SUB-ZERO DESIGN GUIDE - Sub-Zero and Wolf … DESIGN GUIDE 3 IMPORTANT NOTE As you follow these instructions, you will notice warning and caution symbols. This blocked information

SUB-ZERO DESIGN GUIDE

SUB-ZERO® is a registered trademark of Sub-Zero, Inc.

C O N T E N T S

Built-In Refrigeration 4

Integrated Refrigeration 31

Wine Storage 50

Undercounter Refrigeration 67

Warranty 77

Features and specifications indicatedherein and on our website are subjectto change at any time without notice.Check our website, subzero.com, forthe most up-to-date specifications.

S U B - Z E R O D E S I G N G U I D E

3

I M P O R T A N T N O T E

As you follow these instructions, youwill notice warning and caution symbols.This blocked information is importantfor the safe and efficient installation ofSub-Zero equipment. There are twotypes of potential hazards that mayoccur during installation.

Another footnote we would like toidentify is IMPORTANT NOTE: Thishighlights information that is especiallyrelevant to a problem-free installation.

signals a situation where minorinjury or product damage may occurif you do not follow instructions.

states a hazard that may causeserious injury or death if precautionsare not followed.

C O N T A C TI N F O R M AT I O N

Sub-Zero CustomerService:800-222-7820

Website:subzero.com

W E L C O M E T O S U B - Z E R O

We make the ultimate built-in, integrated andundercounter refrigerators, freezers and winestorage units. We offer more solutions to yourdaily design problems of trying to work thelargest appliance into a home without beingobtrusive. Placing refrigeration in the home is nolonger a problem, but, rather, an opportunity toexercise your creativity.

Sub-Zero has rethought traditional built-inrefrigeration, a category it pioneered, with over60 years of experience. When our complete lineof configurations—all refrigerator and all freezer,over-and-under, or side-by-side—are coupledwith three design alternatives and classic,platinum and carbon stainless steel finishes, theresult is unlimited flexibility in satisfying yourclient‘s needs for residential refrigeration.

Created to blend invisibly into your home‘sdecor, the Integrated line lets you incorporaterefrigeration anywhere in the house—the kitchen,master suite, media room or workout room.These tall units or two-drawer base refrigerators,freezers and combination units can be hiddeninside the furniture or cabinetry of yourchoosing.

Sub-Zero is breaking with conventional ways ofoffering Wine Storage for designers and theirclients. Our Built-In and Integrated models, alongwith the free-standing Model 424FS, offer unlim-ited design and storage capabilities.

Our reputation is legendary. We have engineeredand manufactured the best products in thebusiness, and we stand behind our productswith an unsurpassed warranty and a network oftechnicians to help you if service is necessary.See details of our warranty at the end of thisguide.

Comprehensive installation instructions areshipped with each model. Refer to thoseinstructions in preparing and installing allSub-Zero products. These instructions alongwith product specifications and downloadable2D and 3D CAD files, as well as pdf files can befound on our website, subzero.com.

Dimensions inparentheses are inmillimeters unlessotherwise specified.

B U I LT - I N R E F R I G E R A T I O N

4


Sub-Zero’s Built-In line offers you the mostcomplete set of design options in built-in refrig-eration for all of its models, from the classic lookof the framed unit to the beauty of the overlaymodels and the professional treatment of thewrapped stainless steel doors.

Aside from the classic stainless steel, Sub-Zerooffers platinum and carbon premium stainlesssteel finishes on its Built-In models and manyrelated accessories. The only exception to thesedesign alternatives are Models 648PRO and648PROG, which are offered only in the classicstainless steel design application. In addition,Models 685 and 695 are offered in framed,overlay and classic stainless steel (not platinumor carbon).

Glass doors are available on our Models 601R,611 and 650. They each come in a framed,overlay and stainless steel design. They all meetstringent Department of Energy standards.Model 648PROG also features a glass door in itsclassic stainless steel look.

In the illustrations, we have shown the threedifferent design configurations of the framed,overlay and stainless steel units applied toModel 695. Please note how we qualify thedifferent looks with the model number.

The traditional framed units come with anelegant full-length handle and an 11" (279)louvered grille.

Model 695/SClassicStainless Steel

Model 695/OOverlay

Model 695/FFramed

Overlay models will come with no handlehardware, because the beauty of this design isthat you can match the surrounding cabinetryhardware; however, we do offer optional handlesas sales accessories. The new ice and waterdispensing Models 685 and 695 are able toaccept overlay panels. Overlay models will comewith a standard 11" (279) panel grille that willaccept decorative panel inserts. Models 601R,601RG and 601F are only available with thelouvered grille. No panel grille option is available.

All stainless steel models, with the exception ofthose mentioned earlier, are offered in the classicstainless steel finish and in the premium finishesof platinum and carbon. Stainless steel modelscome with a standard 11" (279) heavy-dutygrille, 1" (25) diameter stainless steel handlesand a stainless steel kickplate.

All grilles will be offered as options in 1" (25)increments from 10" (254) to 15" (381) and canbe ordered as sales accessories. Models 601R,601RG, 601F, 648PRO and 648PROG are theexception and are available only with an 11"(279) grille.

An important step in assuring a successful planis to make sure that the actual equipmentshipped to your installation site matches thedesign you have ordered. Each of these threedesign options—framed, overlay and stainlesssteel—has specific installation requirements,which means it is vital that the unit match yourplanning and space needs.

B U I L T - I N R E F R I G E R A T I O N

5

36" (914)

73" (1854)

36" (914)

42" (1067)

42" (1067)

48" (1219)

48" (1219)

48" (1219)

48" (1219)

84" (2134)

84" (2134)

84" (2134)

84" (2134)

84" (2134)

84" (2134)

84" (2134)

30" (762)

84" (2134)

A L L R E F R I G E R AT O R | A L L F R E E Z E R

O V E R - A N D - U N D E R

S I D E - B Y - S I D E

M O D E L 6 0 1 R

All Refrigerator

Energy StarQualified

M O D E L 6 0 1 R G

All Refrigeratorwith Glass Door


M O D E L 6 0 1 F

All Freezer

With the installation of a harness kit,these appliances are Star-K compliantto meet strict religious regulations inconjunction with specific instructionsfound on www.star-k.org. Models648PRO and 648PROG are Star-Kcertified from the factory with no extrawiring harness required. For detailsabout the harness kit, contact yourSub-Zero dealer.

36" (914)

73" (1854)

36" (914)

73" (1854)

M O D E L 6 6 1 M O D E L 6 4 2 M O D E L 6 8 5

Ice | WaterDispensing

M O D E L 6 3 2 M O D E L 6 9 5

Ice | WaterDispensing

M O D E L 6 4 8 P R O

Free-Standingor Built-In

M O D E L 6 4 8 P R O G

Free-Standingor Built-In

M O D E L 6 1 1


M O D E L 6 1 1 G

with Glass Door

M O D E L 6 5 0


30" (762)

84" (2134)

36" (914)

84" (2134)

36" (914)

84" (2134)

M O D E L 6 5 0 G

with Glass Door


These illustrations represent the full line ofSub-Zero Built-In models shown in the stain-less steel design application with heavy-dutygrille. Models 648PRO and 648PROG areavailable as built-in or free-standing units inclassic stainless steel only.

For information regarding specific Built-Inmodels, refer to the illustrations in thissection. Regardless of the specific designapplication, framed, overlay or stainless steel,the interior specifications of each model areidentical.

Comprehensive installation instructions areshipped with each model. Refer to thoseinstructions in preparing and installing allSub-Zero products. The instructions can alsobe found on our website, subzero.com.



6

S U B - Z E R OW A R R A N T Y

Sub-Zero productsare covered by atwo, five and twelveyear residentialwarranty (exclusionsapply). See warrantydetails at the end ofthis guide.

