 E-9 E-9 E-9 E-8 E-8 E-8 E-8 F-9 F-9 G-9 F-9 G-9 E-8 E-8 G-9 G-9 G-8 G-8 E-8 B-6 B-6 B-6 A-6 A-6 B-6 A-6 B-6 B-6 A-8 A-7 A-7 A-8 A-8 A-9 A-9 C-8 C-8 C-8 C-8 D-8 D-8 G-8 G-7

For printed wiring boards This board is six-layer print board. However, the patterns of layers two to five have not been included in the diagram. Chip parts TransistorC

B

E

There are few cases that the part printed on this diagram isnt mounted in this model.(TR913E/TR950E)CF-58 (USER CONTROL)

VC-214 CAMERA PROCESSOR, Y/C PROCESSOR, FOCUS/ZOOM MOTOR DRIVE, REC/PB HEAD AMP, VIDEO/INTERFACE, IR TRANSMITTER, MODE CONTROL, SERVO, HI CONTROL, SYSTEM CONTROL, AUDIO PROCESSOR

CAMERA PROCESS, REC/PB HEAD AMP, VIDEO PROCESS, AUDIO, SERVO, SYSTEM CONTROL, MODE CONTROLVC-214

4-11

4-12

CCD-TR913E/TR950E

CCD-TR913E/TR950E

VC-214 BOARD (SIDE B)C001 C004 C005 C007 C012 C024 C029 C032 C037 C042 C049 C050 C051 C054 C055 C057 C059 C060 C061 C066 C067 C068 C070 C072 C074 C076 C080 C083 C086 C087 C090 C152 C159 C162 C163 C164 C168 C169 C170 C172 C173 C174 C175 C176 C177 C178 C179 C180 C181 C182 C183 C184 C186 C190 C191 C192 C202 C203 C205 C207 C208 C211 C212 C213 C218 C227 C232 C233 C234 C235 C236 C243 C244 C246 C247 C249 C252 C301 C302 C371 C372 C378 C380 C381 C382 C383 A-15 A-14 B-14 A-14 B-14 B-15 C-14 B-14 B-14 C-14 B-14 B-15 B-15 C-15 C-13 B-14 C-14 B-15 C-14 A-15 A-15 B-15 B-15 B-16 B-16 B-16 C-15 B-15 C-13 C-14 A-15 C-16 E-15 C-16 C-16 C-16 C-16 C-18 C-16 C-18 C-18 C-18 C-18 C-18 C-18 B-18 C-18 C-17 C-17 B-17 B-17 C-17 C-16 C-16 D-15 D-15 E-11 E-11 G-14 E-12 E-12 E-11 E-11 E-13 E-12 E-13 E-11 F-13 E-13 E-11 E-11 G-12 F-12 E-13 E-13 G-12 G-12 B-18 A-18 C-15 C-15 D-15 C-14 C-14 C-15 C-15 C384 C385 C386 C387 C388 C390 C404 C405 C406 C410 C414 C420 C421 C501 C503 C506 C507 C509 C510 C514 C515 C518 C531 C536 C554 C556 C559 C563 C564 C566 C607 C610 C611 C613 C625 C626 C627 C630 C634 C637 C702 C703 C704 C705 C706 C707 C708 C710 C711 C712 C713 C714 C715 C716 C717 C751 C752 C753 C754 C755 C757 C758 C759 C760 C761 C762 C763 C764 C766 C767 C768 C769 C770 C771 C772 C773 C774 C775 C777 C778 C781 C824 C825 C826 C827 C828 C-14 C-15 C-15 C-15 C-15 D-15 C-12 B-12 B-12 C-11 C-11 B-11 B-11 E-15 E-14 F-14 E-14 F-14 E-15 E-14 E-14 E-14 D-13 F-14 F-14 F-14 F-14 F-15 F-15 F-15 F-11 G-10 F-11 F-10 E-11 E-11 G-11 F-11 F-11 F-11 A-13 B-14 B-13 B-13 B-13 B-13 A-13 A-13 B-13 B-13 B-13 A-13 A-13 B-12 A-12 B-16 A-16 A-16 A-16 A-16 A-16 A-16 B-17 B-17 B-16 B-17 B-17 B-17 A-17 B-17 B-17 A-18 A-18 B-17 A-18 B-17 A-17 A-17 A-18 A-18 A-18 A-10 A-12 A-12 A-11 A-11 C829 C830 C831 C832 C833 C834 C835 C837 A-11 A-11 A-12 A-11 A-11 A-11 A-11 A-10 Q019 Q020 Q021 Q023 Q025 Q026 Q030 Q032 Q038 Q039 Q041 Q042 Q045 Q151 Q153 Q154 Q156 Q202 Q203 Q301 Q302 Q305 Q306 Q307 Q308 Q309 Q371 Q372 Q607 Q619 Q620 Q701 Q702 Q703 Q704 Q705 Q804 Q805 R003 R005 R006 R007 R008 R009 R015 R020 R021 R023 R025 R027 R029 R031 R032 R034 R037 R040 R041 R042 R047 R048 R049 R050 R051 R052 R053 R054 R055 R057 R059 R060 R062 R066 R066 R067 R069 R070 R076 R077 R078 R079 R080 R083 R084 R087 R094 C-15 B-15 A-16 A-16 B-16 B-15 B-15 B-15 B-15 C-15 C-14 C-15 C-14 C-16 C-16 C-16 C-16 E-11 E-11 B-18 B-18 B-18 B-18 A-18 B-18 B-18 C-16 D-16 G-11 F-11 F-10 B-13 B-13 A-13 A-13 A-13 A-10 A-10 B-14 B-14 B-14 B-14 B-14 B-14 B-14 B-14 B-14 B-15 B-14 B-15 A-15 A-14 B-14 C-14 B-14 B-15 B-14 B-15 B-14 B-14 A-15 A-15 A-15 B-14 C-14 C-14 B-14 B-15 C-13 C-14 B-15 A-16 B-16 A-15 A-16 A-16 B-16 B-16 B-16 B-16 B-15 B-15 B-15 C-15 B-15 R095 R104 R105 R106 R109 R110 R112 R152 R154 R157 R161 R162 R176 R177 R178 R179 R180 R202 R204 R205 R208 R210 R211 R223 R224 R226 R240 R244 R245 R246 R247 R248 R249 R250 R254 R257 R302 R303 R304 R305 R311 R314 R315 R316 R371 R372 R373 R374 R375 R376 R377 R378 R379 R382 R383 R384 R385 R386 R386 R389 R390 R390 R402 R403 R404 R408 R412 R414 R415 R419 R424 R426 R427 R428 R429 R430 R431 R502 R503 R504 R508 R510 R511 R512 R521 R526 C-15 B-15 B-15 B-15 C-14 C-14 C-15 C-16 C-16 C-16 C-16 C-16 C-18 B-17 B-17 B-17 B-17 E-11 E-11 E-11 E-11 E-11 E-11 E-11 E-11 E-12 E-12 E-11 E-12 E-11 E-11 E-11 E-11 G-12 C-11 E-13 A-18 B-18 B-18 A-18 B-18 A-18 A-18 B-18 C-16 D-16 D-15 D-15 C-16 D-15 C-15 D-16 D-15 C-15 C-15 D-14 C-15 C-15 C-16 C-15 C-15 C-15 B-12 B-11 B-12 C-12 C-12 B-11 B-11 C-11 B-11 B-11 B-11 B-11 B-11 B-11 C-11 E-15 E-15 F-14 E-14 E-14 D-14 D-13 D-14 D-14 R527 R530 R603 R604 R607 R608 R612 R618 R619 R620 R621 R624 R625 R627 R629 R630 R631 R632 R633 R634 R635 R636 R637 R638 R639 R640 R641 R642 R643 R644 R646 R647 R648 R649 R651 R652 R653 R654 R655 R662 R663 R665 R675 R676 R677 R678 R679 R680 R686 R687 R689 R692 R699 R700 R701 R702 R703 R704 R705 R706 R707 R708 R709 R710 R711 R712 R713 R714 R715 R716 R717 R718 R719 R720 R721 R722 R723 R724 R725 R726 R752 R753 R755 R756 R757 R758 D-14 F-14 G-11 G-11 E-10 G-11 F-11 F-10 F-10 G-10 F-10 G-10 F-10 F-10 F-10 F-11 G-11 G-10 E-11 E-10 F-11 F-11 G-11 G-11 G-11 G-11 G-11 G-11 F-11 G-11 F-11 F-11 F-11 G-11 G-11 F-11 F-11 F-11 F-12 F-11 F-11 F-11 F-11 F-11 F-11 G-11 G-10 G-10 F-11 F-11 F-11 G-10 E-11 E-10 B-13 B-13 B-13 B-13 B-13 B-13 B-13 B-13 B-14 A-13 A-13 B-13 B-13 B-13 B-13 A-13 A-13 A-13 A-13 A-13 A-12 A-12 A-12 A-12 B-12 B-12 A-16 A-16 B-16 B-17 B-17 A-16 R759 R760 R761 R762 R763 R764 R765 R765 R766 R767 R768 R770 R771 R772 R773 R774 R775 R776 R777 R810 R811 R812 R816 R817 R818 R819 R820 R821 R822 R824 R827 R828 R828 R829 R830 R831 R832 R833 R834 R835 R916 R921 R922 R923 R924 R925 R926 R927 R928 R929 R930 R931 R934 R935 R936 R937 R938 R939 R940 R941 R942 R943 R944 R945 TH401 X151 X401 X501 A-16 B-17 A-16 A-17 A-17 B-17 A-17 B-17 A-17 B-17 A-17 A-17 A-17 A-17 A-17 A-18 A-17 A-16 A-16 A-12 A-12 A-12 A-12 A-12 A-12 A-12 A-11 A-12 A-10 A-10 A-11 A-11 A-11 A-11 A-11 A-10 A-10 A-10 A-10 A-10 D-12 B-11 D-10 D-10 D-10 D-10 G-14 G-14 C-12 C-12 D-12 D-11 D-12 D-12 D-12 D-12 E-12 E-12 E-12 E-12 E-12 E-12 E-12 E-12 B-16 C-18 C-13 D-14

