Specialist Tools & Accessories · SPECIALIST TOOLS AND ACCESSORIES C342 CRIMPING TOOLS The crimping tools are supplied with OLED display, which provide essential real time tool operating

AU 133 122 CABAC.COM.AU NZ 0800 77 69 69 CABAC.CO.NZ

VOL20

Specialist Tools & Accessories

www.cabac.com.au | www.cabac.co.nz | Volume 18

Specialist Tools and Accessories1.5T Crimpers C3433T Crimpers C3435T Crimpers C34312 to 15T Crimpers and Crimp Heads C34423 to 25T Crimpers and Crimp Heads C34752 to 60T Crimpers and Crimp Heads C347Batteries and Accessories C348Cutters and Cutting Heads C349Electric and Hydraulic Pumps C352Hydraulic Punch Tool and Accessories C353Dies Copper C355Dies Earthing Copper C357Dies Indent Crimp C358Dies Aluminium C359Dies Aluminium Nest Crimp C360Dies Cutting C361Dies Insulink C361Adaptors C361Hydraulic Pole Saws C362

SPECIALIST TOOLS AND ACCESSORIES

C342

CRIMPING TOOLSThe crimping tools are supplied with OLED display, which provide essential real time tool operating information such as momentary force reached and maximum pre-set level (in Newtons, tons, PSI or bar). The OLED also displays the battery charge level, tool serial number, number of cycles performed and number of cycles before scheduled maintenance. An LED work light and service status light is displayed for assistance with maintenance. The Cembre 18V range is easy to manage during crimping with low operating noise and vibration aiding user comfort in addition to the ergonomic housing. A LED light is included for convenience and safety, enhancing vision in darker areas.

FEATURES:• Simple and basic operation with low vibration and noise

in addition to comfortable handling• 18V 4.0 Ah power system provides a 20-30%

improvement in cycle time and a 70-95% increase in the number of cycles

• OLED display provides real time operating information• USB interface and on-board memory provides

convenient logging• Heads rotate at various angles• Built in LED working light for dark areas• Battery charger and spare battery in kit

CUTTING TOOLS The Cembre 18V range is easy to manage during crimping with low operating noise and vibration aiding user comfort in addition to the ergonomic housing. An LED light is included for convenience and safety, enhancing vision in darker areas. The blades are manufactured from special high strength steel, ensuring long service life. The head rotates, adapting to the angle that the conductor is cut, especially in a confined space.

FEATURES:• Simple and basic operation with low vibration and noise

in addition to comfortable handling• 18V 4.0 Ah power system provides a 20-30%

improvement in cycle time and a 70-95% increase in the number of cycles power by one

• Head rotates at various angles (please see table) • Built in LED working light for dark areas• Battery charger and spare battery in kit

18V 4.0 AH BATTERY• Provides 100% of its energy between -15 °C and 50 °C• Electronic control of single cells to avoid over and under

charging• Air-cooled charging technology to increase battery life• Auto-off to optimise energy consumption• Built in LED charge level indicator• Tough and rugged housing

The Cembre range of 18V battery powered hydraulic tools are loaded with features. Based of the renowned Cembre 14V battery range of 13 ton tools, this range is suitable for crimping up to 400mm2 and cutting electrical cable up to 95mm in diameter.The new 18V 4.0 Ah lithium-ion battery offers a higher capacity than its predecessor the 14.4V 3 Ah. Greater crimping speed and crimping force is the result of a revitalised hydraulic system with double speed action, a more rapid approach of the dies or cutting blade to the connector or conductor and improved speed and control

of the crimping/cutting action. A maximum pressure sensor and security valve assures greater precision and repeatability of the pressure cycle with double the provision for operator safety.Crimping tools incorporate on-board memory for data logging up to 200 000 cycles which can be transferred to a PC by USB interface. This unique feature assists with logging work performance and ensuring the tool is in proper working condition.

18V CEMBRE CRIMPING AND CUTTING TOOLS


C343

Part No. B15MDT • Lightweight terminal crimper with a 1.5 tonne crimp capability• One hand operation with a head rotation of 340 degrees• Includes a moulded carry case with two batteries and a charger• Suitable for Copper terminals, lugs and splices up to 16 sq.mm• Requires suitable dies for pre or uninsulated bootlace ferrules

1.5T BATTERY CRIMPER 18VCRIMPERS 1.5T1.5T CRIMPERS

Unit: EA Qty: 1

Part No. B35-50MDT • Lightweight terminal crimper with a 3.5 tonne crimp capability• One hand operation with a head rotation of 180 degrees• Includes a moulded carry case with two batteries and a charger• Suited for Australian dimension Copper or Aluminium lugs or links• Uses standard M type (5 ton) dies up to 95mm2

3.5T BATTERY CRIMPER 18VCRIMPERS 3T3T CRIMPERS

Unit: EA Qty: 1

Part No. HT51 • Designed for the overhead linesman - this crimper is lightweight and can be operated with

one hand• Small enough to be carried in a tool pouch• Only three pumping operations required to complete crimp

5 TONNE HYDRAULIC CRIMPERHYDRAULIC CRIMPERS 5T5T CRIMPERS

Unit: EA Qty: 1

Part No. B500T • 18V battery powered 5 tonne, hydraulic crimping tool giving greater crimping speed and more

operations• Improved handling balance with low noise and vibration• Dies available for Copper lugs from 6 to 120 sq.mm• LCD condition indication displays crimping pressure• Data storage logging of crimping operations