B U I LT - I N F E A T U R E S

Framed models—the classic look that madeSub-Zero famous—feature a louvered grille andelegant full-length handle. An optional panel grilleis available for framed units, except for Models601R, 601RG and 601F. Optional panel conver-sion kits are available for the new ice and waterdispensing Models 685 and 695.

Overlay models blend seamlessly into youroverall room design and complement surroundingcabinetry. You add decorative hardware. Overlaymodels come with a panel grille that will acceptdecorative panel inserts. The new ice and waterdispensing Models 685 and 695 are also avail-able in the overlay application.

Stainless steel models feature wrapped doors,1" (25) diameter stainless steel handles and aheavy-duty grille designed specifically to enhancethe aesthetics of today's professional lookingkitchens. All Built-In stainless steel models areoffered in the classic stainless steel finish and inthe premium finishes of platinum and carbon,except for Models 685, 695, 648PRO and648PROG, which are offered in classic stainlesssteel only. The premium finishes are treated asspecial orders and must be ordered 90 daysbefore you expect delivery.

Dual Refrigeration System. All Built-In combina-tion models have the Sub-Zero dual refrigerationsystem, which ensures the freshest food andenergy efficiency at the same time. You haveprecise independent control of the refrigeratorand freezer compartments. In addition to twocompressors, the PRO 48 has three separateevaporators to keep foods fresher longer andprevent odor transfer.

Glass Door. Model 601RG is an all refrigeratorunit featuring a glass door. Models 611G and650G are over-and-under combination units witha glass door on the refrigerator. These glass doormodels come in framed, overlay and stainlesssteel designs and meet stringent Department ofEnergy standards. The side-by-side Model648PROG features a glass door on the refrigera-tor side and comes in classic stainless steel only.

Stainless Steel. The PRO 48 (Models 648PROand 648PROG) feature stainless steel construc-tion inside and out with classic finish forprofessional strength and beauty.

Ice and Water Dispensing. Models 685 and 695feature a dispenser that gives you both ice andchilled water through the refrigerator door.

Built-In Design. True cabinet depth design meansevery inch of the interior is easy to reach. ThePRO 48 can be built in or, with the free-standingaccessory kit, used in a free-standing application.

Fresh Food. High-humidity crisper drawer withremovable dividers is large and deep, withsmooth sides for easy cleaning. The top refriger-ated drawer on the PRO 48 features a tight-seal,retracting glass crisper lid that keeps produceexceptionally humid and fresh.

Electronic Controls. Up-front touch controlsgive you digital readings for quick, easy-to-readreference. The microprocessor provides supremecontrol, accurate to within one degree of presettemperatures, automatic defrosting that senses,then adapts to your use patterns, and a serviceindicator light. The PRO 48 also features exteriortemperature displays.

Advanced Lighting. Bright lighting spreadseven illumination throughout the compartment.The source of the illumination is concealed. ThePRO 48 top LED lights bathe upper compart-ments in a soft glow. On the refrigerator side,channeled sidewall LEDs can even serve as adoor-area night-light for Model 648PROG.

Adjustable Shelves. Cantilevered glass shelvesmake repositioning quick and easy. They are easyto clean, spill proof and steel reinforced for dura-bility. The PRO 48 features glass shelves withstainless steel trim in the refrigerator and 100%stainless steel shelves in the freezer.

Slide-Out Bins. An exclusive PRO 48 feature—these versatile stainless steel bins hold smallitems, remove easily, and fit neatly under anyshelf.

Door Shelves. All door shelves are adjustable forcomplete flexibility and convenience.

Dairy Storage. Dairy compartment is adjustable,with easy, one-door access, compartmentdividers and a clean design. The dairy shelf ismagnetically sealed to maintain freshness.

Automatic Ice. Ice maker provides high-quality,crescent-shaped ice that won‘t stick to the sideof the glass. The PRO 48 features a water filterlocated just behind the easy-access pop-up grille,for ice as pure as it is fresh.

Energy Efficient. Our solid core doors improveinsulation and structural integrity and help usexceed tough Department of Energy standards.Magnetic gaskets around all doors give extra-tight seals.

Kickplate. Solid, adjustable kickplate gives a truebuilt-in look and conforms to American Instituteof Architects standards.

7


M O D E L 6 0 1 F

A L L F R E E Z E R

M O D E L O P T I O N S

Framed Design 601F/F

Overlay Design 601F/O

Classic Stainless Steel 601F/S

Platinum Stainless Steel 601F/P

Carbon Stainless Steel 601F/B

S P E C I F I C AT I O N S

Overall Width 36" (914)

Overall Height 73" (1854)

Overall Depth 24" (610)

Freezer Capacity 19.3 cu ft (547 L)

Min Height Required 723/4" (1848)

Door Swing Clearance 361/16" (916)

Specify Door Swing LH or RH

Annual Energy Usage 737 kWh | $67*

Shipping Wt (F) 378 lbs (171 kg)

Shipping Wt (O) 378 lbs (171 kg)

Shipping Wt (S/P/B) 406 lbs (184 kg)

F R E E Z E R F E AT U R E S

Automatic Ice Maker

3 Adjustable Wire Shelves

1 Stationary Glass Shelf

3 Freezer Storage Drawers

5 Adjustable Door Shelves

M O D E L 6 0 1 R

A L L R E F R I G E R AT O R

Energy Star Qualified


Framed Design 601R/F

Overlay Design 601R/O

Classic Stainless Steel 601R/S

Platinum Stainless Steel 601R/P

Carbon Stainless Steel 601R/B

S P E C I F I C A T I O N S




Refrigerator Capacity 19.9 cu ft (564 L)








R E F R I G E R A T O R F E AT U R E S

4 Adjustable Glass Shelves


High-Humidity Compartment with Dividers

Adjustable Roll-Out Deli Basket


Adjustable Dairy Compartment

Egg Container

M O D E L 6 0 1 R G

A L L R E F R I G E R AT O RW I T H G L A S S D O O REnergy Star Qualified


Framed Design 601RG/F

Overlay Design 601RG/O

Classic Stainless Steel 601RG/S

Platinum Stainless Steel 601RG/P

Carbon Stainless Steel 601RG/B













R E F R I G E R AT O R F E AT U R E S




Triple-Pane UV Resistant Glass Door

Optional Accessory Roll-Out Deli BasketAvailable

Egg Container

Optional High Altitude Glass Available**

601RG

*Annual energy costs are based on9.06 cents per kilowatt hour.

**High altitude glass doors arefor installations at or above 5,000'(1524 m) in elevation and will betreated as a special order. Pleaseallow 90 days for delivery. Whenordering, add an (HA) before the (G)to obtain the correct model number.

All models are shown in the stainlesssteel design application.

M O D E L 6 0 1 R M O D E L 6 0 1 R G M O D E L 6 0 1 F

A C C E S S O R I E SContact your Sub-Zero Dealer

Front panels for framed designin white enamel and classicstainless steel—not available forglass door models

Side panels in white enamel andclassic stainless steel

Extended framed handles

Decorative overlay handles

90˚ and 105˚ door stop kits

Roll-out deli basket(Model 601RG)

Dozen egg container with lid

Harness kit for Star-K compliance



8

M O D E L 6 1 1




Framed Design 611/F

Overlay Design 611/O

Classic Stainless Steel 611/S

Platinum Stainless Steel 611/P

Carbon Stainless Steel 611/B







Min Height Required 83" (2108)






R E F R I G E R AT O R ( D O O R )



High-Humidity Compartment with Divider




Egg Container

F R E E Z E R ( D R A W E R )

Full-Extension Roll-Out Freezer Drawer

Two-Tier Wire Storage Baskets

Automatic Ice Maker

M O D E L 6 1 1 G

O V E R - A N D - U N D E RW I T H G L A S S D O O R


Framed Design 611G/F

Overlay Design 611G/O

Classic Stainless Steel 611G/S

Platinum Stainless Steel 611G/P

Carbon Stainless Steel 611G/B



















Egg Container





Automatic Ice Maker

M O D E L 6 1 1 M O D E L 6 1 1 G





9

M O D E L 6 5 0




Framed Design 650/F

















R E F R I G E R A T O R ( D O O R )







Egg Container




Automatic Ice Maker

M O D E L 6 5 0

M O D E L 6 5 0 G

O V E R - A N D - U N D E RW I T H G L A S S D O O R


Framed Design 650G/F

Overlay Design 650G/O

Classic Stainless Steel 650G/S

Platinum Stainless Steel 650G/P

Carbon Stainless Steel 650G/B



















Egg Container





Automatic Ice Maker

M O D E L 6 5 0 G


Front and grille panels for frameddesign in white enamel andclassic stainless steel


Louvered, panel or stainless steelgrilles in 1" (25) increments from10" (254) to 15" (381) high



Roll-out deli basket (Models 611Gand 650G)



A C C E S S O R I E S

Optional accessoriesare availablethrough yourSub-Zero dealer. Toobtain local dealerinformation, visit theShowroom Locatorsection of ourwebsite,subzero.com.