CN904 B-18 CN909 G-15 CN910 D-10 D001 D201 D202 D371 D611 D804 D808 D809 D814 D815 D902 FB151 FB152 FB202 FB204 FB205 FB402 FB501 FB503 FB504 FB505 FB701 FB702 IC151 IC152 IC201 IC204 IC371 IC401 IC501 IC552 IC602 IC603 IC701 IC751 IC802 L005 L007 L008 L010 L011 L015 L017 L019 L020 L152 L153 L154 L155 L156 L201 L202 L203 L206 L209 L501 L552 L553 L701 L702 L704 L751 L752 L753 Q001 Q002 Q012 Q016 Q017 C-14 E-11 E-11 C-15 F-10 G-11 F-10 F-11 F-11 F-11 E-13 C-16 E-15 G-13 G-12 F-12 C-11 E-15 E-14 E-14 D-14 A-13 A-13 C-17 E-15 G-14 F-13 D-15 C-11 E-14 F-14 F-11 F-10 B-12 A-17 A-11 C-14 A-15 B-16 B-16 B-16 B-15 C-14 A-16 A-14 C-18 C-16 C-16 B-18 D-15 E-10 D-13 E-13 E-12 E-13 D-13 F-15 F-15 A-13 B-13 A-13 B-17 B-17 B-17 B-14 B-14 B-14 B-15 A-15

4-13

4-14

CAMERA PROCESS, REC/PB HEAD AMP, VIDEO PROCESS, AUDIO, SERVO, SYSTEM CONTROL, MODE CONTROLVC-214

CCD-TR913E/TR950E

CCD-TR913E/TR950E

For schematic diagram Refer to page 4-11 for printed wiring board.

VC-214 BOARD (1/10)1 IC501 5CAMERA REC/PB

7 IC502 !CAMERA REC

3.0Vp-p 28.374 MHz

72 nsec

2.9Vp-p

2 IC501 !CAMERA REC/PB

7 IC502 ! PB

3.0Vp-p 14.187 MHz

72 nsec

2.9Vp-p

3 IC501 @CAMERA REC

8 IC502 !CAMERA REC/PB

14.187 MHz 50 nsec 3.0Vp-p

2.9Vp-p

4 IC501 @CAMERA REC

9 IC502 @CAMERA REC

H

7.0Vp-p H 1.2Vp-p

5 IC501 @CAMERA REC

! IC502 # PB

H

7.0Vp-p

0.3Vp-p H

6 IC502 2 9CAMERA REC/PB

72 nsec

2.9Vp-p

CAMERA PROCESSORVC-214 (1/10)

4-17

4-18

CCD-TR913E/TR950E

For schematic diagram Refer to page 4-11 for printed wiring board. Refer to page 4-23 for waveforms.

4-19

4-20

4-21

4-22

Y/C PROCESSORVC-214 (2/10)

CCD-TR913E/TR950E

CCD-TR913E/TR950E

For schematic diagram Refer to page 4-11 for printed wiring board.

VC-214 BOARD (2/10)! IC202 3CAMERA REC/PB

! IC202 #CAMERA REC/PB

0.45Vp-p H H

1.0Vp-p

! IC202 6CAMERA REC/PB

! Q217 EPB

0.8Vp-p H H

0.3Vp-p

! IC202 !CAMERA REC

! IC202 $PB

0.4Vp-p H 0.1 sec/div

0.4Vp-p

! IC202 !CAMERA REC

@ IC202 $PB

0.4Vp-p 0.2 sec 13.325 MHz

3.0Vp-p

! IC202 @CAMERA REC/PB

@ IC202 ^CAMERA REC/PB

0.3Vp-p H 14.187 MHz

3.0Vp-p

! IC202 @CAMERA REC/PB

@ IC202 &CAMERA REC/PB

0.1Vp-p H 25 Hz

2.8Vp-p

4-23

FOCUS/ZOOM MOTOR DRIVEVC-214 (3/10)

4-25

4-26

CCD-TR913E/TR950E

For schematic diagram Refer to page 4-11 for printed wiring board. Refer to page 4-30 for waveforms.

4-27

4-28

4-29

REC/PB HEAD AMPVC-214 (4/10)

CCD-TR913E/TR950E

For schematic diagram Refer to page 4-11 for printed wiring board.

VC-214 BOARD (4/10)@ CN001 !, Q001 CCAMERA REC

VC-214 BOARD (5/10)@ IC151 3CAMERA REC/PB

0.48Vp-p 7.14 MHz 9.0Vp-p H

@ IC001 1CAMERA REC

@ IC151 5CAMERA REC/PB

0.1 sec/div

0.3Vp-p

H

0.3Vp-p

@ IC001 !PB

# IC151 !CAMERA REC/PB

1 sec/div, 0.2 V/div

H

1.5Vp-p

@ IC001 @,#CAMERA REC

# IC151 @CAMERA REC/PB

2Vp-p 0.2 sec/div, 1 V/div H

@ IC001 $CAMERA REC

# IC151 @CAMERA REC/PB IR ON

1 sec/div, 0.1 V/div

0.5Vp-p H

# IC151 @CAMERA REC/PB

2Vp-p H

VIDEO/INTERFACEVC-214 (5/10)

4-30

4-31

4-32

CCD-TR913E/TR950E

CCD-TR913E/TR950E

For schematic diagram Refer to page 4-11 for printed wiring board.

