16
INSTALLATION GUIDE STANDING SEAM

STANDING SEAM INSTALLATION GUIDE...Don STANDING SEAM t 1 Page 1 MetalMax Installation Book.xlsx Pg. 2 Pg. 2 Pg. 3 Pg. 4 Pg. 5 Pg. 6 Pg. 7 Pg. 8 Pg. 9 Pg. 10 Pg. 11 Pg. 12 Pg. 13 Pg

  • Upload
    others

  • View
    19

  • Download
    0

Embed Size (px)

Citation preview

Page 1: STANDING SEAM INSTALLATION GUIDE...Don STANDING SEAM t 1 Page 1 MetalMax Installation Book.xlsx Pg. 2 Pg. 2 Pg. 3 Pg. 4 Pg. 5 Pg. 6 Pg. 7 Pg. 8 Pg. 9 Pg. 10 Pg. 11 Pg. 12 Pg. 13 Pg

INSTALLATIONGUIDE

STANDING SEAM

Page 2: STANDING SEAM INSTALLATION GUIDE...Don STANDING SEAM t 1 Page 1 MetalMax Installation Book.xlsx Pg. 2 Pg. 2 Pg. 3 Pg. 4 Pg. 5 Pg. 6 Pg. 7 Pg. 8 Pg. 9 Pg. 10 Pg. 11 Pg. 12 Pg. 13 Pg

Don’t Buy from the Middle Man. . .

STANDING SEAM Installation Guide

1

Page  1 MetalMax  Installation  Book.xlsx

Pg.  2Pg.  2

Pg.  3Pg.  4Pg.  5Pg.  6Pg.  7

Pg.  8Pg.  9Pg.  10Pg.  11Pg.  12Pg.  13Pg.  14

SS  Side  Wall  and  End  Wall  ……………………………………………………..SS  Step  Ridge  and  Vented  Ridge  …………………………………………….

SS  Panel  and  Trim  Installation

Table  Of  Contents

SS  Panel  Information

SS  Flashing  Profiles

SS  Pitch  Change  and  Valley  ……………………………………………………

SS  Single  Slope  and  Hip  …………………………………………………………SS  Plumb  Eave  and  Flush  Eave  ……………………………………………….SS  Box  rake  and  Step  Rake...…………………………………………………….

SS  Valley,  SS  Pitch  Change,  Z-­‐Bar,  Cleat,  and  Offset  Cleat……..….SS  End  Wall,  Side  Wall,  Reglet  and  Counter  Flashing…………...……SS  Ridge  and  Hips………………………………....……..……………………..…..SS  Rake's……..…..……………………….…………………..……………..………..

Field  Hemming  of  Panel……………………………………………………...….

SS  Eave's………………………..….…….………………....……………………..…..

SS  16  Panel  Profile………………...…….………………………...…….………..SS  14  Panel  Profile…………………………………………….…....……………..

Page 3: STANDING SEAM INSTALLATION GUIDE...Don STANDING SEAM t 1 Page 1 MetalMax Installation Book.xlsx Pg. 2 Pg. 2 Pg. 3 Pg. 4 Pg. 5 Pg. 6 Pg. 7 Pg. 8 Pg. 9 Pg. 10 Pg. 11 Pg. 12 Pg. 13 Pg

Buy Direct from the Metal Man!

www.metalmax.com

2

Page  2 MetalMax  Installation  Book.xlsx

SS  14"  Panel  Profile

SS  16"  Panel  Profile

 Blank:10.22"

Page 4: STANDING SEAM INSTALLATION GUIDE...Don STANDING SEAM t 1 Page 1 MetalMax Installation Book.xlsx Pg. 2 Pg. 2 Pg. 3 Pg. 4 Pg. 5 Pg. 6 Pg. 7 Pg. 8 Pg. 9 Pg. 10 Pg. 11 Pg. 12 Pg. 13 Pg

Don’t Buy from the Middle Man. . .

STANDING SEAM Installation Guide

3Page  3 MetalMax  Installation  Book.xlsx

SS  Plumb  Eave

Specify  Pitch:

Specify  Pitch:Blank:    8.18"

SS  Square  Rake

Blank:  8.5"

Blank:    8.5"

SS  Flush  Eave

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Page 5: STANDING SEAM INSTALLATION GUIDE...Don STANDING SEAM t 1 Page 1 MetalMax Installation Book.xlsx Pg. 2 Pg. 2 Pg. 3 Pg. 4 Pg. 5 Pg. 6 Pg. 7 Pg. 8 Pg. 9 Pg. 10 Pg. 11 Pg. 12 Pg. 13 Pg

Buy Direct from the Metal Man!

www.metalmax.com

4

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Page  4 MetalMax  Installation  Book.xlsx

 SS  Step  Rake  16

Blank:  13.63"

 SS  Step  Rake  14

 Blank:  13.63"

 SS  Box  Rake

 Blank:10.22"

2-1/8”

Page 6: STANDING SEAM INSTALLATION GUIDE...Don STANDING SEAM t 1 Page 1 MetalMax Installation Book.xlsx Pg. 2 Pg. 2 Pg. 3 Pg. 4 Pg. 5 Pg. 6 Pg. 7 Pg. 8 Pg. 9 Pg. 10 Pg. 11 Pg. 12 Pg. 13 Pg

Don’t Buy from the Middle Man. . .