5T BATTERY POWERED CRIMPER LI-IONBATTERY CRIMPERS 5T

Unit: EA Qty: 1

Part No. PA-6B • Pneumatic crimping head for electrical terminals, designed for flexible product operations• Large range of dies and replacement head/jaws available• Operated by foot air valve• Unit should be bench mounted using the attachment base

PNEUMATIC TERMINAL & LUG CRIMPER 5 TONNEPNEUMATIC CRIMPERS 5T

Unit: EA Qty: 1

Part No. PA-6BHD • Heavy Duty Pneumatic Terminal and Lug Crimper for flexible product operations• Machine jaws and a large range of dies also available• Operated by foot valve• Unit should be bench mounted using attachment

PNEUMATIC CRIMPING HEAD Unit: EA Qty: 1


C344

Part No. Y-PA6B JAWS • Spare part for PA-6B Pneumatic Terminal and Lug Crimper

PNEUMATIC CRIMPING MACHINE JAWS PA-6B Unit: EA Qty: 1

Part No. B1350-CT • 18V battery powered hydraulic 13 tonne crimping tool, allows for more crimps per charge at a

quicker pace• Balanced, low noise and vibration for better operator comfort• LCD condition display monitors the crimp pressure• Data logging of crimping cycles• Copper dies available up to 400mm2

13T BATTERY CRIMPER LI-IONBATTERY CRIMPERS 13T12 TO 15T CRIMPERS AND CRIMP HEADS

Unit: EA Qty: 1

Part No. B1350L-CT • 18V battery powered hydraulic 13 tonne crimping tool, allows for more crimps per charge at a


13T BATTERY CRIMPER LI-ION-LONG HEAD Unit: EA Qty: 1

Part No. B1350-UCT • 18V battery powered hydraulic 13 tonne crimping tool, allows for more crimps per charge at a


13T BATTERY CRIMPER LI-ION U HEAD Unit: EA Qty: 1

Part No. B1300-CT • 18V battery powered hydraulic 13 tonne crimping tool, allows for more crimps per charge at a


13T BATTERY CRIMPER LI-ION Unit: EA Qty: 1

Part No. B1300L-CT • 18V battery powered hydraulic 13 tonne crimping tool, allows for more crimps per charge at a


13T BATTERY CRIMPER LI-ION-LONG HEAD Unit: EA Qty: 1


C345

Part No. HT131-C • Quality manufacture and robust design will give years of trouble free service• 25mm throat opening• Two speed - saving time and effort during crimping• Head rotates 180 degrees for work in tight spaces

13 TONNE HYDRAULIC CRIMPER WITH C HEADHYDRAULIC CRIMPERS 13T

Unit: EA Qty: 1

Part No. HT131-C-WHO • Quality manufacture and robust design will give years of trouble free service• 25mm throat opening• Two speed - saving time and effort during crimping• Head rotates 180 degrees for work in tight spaces

HT131-C WITH FULL SET OF DIES 16-300MM2 Unit: EA Qty: 1

Part No. HT131-UC • Easy access to tight cable joints, particularly in a trench• Shorter handles ensure easier handling• Large throat opening• Supplied in a heavy-duty plastic carry case

13 TONNE U HEAD HYD. CRIMPER Unit: EA Qty: 1

Part No. HT131-UC-WHO • Easy access to tight cable joints, particularly in a trench• Shorter handles ensure easier handling• Large throat opening• Supplied in a heavy-duty plastic carry case

HT131-UC WITH FULL SET OF DIES 16-300MM2 Unit: EA Qty: 1

Part No. HT131L-C-WHO • Quality manufacture and robust design will give years of trouble free service• Nominal force of 13.3 tonnes at the die faces• Head rotates 180 degrees for work in tight spaces• Flexible and easy handling

HT131L-C WITH FULL SET OF DIES 16-300MM2 Unit: EA Qty: 1

Part No. HT131LN-C • Quality manufacture and robust design will give years of trouble free service• Head rotates 180 degrees for work in tight spaces• Two speed - saving time and effort during crimping• Supplied in a heavy-duty plastic carry case

13 TONNE C LONG HEAD HYD. CRIMPER Unit: EA Qty: 1


C346

Part No. Y-HT131-CASE • Spare case only• Case suits HT131 series hydraulic tools• Features compartments for dies and crimping tool• Colour: Cembre Blue

HT131-C STORAGE CASE HT131UC HT131L-CCRIMPER ACCESSORIES 13T

Unit: EA Qty: 1

Part No. AU130-C • Removable die holder for RHU131-C crimp head and HT131-UC crimp tool• Replacement part for holding Cembre 13 tonne C type dies• Fits tool head and locked with pin

C DIE ADAPTOR FOR RHU/UC Unit: EA Qty: 1

Part No. RHC131 • Remote head 13 tonne crimper to be used with a CABAC remote pump or any pump

developing 700 bar (10,000 psi) pressure• Use with standard CABAC 12 tonne dies• Standard ‘C’ throat and wide throat available• Not supplied with a case