VC-214 BOARD (6/10) # IC751 7CAMERA REC/PB

4.43 MHz

0.2Vp-p

# IC751 @CAMERA REC/PB IR ON

0.5 sec/div

0.22Vp-p

# IC751 $CAMERA REC/PB IR ON

0.22Vp-p H

4-33

4-34

IR TRANSMITTERVC-214 (6/10)

CCD-TR913E/TR950E

For schematic diagram Refer to page 4-11 for printed wiring board.

VC-214 BOARD (7/10)CAMERA REC/PB

# IC402 1

20.0 MHz

1.7Vp-p

# IC402 $

25 Hz

2.8Vp-p

MODE CONTROLVC-214 (7/10)

4-36

4-37

4-38

CCD-TR913E/TR950E

For schematic diagram Refer to page 4-11 for printed wiring board.

FP-249 (S/T REEL SENSOR), FP-356 (TOP SENSOR), FP-355 (TAPE LED) FLEXIBLE BOARD Ref. No. FP-249, 356, 355 FLEXIBLE board; 5,000 series

VC-214 BOARD (8/10)CAMERA REC/PB

# IC801 1,2,@

150 Hz

1.2Vp-p

$ IC801 !

25 Hz

2.8Vp-p

$ IC801 !

150 Hz

2.8Vp-p

$ IC802 7

1.0 msec/div

100mV

$ IC802 9

0.1Vp-p 10.3 sec

4-39

4-40

4-41

SERVOVC-214 (8/10)

/ S/T REEL SENSOR, TOP SENSOR, TAPE LEDFP-249, FP-356, FP-355

CCD-TR913E/TR950E

VL-25 (VIDEO LIGHT) PRINTED WIRING BOARD Ref. No. VL-25 Board; 2,000 Series

For schematic diagram Refer to page 4-11 for printed wiring board.

VC-214 BOARD (9/10)CAMERA REC/PB

$ IC604 $

20.0 MHz

3.2Vp-p

$ IC604 %

3.2Vp-p 32.768 KHz

For printed wiring boards Chip parts TransistorC

VL-25 BOARDC151 C152 C153 A-2 A-3 A-2

CN151 A-3B E

There are few cases that the part printed on this diagram isnt mounted in this model.(TR913E)VF-129 (B/W EVF) CD-209 (CCD IMAGER) VL-25 (VIDEO LIGHT)

D151 D152 D153 L151 Q151 Q152

A-5 A-2 A-2 A-2 A-2 A-4 A-4 A-2 A-2 A-3

(TR950E)VF-126 (COLOR EVF) CD-209 (CCD IMAGER) VL-25 (VIDEO LIGHT)

R151 R152 R153 R154

DD-117 (DC/DC CONVERTER)

PJ-94 (AV IN/OUT) SE-85 (STEADY SHOT)

MA-353 STEREO MIC AMP, LASER LINK

DD-117 (DC/DC CONVERTER)

PJ-94 (AV IN/OUT) SE-85 (STEADY SHOT)

MA-353 STEREO MIC AMP, LASER LINK

VIDEO LIGHTVL-25

/ HI CONTROLVC-214 (9/10)

4-43

4-44

4-45

4-46

CCD-TR913E/TR950E

For schematic diagram Refer to page 4-11 for printed wiring board.

4-47

4-48

4-49

AUDIOVC-214 (10/10)

CCD-TR913E/TR950E

SE-85 (STEADY SHOT), PJ-94 (AV IN/OUT) PRINTED WIRING BOARDS Ref. No. SE-85, PJ-94 Board; 2,000 Series SE-85 BOARDC451 C452 C453 C454 C457 C458 C459 C460 C461 C462 C463 C464 C465 C466 C467 C468 C469 C470 B-5 D-6 C-2 E-2 C-6 C-6 C-6 D-3 C-6 C-3 D-6 B-6 B-6 C-5 A-2 A-2 A-2 A-2

PJ-94 BOARDC101 C102 C103 C104 C105 C106 C107 C108 C109 C110 C111 C-4 D-4 B-4 C-4 A-4 B-4 B-4 A-4 E-4 E-4 A-4

CN101 C-5 D101 D102 D103 D104 D105 D106 J101 L101 L102 L103 L104 Q101 Q102 R101 R102 R103 R104 R105 R106 R107 R108 R109 A-4 C-5 C-5 E-4 E-4 E-4 E-1 C-4 C-5 B-4 B-4 E-4 D-4 D-5 D-4 D-4 D-4 D-4 E-4 E-4 E-5 C-4

CN451 A-3 D451 D452 IC451 J451 L451 L453 L454 R451 R452 R453 R454 R457 R458 R458 R459 R460 R461 SE451 SE452 A-2 A-2 C-6 A-1 B-2 A-2 A-2 B-5 D-6 C-6 B-5 C-6 C-6 C-6 C-6 C-5 B-6 B-3 E-3

(TR913E)VF-129 (B/W EVF) CD-209 (CCD IMAGER) VL-25 (VIDEO LIGHT)

(TR950E)VF-126 (COLOR EVF) CD-209 (CCD IMAGER) VL-25 (VIDEO LIGHT)

For printed wiring boards Chip parts TransistorC

Diode3

B

E

2

1

There are few cases that the part printed on this diagram isnt mounted in this model.DD-117 (DC/DC CONVERTER) PJ-94 (AV IN/OUT) SE-85 (STEADY SHOT) MA-353 STEREO MIC AMP, LASER LINK DD-117 (DC/DC CONVERTER) PJ-94 (AV IN/OUT) SE-85 (STEADY SHOT) MA-353 STEREO MIC AMP, LASER LINK

STEADY SHOTSE-85

/ AV IN/OUTPJ-94

4-50

4-51

4-52

CCD-TR913E/TR950E

4-53

4-54

STEADY SHOTSE-85

/ AV IN/OUTPJ-94

CCD-TR913E/TR950E

MA-353 (STEREO MIC AMP, LASER LINK) PRINTED WIRING BOARD Ref. No. MA-353 Board; 2,000 Series MA-353 BOARDC301 C302 C303 C304 C305 C306 C333 C334 C335 C336 C337 C338 C339 C340 C341 C342 C343 C344 C345 C346 C347 C348 C349 C350 C351 C352 C353 C354 C355 C356 C357 C358 C359 C360 C361 C362 C363 C364 C365 C366 C367 C368 C369 C370 C371 C372 C374 C375 C376 C377 C378 A-6 A-7 B-5 A-5 B-6 B-4 C-8 C-8 C-8 D-8 C-8 C-8 C-7 C-8 C-2 C-8 C-7 C-1 C-7 D-8 C-2 D-7 D-7 D-2 D-8 D-8 D-8 D-7 D-2 C-7 C-7 C-2 C-2 C-7 C-7 D-2 D-2 D-2 D-2 D-2 D-2 D-2 C-7 D-2 C-6 C-6 C-6 D-2 C-7 A-8 D-2 J301 L301 Q301 Q302 Q303 Q304 Q305 R301 R302 R303 R304 R305 R306 R307 R308 R309 R310 R311 R312 R313 R314 R315 R321 R322 R323 R324 R335 R336 R337 R338 R339 R340 R341 R342 R343 R344 R345 R346 R347 R348 R349 R350 R351 R352 R353 R354 R355 R357 R358 R358 R359 R360 R361 R362 R363 R364 R365 R366 R367 R368 R369 S301 S302 S303 B-1 B-7 A-5 B-6 B-6 A-7 A-5 A-5 B-5 A-5 B-6 B-6 B-4 B-3 D-8 D-8 A-7 B-5 A-6 A-5 B-5 A-5 C-1 B-7 B-8 B-2 C-8 C-8 C-8 C-8 C-2 C-7 C-2 C-2 C-2 C-2 D-7 C-7 D-8 D-2 D-2 D-2 D-2 C-7 D-2 D-2 D-2 D-2 D-2 D-2 C-7 C-7 D-2 D-2 D-2 C-2 C-2 C-2 C-2 D-2 C-2 D-1 D-7 C-6