STANDING SEAM Installation Guide

5Page  5 MetalMax  Installation  Book.xlsx

 SS  Single  Slope  Ridge

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

SS Step Ridge

SS Hip Gap

Page 7: STANDING SEAM INSTALLATION GUIDE...Don STANDING SEAM t 1 Page 1 MetalMax Installation Book.xlsx Pg. 2 Pg. 2 Pg. 3 Pg. 4 Pg. 5 Pg. 6 Pg. 7 Pg. 8 Pg. 9 Pg. 10 Pg. 11 Pg. 12 Pg. 13 Pg

Buy Direct from the Metal Man!

www.metalmax.com

6Page  6 MetalMax  Installation  Book.xlsx

SS  Counter  Flashing

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

SS Side Wall

SS End Wall

SS Reglet Flashing

Page 8: STANDING SEAM INSTALLATION GUIDE...Don STANDING SEAM t 1 Page 1 MetalMax Installation Book.xlsx Pg. 2 Pg. 2 Pg. 3 Pg. 4 Pg. 5 Pg. 6 Pg. 7 Pg. 8 Pg. 9 Pg. 10 Pg. 11 Pg. 12 Pg. 13 Pg

Don’t Buy from the Middle Man. . .

STANDING SEAM Installation Guide

7

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Page  7 MetalMax  Installation  Book.xlsx

 SS  Valley

Blank:  20.44"

 SS  Pitch  Change

 *Specify  Upper  Pitch  *Specify  Low  Pitch  Blank:  13.63

 SS  16  Z-­‐Bar          SS  14  Z-­‐Bar SS  Cleat SS  Offset  Cleat

8-3/4”

7/8”

Page 9: STANDING SEAM INSTALLATION GUIDE...Don STANDING SEAM t 1 Page 1 MetalMax Installation Book.xlsx Pg. 2 Pg. 2 Pg. 3 Pg. 4 Pg. 5 Pg. 6 Pg. 7 Pg. 8 Pg. 9 Pg. 10 Pg. 11 Pg. 12 Pg. 13 Pg

Buy Direct from the Metal Man!

www.metalmax.com

8

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Page  8 MetalMax  Installation  Book.xlsx

SS  Box  RakePop  RivetSS  Z-­‐Bar1"  Pancake  Head  ScrewButyl  TapeSS  Panel  Bend  up

SS  Box  Rake

Cleat

2)  If  panel  rib  will  not  be  under  box  trim,  you  will  need  to  bend  up  end  1".3)  Attach  cleat  to  fascia  using  a  pancake  head  screw  every  24"  on  center.

SS  Step  Rake1"  1/4"  Painted  Screw

Butyl  Tape

Cleat

1"  Pancake  Head  ScrewSS  Step  Rake

1)  Attach  cleat  with  pancake  head  screws  every  24"  on  center.

2)  If  panel  rib  will  not  be  under  step  rake  trim,  you  will  need  to  bend  up  end  1".

1)  Measure  where  the  z-­‐bar  needs  to  go  on  panel,  apply  butyl  tape  to  bottom  side  of  z-­‐bar  and  screw  down  with  pancake  head  screw  every  12"  on  center.

4)  Attach  box  rake  trim  by  hooking  it  over  the  cleat  first  and  then  the  z-­‐bar  and  secure  with  pop  rivet  every  24"  on  center.

3)  Apply  butyl  tape  to  the  step  down  leg  of  trim,  hook  over  cleat  and  screw  down  trim  with  a  1-­‐1/2"  woodscrew  every  12"  on  center.

1” 1/2”

Page 10: STANDING SEAM INSTALLATION GUIDE...Don STANDING SEAM t 1 Page 1 MetalMax Installation Book.xlsx Pg. 2 Pg. 2 Pg. 3 Pg. 4 Pg. 5 Pg. 6 Pg. 7 Pg. 8 Pg. 9 Pg. 10 Pg. 11 Pg. 12 Pg. 13 Pg

Don’t Buy from the Middle Man. . .

STANDING SEAM Installation Guide

9Page  9 MetalMax  Installation  Book.xlsx

SS  Plumb  Eave

Panel

Plumb  Eave

Underlayment

1)  Attach  eave  trim  with  pancake  head  screw  24"  on  center.