13 TONNE REMOTE HEAD C TYPE 25MM THROATCRIMP HEADS 13T

Unit: EA Qty: 1

Part No. RHU131-C • Remote head 13 tonne crimper to be used with a CABAC remote pump or any pump

developing 700 bar (10,000 psi) pressure• Steel case for head and dies available (Part No. Y-RHC131 CASE)• Throat opening: 34mm• Weight: 3.7kg

13 TONNE REMOTE HEAD U TYPE Unit: EA Qty: 1

Part No. RHC131L-N • Remote head 13 tonne crimper to be used with a CABAC remote pump or any pump

developing 700 bar (10,000 psi) pressure• Use with standard CABAC 12 tonne dies• Standard ‘C’ throat and wide throat available• Not supplied with a case

13 TONNE REMOTE LONG HEAD C TYPE 42MM Unit: EA Qty: 1

Part No. CYO-510B • Economically priced 12 tonne tool with a two stage pumping action for reduced crimping time• 180 degree head rotation for work in tight spaces• Reinforced glass fibre handles• Supplied in a heavy-duty plastic carry case

ECONOMY 12T HYDRAULIC CRIMPER C HEADCRIMPERS 12T

Unit: EA Qty: 1


C347

Part No. ECW-H3D • 23 tonnes of force at the die face with the ability to crimp up to 630mm2 Copper and 500mm2

Aluminium• Light-weight - easily handled by one person• Couple with a CABAC hydraulic pump (700 bar)• Steel storage case supplied separately

23 TONNE CRIMPER - REMOTE HEADCRIMP HEADS 23T23 TO 25T CRIMPERS AND CRIMP HEADS

Unit: EA Qty: 1

Part No. Y-ECW-3D CASE • For use with the 23 tonne Hydraulic Crimper (Part No. ECW-H3D)• Die holder tray is also available

ECW-H3D STEEL STORAGE CASE Unit: EA Qty: 1

Part No. Y-ECW-3D D/HOLD • For use with the 23 tonne Hydraulic Crimper (Part No. ECW-H3D)• Steel storage case is also available

ECW-3D DIE HOLDER TRAY ONLY Unit: EA Qty: 1

Part No. RHU520 • Remote head 52 tonne crimper can be used with one of our hydraulic pumps or any pump

developing 700 bar (10,000 psi) pressure• Crimps Cu and Al lugs and compression fittings up to 1200mm2• Throat opening: 75mm• Weight: 18kg

HYD. PRESSHEAD WITH FEMALE COUPLERCRIMP HEADS 52T52 TO 60T CRIMPERS AND CRIMP HEADS

Unit: EA Qty: 1

Part No. RHU600 • Remote head 60 tonne can be used with hydraulic pumps developing 700bar (10,000psi)• Manufactured in thermally treated steel• Resistant to oxidation from external agents, abrasion and wear• Equipped with a quick fit hydraulic male coupler• Precision made for greater safety and reliability

HYDRAULIC CRIMPING HEAD 600KNCRIMPING HEAD 60T

Unit: EA Qty: 1


C348

Part No. CP1120-W-1000-KV • Cutter head and pump system to safely cut LV and MV cable in a network if the cable has not

been spiked• The cutter head is insulated from the pump• System must be rebuilt if a ‘live’ cable is cut• Earth connection available to ground/earth the head and the pump• Supplied in a metal case

HYDRAULIC CUTTING UNIT Unit: EA Qty: 1

Part No. Y-ESC600 • Vehicle battery cord for the 13 tonne battery powered hydraulic crimper• Suitable for B131-C and B131LN-C parts• Length: 6M

B131-C VEHICLE BATTERY CORD 6M WITH PLUGBATTERIES AND ACCESSORIESBATTERIES AND ACCESSORIES

Unit: EA Qty: 1

Part No. B131-C CARCHARGER • 12V cigarette lighter charger cord for the 13 tonne battery powered hydraulic crimper• Suitable for B131-C and B131LN-C parts

BATTERY CRIMPER 13T CAR CHARGER B131-C Unit: EA Qty: 1

Part No. DC1414 • 240V charger for the 13 tonne battery powered hydraulic crimper• Suitable for B131-C and B131LN-C parts

CHARGER TO SUIT CB1430H BATTERY Unit: EA Qty: 1

Part No. CB1430H • Compatible with select range of Cembre crimpers• Battery material: Ni-MH• Battery voltage: 14.4V• Battery current: 3 Ah

NI-MH 14.4V 3.0AH RECHARGEABLE BATTERY Unit: EA Qty: 1

Part No. CB1840L • Electronic control of single cells to avoid overcharging and undercharging• Air-cooled charging technology to increase battery life• Auto-off to optimise energy consumption• Battery charger also available (Part No. ASC30-36)

LI-ION 18V 4.0AH RECHARGEABLE BATTERY Unit: EA Qty: 1


C349

Part No. ASC30-36 • Battery charger for use with the Li-Ion 18V 4.0 Ah Rechargeable Battery (Part No. CB1840L)

CHARGER TO SUIT CB1840L BATTERY Unit: EA Qty: 1

Part No. TC04 • Remote hydraulic cutter head specifically designed to cut ACSR, Copper conductors/cables

and steel ropes, Copper, Aluminium and steel rods• Double stage hydraulic system saves time for the operator• Fits any pump with Quick Connect hydraulic fittings• Supplied in a steel case