CN301 B-6 CN302 B-7 CN303 B-5 D301 D302 D303 D305 D307 D308 D309 D321 D322 D323 F301 IC301 IC322 A-3 A-3 B-2 B-4 D-2 B-4 A-3 C-1 A-2 A-7 A-6 A-4 C-7

(TR913E)VF-129 (B/W EVF) CD-209 (CCD IMAGER) VL-25 (VIDEO LIGHT)

(TR950E)VF-126 (COLOR EVF) CD-209 (CCD IMAGER) VL-25 (VIDEO LIGHT)

For printed wiring boards Chip parts TransistorC

B

E

There are few cases that the part printed on this diagram isnt mounted in this model.DD-117 (DC/DC CONVERTER) MA-353 STEREO MIC AMP, LASER LINK DD-117 (DC/DC CONVERTER) MA-353 STEREO MIC AMP, LASER LINK

PJ-94 (AV IN/OUT) SE-85 (STEADY SHOT)

PJ-94 (AV IN/OUT) SE-85 (STEADY SHOT)

STEREO MIC AMP, LASER LINKMA-353

4-55

4-56

CCD-TR913E/TR950E

4-57

4-58

4-59

STEREO MIC AMP, LASER LINKMA-353

CCD-TR913E/TR950E

VF-126 (COLOR EVF) PRINTED WIRING BOARD Ref. No. VF-126 Board; 20,000 Series VF-126 BOARDC4501 C4502 C4503 C4504 C4505 C4506 C4507 C4508 C4509 C4510 C4511 C4512 C4513 C4514 C4515 C4516 C4517 C4601 C4602 C4603 C4604 C4605 C4606 C4607 C4608 C4609 C4610 C4611 C4612 C4613 C4614 C4615 C4616 C4617 C4618 C4619 C4620 C4621 C4622 C4623 C4624 C4625 C4626 C4801 C4802 C4803 C4804 A-7 A-2 A-8 A-8 A-8 A-8 A-8 B-8 B-7 B-8 B-8 B-1 B-2 B-7 A-7 B-8 B-8 D-8 C-2 D-8 D-8 D-2 D-1 D-1 D-8 D-8 C-7 D-8 D-2 D-1 D-1 D-1 D-1 D-2 D-1 D-2 D-2 D-7 D-2 D-2 D-7 D-7 C-7 E-6 E-5 E-5 E-6 D4601 D4602 D4801 D4802 IC4501 IC4502 IC4601 IC4602 IC4603 L4501 L4502 L4601 L4602 L4603 L4801 L4802 D-8 D-1 E-4 F-6 A-8 A-1 D-1 D-7 D-8 A-2 B-7 C-7 C-1 D-8 E-6 E-5 R4524 R4525 R4526 R4528 R4602 R4604 R4605 R4606 R4607 R4608 R4609 R4610 R4611 R4612 R4613 R4614 R4615 R4616 R4617 R4618 R4619 R4620 R4621 R4622 R4623 R4624 R4625 R4626 R4627 R4629 R4630 R4631 R4632 R4634 R4635 R4636 R4637 R4638 R4638 R4639 R4801 R4802 T4801 B-8 B-8 B-8 A-7 D-8 D-8 D-8 D-1 D-8 D-2 D-8 D-8 D-1 D-1 D-8 D-8 D-8 D-1 D-2 D-2 D-7 E-1 D-2 D-2 D-2 D-2 D-2 D-2 D-2 D-2 D-1 D-1 D-1 D-1 D-8 D-8 D-8 D-1 D-8 D-8 E-6 E-6 F-5

VF-126 BOARDCAMERA REC/PB

1 IC4501 8

8 IC4502 @2.8Vp-p

H

0.55Vp-p

H

2 IC4501 9

9 IC4502 $

ND4801 E-4 Q4501 Q4601 Q4602 Q4603 Q4604 Q4605 Q4801 R4501 R4502 R4503 R4504 R4505 R4506 R4507 R4508 R4509 R4510 R4511 R4512 R4513 R4514 R4515 R4516 R4517 R4518 R4519 R4520 R4521 R4522 A-1 C-2 C-1 C-2 C-1 D-1 F-6 A-1 A-1 A-8 A-7 A-7 A-7 A-7 A-7 A-9 A-7 A-7 A-8 A-7 A-7 A-7 A-7 A-7 B-7 B-7 A-7 B-7 A-7

H

0.3Vp-p

11MHz

2.3Vp-p

3 IC4501 !

! IC4502 $2.8Vp-p

0.3Vp-p H

V

4 IC4501 @

2H

8.0Vp-p

5 IC4501 @8.0Vp-p

CN4501 A-1 CN4602 D-2

2H

(TR950E)VF-126 (COLOR EVF) CD-209 (CCD IMAGER) VL-25 (VIDEO LIGHT)

For printed wiring boards This board is four-layer print board. However, the patterns of layers two and three have not been included in the diagram. Chip parts TransistorC

6 IC4501 @8.0Vp-p

Diode32H

BDD-117 (DC/DC CONVERTER) MA-353 STEREO MIC AMP, LASER LINK

E

2

1

7 IC4601 !

PJ-94 (AV IN/OUT) SE-85 (STEADY SHOT)

There are few cases that the part printed on this diagram isnt mounted in this model.

11.0Vp-p H

COLOR EVFVF-126

4-60

4-61

4-62

CCD-TR913E/TR950E

4-63

4-64

4-65

COLOR EVFVF-126

CCD-TR913E/TR950E

CCD-TR913E/TR950E

CONTROL SWITCH BLOCKFK-8500/SS-8500

4-68

CCD-TR913E/TR950E

VF-129 (B/W EVF) PRINTED WIRING BOARD Ref. No. VF-129 Board; 3,000 Series VF-129 BOARDC901 C902 C903 C904 C905 C906 C907 C908 C909 C910 C911 C912 C913 C914 C915 C916 A-3 A-3 A-2 B-2 A-3 A-2 A-1 C-2 B-1 C-3 C-3 B-3 A-2 D-3 E-3 C-3 R905 R906 R907 R908 R909 R910 R911 R912 R913 R914 R915 R916 R917 R918 R919 R920 R921 R922 R923 R924 R925 R926 R927 R928 R929 R930 R931 R932 A-2 A-2 B-1 B-2 B-2 B-2 A-3 A-2 C-2 C-2 B-1 A-1 A-1 C-2 C-2 C-2 D-2 E-1 E-3 C-3 C-3 D-2 B-1 B-1 A-1 C-1 C-1 C-1

VF-129 BOARDCAMERA REC/PB

1 IC901 1,5

2.0Vp-p 20 msec

2 IC901 3

CN901 B-3 CN902 B-1 D901 D903 IC901 L901 L902 L903 Q901 Q902 Q903 Q904 R901 R902 R903 R904 A-1 D-3 A-1 B-1 B-3 D-1 A-2 B-2 C-3 C-2 A-3 A-3 A-1 A-3