10

M O D E L 6 8 5

S I D E - B Y - S I D EI C E | W AT E R D I S P E N S I N G


Framed Design 685/F














Shipping Wt (S) 608 lbs (276 kg)




High-Humidity Compartment

1 Storage Drawer




Egg Container


Automatic Ice Maker


1 Stationary Wire Shelf

3 Storage Drawers


2 Juice Can Shelves

M O D E L 6 4 2



Framed Design 642/F





















1 Storage Drawer




Egg Container


Automatic Ice Maker


1 Stationary Solid Shelf

3 Storage Drawers


M O D E L 6 6 1



Framed Design 661/F





















1 Storage Drawer




Egg Container

F R E E Z E R F E A T U R E S

Automatic Ice Maker



4 Storage Drawers


M O D E L 6 6 1 M O D E L 6 4 2 M O D E L 6 8 5



11

M O D E L 6 3 2



Framed Design 632/F





















2 Storage Drawers




Egg Container

F R E E Z E R F E A T U R E S

Automatic Ice Maker



3 Storage Drawers


M O D E L 6 9 5

S I D E - B Y - S I D EI C E | W AT E R D I S P E N S I N G


Framed Design 695/F














Shipping Wt (S) 656 lbs (298 kg)





2 Storage Drawers




Egg Container


Automatic Ice Maker


1 Stationary Wire Shelf

3 Storage Drawers


2 Juice Can Shelves

M O D E L 6 3 2 M O D E L 6 9 5




Front and grille panels for frameddesign in white enamel andclassic stainless steel


Louvered, panel or stainless steelgrilles in 1" (25) increments from10" (254) to 15" (381) high

Framed panel kits (Models 685and 695)*



90˚ and 105˚ door stop kits



*Refer to page 19 for additionalinformation.



12

M O D E L 6 4 8 P R O

S I D E - B Y - S I D EB U I LT - I N O R F R E E - S T A N D I N G




Overall Depth 257/8" (657)






Shipping Weight 860 lbs (390 kg)

R E F R I G E R AT O R(Door and Two Drawers)



2 Adjustable Slide-Out Stainless Steel Bins

1 Crisper Lid

Dividers for Drawers Included

F R E E Z E R(Door and Two Drawers)

Automatic Ice Maker

Water Filtration Filter

3 Adjustable Stainless Steel Shelves

1 Stationary Stainless Steel Shelf

1 Stainless Steel Ice Bucket

M O D E L 6 4 8 P R O G

S I D E - B Y - S I D EW I T H G L A S S D O O RB U I LT - I N O R F R E E - S T A N D I N G




Overall Depth 257/8" (657)






Shipping Weight 875 lbs (397 kg)

R E F R I G E R AT O R(Door and Two Drawers)



2 Adjustable Slide-Out Stainless Steel Bins

1 Crisper Lid

Dividers for Drawers Included



F R E E Z E R(Door and Two Drawers)

Automatic Ice Maker

Water Filtration Filter

3 Adjustable Stainless Steel Shelves

1 Stationary Stainless Steel Shelf

1 Stainless Steel Ice Bucket

M O D E L 6 4 8 P R O M O D E L 6 4 8 P R O G




90˚ door stop kit—right or lefthinge


Slide-out stainless steelrefrigerator bin

Refrigerator drawer dividers

Classic stainless steel side panel

Free-standing kit—includes twostainless steel side panels andtop lid


13


Model 601R36" (914)All Refrigerator

Model 601RG36" (914)All Refrigeratorwith Glass Door

Model 601F36" (914)All Freezer

Model 61130" (762)Over-and-Under

Model 611G30" (762)Over-and-Underwith Glass Door

Model 65036" (914)Over-and-Under

Model 650G36" (914)Over-and-Underwith Glass Door

Model 66136" (914)Side-by-Side


Model 68542" (1067)Side-by-SideIce | Water Dispensing


Model 69548" (1219)Side-by-SideIce | Water Dispensing

Model 648PRO48" (1219)Side-by-SideBuilt-In or Free-Standing

Model 648PROG48" (1219)Side-by-Sidewith Glass DoorBuilt-In or Free-Standing

P L A N N I N G I N F O R M A T I O N

Although the Sub-Zero Built-In line offers a widerange of designs and configurations, the basicplanning considerations for all models havemuch in common. As you integrate Built-Inmodels into your overall plan, review installationrequirements for your particular model(s). TheInstallation Specifications illustrations provideplanning information for all Built-In models—framed, overlay and stainless steel.

Allow the door(s) to open a minimum of 90˚ oryou‘ll have problems removing drawers. With thedoor opening at 90˚, you may have to movedrawers slightly to clear the door interior.

For corner installations, allow for a minimum 3"(76) filler so that the door can open to 90˚. Ifyou‘re using raised panels, consider using awider filler.

When units are installed side by side, a filler stripis recommended. The width of this filler strip willvary depending on the configuration and panelsyou use.

Be sure to add the filler strip width to yourfinished rough opening dimension. In anyinstallation of two units side by side without afiller strip, add an additional 1/2" (13) to yourcombined numbers. This will allow for theproper width.

IMPORTANT NOTE: Refer to the full-scale illus-trations at the end of this section for specificson door openings and filler size alternatives.

E L E C T R I C A L R E Q U I R E M E N T S

A 115 V AC, 60 Hz, 15 amp circuit breaker andelectrical supply are required. A separate circuit,servicing only this appliance, is required.

All Sub-Zero Built-In models are equipped with apower supply cord with a 3-prong groundingplug, which must be plugged into a mating3-prong grounding-type wall receptacle. Followthe National Electrical Code and local codes andordinances when installing the receptacle. Referto the Installation Specifications illustration foryour model on the following pages.

IMPORTANT NOTE: A ground fault circuitinterrupter (GFCI) is not recommended and maycause interruption of operation.

P L U M B I N G C O N S I D E R A T I O N S

For Built-In models with an automatic ice maker,rough in the water supply line. Connect a 1/4"OD copper line to the house supply, being sureto use an easily accessible shut-off valvebetween the supply and the refrigerator.

Do not use self-piercing valves. A saddle valvekit (4200880) is available from your Sub-Zerodealer.

For Built-In models except Models 648PRO and648PROG, a line filter is required when waterconditions have a high sediment content. Theice maker operates on water pressure of 20 psi(1.4 bar) to 100 psi (6.9 bar).

IMPORTANT NOTE: In some cases a reverseosmosis water filter system may not be able tomaintain the minimum water pressure consis-tently.

Models 648PRO and 648PROG come with anautomatic ice maker and an integrated waterfiltration system. This system operates on waterpressure between 35 psi (2.4 bar) and 120 psi(8.3 bar).