REMOTE HYD.ST.WIRE ASCR 40MM ODCUTTERSCUTTERS AND CUTTING HEADS

Unit: EA Qty: 1

Part No. TC055 • Equipped with a quick automatic coupling for connection to Cembre hydraulic pumps with a

working pressure of 700bar• Designed to cut cables, steel rope, rods, armoured cable• Supplied in a metal case• See data sheet for cutting specifications

HYD. CUT TOOL HEAD CU/AL 55MM ACSR 50MM Unit: EA Qty: 1

Part No. TC085 • Remote hydraulic cable cutter head specifically designed to cut annealed Copper and

Aluminium conductors and telecom cables• Supplied with a steel case• Not suitable to cut steel and armoured cable• Maximum cutting diameter: 85mm

PUMP OPERATED CUTTER HEAD MAX DIA 85MM Unit: EA Qty: 1


Aluminium conductors and telecom cables• Supplied with a steel case• Not suitable for armoured cable• Maximum cutting diameter: 95mm



Aluminium conductors and telecom cables• Supplied with a steel case• Automatic safety valve to prevent over-pressure• Complete with 3/8 inch NPT self-lock male coupler• Not suitable to cut steel and armoured cable



C350

Part No. HT-TC026 • Hand operated hydraulic tool specifically designed to cut ACSR, Copper conductors/cables

and steel ropes, Copper, Aluminium and steel rods• Dual speed pump• Head can rotate 90 degrees• Supplied with a canvas bag• Maximum cutting diameter: 24mm

HYD. CUTTING TOOL ACSR/STEEL 24MM MAX OD Unit: EA Qty: 1

Part No. HT-TC055 • Hand operated hydraulic cable cutter specifically designed to cut steel and wire rope• Produces up to 140kN force at the max pressure of 808 bar• Suitable for Cu, Al, armoured cable, steel rope and rods• See data sheets for cutting specifications• Maximum cutting diameter: 55mm

HYD. CUTTING TOOL CU/AL 55MM MAX OD Unit: EA Qty: 1

Part No. HT-TC065 • Hand operated hydraulic cable cutter specifically designed to cut Copper, Aluminium and

telecom cables• Supplied in a canvas bag• Not suitable to cut steel and armoured cable• Maximum cutting diameter: 65mm

HYD. CUTTING TOOL AL/CU 65MM MAX OD Unit: EA Qty: 1

Part No. HT-TC0851 • Hand operated hydraulic cable cutter specifically designed to cut annealed Copper and

Aluminium conductors and telecom cables• Double stage hydraulic system saves time for the operator• Head can rotate 180 degrees• Supplied with a canvas bag• Maximum cutting diameter: 85mm

HYD. CUTTING TOOL CU/AL 85MM MAX OD Unit: EA Qty: 1

Part No. BTC250T • Battery powered cutter suitable for ACSR, steel rope, stay wire, steel rods and armoured

cable• 18V battery produces faster and more cutting operations• Head pivots up to 180 degrees - ease of use in confined spaces• Low noise and minimal vibration aid operator comfort• Lightweight and balanced for single handed operation

18V BATTERY CUTTER 25MM Unit: EA Qty: 1

Part No. BTC500T • Battery powered 18V cable cutter for Copper, Aluminium and telecom cables and conductors• Blades: High strength, heat treated special steel• Head pivots up to 90 degrees - ease of use in confined spaces• Low noise and minimal vibration aid operator comfort• Lightweight and balanced for single handed operation



C351

Part No. BTC550T • 18V battery powered for faster cutting operations. Lightweight and balanced for single handed

operation• Cutting blades: High strength, heat treated special steel• Head pivots up to 320 degrees - ease of use in confined spaces• Low noise and minimal vibration aid operator comfort• Cutter suitable for armoured cable, steel rope and rods


Part No. BTC650T • 18V battery powered for faster cutting operations for Aluminium, Copper and telecom cables• Cutting blades: High strength, heat treated special steel• Head pivots up to 335 degrees - ease of use in confined spaces• Low noise and minimal vibration aid operator comfort• Lightweight and balanced for single handed operation


Part No. BTC950T • 18V battery powered for faster cutting operations for Aluminium, Copper and telecom cables• Cutting blades: High strength, heat treated special steel• Head pivots up to 335 degrees - ease of use in confined spaces• Low noise and minimal vibration aid operator comfort• Lightweight and balanced for single handed operation



C352

Part No. CPC-30A • Economically priced - designed to cut cable with a shearing scissor action• Self contained hydraulic hand pump develops 6.7 tonnes• Head swivels for access into tight situations• Hardened steel blades specifically to cut ACSR

HYDRAULIC CUTTER - ECONOMY MAX 240MM2CUTTERS

Unit: EA Qty: 1

• Easy to use - designed to attach to a hand held electrical drill• Various cutting sizes available from 30-100mm diameter cable• Supplied in an easy to carry case• Blade can be sharpened using a file or mini grinder

Part No. Description Unit QtyDDQ33 CUTTER HEAD DIA. 22 MM STEEL ROPE EA 1DDQ30 CUTTER HEAD DIA. 30 MM ACSR CHAIN EA 1DDQ80 CUTTER HEAD DIA. 80 MM AL/CU CABLE EA 1

Part No. MSS-S40-M • Smallest and most powerful cutter weight to power ratio available on the market today• 2 speed hydraulic pumping for rapid advance and cutting

