TCS T hermal C ontrol S olutions Barrel Heating and Cooling System For New or Existing Injection Molding Machines, Extruders and Blow Molding Machines. LOWER ENERGY COSTS. . . GUARANTEED! The SERVTEK TCS system consists of a radiant heating element embedded in our high-temperature fiber insulation. Radiant heat goes directly into the barrel and not into your plant, saving energy on the heaters and your air conditioning bill! Air cooling channels located under the heater quickly remove the heat and keep your barrel temperature under control energy – efficiently. This tightly controls the temperature of the barrel at virtually no maintenance cost. Guaranteed! SERVTEK - [email protected] 4165 Half Acre Road • Batavia, Ohio 45103 888-439-2491 • Fax 513-536-2212 • www.milacron.com UP TO 70% ENERGY SAVINGS! TCS T hermal C ontrol S olutions Save up to 70% on Energy Costs The SERVTEK TCS System uses the Rex Materials Group Pyrolite ® ceramic insulation. The high radiant energy release from the exposed element directs all heat into the barrel. The system does not depend on maintaining good contact to conduct heat into the barrel. Faster Response Time Unlike ceramic bands, aluminum-finned cast and water-cooled heaters that must first heat themselves before conducting heat into the barrel, the SERVTEK TCS heaters transfer heat immediately, providing faster response times. Conversely, when cooling, ambient air delivered directly to the barrel surface provides instant cooling. Tighter Temperature Control The SERVTEK TCS System controls barrel temperatures within +/- 1 ° F, resulting in less scrap and higher-quality product. Maintenance-Free Barrel Cooling Unlike water cooling with its high maintenance costs and downtime, the SERVTEK TCS System provides years of maintenance-free operation, resulting in significant cost savings. Demonstrated Payback in Less Than One Year! Factoring in energy savings, maintenance savings, less downtime, improved response time, increased productivity , and increased operator safety and comfort, the SERVTEK TCS System is quickly becoming the standard for plastics injection molders, blow molders and extruders. Go Green and Save With the TCS Barrel Heating System From © 2010 MILACRON LLC. MILACRON, SERVTEK, and the Globe Graphic are registered trademarks of MILACRON Inc. Printed in USA. 5/10 PM937

TCS Thermal Control Solutions - danda-eng.comdanda-eng.com/TCS brochure 2010-04.pdf · TCS Thermal Control Solutions Barrel Heating and Cooling System For New or Existing Injection

Download PDF Report

Upload
dinhbao
View
247
Download
0

Embed Size (px)

Citation preview

TCS Thermal Contro l So lu t ions

Barrel Heating and CoolingSystem For New or ExistingInjection Molding Machines,Extruders and Blow MoldingMachines.

LOWER ENERGY COSTS. . .GUARANTEED!

The SERVTEK TCS system consists of a radiant heating element embedded in our high-temperature fiber insulation. Radiant heat goes directly into the barrel and not into your plant, saving energy on the heaters and your air conditioning bill! Air cooling channels located under the heater quickly remove the heat and keep your barrel temperature under control energy – efficiently. This tightly controls the temperature of the barrel at virtually no maintenance cost. Guaranteed!

SERVTEK - [email protected] Half Acre Road • Batavia, Ohio 45103888-439-2491 • Fax 513-536-2212 • www.milacron.com

UP TO 70% ENERGY SAVINGS!

TCS Thermal Contro l So lu t ions

Save up to 70% on Energy CostsThe SERVTEK TCS System uses the Rex Materials Group Pyrolite® ceramic insulation. The high radiant energy release from the exposed element directs all heat into the barrel. The system does not depend on maintaining good contact to conduct heat into the barrel.

Faster Response TimeUnlike ceramic bands, aluminum-finned cast and water-cooled heaters that must first heat themselves before conducting heat into the barrel, the SERVTEK TCS heaters transfer heat immediately, providing faster response times. Conversely, when cooling, ambient air delivered directly to the barrel surface provides instant cooling.

Tighter Temperature ControlThe SERVTEK TCS System controls barrel temperatures within +/- 1° F, resulting in less scrap and higher-quality product.

Maintenance-Free Barrel CoolingUnlike water cooling with its high maintenance costs and downtime, the SERVTEK TCS System provides years of maintenance-free operation, resulting in significant cost savings.

Demonstrated Payback in Less Than One Year!Factoring in energy savings, maintenance savings, less downtime, improved response time, increased productivity , and increased operator safety and comfort, the SERVTEK TCS System is quickly becoming the standard for plastics injection molders, blow molders and extruders.

Go Green and Save With theTCS Barrel Heating System From

Page 2: TCS Thermal Control Solutions - danda-eng.comdanda-eng.com/TCS brochure 2010-04.pdf · TCS Thermal Control Solutions Barrel Heating and Cooling System For New or Existing Injection

• Faster and more effective air cooling directly on the barrel. • Does not depend on maintaining good contact with the barrel to conduct heat away.

• High radiant energy from exposed element provides faster response than conductive heater bands.

TCS Thermal Contro l So lu t ionsFor Injection Molding, Blow Molding Machines and Extruders

heaters are imbedded in high-temperature ceramic insulation.

TCS UP TO 70% ENERGY SAVINGS!FAST RETURN ON INVESTMENT!

Get Paid for Saving Energy Costs! You may be able to receive more than 50% of the SERVTEK TCS installed costswith state rebates, credits and incentives. Let us tell you how!

• Demonstrated Payback in Less than One Year• Up to 55% Faster Heat-up Time• Increased Productivity• Tighter Temperature Control• Faster Response Time• Controls Temperatures to +/- 1° F• Lowers Scrap Rate• Maintenance-Free Barrel Cooling• Extremely Long Life• Safe to Touch During Operation• No Maintenance or Downtime