IMPORTANT NOTE: A reverse osmosis systemcan be used with Models 648PRO and648PROG, provided there is constant waterpressure of 20 psi (1.4 bar) to 120 psi (8.3 bar)supplied to the unit at all times. In this applica-tion, the integrated water filtration system mustbe set to bypass mode. This is achieved byremoving the water filter cartridge. Refer to thePRO 48 Installation Instructions packed with theunit for detailed instructions.

The water line should be routed up through thefloor within 1/2" (13) from the back wall and nohigher than 3" (76) off the floor. If you have tocome through the wall, make sure the water lineis no more than 3" (76) from the floor.

Regardless of the routing, allow 3' (1 m) ofexcess copper tubing to remain outside the wallor floor for easy connection to the unit. Refer toInstallation Specification illustrations.



14

36"(914)

73"(1854)

36"(914)

73"(1854)

36"(914)

24"(610)

73"(1854)

723/4" (1848)ROUGH OPENING

HEIGHT TOFINISHEDFLOORING

723/4" (1848)MINIMUM HEIGHT

REQUIRED TOFINISHEDFLOORING

(LEVELERS IN)

24"(610)

ROUGHOPENING

DEPTH

11"(279)

3"(76)

24"(610)

W

LOCATE WATER SUPPLYWITHIN BOTTOM SHADEDAREA ONLY (601F ONLY)

LOCATE ELECTRICALWITHIN ENTIRE SHADED AREA

6"(152)

E

SHUT-OFFVALVE

EXTENDWATER LINE

APPROX 36" (914)FROM BACK WALL

(601F ONLY)

351/2" (902)ROUGH OPENING WIDTH

FRONT VIEW

TOP VIEW

I N S T A L L AT I O N S P E C I F I C AT I O N SAll Refrigerator | All Freezer Models

Models 601R and 601RG, which do not havean ice maker, will not require the water lineconnection.

Dimensions are for finished rough openings.

Door swing clearances are based onstainless steel door and handle dimensions.

O V E R A L L D I M E N S I O N SAll Refrigerator | All Freezer Models

A L L R E F R I G E R AT O RA L L F R E E Z E R

Model 601RAll Refrigerator

Model 601RGAll Refrigeratorwith Glass Door

Model 601FAll Freezer

361/16"(916)

237/8"(606)

BEHINDFRAME

3/8"(10)FRAME

EXTENSION

90˚

Model 601RAll Refrigerator

Width 36" (914)

Height 73" (1854)

Depth 24" (610)

Model 601RGAll Refrigeratorwith Glass Door

Width 36" (914)

Height 73" (1854)

Depth 24" (610)

Illustrations shown in stainless steel design.

Model 601FAll Freezer

Width 36" (914)

Height 73" (1854)

Depth 24" (610)

Refer to the full-scale illustrations atthe end of thissection for specificson door openingsand otherspecifications.


15

30"(762)

84"(2134)

36"(914)

84"(2134)

30"(762)

84"(2134)

36"(914)

24"(610)

84"(2134)


HEIGHT TOFINISHED

FLOORING WITHSTANDARD

11" (279) GRILLE

83" (2108)MIN HEIGHT

REQUIRED TOFINISHED

FLOORING(LEVELERS IN)

751/2"(1918)

7"(178)

6"(152)

AROUGH OPENING WIDTH

24"(610)

ROUGHOPENING

DEPTH

E

3"(76)

18"(457)

W

LOCATE WATER SUPPLYWITHIN SHADED AREA

LOCATE ELECTRICALWITHIN SHADED AREA

6"(152)

SHUT-OFFVALVE

FRONT VIEW

TOP VIEW

EXTENDWATER LINE


I N S T A L L A T I O N S P E C I F I C AT I O N SOver-and-Under Refrigerator /Freezer Models

Model 611

A) Rough Opening Width 291/2" (749)

B) Min Door Clearance 301/8" (765)

Model 611G



Model 650



Model 650G





O V E R A L L D I M E N S I O N SOver-and-Under Refrigerator /Freezer Models


Model 611

Model 611Gwith Glass Door

Model 650


B

237/8"(606)

BEHINDFRAME

3/8"(10)FRAME

EXTENSION

90˚

Model 611

Width 30" (762)

Height 84" (2134)

Depth 24" (610)


Width 30" (762)

Height 84" (2134)

Depth 24" (610)

Model 650

Width 36" (914)

Height 84" (2134)

Depth 24" (610)



Width 36" (914)

Height 84" (2134)

Depth 24" (610)

Refer to installationinstructions shippedwith each Wolfproduct for detailedspecifications.



16

36"(914)

42"(1067)

48"(1219)

42"(1067)

48"(1219)

24"(610)

84"(2134)


HEIGHT TOFINISHED

FLOORING WITHSTANDARD

11" (279) GRILLE

83" (2108)MIN HEIGHT

REQUIRED TOFINISHEDFLOORING

(LEVELERS IN)

751/2"(1918)

7"(178)

6"(152)

AROUGH OPENING WIDTH

24"(610)

ROUGHOPENING

DEPTH

E

3"(76)

18"(457)

W



6"(152)

SHUT-OFFVALVE

FRONT VIEW

TOP VIEW

EXTENDWATER LINE


I N S T A L L AT I O N S P E C I F I C AT I O N SSide-by-Side Refrigerator | Freezer Models

Model 661



Model 642



Model 685



Model 632



Model 695





O V E R A L L D I M E N S I O N SSide-by-Side Refrigerator | Freezer Models


Model 661

Model 642

Model 685Ice | Water Dispensing

Model 632


B

237/8"(606)

BEHINDFRAME

3/8"(10)FRAME

EXTENSION

90˚

Model 661

Width 36" (914)

Height 84" (2134)

Depth 24" (610)

Model 642

Width 42" (1067)

Height 84" (2134)

Depth 24" (610)


Width 42" (1067)

Height 84" (2134)

Depth 24" (610)

Model 632

Width 48" (1219)

Height 84" (2134)

Depth 24" (610)



Width 48" (1219)

Height 84" (2134)

Depth 24" (610)


17

48"(1219)

7"(178)

6"(152)

ROUGHOPENING DEPTH

24" (610)STANDARD

26" (660)FLUSH

ROUGHOPENING WIDTH

471/2" (1206) STANDARD

48" (1219) FLUSH

E

3" (76)

6"(152)

W



53/16"(132)

SHUT-OFFVALVE

MIN 36" (914)1/4" COPPERWATER LINE

FRONT VIEW

TOP VIEW

ROUGHOPENING HEIGHT

TO FINISHEDFLOORING

833/4" (2127)STANDARD

841/8" (2137)FLUSH

MIN HEIGHTREQUIRED

TO FINISHEDFLOORING

(LEVELERS IN)831/2" (2121)STANDARD

833/4" (2127)FLUSH

751/2"(1918)

I N S T A L L A T I O N S P E C I F I C AT I O N SPRO 48 Side-by-Side Refrigerator | Freezer Models

Built-In or Free-Standing

Models 648PRO and 648PROG can beused free-standing or installed as a standardor flush built-in application. For standardbuilt-in installations, the face frame of theunit will extend 2" (51) beyond cabinetry.In flush built-in installations, the front of theface frame will be flush with surroundingcabinetry.


O V E R A L L D I M E N S I O N SPRO 48 Side-by-Side Refrigerator | Freezer Models

P R O 4 8S I D E - B Y - S I D E

Model 648PROBuilt-In or Free-Standing

Model 648PROGwith Glass DoorBuilt-In or Free-Standing

Model 648PRO

Width 48" (1219)

Height 84" (2134)

Depth 237/8" (606)*257/8" (657)**

Model 648PROGwith Glass Door

Width 48" (1219)

Height 84" (2134)

Depth 237/8" (606)*257/8" (657)**

48"(1219)

84"(2134)

257/8"(657)

305/32"(766)

237/8"(606)

237/8"(606)

BEHINDFACE

FRAME

257/8"(657)

TO FRONTOF FACEFRAME

283/4"(730)

201/2" (521)

48"(1219)

*Depth from behind face frame to back of unit for standard installation.**Depth from front of face frame to back of unit for flush installation.