2.0Vp-p 20 msec

3 IC901 7

RV903 C-2 RV904 D-120 msec

1.1Vp-p

T901 T902 TH901 W901

D-1 D-1 B-2 D-2

4 IC901 !

0.9Vp-p H

5 IC901 !

1.1Vp-p H

6 IC901 !

(TR913E)VF-129 (B/W EVF) CD-209 (CCD IMAGER) VL-25 (VIDEO LIGHT)

2.4Vp-p

For printed wiring boards Chip parts TransistorC

H

B

E

DD-117 (DC/DC CONVERTER)

There are few cases that the part printed on this diagram isnt mounted in this model.MA-353 STEREO MIC AMP, LASER LINK

PJ-94 (AV IN/OUT) SE-85 (STEADY SHOT)

4-69

4-70

4-71

B/W EVFVF-129

CCD-TR913E/TR950E

CF-58 (USER CONTROL) PRINTED WIRING BOARD Ref. No. CF-58 Board; 2,000 Series

For printed wiring boards Chip parts TransistorC

CF-58 BOARDBH001 B-12 R003 R005 R006 R007 R008 R009 R011 R012 R013 R014 R018 R020 R022 R023 R025 R028 R029 R031 R032 R036 R037 R038 R039 R040 R041 R042 R043 R044 R045 R046 C-6 B-15 B-15 B-15 D-15 D-15 C-5 C-5 B-5 B-2 B-4 C-4 B-4 B-4 B-2 C-4 B-4 C-2 C-15 B-4 C-15 C-2 B-4 C-15 B-1 C-4 C-4 D-6 C-6 C-15 R049 R050 R051 R052 R053 S001 S003 S004 S006 S008 S010 S012 S015 S017 S018 S021 S024 S027 D-6 D-6 D-6 D-6 B-1 B-5 D-7 B-6 B-7 C-7 C-10 D-10 B-8 B-1 B-3 D-8 A-15 C-1

Diode3

BZ001 BZ002 C001 C002 C003 CN001 CN002 CN003 CN007 CN008 CN010 D003 D004 D005 D006 D007 D008 D012 D013 IC001

C-16 C-16 B-6 B-6 C-5 D-13 A-17 D-5 D14 D-14 D-15 D-8 B-6 B-6 B-6 B-7 B-6 A-1 C-6 C-5 D-3 D-6 C-6

B

E

2

1

There are few cases that the part printed on this diagram isnt mounted in this model.(TR913E/TR950E)CF-58 (USER CONTROL)

VC-214 CAMERA PROCESSOR, Y/C PROCESSOR, FOCUS/ZOOM MOTOR DRIVE, REC/PB HEAD AMP, VIDEO/INTERFACE, IR TRANSMITTER, MODE CONTROL, SERVO, HI CONTROL, SYSTEM CONTROL, AUDIO PROCESSOR

Q001 Q003 Q005

USER CONTROLCF-58/MR-8500

4-72

4-73

4-74

CCD-TR913E/TR950E

4-75

4-76

4-77

USER CONTROLCF-58/MR-8500

CCD-TR913E/TR950E

DD-117 (DC/DC CONVERTER) PRINTED WIRING BOARD Ref. No. DD-117 Board; 2,000 Series DD-117 BOARDC801 C802 C803 C804 C805 C806 C807 C808 C809 C810 C811 C812 C813 C814 C815 C816 C817 C818 C819 C820 C821 C822 C823 C824 C825 C826 C827 C828 C829 C830 C831 C832 C833 C834 C836 C837 C838 C840 C841 C842 C843 C844 C846 C847 C848 C849 C850 C851 C852 C853 C854 C855 C856 C857 C860 C861 C862 C863 C864 C865 C866 C867 C868 C869 C870 C871 C872 C873 C874 C875 C876 C877 C878 CN801 CN931 CN933 CN934 CN935 CN936DD-117 (DC/DC CONVERTER) MA-353 STEREO MIC AMP, LASER LINK DD-117 (DC/DC CONVERTER) MA-353 STEREO MIC AMP, LASER LINK

For printed wiring boards This board is four-layer print board. However, the patterns of layers two and three have not been included in the diagram. Chip parts TransistorC 65 4

B

E

12 3

There are few cases that the part printed on this diagram isnt mounted in this model.(TR913E)VF-129 (B/W EVF) CD-209 (CCD IMAGER) VL-25 (VIDEO LIGHT)

(TR950E)VF-126 (COLOR EVF) CD-209 (CCD IMAGER) VL-25 (VIDEO LIGHT)

E-8 E-8 D-7 E-7 D-7 E-7 D-7 D-8 D-7 D-8 D-7 D-8 D-7 E-3 C-8 E-4 E-4 F-8 C-7 C-7 C-7 E-4 C-8 C-7 B-7 D-4 E-7 E-6 E-6 D-7 E-7 B-7 B-7 C-8 B-7 C-7 C-7 D-3 B-8 A-1 B-8 A-8 B-8 B-2 B-3 A-7 A-8 B-8 B-3 B-3 B-8 A-7 E-7 A-7 A-1 A-2 A-6 B-1 B-2 A-1 A-1 A-2 A-1 A-1 E-7 B-6 F-8 A-6 A-3 A-7 D-2 D-2 B-7 C-1 C-9 A-9 D-4 G-3 F-1

D806 D809 D810 D812 D813 D814 D815 D816 D817 D818 D819 D820 D821 D822 D932 D933 D934 D935 D936 D938 FB931 FB932 FB933 IC801 IC802 L801 L802 L803 L804 L805 L806 L807 L808 L809 L810 L811 L812 L813 L814 L815 L816 L817 L818 L819 L820 L821 L822 LF801 PS801 PS802 PS803 PS804 PS805 PS806 PS807 Q801 Q803 Q804 Q805 Q806 Q807 Q808 Q809 Q810 Q812 Q813 Q814 Q815 Q817 Q819 Q820 Q823 Q824 Q826 Q827

B-7 B-2 B-7 B-7 C-8 F-9 F-8 E-8 C-8 D-6 E-7 B-2 B-2 F-8 G-7 F-8 G-7 F-8 G-7 E-4 D-4 E-4 D-4 D-7 E-7 D-2 D-3 D-3 E-4 B-3 C-3 C-2 B-3 C-3 B-8 B-8 B-8 B-8 A-7 A-7 B-8 A-8 A-7 A-8 D-3 A-1 A-6 D-2 F-8 F-7 F-7 F-7 F-7 F-7 F-8 F-8 E-8 F-8 F-8 C-6 C-8 C-8 B-7 C-7 C-8 C-7 C-7 C-7 C-7 D-4 E-7 B-7 E-7 A-3 A-7

Q828 Q829 Q830 Q831 Q832 Q833 Q834 Q835 Q836 Q837 Q838 Q839 Q840 Q841 Q842 Q843 Q844 Q845 Q846 Q847 Q848 Q849 Q850 Q851 Q852 Q853 Q854 Q855 Q856 Q932 Q933 Q934 R801 R802 R803 R804 R805 R806 R807 R808 R809 R810 R811 R812 R813 R814 R815 R816 R817 R818 R819 R820 R821 R822 R824 R825 R826 R827 R828 R829 R830 R831 R832 R833 R834 R835 R836 R837 R838 R839 R840 R841 R842 R843 R844 R845 R846 R847 R849 R850

B-1 A-1 B-2 A-2 B-1 A-7 B-1 A-3 A-4 A-2 A-3 A-4 A-3 A-2 A-2 A-2 A-4 A-3 A-2 A-2 A-3 A-3 A-3 E-8 B-6 B-7 B-7 B-7 A-1 G-8 G-8 G-8 E-7 D-8 D-8 D-8 D-7 E-7 D-7 D-8 D-8 D-7 D-7 D-7 F-8 D-8 D-8 D-8 D-8 D-7 D-7 D-8 D-7 E-8 D-7 D-8 D-8 E-8 E-8 D-7 D-7 F-8 D-8 D-7 D-7 D-8 D-8 D-7 D-8 C-7 C-8 C-8 E-6 C-7 D-2 D-6 D-2 E-7 E-6 E-6