HYD. STEEL AND WIRE ROPE CUTTER 40MM MAX Unit: EA Qty: 1

Part No. MSS-S40-18V • Guillotine style for cutting Copper, Aluminium, ACSR and Steel Wire Rope up to 40mm O.D.• Rapid blade advance - double speed in cutting stage• Rotating head 180 degrees• Factory pre-set overload relief to protect tool

BATTERY POWERED CABLE CUTTER 40MM MAX Unit: EA Qty: 1

Part No. PO7000 • Double stage foot pump for faster crimping and cutting• Hands are free for cable and lug positioning• Maximum stability with an extra large base• Supplied in a robust steel case

HYD. FOOT PUMP 2 STAGE IN CASEPUMPSELECTRIC AND HYDRAULIC PUMPS

Unit: EA Qty: 1

Part No. B70M-P24 • A state of the art unit designed for mobile crimping and cutting - use with any of the CABAC

crimping heads and cutters• Light-weight and balanced - easy to carry• Powerful 24V battery with a 60 minute recharge• Manual pressure relief valve

BATTERY POWERED HYDRAULIC PUMP Unit: EA Qty: 1


C353

Part No. MSS-HCP-45SV • Suitable for use with all hydraulic remote crimping heads up to 60 tonne capacity• Light-weight, portable and small in size with high power• Audible ‘POP’ signals completion of the crimp cycle• Comes with remote control pendant• Double Acting pump available (Part No. MSS-HCP-45SV-DA)

CRIMPING PUMP -0.45KW-240V- 12V REMOTE Unit: EA Qty: 1

Part No. KSMP-3AR • Usable oil: 1.8 litres• First stage pressure: 15 bar at 2.0 l/min• Second stage pressure: 700 bar at 0.2 l/min• Power: 240V, 1.6A

ELECTRIC HYDRAULIC PUMP-240V Unit: EA Qty: 1

Part No. HPP1 • This pump is called the ‘Peanut Pump’ for good reason. Small and light-weight, this pump

produces a full 700bar (10,000 psi) pressure• Sufficient oil volume to power all CABAC crimp heads and cutters• Operate at any angle - no leaks if tipped over• Motor and pump are totally enclosed and drip proof• Comes with a 3m hose and coupler to suit Cabac and MSP hyd. tools

SUPER LIGHTWEIGHT 240V ELECTRIC PUMP Unit: EA Qty: 1

Part No. HPP2 • Two stage pumping with 2.5L/min flow in low pressure stage and 0.35L/min in the high

pressure stage• For CABAC and MSS remote crimp heads (up to 60 tonnes) and cutters• Power Supply Voltage: 240V/50Hz• Weight: 18kg• Comes with a 3m hose and coupler to suit Cabac and MSP hyd. tools

HYDRAULIC PUMP/HOSE 240V LIGHTWEIGHT Unit: EA Qty: 1

Part No. SKP-15 • A complete punch tool set including a pump and various dies for mild steel <3.2mm• Output of 15 tonnes and a ram stroke of 25mm• Round dies: dia. 22, 27.6, 34.1, 42.7, 48.7 and 60.5mm• Square die: 32x32mm• Additional dies and spindles also available separately

15 TONNE HYDRAULIC PUNCH DIE SETHYDRAULIC PUNCH DIE 15THYDRAULIC PUNCH TOOL AND ACCESSORIES

Unit: EA Qty: 1

Part No. PDS32 • Die for SKP-15 hydraulic punch tool set• Suitable for mild steel up 3.2mm thick• Die is not suitable for stainless steel• Round and square dies available for SKP-15

PUNCH DIE SQUARE 32 X 32MM W/SPINDLE Unit: EA Qty: 1


C354

Part No. PDSPINDLE • Spare part for the SKP-15 15 tonne Hydraulic Punch• A compact, light and fast punching tool• Full kit also available

PUNCH DIE SET SPINDLE Unit: EA Qty: 1

Part No. PDSPACER • Spare part for the SKP-15 15 tonne Hydraulic Punch• A compact, light and fast punching tool• Full kit also available

PUNCH DIE SET SPACER Unit: EA Qty: 1

• Die for SKP-15 hydraulic punch tool set• Suitable for mild steel up 3.2mm thick• Die not suitable for stainless steel• Round and square dies available for SKP-15

HYDRAULIC PUNCH DIE ACCESSORIES

Part No. Description Unit QtyPD16.2 PUNCH DIE ROUND 16.2MM EA 1PD20.4 PUNCH DIE ROUND 20.4MM EA 1PD22.5 PUNCH DIE ROUND 22.5MM EA 1PD25.4 PUNCH DIE ROUND 25.4MM EA 1PD32.5 PUNCH DIE ROUND 32.5MM EA 1PD40.5 PUNCH DIE ROUND 40.5MM EA 1PD50.8 PUNCH DIE ROUND 50.8MM EA 1PD60.5 PUNCH DIE ROUND 60.5MM EA 1PD63.5 PUNCH DIE ROUND 63.5MM EA 1PD88.9 PUNCH DIE ROUND 88.9MM EA 1PD115.5 PUNCH DIE ROUND 115.5MM EA 1


C355

• Dies to suit 5 tonne crimping tool for Australian and New Zealand dimensioned Copper lugs and links