Refer to installationinstructions shippedwith each Wolfproduct for detailedspecifications.

Refer to the full-scale illustrations atthe end of thissection for specificson door openingsand otherspecifications.



18

A N T I - T I P B L O C K I N G K I T

To prevent the unit from tipping forward and toprovide a stable installation, the unit must besecured in place with an anti-tip blocking kit. Ifthere is a solid soffit above the unit with clear-ance between the unit and the soffit of 1" (25)or less, you won‘t need to block the unit. But forinstallations with clearances of more than 1"(25), you must block the unit with the anti-tipblocking kit (wood block and hardware) providedwith each Sub-Zero Built-In model. Refer to theBuilt-In Installation Instructions packed with theappliance, which provides step-by-step proce-dures for making sure the unit is installedproperly.

A D D I N G P A N E L S

In your plan for panels, be sure you are workingwith the Sub-Zero panel design family called forin your design. If you have chosen the stainlesssteel design, the unit will be shipped completewith wrapped stainless steel doors and handlehardware. You will not have to install doorpanels.

Specifications on the following pages providepanel dimensions and installation considerationsfor framed and overlay door panels.

Side panels can be used with the framed,overlay and stainless steel design applications.Refer to specifications on page 26.

F R A M E D D O O R P A N E L S

If you and your client have ordered a frameddesign model, you will be adding panels to givethe unit the custom Sub-Zero look. The framedpanel design option is available on all Built-Inunits except Models 648PRO and 648PROG. Forexact door panel dimensions for Built-In framedmodels, refer to the Framed Panel Specificationson pages 20–21. Also refer to the full-scaleillustrations at the end of this section for paneland handle considerations.

The traditional framed models come with anelegant, smooth, full-length handle. Optionalextended full-length handles that provideadditional finger clearance for raised panels areavailable through your Sub-Zero dealer.

If the thickness of the custom panels is lessthan 1/4" (6), they must be backed up with asheet of shim material to build the total thick-ness to 1/4" (6). If the panel is thicker than 1/4"(6), an edge must be routed around the panel toensure a proper fit. Refer to illustrations 1 and 2.

IMPORTANT NOTE: On all framed models,routing, recessing or optional extended handlesmay be required on raised panels for finger clear-ance under the handle. Refer to the full-scaleillustrations at the end of this section.

For glass door Models 601RG, 611G and 650G,the refrigerator door panel must include a cut-out to accommodate the window. Refer to theFramed Panel Specifications on pages 20–21.

IMPORTANT NOTE: On glass door models, theglass portion of the door must be exposed andnot covered by any part of the panel.

For Models 685 and 695, the refrigerator doorpanel must include a cut-out to accommodatethe glasswell and bezel. The thickness of thepanel in this area can range from 1/4" (6) to amaximum of 11/8" (29). If the panel is thicker,provisions must be made to rout out a space toaccommodate the decorative bezel surroundingthe glasswell.

PANELS THICKER THAN 1/4" (6)

Trim reveal 1/4" (6) min

Rout to 1/4" (6)thickness

PANELS 1/4" (6) THICK OR LESS

1/4" (6) Panel

Trim reveal 1/4" (6) min

Illus. 2Illus. 1




19

G L A S S W E L L P A N E L O P T I O N S

If you choose not to use custom wood panelsabove or below the glasswell for Model 685 or695 framed application, a stainless steel insertpanel will be provided with the partial framedaccessory kit. This accessory kit (FRAMPAR),includes partial framed molding and classicstainless steel inset handle panel to provide aspill-resistant finish above and below the glass-well on the refrigerator door only. Refer to theFramed Panel Specifications for this option onpage 21.

With the framed retrofit accessory kit, existingModel 680 or 690 door panels can be used on anew Model 685 or 695 framed unit. This acces-sory kit (FRAMRET) includes framed retrofitmoldings and classic stainless steel inset handlepanels to accommodate existing Model 680 or690 framed refrigerator and freezer door panels.

IMPORTANT NOTE: When using Model 680 or690 raised panels with the framed retrofit kit(FRAMRET), a 1/2" (13) trim reveal down to 1/4"(6) thickness is necessary at the bezel in orderfor the panels to fit properly.

Both accessory kits are available through yourSub-Zero dealer. Refer to the illustrations below.

O P T I O N A L P A N E L G R I L L E

An 11" (279) louvered grille is standard onframed applications. Optional louvered grilles areavailable in 1" (25) height increments from 10"(254) to 15" (381) for all Built-In models exceptModels 601R, 601RG, 601F, 648PRO and648PROG.

You may choose to use Sub-Zero‘s optionalpanel grille for some of your framed applications.The panel grilles can be used with all Built-Inmodels except Models 601R, 601RG, 601F,648PRO and 648PROG and are available in 1"(25) height increments from 10" (254) to 15"(381).

For each model, the width of the panel grille willbe the same, regardless of the height you havechosen. To determine the panel grille insert size,use the width dimension listed for your modeland the height dimension for the grille optionyou have chosen. Specifications for the PanelGrille Option are listed on page 21.

Partial Framed KitFRAMPAR

Framed Retrofit KitFRAMRET

P A N E LR E Q U I R E M E N T S

The weight ofeach framed doorpanel cannot exceed50 lbs (23 kg).

F R A M E D P A N E L S

To install framedpanels, see thedetailed proceduresoutlined in theSub-Zero Built-InInstallationInstructions.



20

C

C C

H

W

H

A

B

D

14"(356)

H

W

H

A

B

14"(356)

F R A M E D D O O R P A N E L S P E C I F I C AT I O N SAll Refrigerator | All Freezer Framed (F) Models

Model 601R W H

Refrigerator Framed Panel 341/8" (867) 5815/16" (1497)

Raised Panel Handle Recess Location –

Refrigerator Panel A) 2915/32" (749)

Model 601RG W H




Window Cut-Out Dimensions 253/8" (645) 413/16" (1046)

Window Cut-Out Location C) 43/8" (111) D) 133/8" (340)

Model 601F W H

Freezer Framed Panel 341/8" (867) 5815/16" (1497)


Freezer Panel A) 2915/32" (749)

IMPORTANT NOTE: Panel specifications are for Built-In framed (F)models. Panel specifications for overlay models are on pages 24–25.

F R A M E D D O O R P A N E L S P E C I F I C AT I O N SOver-and-Under Framed (F) Models

Model 611 W H





Freezer Panel B) 141/16" (357)

Model 611G W H








Model 650 W H






Model 650G W H









Models 601Rand 601F

Model 601RG

Models 611 and 650 Models 611G and 650G

C

W

H

A

C C

D

14"(356)

W

H

A

14"(356)


Panel specificationsare for Built-Inframed (F) models.


21

P A R T I A L F R A M E D D O O R P A N E L O P T I O NIce | Water Dispensing Framed (F) Models

Model 685 W H

Refrigerator Partial Framed Panel 155/8" (397) 6711/16" (1719)

Freezer Partial Framed Panel 155/8" (397) 6711/16" (1719)

Model 695 W H

Refrigerator Partial Framed Panel 1715/16" (456) 6711/16" (1719)

Freezer Partial Framed Panel 1715/16" (456) 6711/16" (1719)

The partial framed accessory kit (FRAMPAR) is required for this option.Kit includes partial framed molding and classic stainless steel insethandle panels for above and below glasswell on the refrigerator door.

P A N E L G R I L L E O P T I O NFramed (F) Models

Models 611 and 611G W

Grille Panel Width 283/16" (716)

Models 650, 650G, 661 W


Models 642 and 685 W




10" (254) Grille H

Grille Panel Height 815/16" (227)

11" (279) Grille (standard) H


12" (305) Grille Height H


13" (330) Grille H


14" (356) Grille H


15" (381) Grille H


For panel grille insert size, use width dimension listedfor your model and height dimension for grille option.11" (279) grille is standard.