2)  Hem  panel  and  attach  panel  to  eave  trim.

SS  Flush  Eave

Panel

1"  Pancake  Head  Screw

Offset  Cleat

Butyl  Tape

Flush  Eave

1"  Pancake  Head  Screw

Cleat

2)  Attach  trim  over  the  cleat.

1)  Attach  cleat  to  fascia  with  pancake  head  screw  24"  on  center.  Mak  sure  that  the  cleat  will  set  in  the  open  hem  of  trim.

3)  Apply  butyl  tape  to  the  bottom  side  of  the  1-­‐1/2"  leg  of  the  offset  cleat  .  Attach  the  offset  cleat  on  top  of  the  eave  trim  with  pancake  head  screw.  Hem  panel  and  attach  to  the  offset  cleat.

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Page 11: STANDING SEAM INSTALLATION GUIDE...Don STANDING SEAM t 1 Page 1 MetalMax Installation Book.xlsx Pg. 2 Pg. 2 Pg. 3 Pg. 4 Pg. 5 Pg. 6 Pg. 7 Pg. 8 Pg. 9 Pg. 10 Pg. 11 Pg. 12 Pg. 13 Pg

Buy Direct from the Metal Man!

www.metalmax.com

10

Page  10 MetalMax  Installation  Book.xlsx

     SS  Single  Slope  Ridge  

Pop  Rivet SS  Single  Slope  RidgeZ-­‐BarButyl  Tape1"  Pancake

head  screw Cleat

     SS  Hip   Pop  Rivet                  SS  Hip Pop  Rivet

Z-­‐Bar    1"  Pancakehead  screw

1)  Marke  panels  off  for  z-­‐bar.

3)  Hook  hip  trim  on  z-­‐bar  and  secure  with    pop  rivets.

1)  Marke  panels  off  for  z-­‐bar.  Apply  butyl  tape  to  bottom  side  of  Z-­‐Bar.  Attach  Z-­‐Bar  to  panel  with  1"  pancake  head  screw  and  seal  edges  of  Z-­‐Bar  were  they  meet  panel  ribs.

2)  Attach  cleat  to  fascia  side  with  1"  pancake  head  screw.  Hook  Single  slope  ridge  trim  over  cleat  and  Z-­‐Bar.  Secure  trim  to  Z-­‐Bar  with  pop  rivet.

2)  Cut  z-­‐bar  the  width  of  the  panel,  Apply  butyl  tape  to  bottom  side  of  z-­‐bar  and  attach  z-­‐bar  to  panels.  Apply  sealer  on  both  ends  where  z-­‐bar  meets  panel  ribs.

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Page 12: STANDING SEAM INSTALLATION GUIDE...Don STANDING SEAM t 1 Page 1 MetalMax Installation Book.xlsx Pg. 2 Pg. 2 Pg. 3 Pg. 4 Pg. 5 Pg. 6 Pg. 7 Pg. 8 Pg. 9 Pg. 10 Pg. 11 Pg. 12 Pg. 13 Pg

Don’t Buy from the Middle Man. . .

STANDING SEAM Installation Guide

11

Page  11 MetalMax  Installation  Book.xlsx

2)  Apply  sealer  to  both  sides  of  z-­‐bar  where  the  trim  meets  the  panel  ribs.

Pop  Rivet Step  Ridge  Cap

Vented  Closure Closure  Clip

1)  Mark  your  panels  for  ridge  cap  placement.

2)Apply  vented  closure  strip  to  panels  and  secure  with  closure  clips  and  2  each  screws.3)Hook  ridge  cap  over  clips  and  secure  with  a  pop  rivet.

SS  Step  Ridge

             Z-­‐Bar          Pancake  Head  Screw              SS  Ridge  Cap            Butyl  tape      Sealer(Edge's  of  z-­‐bar)    Pop  Rivet

1)  Cut  z-­‐bar  to  fit  inside  of  panel,  apply  butyl  tap  to  bottom  side  of  z-­‐bar  and  attach  to  roof  with  pancake  head  screw.

3)  Attach  Step  ridge  by  hooking  both  sides  of  opem  hem  to  z-­‐bar  and  secureing  with  pop  rivets  every  24"  on  center.

SS  Vented  Step  Ridge

   1"  Pancake  head  screw

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Page 13: STANDING SEAM INSTALLATION GUIDE...Don STANDING SEAM t 1 Page 1 MetalMax Installation Book.xlsx Pg. 2 Pg. 2 Pg. 3 Pg. 4 Pg. 5 Pg. 6 Pg. 7 Pg. 8 Pg. 9 Pg. 10 Pg. 11 Pg. 12 Pg. 13 Pg

Buy Direct from the Metal Man!

www.metalmax.com

12

Page  12 MetalMax  Installation  Book.xlsx

       Sealer

       Reglet  Trim          SS  End  wall          Panel  End        Pop  Rivet        Z-­‐Bar        1"  Pancakehead  screw.