R852 R853 R854 R859 R864 R865 R866 R867 R868 R870 R871 R872 R873 R874 R875 R876 R877 R878 R879 R880 R881 R882 R883 R884 R885 R887 R888 R889 R890 R891 R892 R893 R894 R895 R896 R897 R898 R899 R900 R901 R902 R903 R904 R905 R906 R907 R908 R910 R911 R912 R913 R914 R915 R916 R917 R918 R919 R920 R921 R922 R923 R924 R925 R926 R932 R933 R934 R935 R936 R937 R938 R939 R940 R941 R942 R943 R944 R945 T801

D-6 D-6 D-6 E-7 E-7 B-7 B-7 E-7 A-6 A-3 A-3 B-2 A-1 B-1 A-6 B-1 A-3 A-7 B-1 B-1 B-1 B-1 B-3 B-4 A-2 B-3 B-3 A-2 A-2 A-3 A-3 A-3 A-2 A-1 A-4 A-4 A-2 A-2 A-2 A-1 A-1 A-3 A-3 A-3 A-3 A-3 B-7 B-7 B-7 B-7 F-8 D-7 E-6 A-2 A-3 A-6 A-2 A-2 D-3 D-2 D-3 B-1 A-4 C-9 G-8 F-2 F-2 F-2 F-2 F-2 F-2 F-2 G-8 G-8 E-4 G-7 B-1 B-1 B-2

PJ-94 (AV IN/OUT) SE-85 (STEADY SHOT)

PJ-94 (AV IN/OUT) SE-85 (STEADY SHOT)

DC/DC CONVERTERDD-117

4-78

4-79

4-80

CCD-TR913E/TR950E

DD-117 BOARDCAMERA REC/PB

1 IC801 4

0.75Vp-p 2 sec

2 IC801 ^

0.75Vp-p 2 sec

4-81

4-82

4-83

4-84E

DC/DC CONVERTERDD-117

SECTION 5 ADJUSTMENTS5-1. CAMERA SECTION ADJUSTMENT1-1. PREPARATIONS BEFORE ADJUSTMENT (CAMERA SECTION)1-1-1. List of Service Tools Oscilloscope Color monitor Regulated power supply Digital voltmeter Ref. No. J-1 J-2 J-3 J-4 J-5 J-6 J-7 J-8 J-9 J-10 J-11 J-12 J-13 Name Filter for color temperature correction (C14) ND filter 1.0 ND filter 0.3 Pattern box PTB-450 Color chart for pattern box Vectorscope Parts Code

CCD-TR913E/TR950E

Usage Auto white balance adjustment/check J-6080-058-A White balance adjustment/check J-6080-808-A White balance check J-6080-818-A White balance check J-6082-200-A J-6020-250-A

Adjustment remote commander (RM-95 upgraded). J-6082-053-B (Note 2) Siemens star chart J-6080-875-A For checking the flange back Clear chart for pattern box CPC-7 jig Power cord (Note 2) AFM DEV jig Extension cable (16P, 0.5mm) Extension cable (70P, 0.5mm) IR receiver jig J-6080-621-A J-6082-382-A For adjusting the video section For adjusting the color viewfinder section

J-6082-223-A For connecting the battery terminal and DC power supply J-6082-312-A For adjusting the deviation For extension between the CD-209 board (CN1401) and the VC-214 board (CN501) For extension between the DD-117 board (CN931) and J-6082-439-A the VC-214 board (CN914) J-6082-357-A J-6082-383-A For adjusting the IR transmitterNote 2: Connect the adjustment remote commander to the LANC jack, and set to HOLD switch to the ADJ side.

Note 1: If the micro processor IC in the adjustment remote commander is not the new micro processor (UPD7503G-C56-12), the pages cannot be switched. In this case, replace with the new micro processor (8-759-148-35).

J-1

J-2

J-3

J-4

J-5

J-6

J-7

J-8

J-9

J-10

J-11

J-12

J-13

Fig. 5-1-1.

5-1

1-1-2. Adjusting items when replacing main parts When replacing main parts, adjust the items indicated by r in the following table.Note 1 : Color EVF model (CCD-TR950E) only Note 2 : B/W EVF model (CCD-TR913E) only Replaced parts VF-126 board IC4501 (LCD driver)(Note 1) VF-126 board IC4602 (Timing generator) (Note 1) VF-126 board IC4601 (Backlight driver) (Note 1) B/W EVF block V901 (Picture tube)(Note 2) r r r r r r VF-126 board ND4801 (Fluorescent tube) (Note 1) Color EVF block LCD901 (LCD panel) (Note 1) r r r r r r r r r r r r r r r r r r r r r r r r r r r r r r r r r r r r r VF-129 board IC901 (CRT driver)(Note 2) VF-129 board T901 (FBT)(Note 2) Mechanism deck M901 (Drum assembly) Mechanism deck M902 (Capstan motor) VC-214 board IC501 (Timing generator) VC-214 board IC502 (S/H, AGC) r r r r r r

VC-214 board IC202 (Y, C process) VC-214 board IC151 (Y, C IN/OUT) VC-214 board IC001 (REC/PB AMP)

VC-214 board IC751 (IR transmitter) VC-214 board IC301 (AFM process)

Lens device CD-209 board IC1401 (CCD imager)

SE-85 board SE451 (Pitch sensor) SE-85 board SE452 (Yaw sensor)

Adjustment Section

Adjustment

Camera

Color EVF (Note 1)

B/W EVF (Note 2)

System Control Servo

Video

IR

Audio Mechanism

Initialization of D, E, F page data HALL adj. r Flange back adj. r r AGC gain calibration adj. r Color reproduction adj. r IRIS IN/OUT adj. r r MAX GAIN adj. r Auto white balance standard data input r Auto white balance adj. r Angular velocity sensor sensitivity preset r r and steady shot check Color EVF initial data input VCO adj. Bright adj. Contrast adj. Backlight consumption current adj. White balance adj. Centering adj. Focus adj. Aberration adj. Horizontal amplitude adj. Vertical amplitude adj. Brightness adj. Battery end adj. CAP FG offset adj. Switching position adj. 28MHz origin oscillation adj. r AFC f0 adj. r Filter f0 adj. r Y OUT level adj. r r C OUT level adj. r r RP filter f0 adj. r REC Y current adj. r r REC L level adj. r r REC C current adj. r r IR video carrier frequency adj. r r IR video deviation adj. r r IR audio deviation adj. r 1.5MHz deviation adj. r 1.7MHz deviation adj. r BPF f0 adj. r Tape path adj.

r r r r r r r r r r r r r r r r

VC-214 board IC401 (EEPROM)

r r r r r

Table. 5-1-1.

5-2

1-1-3. PreparationsNote 1: For details of how remove the cabinet and boards, refer to 2. DISASSEMBLY. Note 2: When performing only the adjustments, the lens block and boards need not be disassembled.