• Hexagonal crimp dies• Made from heat-treated carbon steel

COPPER DIES 5T

Part No. Description Nominal Conductor (mm2)

A/F Hex Die (mm)

Unit Qty

M44-50 HT50 HEX COPPER DIE 6MM2 6 4.4 EA 1M57-50 HT50 HEX COPPER DIE 10MM2 10 5.7 EA 1M63-50 HT51 HEX COPPER DIE 16MM2 16 6.3 EA 1M77-50 HT51 HEX COPPER DIE 25MM2 25 7.7 EA 1M82-50 HT51 HEX COPPER DIE 6MM2 6 8.2 EA 1M92-50 HT51 HEX COPPER DIE 35MM2 32 9.2 EA 1M96-50 HT51 HEX COPPER DIE 25MM2 25 9.6 EA 1M104-50 HT50 HEX COPPER DIE 50MM2 50 10.4 EA 1M115-50 HT51 HEX COPPER DIE 70MM2 70 11.5 EA 1M142-50 HT51 HEX COPPER DIE 95MM2 95 14.2 EA 1M148-50 HT51 HEX COPPER DIE 70MM2 70 14.8 EA 1M165-50 HT50 HEX COPPER DIE 120MM2 120 16.5 EA 1M183-50 HT51 HEX COPPER DIE 150MM2 150 18.3 EA 1M190-50 HT51 HEX COPPER DIE 95MM2 95 19.0 EA 1M200-50 HT50 HEX COPPER DIE 185MM2 185 20.0 EA 1

DIES COPPER

• Custom dies for B035 3.5 ton crimping tool• Hexagonal dies for Copper lugs and links• Range suitable from 6mm2 to 120mm2• Die fits Klauke EK354-L crimp tool

COPPER B035 DIES

Part No. Description Unit QtyB035-6 DIE B035 CU 6MM EA 1B035-10 DIE B035 CU 10MM EA 1B035-16 DIE B035 CU 16MM EA 1B035-25 DIE B035 CU 25MM EA 1B035-35 DIE B035 CU 35MM EA 1B035-50 DIE B035 CU 50MM EA 1B035-70 DIE B035 CU 70MM EA 1B035-95 DIE B035 CU 95MM EA 1B035-120 DIE B035 CU 120MM EA 1


C356

• Crimping dies for Australian and New Zealand dimensioned lugs and links• Hexagonal dies for Copper lugs and links• For 12/13 tonne hydraulic crimp tools• Carbon steel dies

COPPER DIES 12/13T

Part No. Description Conductor Range(mm2)

A/F Hex Die Unit Qty

HT130-C-6 COPPER HEXAGONAL DIE 6MM2 6 4.4 EA 1HT130-C-10 COPPER HEXAGONAL DIE 10MM2 6 4.4 EA 1HT130-C-16 COPPER HEXAGONAL DIE 16MM2 16 6.3 EA 1HT130-C-25 COPPER HEXAGONAL DIE 25MM2 25 7.7 EA 1HT130-C-35 COPPER HEXAGONAL DIE 35MM2 35 9.2 EA 1HT130-C-50 COPPER HEXAGONAL DIE 50MM2 50 10.4 EA 1HT130-C-70 COPPER HEXAGONAL DIE 70MM2 70 11.5 EA 1HT130-C-95 COPPER HEXAGONAL DIE 95MM2 95 14.2 EA 1HT130-C-120 COPPER HEXAGONAL DIE 120MM2 120 16.5 EA 1HT130-C-150 COPPER HEXAGONAL DIE 150MM2 150 18.3 EA 1HT130-C-185 COPPER HEXAGONAL DIE 185MM2 185 20.0 EA 1HT130-C-240 COPPER HEXAGONAL DIE 240MM2 240 23.1 EA 1HT130-C-300 COPPER HEXAGONAL DIE 300MM2 300 26.0 EA 1

• Dies 12/13 tonne crimp heads for heavy duty C-connectors CACD and CACE range• Oval crimp on C-connector• Made from heat-treated carbon steel

COPPER C CONNECTOR DIES 12T

Part No. Description Unit QtyHT130-CC C CONNECTOR CRIMPING DIES 10-35 MM2 EA 1HT130-C0 C CONNECTOR CRIMPING DIES 35-70 MM2 EA 1HT130-C997 C CONNECTOR CRIMPING DIES 95-120 MM2 EA 1HT130-C1011 C CONNECTOR CRIMPING DIES 150-240 MM2 EA 1

Part No. DIESET • 12/13 tonne dies for Australian and New Zealand dimensioned lugs and links• Hexagonal crimp die kit for Cu• Made from heat-treated carbon steel• Copper dies 16sq.mm to 300mm2

12 TON DIE SET 16-300MM2COPPER DIESETS 12T/13T

Unit: EA Qty: 1

Part No. DIESET2 • 12/13 tonne dies for Australian and New Zealand dimensioned lugs, links and overhead line

sleeves• Hexagonal crimp die kit for Cu and Al• Made from heat-treated carbon steel• Cu dies 16 to 300 sq.mm and Al dies 6 to 300mm2

13 TON DIE SET Unit: KIT Qty: 1


C357

• Crimping dies for Australian and New Zealand dimensioned lugs and links• Hexagonal crimp dies for Copper lugs and links• Suitable for 22/23 tonne hydraulic crimping heads