         Butyl  tape

1)  Bend  edge  of  panel  up  about  1".  Measure  over  for  Z-­‐Bar  placement.2)Apply  butyl  tape  to  bottom  side  of  Z-­‐Bar  and  attch  with  1"  pancakehead  screw.

3)Hook  side  wall  trim  over  z-­‐bar  and  secure  with  pop  rivet.  Attach  upper  side  to  wall  with  a  fastener.4)  For  brick,  cut  1/8"  grove  in  wall  and  install  reglet  trim.  Run  a  bead  of  sealer  at  top  edge  of  trim.

     SS  End  Wall  Counter  Flashing

Sealer OR  Reglet  Trim

SS  End  Wall

Pop  rivetZ-­‐Bar

Butyl  Tape1"  Pancake  head  screw

1)  Measure  over  for  Z-­‐Bar  placement.2)Apply  butyl  tape  to  bottom  side  of  Z-­‐Bar  and  attch  with  1"  pancakehead  screw.

3)Hook  end  wall  trim  over  z-­‐bar  and  secure  with  pop  rivet.  Attach  upper  side  to  wall  with  a  fastener.

4)  For  brick,  cut  1/8"  grove  in  wall  and  install  reglet  trim.  Run  a  bead  of  sealer  at  top  edge  of  trim.

SS  Side  Wall  

5)  For  siding,  remove  bottom  J-­‐Channel  and  attach  upper  side  of  trim  to  wall.  Re-­‐Install  J-­‐  Channel  and  siding.

5)  For  siding,  remove  bottom  J-­‐Channel  and  attach  upper  side  of  trim  to  wall.  Re-­‐Install  J-­‐  Channel  and  siding.

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Page 14: STANDING SEAM INSTALLATION GUIDE...Don STANDING SEAM t 1 Page 1 MetalMax Installation Book.xlsx Pg. 2 Pg. 2 Pg. 3 Pg. 4 Pg. 5 Pg. 6 Pg. 7 Pg. 8 Pg. 9 Pg. 10 Pg. 11 Pg. 12 Pg. 13 Pg

Don’t Buy from the Middle Man. . .

STANDING SEAM Installation Guide

13Page  13 MetalMax  Installation  Book.xlsx

SS  Pitch  Change Pop  rivet

Offset  Cleat

Butyl  Tape                1"Pancakehead  Screw Z-­‐Bar

1)  Install  Lower  panel  first.

3)  Attach  pitch  change  trim  by  hooking  over  Z-­‐Bar  and  securing  with  a  pop  rivet.  

 SS  ValleyOffset  Cleat Valley Offset  Cleat

1"  Pancakehead  Screw Butyl  Tape

1)  Attach  valley  with  1"  pancake  head  screw  at  outside  edges.

3)  Apply  hem  to  panel  and  hook  over  offset  cleat.

4)  Apply  butyl  tape  to  bottom  side  of  offset  cleat  and  attach  to  upper  side  of  pitch  change  with  a  1"  pancake  head  screw.  Hem  panel  and  hook  over  offset  cleat.

SS  Pitch  Change

2)  Apply  butyl  tape  to  bottom  side  of  Z-­‐Bar  and  attach  to  lower  panels.  Apply  sealer  to  both  sides  of  z-­‐bar  where  the  trim  meets  the  panel  ribs.

2)  Apply  butyl  tape  to  bottom  side  of  offset  cleat  and  attach  offset  cleat  to  valley  about  5"  from  center  of  valley  with  1"  pancake  head  screw.

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Page 15: STANDING SEAM INSTALLATION GUIDE...Don STANDING SEAM t 1 Page 1 MetalMax Installation Book.xlsx Pg. 2 Pg. 2 Pg. 3 Pg. 4 Pg. 5 Pg. 6 Pg. 7 Pg. 8 Pg. 9 Pg. 10 Pg. 11 Pg. 12 Pg. 13 Pg

Buy Direct from the Metal Man!

www.metalmax.com

14Page  14 MetalMax  Installation  Book.xlsx

Page 16: STANDING SEAM INSTALLATION GUIDE...Don STANDING SEAM t 1 Page 1 MetalMax Installation Book.xlsx Pg. 2 Pg. 2 Pg. 3 Pg. 4 Pg. 5 Pg. 6 Pg. 7 Pg. 8 Pg. 9 Pg. 10 Pg. 11 Pg. 12 Pg. 13 Pg

WWW.METALMAX.COM