Pattern box

1) 2)

Connect the equipment for adjustments according to Fig. 5-1-3. By setting the Forced Camera Power ON mode, the camera power can be turned ON even if the front panel block (MA353 board, power switch, microphone unit) has been removed. When removing the front panel block disconnect the following connector. 1. VC-214 board CN903 (20P 0.5mm)

1.5 m

Note 3: As removing the cabinet (R) (removing the VC-214 board CN911) means removing the lithium 3V power supply (CF-58 board BH001), data such as date, time, user-set menus will be lost. After completing adjustments, reset these data. If the cabinet (R) has been removed, the self-diagnosis data, data on history of use (total drum rotation time, etc. ) will be lost. Before removing, note down the self-diagnosis data and data on history use (data of page: 2, address: A2 to AA). (Refer to SELF-DIAGNOSIS FUNCTION for the self-diagnosis data, and to 5-4. Service Mode for the data on the history use.) Note 4: Setting the Forced Camera Power ON Mode 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 10, set data: 01, and press the PAUSE button of the adjustment remote commander. The above procedure will enable the camera power to be turned on with the front panel block removed. After completing adjustments, be sure to exit the Forced Camera Power ON Mode. Note 5: Exiting the Forced Camera Power ON Mode 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 10, set data: 00, and press the PAUSE button of the adjustment remote commander. 3) Select page: 0, address: 01, and set data: 00.

Front of the lens

Fig. 5-1-2.

5-3

Note: Press the battery switch of the battery terminal using adhesive tape, etc.

Color monitor

Vector scope Terminated at 75 Need not connected Regulated power supply (Note) (8.4 0.1Vdc)

Lens block

CD-209 board CN1401 Battery terminal Adjustment remote commander

Extension cable (16P, 0.5mm) (J-6082-357-A)

Front panel block

Battery switch Need not connectedCN551 CN909 CN501 CN910

DC IN jack

CN935 CN936

Need not connected

LANC jack

VC-214 boardCN911 CN904 CN903 CN901 CN905 CN001

CN914

CN931

CN906 CN908

CN801

CN934

VIDEO jack PJ-94 board CN101

DD-117 board

Cabinet (L)

SE-85 board CN451 MA-353 board CN303

Must be connected when performing the video system and color viewfinder system adjustments.Extension cable (70P, 0.5mm) (J-6082-439-A) To CF-58 board CN001

CPC-7 jig (J-6082-382-A)

Cabinet (R)

Fig. 5-1-3.

5-4

1-1-4. Precaution 1. Setting the Switch Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette. 1. 2. 3. 4. 5. 6. POWER switch (MA-353 board) ........................... CAMERA NIGHT SHOT switch (Lens block) ................................. OFF VIDEO LIGHT switch (MA-353 board) ......................... OFF DEMO MODE (Menu display) ....................................... OFF DIGITAL ZOOM (Menu display) ................................... OFF STEADY SHOT (Menu display) ..................................... OFF 7. 8. 9. 10. 11. 12. FOCUS switch (MR-8500 block) ......................... MANUAL PROGRAM AE (CF-58 board) ....................................... Auto BACK LIGHT (CF-58 board) .......................................... OFF PICTURE EFFECT (CF-58 board) ................................. OFF DIGITAL EFFECT (CF-58 board) .................................. OFF 16 : 9 WIDE (MENU display) ......................................... OFF

2. Order of Adjustments Basically carry out adjustments in the order given.

Color bar chart (Color reproduction adjustment frame)Yellow Cyan Green White Magenta Red

Electronic beam scanning frame

H

CBlue

C=D

DYellow Cyan Green White Magenta Red Blue

CRT picture frame

A B

A=B

B A Enlargement

VFig. b (monitor TV picture)

Fig. a (VIDEO IN/OUT terminal output waveform)

Difference in levelAdjust the camera zoom and direction to obtain the output waveform shown in Fig. a and the monitor TV display shown in Fig. b.

B

A

Fig. 5-1-4.

3. Subjects 1) Color bar chart (Color reproduction adjustment frame) When performing adjustments using the color bar chart, adjust the picture frame as shown in Fig. 5-1-4. (Color reproduction adjustment frame) 2) Clear chart (Color reproduction adjustment frame) Remove the color bar chart from the pattern box and insert a clear chart in its place. (Do not perform zoom operations during this time.) 3) Flange back adjustment chart Make the chart shown in Fig. 5-1-5. using A0 size (1189mm 841mm) black and white vellum paper.

White 841mm Black

1189mm

Fig. 5-1-5.

Note: Use matte vellum paper bigger than A0, and make sure the edges of the black and white paper joined together are not rough.

5-5

1-2. INITIALIZATION OF D, E, F PAGE DATA1. Initializing the D,E,F Page DataNote: If the D,E,F page data has been initialized, Modification of D, E, F Page Data and all adjustments need to be performed again.

3. D Page TableNote : Fixed data-1 : Initialized data. (Refer to 1. Initializing the D,E,F Page Data.) Fixed data-2 : Modified data. (Refer to 2. Modification of D, E, F Page Data.)

Adjusting Page Adjusting Address Adjusting Page Adjusting Address Adjusting Page Adjusting Address

D 00 to 6F F 00 to FF E 00 to FF

Address 00 to 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F

Initial value 00

Remark

Test mode Fixed data-1 (Initialized data)

Initializing Method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 6, address: 00, and set data: 51. 3) Select page: 6, address: 01, set data: 51, and press the PAUSE button of the adjustment remote commander. 4) Select page: 6, address: 02, and check that the data is 01. 5) Select page: 2, address: 00, and set data: 29. 6) Select page: 2, address: 01, set data: 29, and press the PAUSE button of the adjustment remote commander. 7) Perform Modification of D,E,F Page Data. 2. Modification of D, E, F Page Data If the D, E, F page data has been initialized, change the data of the Fixed data-2 address shown in the following tables by manual input. Modifying Method: 1) Before changing the data, select page: 0, address: 01, and set data: 01. 2) New data for changing are not shown in the tables because they are different in destination. When changing the data, copy the data built in the same model.Note: If copy the data built in the different model, the camcorder may not operate.

Fixed data-2 (Modified data, copy the data built in the same model.) Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 (Initialized data)

3)

4) 5)

When changing the data, press the PAUSE button of the adjustment remote commander each time when setting new data to write the data in the non-volatile memory. Check that the data of adjustment addresses is the initial value. If not, change the data to the initial value. After completing Modification of D, E, F Page Data, select page: 0, address: 01, and set data: 00. Also perform all adjustments.

Fixed data-2 (Modified data, copy the data built in the same model.) Fixed data-1 Fixed data-2 (Modified data, copy the data built in the same model.) Battery end adj.

88 8D A8 BD C8

Fixed data-1 Fixed data-2 (Modified data, copy the data built in the same model.)

Fixed data-1

5-6

Address 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5D 5E 5F 60 61 62 63 64 65 66 67 68 69 6A 6B 6C 6D 6E 6F

Initial value Fixed data-2

Remark

4. F Page tableNote : Fixed data-1 : Initialized data. (Refer to 1. Initializing the D,E,F Page Data.) Fixed data-2 : Modified data. (Refer to 2. Modification of D, E, F Page Data.)

Fixed data-1 Fixed data-2 Fixed data-1 (Initialized data)

Address 00 to 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 40 41 42

Initial value 00 00 00 00 00 00 00 00 00 00 00 00

Remark

Emergency memory address

Fixed data-2

Fixed data-1 Fixed data-2 Fixed data-1 (Initialized data)

Fixed data-1 Fixed data-2 Fixed data-1 (Initialized data)

47 80 A0 80 2B 80 65 80

Fixed data-2 AGC gain calibration adj.

AWB standard data input

Table. 5-1-2.

1C 03 25 24 11 05 0A 00 8C

Fixed data-1 (Initialized data) Flange back adj.