F R A M E D D O O R P A N E L S P E C I F I C AT I O N SSide-by-Side Framed (F) Models

Model 661 W H




Refrigerator | Freezer Panel A) 385/32" (969)

Model 642 W H

Refrigerator Framed Panel 24" (610) 6711/16" (1719)




Model 685 W H

Refrigerator Framed Panel 24" (610) 6711/16" (1719)


Glasswell Cut-Out Dimensions 57/8" (150) 127/16" (315)

Glasswell Location (Refrigerator) E) 19/16" (39) F) 289/16" (726)

Model 632 W H





Model 695 W H




Glasswell Location (Refrigerator) E) 19/16" (39) F) 289/16" (726)


For Models 685 and 695, panel thickness in the glasswell area canrange from 1/4" (6) to a maximum of 11/8" (29). If the panel is thicker,you must rout out a minimum 1/4" (6) flat landing area to accommo-date the bezel surrounding the glasswell.

Models 661, 642and 632

WW WW

H14" (356)

WW

H

A

H

F

E

Models 685 and 695 Models 685 and 695Partial Framed Option


To install framedpanels, see thedetailed proceduresoutlined in theSub-Zero Built-InInstallationInstructions.


22

IMPORTANT NOTE: Keep in mind that theSub-Zero door panels have the potential forhitting adjacent cabinets and/or countertopswhen they are opened. You need to be aware ofyour surrounding cabinetry and space limitationswhen using the overlay models. Refer to the full-scale illustrations at the end of this section.

If you are using an overlay door panel withModel 611, 611G, 650 or 650G, it is necessaryto rout a space for the unit‘s lower hinge plateso it does not strike the door panel. Refer toillustration 5.

For Models 611, 611G, 650 and 650G, you willminimize the reveal between the bottom of theoverlay door panel and the top of the overlaydrawer panel. Refer to illustration 6.

IMPORTANT NOTE: If you choose not to rout aspace for the lower hinge plate, you can reducethe total height of the overlay panel (decorativepanel only) by 1/2" (13).

Overlay Panel

5/16"(8)

17/32"(13)

27/32" (21)

Spacer Panel

BackerPanel

1/4"(6) Backer Panel

Overlay Panel

3" (76)

Bottom Edge –Hinge Side(rear view)

Spacer Panel

3/8" (10)

1/2"(13)

Illus. 5 Illus. 6

Do not exceed the overlay decorative panel

dimensions for Models 611, 611G, 650 or

650G listed on page 24. If you try to make

the reveal tighter between the door and

drawer panels, the panels may hit when

opening and closing, causing possible

damage to the panels and the Sub-Zero unit.

O V E R L A Y D O O R P A N E L S

If you and your client have ordered an overlaydesign model, you will be adding panels to givethe unit the custom Sub-Zero look. The overlaypanel design option is available on all Built-Inunits except Models 648PRO and 648PROG.

For exact door panel dimensions for Built-Inoverlay models, refer to the Overlay Panel Speci-fications on pages 24–25.

The overlay design allows decorative panels tocover the door trim for a more seamlessappearance that blends with the design of theroom. To achieve this look, the most commonway is to work with three panels—the decorativeoverlay panel, a 0.10" (3) spacer panel and a 1/4"(6) backer panel. Depending on your cabinetmanufacturer, this could be one panel routed fordifferent dimensions or, more likely, three differ-ent panels.

Regardless of the physical construction of thepanels (routing or three-panel assembly), you willneed to follow the Overlay Panel Specificationson the following pages for exact sizing and panelplacement to ensure a proper fit.

Illustration 3 is a cross section view of the three-panel assembly showing placement of the door,drawer or grille trim. Illustration 4 shows a rearview of the three-panel assembly and criticaldimensions, standard for all models.

Spacer PanelOverlay Panel

1/4" (6)

BackerPanel

.10" (3)

~3/4"(19)

Door/Drawer/Grille Trim1/16" (2)

5/32" (4)

1/4" (6) Backer Panel5/16" (8) min

.10"(3)

Spacer Panel

Overlay Panel

Illus. 4Illus. 3

P A N E LR E Q U I R E M E N T S

The overlay doorpanel assembly mustbe a minimum of5/8" (16) thick andcannot exceed 50 lbs(23 kg).



23

Illustration 8 shows how you can box out alanding space for the bezel using stiles and railsto create this space. Again, keep in mind, thatthe total thickness of the panel at this level mustnot exceed 11/8" (29).

O V E R L A Y P A N E L G R I L L E

Overlay grille panels for the panel grille matchthe design of the door panels. Overlay units,except Models 601R, 601RG and 601F, comestandard with an 11" (279) panel grille. Optionalgrilles are available in 1" (25) height incrementsfrom 10" (254) to 15" (381). Overlay grille panelspecifications for the panel grille are listed onpage 25. Also refer to illustration 4 on page 22for additional overlay panel dimensions.

Do not exceed the panel dimensions listed

for the appropriate overlay grille panel you

are specifying. The decorative panel cannot

be any larger or it may restrict the airflow

to the compressor area and cause problems

with the operation of the Sub-Zero unit.

O V E R L A Y D O O R P A N E L S

For glass door Models 601RG, 611G and 650G,the refrigerator door panel must include a cut-out to accommodate the window. Refer to theOverlay Panel Specifications for Models 601RG,611G and 650G on page 24.

IMPORTANT NOTE: On glass door models, theglass portion of the door must be exposed andnot covered by any part of the panel.

For Models 685 and 695, the refrigerator doorpanel must include a cut-out to accommodatethe glasswell and bezel. The thickness of thepanel in this area can range from 1/4" (6) to amaximum of 11/8" (29).

IMPORTANT NOTE: Regardless of the thicknessof the overlay panel for Model 685 or 695, youmust plan for a flat ’landing’ space for thedecorative bezel surrounding the glasswell area.Refer to page 25 for exact cut-out dimensions ofthe glasswell area in the overlay, spacer andbacker panels. This ’landing’ area can be accom-plished in a number of different ways. We areshowing two in Illustrations 7 and 8 below.

Illustration 7 shows how you can recess thebezel to the inset panel. You must rout out aspace to accommodate the 127/8" (327) heightof the bezel. Also keep in mind that the amountof material you will rout out of the stile will varybecause of the thickness of this element.However, the width of the stile immediatelyadjacent to the bezel must be 17/16" (37). DONOT cut the entire stile to this dimension. In thisillustration you can see that rails above andbelow the bezel give this a finished look. Makesure that the bezel is not supporting weightfrom the panel.

O V E R L A Y P A N E L S

To install overlaypanels, see thedetailed proceduresoutlined in theSub-Zero Built-InInstallationInstructions.

2" (51)Edge ofPanel toCut-Out

Glasswell Cut-Out

17/16" (37) Width of Stile

Adjacent to Bezel

Routing Required

127/8" (327)

Height of Bezel

Illus. 8Illus. 7



24

C

C C

H

W

H

D

H

W

H

C

W

H

C C

D

W

H

O V E R L A Y D O O R P A N E L S P E C I F I C AT I O N SAll Refrigerator | All Freezer Overlay (O) Models

Model 601R W H

Refrigerator Overlay Panel 347/16" (875) 591/4" (1505)

Refrigerator Spacer Panel 331/2" (851) 585/16" (1481)

Refrigerator Backer Panel 341/8" (867) 5815/16" (1497)

Model 601RG W H






Model 601F W H

Freezer Overlay Panel 347/16" (875) 591/4" (1505)

Freezer Spacer Panel 331/2" (851) 585/16" (1481)

Freezer Backer Panel 341/8" (867) 5815/16" (1497)

IMPORTANT NOTE: Panel specifications are for Built-In overlay (O)models. Panel specifications for framed models are on pages 20–21.