COPPER DIES 23T


A/F Hex Die (mm)

Unit Qty

ECW-H3D-400 DIE - ECW-H3D 400MM2 COPPER 400 28.1 EA 1ECW-H3D-500 DIE - ECW-H3D 500MM2 COPPER 500 31 EA 1ECW-H3D-630 DIE - ECW-H3D 630MM2 COPPER 630 37 EA 1

• Die for 52 tonne crimp heads for Australian and New Zealand dimensioned Copper lugs and links

• Hexagonal crimp die• Die range for large Copper lugs and links up 1000 sq.mm• Adaptor RHU520-AD available for 13 tonne C dies

COPPER DIES 53T


A/F Hex Die (mm)

Unit Qty

RHU520-400 HEX. DIE 400MM A/F 28.1 400 28.1 EA 1RHU520-500 HEX. DIE 500MM A/F 31.0 500 31.0 EA 1RHU520-630 HEX. DIE 630MM A/F 37.0 630 37.0 EA 1RHU520-800 HEX. DIE 800MM A/F 43.2 800 43.2 EA 1RHU520-1000 HEX. DIE 1000MM A/F 48.0 1000 48.0 EA 1

Part No. HT-CACC • Crimping die C type for 12/13 tonne crimper for CACC70 C-connector• Based on old style range• Made from heat treated carbon steel• Also see MC70-C and other dies for CACC range

COPPER C CONNECTOR CACC DIEC CONNECTOR DIES 12TDIES EARTHING COPPER

Unit: EA Qty: 1

Part No. HT-CAEC • Die to suit earthing rod C-connectors range CAEC• Die fits all sizes of CAEC C-connector range• Made from heat-treated carbon steel• Suitable for crimping C-connector CACC95

COMPRESSION DIE FOR CAEC Unit: EA Qty: 1


C358

• Die for CACC range of earth bonding and tap off C-connectors• 12/13 tonne crimp tool C-type hexagonal crimp die• Made from heat-treated carbon steel

HT CACC C-CONNECTOR DIES 12T

Part No. Description Unit QtyMC25-C DIE CACC25 HT&B SERIES TOOLS EA 1MC35-C DIE CACC35 HT&B SERIES TOOLS EA 1MC70-C DIE CACC70 HT&B SERIES TOOLS EA 1MC95-C DIE CACC95 HT&B SERIES TOOLS EA 1MC185-C DIE CACC120 HT&B SERIES TOOLS EA 1

• Indent die for 12/13 tonne Aluminium solid sector conductor• Suitable for Australian and New Zealand sector lugs and links• Requires a NEST die for sector crimps

INDENT CRIMP DIES 12T

Part No. Description Unit QtyHT130-A16INDENT INDENT SECT. ALUM 3/4 CORE 120MM EA 1HT130-A18INDENT INDENT SECT. ALUM 3/4 CORE 185MM EA 1HT130-A19INDENT INDENT SECT. ALUM 3/4 CORE 240MM EA 1

DIES INDENT CRIMP


C359

• Dies to suit 5 tonne crimp tools for Australian and New Zealand dimensioned Aluminium lugs and links

• Hexagonal crimp dies• Made from heat-treated carbon steel

ALUMINIUM DIES 5T


A/F Hex Die (mm)

Unit Qty

M90-50 HT51 HEX ALUM DIE 16-35MM A/F 9.0MM 16 9.0 EA 1M132-50 HT51 HEX ALUM DIE 50-70MM A/F 13.2MM 50 13.2 EA 1M140-50 HT51 HEX ALUM DIE ABC 25MM A/F 14.0MM 25 14.0 EA 1M173-50 HT51 HEX ALUM DIE ABC 35-70MM A/F 17.3MM 95 17.3 EA 1M215-50 HT51 HEX ALUM DIE ABC 95-150MM AF 21.5MM 150 21.5 EA 1M220-50 HT50 HEX ALUM DIE 150-185MM A/F 22.0MM 185 20.0 EA 1

DIES ALUMINIUM

• Dies to suit Australian and New Zealand dimensions Aluminium lugs, links and overhead line sleeves

• C-type die for 12/13 tonne crimp tools• Hexagonal crimp dies• Made from heat-treated carbon steel

ALUMINIUM DIES 12/13T



HT-6/35AL ALUMINIUM HEX.DIE 9.00MM A/F 6-32MM 6-35 9.0 EA 1HT-7/225AL ALUMINIUM HEX DIE 14.0MM A/F 7-225 14.0 EA 1HT-7/250AL ALUMINIUM HEX DIE 14.5MM A/F 7-250 14.5 EA 1HT-7/300-375AL ALUMINIUM HEX DIE 18.0MM A/F 300-375 18.0 EA 1HT-7/450AL ALUMINIUM HEX DIE 19.0MM A/F 7-450 19.0 EA 1HT-19/375AL ALUMINIUM HEX DIE 26.2MM A/F 19-375 26.2 EA 1HT-50/70AL ALUMINIUM HEX DIE 13.2MM A/F 50-70MM 50-70 13.2 EA 1HT-95/120AL ALUMINIUM HEX DIE 17.3MM A/F 95-120MM 95-150 17.3 EA 1HT-150/185AL ALUMINIUM HEX DIE 22.0MM A/F 150-185MM 150-185 22.0 EA 1HT-240/300AL ALUMINIUM HEX DIE 28.4MM A/F 240-300MM 240-300 28.4 EA 1