Switching position adj. 28MHz origin osc. adj. Fixed data-1 (Initialized data)

5-7

Address 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5D 5E 5F 60 61 62 63 64 65 66 67 68 69 6A 6B 6C 6D 6E 6F 70 71 72 73 74 75 76 77 78 79 7A

Initial value

Remark Fixed data-1 (Initialized data)

Address 7B 7C 7D 7E 7F 80 81 82 83 84 85 86 87 88 89 8A 8B 8C 8D 8E 8F 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9E 9F A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF B0 B1 B2

84 68 08

HALL adj. Max gain adj. Fixed data-1 (Initialized data)

33 34

Color reproduction adj. Fixed data-1 Color reproduction adj. Fixed data-1 (Initialized data) Auto white balance adj. IRIS IN/OUT adj. Fixed data-1 (Initialized data) Flange back adj.

Remark Initial value C0 REC L level adj. C0 C0 C0 7C 7C 7C 7C 96 96 80 REC C current adj. Fixed data-1 (Initialized data)

8D 87 41 49

Fixed data-2 Fixed data-1 (Initialized data)

2A 00 19 00 37 76 63 83 7A 8D 7A 41 33 C7 6B 40 9A 7B 60

Fixed data-2 Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 (Initialized data)

Angular velocity sensor sensitivity preset and steady shot check. CAP FG offset adj. 1.5MHz deviation adj. 1.7MHz deviation adj. BPF f0 adj. Fixed data-1 IR video deviation adj. IR audio deviation adj. IR video carrier freq. adj. Y OUT level adj. AFC f0 adj. C OUT level adj. Fixed data-1 Filter f0 adj. RP filter f0 adj. Fixed data-1 (Initialized data)

Fixed data-2 Fixed data-1 (Initialized data)

70 70 70 70 63 6B 63 6B

REC Y current adj.

5-8

Address B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA

Initial value

Remark Fixed data-1 (Initialized data)

Address EB EC ED EE EF F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF

Initial value

Remark Fixed data-2 Fixed data-1 (Initialized data)

00 00 02 FC F2

Flange back adj.

Color reproduction adj. Fixed data-1 (Initialized data)

Table. 5-1-3.

Fixed data-2 (Modified data, copy the data built in the same model.) Fixed data-1

Fixed data-2 Fixed data-1 (Initialized data)

Fixed data-2 Fixed data-1

5-9

5. E Page TableNote : Fixed data-1 : Initialized data. (Refer to 1. Initializing the D,E,F Page Data.) Fixed data-2 : Modified data. (Refer to 2. Modification of D, E, F Page Data.)

Address 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5D 5E 5F 60 61 62 63 64 65 66 67 68 69 6A

Initial value

Remark Fixed data-1 (Initialized data)

Address 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32

Initial value

Remark Fixed data-1 (Initialized data)

Fixed data-2 Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 (Initialized data)

Fixed data-2 Fixed data-1 (Initialized data)

Fixed data-2 (Modified data, copy the data built in the same model.) Fixed data-1 Fixed data-2

Fixed data-2

5-10

Address 6B 6C 6D 6E 6F 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 7F 80 81 82 83 84 85 86 87 88 89 8A 8B 8C 8D 8E 8F 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9E 9F A0 A1 A2

Initial value Fixed data-2 Fixed data-1 Fixed data-2

Remark

Address A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF D0 D1 D2 D3 D4 D5 D6 D7

Initial value

Remark Fixed data-1 (Initialized data)

Fixed data-1 (Initialized data)

Fixed data-2 (Modified data, copy the data built in the same model.) Fixed data-1 (Initialized data)

70 77 80 80 80

Fixed data-2 (Modified data, copy the data built in the same model.) VCO adj. (Color EVF) Bright adj. (Color EVF) Contrast adj. (Color EVF) White balance adj. (Color EVF) Fixed data-2 Fixed data-1

90

Fixed data-2 Backlight consumption current adj. (Color EVF) Fixed data-1 (Initialized data)

5-11

Address D8 D9 DA DB DC DD DE DF E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF

Initial value

Remark Fixed data-1 (Initialized data)

A0

Fixed data-2 (Modified data, copy the data built in the same model.) Backlight consumption current adj. (Color EVF)

Table. 5-1-4.

5-12

1-3. CAMERA SYSTEM ADJUSTMENTSBefore perform the camera system adjustments, Check that the specified value of 28MHz Origin Oscillation Adjustment, Y OUT level Adjustment and C OUT level Adjustment of VIDEO SYSTEM ADJUSTMENT are satisfied. 1. HALL Adjustment For detecting the position of the lens iris, adjust the hall AMP gain and offset. Subject Not required Measurement Point Measuring Instrument Adjustment Page Adjustment Address Specified Value Display data of page 1 Adjustment remote commander F 47, 48 86 to 8A during IRIS OPEN 15 to 19 during IRIS CLOSE 2. Flange Back Adjustment The inner focus lens flange back adjustment is carried out automatically. In whichever case, the focus will be deviated during auto focusing/manual focusing. 2-1. Flange Back Adjustment(1) Subject Flange back adjustment chart (2.0 m from the front of the lens) (Luminance: 350 50 lux) Measurement Point Measuring Instrument Adjustment Page Adjustment Address Check operation on TV monitor F 38 to 3D, 5A to 5E, F8 to FA

Note : Displayed data of page 1 of the adjustment remote commander. 1 : 00 : XX Display data

Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 6, address: 01, set data: 6D, and press the PAUSE button of the adjustment remote commander. (The HALL adjustment is performed and the adjustment data is stored in page: F, address: 47 and 48.) 3) Select page: 6, address: 02, and check that the data is 01. 4) Select page: 6, address: 01, set data: 00, and press the PAUSE button. Checking method: 1) Select page: 0, address: 03, and set data: 03. 2) Select page: 6, address: 01, set data: 01, and press the PAUSE button. 3) Select page: 1, and check that the display data (Note) during IRIS OPEN satisfies the specified value. 4) Select page: 6, address: 01, set data: 03, and press the PAUSE button. 5) Select page: 1, and check that the display data during IRIS CLOSE satisfies the specified value. Processing after Completing Adjustments 1) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 2) Select page: 0, address: 01, and set data: 00. 3) Select page: 0, address: 03, and set data: 00.

Switch setting: 1) NIGHT SHOT .................................................................. OFF 2) DIGITAL ZOOM (Menu display) ................................... OFF 3) STEADY SHOT (Menu display) ..................................... OFF 4) VIDEO LIGHT ................................................................ OFF Adjusting method: 1) Check that at both the zoom lens TELE end and WIDE end, the center of the chart for the flange back adjustment and center of the exposure screen coincide. 2) Select page: 0, address: 01, and set data: 01. 3) Check that the data of page: F, address:38 to 3D, 5A to 5E, F8 to FA is the initial value (See table below). Address Data Address Data 38 1C 5B 00 39 03 5C 19 3A 25 5D 00 3B 24 5E 37 3C 11 F8 00 3D 05 F9 00 5A 2A FA 02 4) 5) 6) Select page: 6, address: 02, and check that the data is 00. Select page: 6, address: 01, set data: 13, and press the PAUSE button of the adjustment remote commander. Select page: 6, address: 01, set data: 15, and press the PAUSE button. (The adjustment data will be automatically input to page: F, addresses:38 to 3D, 5A to 5E, F8 to FA.) Select page: 6, address: 02, and check that the data is 01.

7)

Processing after Completing Adjustments 1) Turn OFF the main power supply (8.4V). 2) Perform Flange Back Adjustment (2).

5-13

2-2. Flange Back Adjustment (2) Perform this adjustment after performing Flange Back Adjustment (1). Subject Subject more than 500m away (Subjects with clear contrast such as buildings, etc.) Measurement Point Measuring Instrument Adjustment Page Adjustment Address Check operation on TV monitor F 38 to 3D,