O V E R L A Y D O O R P A N E L S P E C I F I C AT I O N SOver-and-Under Overlay (O) Models

Model 611 W H







Model 611G W H








Window Cut-Out Location C) 41/2" (114) D) 5" (127)

Model 650 W H







Model 650G W H








Window Cut-Out Location C) 41/2" (114) D) 5" (127)


Models 611 and 650 Models 611G and650G

Model 601RGModels 601Rand 601F


Panel specificationsare for Built-Inoverlay (O) models.


25

O V E R L A Y G R I L L E P A N E LOverlay (O) Models

Width Dimensions

Models 611 and 611G W

Overlay Panel Width 287/16" (722)

Spacer Panel Width 271/2" (699)

Backer Panel Width 281/8" (714)

Models 650, 650G, 661 W












Height Dimensions

10" (254) Grille H

Overlay Panel Height 91/4" (235)

Spacer Panel Height 85/16" (211)

Backer Panel Height 815/16" (227)

11" (279) Grille (standard) H




12" (305) Grille Height H




13" (330) Grille H




14" (356) Grille H




15" (381) Grille H




For grille panel size, use width dimensionslisted for your model and height dimensionsfor grille option. 11" (279) grille is standard.

Panel grille is available for all overlay unitsexcept Models 601R, 601RG and 601F.

O V E R L A Y D O O R P A N E L S P E C I F I C AT I O N SSide-by-Side Overlay (O) Models

Model 661 W H

Refrigerator Overlay Panel 197/16" (494) 68" (1727)



Freezer Overlay Panel 1415/16" (379) 68" (1727)

Freezer Spacer Panel 14" (356) 671/16" (1703)


Models 642 and 685 W H

Refrigerator Overlay Panel 245/16" (618) 68" (1727)


Refrigerator Backer Panel 24" (610) 6711/16" (1719)


Freezer Spacer Panel 15" (381) 671/16" (1703)


Models 632 and 695 W H

Refrigerator Overlay Panel 28" (711) 68" (1727)






Glasswell Cut-Out – Models 685 and 695 W H


Glasswell Location (Overlay) E) 111/16" (43) F) 283/4" (730)

Glasswell Location (Spacer) E) 11/4" (31) F) 281/4" (718)

Glasswell Location (Backer) E) 19/16" (39) F) 289/16" (726)


For Models 685 and 695, panel thickness in the glasswell area canrange from 1/4" (6) to a maximum of 11/8" (29). If the panel is thicker,you must rout out a minimum 1/4" (6) flat landing area to accommo-date the bezel surrounding the glasswell.


To install overlaypanels, see thedetailed proceduresoutlined in theSub-Zero Built-InInstallationInstructions.

WW

H

Models 661, 642and 632

Models 685 and 695

WW

H

E

F

26


H A N D L E H A R D W A R E

Overlay models come without handle hardware.The beauty of this design is that you can matchthe surrounding cabinet hardware. You or thecabinet manufacturer must provide handlehardware to match the overall decoratingscheme.

The handle hardware must be installed beforeinstalling the panel assembly. Use larger D-stylehandles. If screws with thick heads are used,the screws will need to be countersunk into thedoor before the panel is put into place.

IMPORTANT NOTE: Sub-Zero does not recom-mend using single pull knobs on any of its Built-In models.

For overlay Models 685 and 695, mountingplacement of the refrigerator door handle mustassure proper access to the glasswell andadequate clearance under the handle. Illustration9 shows placement of the refrigerator doorhandle in relationship to the glasswell bezel onstainless steel models.

Optional stainless steel handles are available in avariety of diameters and lengths, as are handlesto match the color and style of Wolf ovens.Contact your Sub-Zero dealer for specifics.

Refer to the full-scale illustrations at the end ofthis section for handle hardware considerations.

S I D E P A N E L S

Side panels can be used with the framed,overlay and stainless steel design applications.When planning for side panels with the installa-tion of a Built-In model, you need to be aware ofspace configuration to achieve a pleasing fit.Depending on the exact panel you are using withyour unit, the height of the panel will vary.

Cut-outs around the toe kick and grille area arerequired if a 1/4" (6) thick panel will be insertedinto the main frame channel. The panel will needto be 24" (610) deep. If a 3/8" (10) thick panel isused, the panel will abut the main frame andshould be 237/8" (606) deep. Refer to illustra-tions 10–12 below for placement of toe kick andgrille area cut-outs for your specific model.These dimensions do not apply to Models648PRO and 648PROG.

The toe kick area may or may not be cut outdepending on the look you want to achieve.

IMPORTANT NOTE: The use of side panels maychange the width of your rough opening.

4" (102)

3" (76)

237/8" (606)BEHIND FRAME

Illus. 10—Models 601R,601RG and 601F

2"(51)

GlasswellProfile

HandleProfile

1"(25)

Illus. 9



131/4" (337)

4" (102)

1/4" (6)

1/4" (6)

3" (76)

3" (76)


Illus. 12—Models 661, 642, 632,685 and 695

131/4" (337)

4" (102)

1/4" (6)

3" (76)


Illus. 11—Models 611, 611G,650 and 650G



27

F U L L - S C A L ET E M P L AT E S

The full-scaleillustrations on thefollowing pagesenable you to under-stand some of theunique situationsyou may face as youplan for the installa-tion of the Built-Inmodels. Use theseillustrations astemplates forpanel and handlehardwareconsiderations.

P A N E L A N D H A N D L E P R O F I L E – F R A M E D A P P L I C A T I O N

11/4"(32) PANEL

1"(25) PANEL

1/4"(6) PANEL

1/2"(13) PANEL

3/4"(19) PANEL

OPTIONALEXTENDED

FULL-LENGTHHANDLE

STANDARD FULL-LENGTH

HANDLE

DOOR

1/4"(6) FRAMED PANEL

1"(25)

2"(51)

3"(76)

The full-scale illustration above showshandle placement for the framed appli-cation standard full-length handle andthe optional extended full-length handleshown in the dashed line.



28

P A N E L A N D H A N D L E P R O F I L E – O V E R L A Y A N D S T A I N L E S S S T E E L A P P L I C A T I O N

11/4" (32) PANEL

1" (25) PANEL

1/4" (6) PANEL

1/2" (13) PANEL

3/4" (19) PANEL5/8" (16) PANEL

DOOR

1/4" (6) APPROXIMATE THICKNESS OF WRAPPED STAINLESS STEEL DOOR

NOTE: FOR OVERLAY APPLICATIONS, OPTIONAL STAINLESS STEEL HANDLEMUST BE MOUNTED ON PANEL MINIMUM 5/8" (16) THICK.

1"2"

(51)3"

(76)

STANDARD STAINLESS STEEL HANDLE

The full-scale illustration above showshandle placement for the standardstainless steel handle on the wrappedstainless steel door and on overlaypanel applications shown in the dashedline.

IMPORTANT NOTE: For overlay applica-tions, the panel must be a minimum of5/8" (16) thick to support mounting thehandle hardware.

For overlay applications, mount doorhandles close to the opening edge ofthe door for ease of opening.


29

11 /4"

(32) PA

NEL

1" (2

5) PA

NEL

*1/4"

(6) P

ANEL

1 /2" (1

3) PA

NEL

3 /4" (1

9) PA

NEL

130˚ DOOR OPENINGWITH 2" (51) FILLER STRIP

(TOP VIEW)

OPTIONALFRAMED EXTENDED

FULL-LENGTH HANDLE

STANDARDFRAMED

FULL-LENGTHHANDLE

DOOR CLOSED

DOOR OPEN @ 130˚

HINGE

2" (51)

FILLER STRIP

MAIN FRAME

ALLOW FOR FILLER LAPBEHIND FLANGE

APPROXPROFILE OFSTAINLESS

STEEL DOORAND HANDLE

OVERLAY PANEL3/4" (19) THICK

(NOMINAL)

SUB-ZERO UNITSUB-ZERO UNIT

The full-scale illustration shows thepanel and handle profile for 130˚ dooropening with a 2" (51) filler strip.