• 12/13 tonne C-type dies for ABC lugs and links• Hexagonal crimp dies• Made from heat-treated carbon steel

ALUMINIUM ABC DIES 12T



HT-25ABC ALUMINIUM DIE 25MM2 ABC 25 14.0 EA 1HT-35/95ABC ALUMINIUM DIE 35/95MM2 ABC 35-95 17.3 EA 1HT-95/150ABC ALUMINIUM DIE 95/150MM2ABC 95-150 21.5 EA 1


C360

Part No. DIESET3 • 12/13 tonne dies for Australian and New Zealand dimensioned lugs and links• Hexagonal crimp die kit for Al• Made from heat-treated carbon steel• Aluminium dies for 6 sq.mm to 300 sq.mm

ALUMINIUM DIE SETALUMINIUM DIESETS 12/13T

Unit: KIT Qty: 1

• Crimping dies for Australian and New Zealand dimensioned lugs and links• Hexagonal crimp dies for Aluminium lugs and links• Suitable for 22/23 tonne hydraulic crimping heads

ALUMINIUM DIES 23T


A/F Hex Die (mm)

Unit Qty

ECW-H3D4/500AL DIE ALUM. ECW-H3D 400/500 500 39.0 EA 1

• Die for 52 tonne crimp head for Australian and New Zealand dimensioned Aluminium lugs and links

• Hexagonal crimp die• Made from heat treated carbon steel

ALUMINIUM DIES 53T


A/F Hex Die (mm)

Unit Qty

RHU520-4/500AL HEX. DIE ALUM. 4/500MM A/F 39.0 500 39.0 EA 1RHU520-1000AL HEX. DIE ALUM. 1000MM A/F 52.5 1000 52.5 EA 1

• NEST dies for 12/13 tonne Aluminium solid sector conductor• Suitable for Australian and New Zealand sector lugs and links• Requires an indent die for sector crimps

ALUMINIUM NEST CRIMP DIE 12T

Part No. Description Unit QtyHT130-A14NEST NEST SECT. ALUM 4 CORE 70-120MM EA 1HT130-A12NEST NEST SECT. ALUM 3 CORE 70-300MM EA 1HT130-A15NEST NEST SECT. ALUM 4 CORE 150-300MM EA 1

DIES ALUMINIUM NEST CRIMP


C361

Part No. MB52-50 • Cutting dies for 5 tonne hydraulic crimping tools to cut copper or aluminium • Made from heat-treated carbon steel• No adjustments required• Less costly than dedicated cutting tools• Suitable for cutting up to 10mm diameter wire

HT50 WIRE CUTTING DIE 10MM OCUTTING DIES 5TDIES CUTTING

Unit: EA Qty: 1

Part No. HT-131-CD • Cutting die for 12/13 tonne C-type hydraulic crimping tools, with a cutting diameter of 16mm• Australian designed and manufactured• Less costly than dedicated cutting tools• No adjustments required for cutting different materials• Suits all 12/13 tonne ‘C’ or ‘U’ style crimp tools

WIRE CUTTER DIE - 12TCUTTING DIES 13T

Unit: EA Qty: 1

Part No. WT2-30 • Cutting die for 22/23 tonne hydraulic crimping tools with a cutting diameter of 20mm• Made from heat-treated carbon steel

CUTTING DIE SET FOR ECW-H3D CRIMP HEADCUTTING DIES 23T

Unit: EA Qty: 1

Part No. MC35-50 • Die for Burndy Insulink• One die fits all

HT50 DIE-ALL SIZE INSULINK 35MMINSULINK DIES 5TDIES INSULINK

Unit: EA Qty: 1

Part No. ECW-H3D-AD • Adaptor for 22/23 tonne crimp head to fit 12/13 tonne C-type crimp dies• Suits Cembre crimp head ECW-H3D• Adapts 23 tonne tool to crimp large range of lugs and links

ADAPTOR ECW-H3D 12 TON DIESADAPTORS 12TADAPTORS

Unit: EA Qty: 1


C362

Part No. RHU520-AD • Adaptor allows use 13 tonne C-type dies with RHU520 52 tonne crimp heads• Fits standard 12/113 tonne C-dies• Extends range of RHU520 to smaller size crimp dies

ADAPTOR RHU520 TO 12 TON DIE Unit: EA Qty: 1

• Designed for safely trimming branches from either an aerial bucket or the ground• Light-weight and balanced with strong insulated fibreglass pole• Packed with safety features• Designed with a ‘Cool Running’ handle for operator comfort• Can be used on both open and closed hydraulic systems

HYDRAULIC POLE SAW

Part No. Description Unit QtyMSS-HPS-1500-FF-C POLE SAW 150CM FOAM FILLED WITH COUPLERS EA 1MSS-HPS-1800-FF-C POLE SAW 180CM FOAM FILLED WITH COUPLERS EA 1

HYDRAULIC POLE SAWS

Documents

Specialist Tools & Accessories · SPECIALIST TOOLS AND ACCESSORIES C342 CRIMPING TOOLS The crimping tools are supplied with OLED display, which provide essential real time tool operating