Interference of door panels withhandles at maximum door swing mayrequire the use of an optional 90˚ doorstop available through your Sub-Zerodealer.

P A N E L A N D H A N D L E P R O F I L E – 1 3 0 ˚ D O O R O P E N I N G ( T O P V I E W )

*Approximate thickness of wrappedstainless steel door.



30

11/4

" (3

2) P

AN

EL

1" (2

5) P

AN

EL

*1/4

" (6

) PA

NE

L

1 /2"

(13)

PA

NE

L

3 /4"

(19)

PA

NE

L

11/4" (32)

11/2" (38)

13/4" (44)

0" (0)

1" (25)

2" (51)

21/4" (57)

21/2" (63)

23/4" (70)

3" (76)

31/4" (83)

31/2" (89)

1/4" (6)

1/2" (13)

3/4" (19) HINGE

OVERLAY PANEL 3/4" (19) THICK (NOMINAL)

DOOR CLOSED

DOOR OPEN @ 90˚

90˚ DOOR OPENING (TOP VIEW)

MAIN FRAME

NOMINAL OVERALL WIDTH OF SUB-ZERO

SUB-ZERO UNIT

237/8" (606) TO REAR OF SUB-ZERO

O V E R L A Y P A N E L A P P L I C A T I O N – 9 0 ˚ D O O R O P E N I N G ( T O P V I E W )

The full-scale illustrationshows what considera-tions you need to makefor overlay panel appli-cations and how theymay interact withadjacent cabinets andcountertops.

*Approximate thickness of wrappedstainless steel door.

S U B - Z E R O P R O D U C T S

L I M I T E D W A R R A N T Y

RESIDENTIAL USE ONLY

FULL FIVE YEAR SEALED SYSTEM WARRANTY

LIMITED SIXTH THROUGH TWELFTH YEAR WARRANTY ON THE SEALED SYSTEM

FULL TWO YEAR WARRANTY ON TOTAL PRODUCT*


For five years from the date of original installation, your Sub-Zero warranty covers all parts and laborto repair or replace any components that prove to be defective in materials or workmanship in thesealed system. The sealed system consists of the compressor, condenser, evaporator, drier and allconnecting tubing.

FULL TWO YEAR WARRANTY*

For two years from the date of original installation, your Sub-Zero warranty covers all parts and laborto repair or replace any part of the product, that proves to be defective in materials or workmanship.

LIMITED SIXTH THROUGH TWELFTH YEAR SEALED SYSTEM WARRANTY

From the 6th through the 12th year from the date of original installation, your Sub-Zero warrantycovers all parts that prove to be defective in materials or workmanship in the sealed system (partsonly). The sealed system consists of the compressor, condenser, evaporator, drier and all connectingtubing.

TERMS APPLICABLE TO EACH WARRANTY

All service provided by Sub-Zero under the above warranty must be performed by an authorizedSub-Zero service center, unless otherwise specified by Sub-Zero. Service will be provided in thehome during the normal business hours. This warranty applies only to products installed for normalresidential use. Details regarding a non-residential warranty are available upon request.

The warranty applies only to products installed in any one of the fifty states of the United States, theDistrict of Columbia or the ten provinces of Canada. This warranty does not cover any parts or laborto correct any defect caused by negligence, accident or improper use, maintenance, installation,service or repair, including but not limited to improper removal and reinstallation (whether in the unitor at a remote location) of the condensing unit.

THE REMEDIES DESCRIBED ABOVE FOR EACH WARRANTY ARE THE ONLY ONES THATSUB-ZERO WILL PROVIDE, EITHER UNDER THESE WARRANTIES OR UNDER ANY WARRANTYARISING BY OPERATION OF LAW. SUB-ZERO WILL NOT BE RESPONSIBLE FOR ANY CONSE-QUENTIAL OR INCIDENTAL DAMAGES ARISING FROM THE BREACH OF THESE WARRANTIESOR ANY OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so theabove limitation or exclusion may not apply to you. This warranty gives you specific legal rights andyou may also have other legal rights, which vary from state to state.

To receive parts and/or service and the name of the Sub-Zero authorized service center nearestyou, contact your Sub-Zero dealer, distributor or the Sub-Zero Customer Service Department,P.O. Box 44130, Madison Wisconsin, 53744-4130; check the Constant Care section of our website,subzero.com, or call 800-222-7820.

*Stainless Steel (classic, platinum and carbon) doors, panels, product frames and stainless interiorsurfaces are covered by a limited 60 day parts and labor warranty for cosmetic defects.

*Replacement water filter cartridges are not covered by the product warranty.

77

S U B - Z E R O O U T D O O R P R O D U C T S

L I M I T E D W A R R A N T Y

RESIDENTIAL USE ONLY


FULL ONE YEAR WARRANTY ON TOTAL PRODUCT*


For five years from the date of original installation, your Sub-Zero warranty covers all parts and laborto repair or replace any components that prove to be defective in materials or workmanship in thesealed system. The sealed system consists of the compressor, condenser, evaporator, drier and allconnecting tubing.

FULL ONE YEAR WARRANTY*

For one year from the date of original installation, your Sub-Zero warranty covers all parts and laborto repair or replace any part of the product which proves to be defective in materials or workman-ship.

TERMS APPLICABLE TO EACH WARRANTY

All service provided by Sub-Zero under the above warranty must be performed by an authorizedSub-Zero service center, unless otherwise specified by Sub-Zero. Service will be provided in thehome during the normal business hours. This warranty applies only to products installed for normalresidential use. Details regarding a non-residential warranty are available upon request.

The warranty applies only to products installed in any one of the fifty states of the United States,the District of Columbia or the ten provinces of Canada. This warranty does not cover any parts orlabor to correct any defect caused by negligence, accident or improper use, maintenance, installa-tion, service or repair, including but not limited to improper removal and reinstallation (whether inthe unit or at a remote location) of the condensing unit.

THE REMEDIES DESCRIBED ABOVE FOR EACH WARRANTY ARE THE ONLY ONES THATSUB-ZERO WILL PROVIDE, EITHER UNDER THESE WARRANTIES OR UNDER ANY WARRANTYARISING BY OPERATION OF LAW. SUB-ZERO WILL NOT BE RESPONSIBLE FOR ANY CONSE-QUENTIAL OR INCIDENTAL DAMAGES ARISING FROM THE BREACH OF THESE WARRANTIESOR ANY OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so theabove limitation or exclusion may not apply to you. This warranty gives you specific legal rights andyou may also have other legal rights which vary from state to state.

To receive parts and/or service and the name of the Sub-Zero authorized service center nearestyou, contact your Sub-Zero dealer, distributor or the Sub-Zero Customer Service Department,P.O. Box 44130, Madison Wisconsin, 53744-4130; check the Constant Care section of our website,subzero.com, or call 800-222-7820.

*Stainless Steel (classic finish) doors, panels, product frames and stainless interior surfaces arecovered by a limited 60 day parts and labor warranty for cosmetic defects.

78

The information and images in this guide are thecopyright property of Sub-Zero, Inc. Neither thisbook nor any information or images contained hereinmay be copied or used in whole or in part withoutthe express written permission of Sub-Zero, Inc.

©Sub-Zero, Inc. all rights reserved.

3758546 REV-D 8/2007

SUB-ZERO, INC.

P. O. BOX 44130

MADISON, WI 53744 -4130

800.222.7820

SUBZERO.COM

Documents

SUB-ZERO DESIGN GUIDE - Sub-Zero and Wolf … DESIGN GUIDE 3 IMPORTANT NOTE As you follow these instructions, you will notice warning and caution symbols. This blocked information