Team Logo Here CanSat 2014 PDR: Team ### (Team Number and Name)1 CanSat 2014 Preliminary Design Review (PDR) Outline Version 1.2 Your Team # Here Your

Team LogoHere

CanSat 2014 PDR: Team ### (Team Number and Name) 1

CanSat 2014 Preliminary Design Review (PDR)

Outline Version 1.2

Your Team # Here

Your Team Name Here

Team LogoHere

(If You Want)

IMPORTANT PRESENTATION GUIDELINE:Teams should only present charts with this star icon during the

teleconference. Other charts should be skipped to save time; they will be reviewed by the judges off line.

Presentations are to be 30 minutes in length.


Presentation Outline

• Provide a simple outline of the presentation• If possible, indicate the team member(s) who will be

presenting each section• Terms:

– Container refers to the Re-entry Container component of the CanSat

– Payload refers to the Science Payload component of the CanSat

Presenter: Name goes here

Team LogoHere

(If You Want)


Team Organization

• Single slide listing the team members and their roles– If possible, please include year (freshman, sophomore, etc.) for reference– This only needs to be provided once for team members showing up multiple

times on the org chart• Good format is the use of an organization chart, such as below:


Team Lead(s)Name(s)

SubSystem 2 Lead(s)Name(s)

SubSystem 3 Lead(s)Name(s)

SubSystem 1 LeadName(s)

Faculty Advisor

Subsystem Engineer 1 Subsystem Engineer 2

Subsystem Engineer 1

Subsystem Engineer 1

Team LogoHere

(If You Want)


Acronyms

• Provide a list of acronyms used throughout the presentation– During presentations, do not read through these

acronyms• These are for reference only


Team LogoHere


Systems Overview

Presenter Name(s) Go Here

The purpose of this section is to introduce the reviewer to the overall requirements and configuration of the CanSat. This provides a basis for the details presented in the subsystem sections.

Team LogoHere

(If You Want)


Mission Summary

• Overview of the mission objectives• Indicate which one (1) selectable objective is being

attempted– Describe selection rationale

• Include any external objectives (personal, laboratory or sponsor, class, etc.) relevant to the design


Team LogoHere

(If You Want) System Requirement Summary

• Overview of system (mission) level requirements– Use bullets or a table to demonstrate an understanding of

the mission requirements• This chart may be expanded to multiple charts as

needed• The purpose of the chart is to demonstrate the team

understands the system-level requirements

CanSat 2014 PDR: Team ### (Team Number and Name) 7Presenter: Name goes here

Team LogoHere

(If You Want)


System Level CanSat Configuration Trade & Selection

• Present preliminary system-level concepts considered– What configurations were considered

• Present criteria for final configuration selection– Include discussion of why the final configuration was selected

• Include sketches and diagrams of various concepts considered– Diagrams of non-selected configurations can include sketches of

physical layouts (e.g. scans of hand sketches rather than CAD drawings)

• Include variations on CONOPS considered• Limit discussions to 1-2 slides per preliminary configuration

– Presentation of the material may be at a cursory level (hit the highlights)


Team LogoHere

(If You Want)


System Concept of Operations

• 1-3 slides providing overview of CanSat operations• Include:

– Launch and descent operations– Post-launch recovery and data reduction– Focus on selected configuration CONOPS

• Focus on how the CanSat will operate, not what everyone on the team will be doing (to be discussed at CDR)

• Simple flow diagrams and cartoons are a good way to present the CONOPS


Team LogoHere

(If You Want)


Physical Layout

• Diagram(s) showing physical layout of selected CanSat configuration

• Make sure to include:– Dimensions– Placement of major components– Relevant configurations

• Container, Payload, launch configuration, deployed, etc.

• The goal is to present the physical idea of what the CanSat will look like for reference prior to getting into details of the design


Team LogoHere

(If You Want)


Launch Vehicle Compatibility

• Discussion of how the CanSat is integrated into the rocket payload section

• Discussion of how the rocket payload section compatibility will be verified prior to launch day

• Include a dimensioned drawing that shows clearances with the payload section– Focus on launch configuration (Container + Payload)– Include all descent control apparatus (no sharp protrusions)– At PDR this may be allocated dimensions (if this is the case, these

should be requirements at the system and subsystem levels)– What is the clearance? (Leave margin to allow easy deployment!)

• Note:– In past years there were a large number of CanSats that did not

deploy from the payload sections of the rocket because of protrusions or because the CanSat was too wide to fit in the rocket


Team LogoHere


Sensor Subsystem Design


Team LogoHere

(If You Want)


Sensor Subsystem Overview

• One slide providing an overview of the CanSat sensor system– Include summary of the selected sensors (type &

models)– Include brief discussion of what the sensors are used for– Focus on selected component (not all components

trades)– Include overview of both Container and Payload sensors,

as applicable


Team LogoHere

(If You Want)


Sensor Subsystem Requirements


• Overview of sensor subsystem requirements– Use bullets or a table to demonstrate an understanding of

the requirements for this subsystem• This chart may be expanded to multiple charts as

needed• The purpose of the chart is to demonstrate to the

judges an understanding of the requirements that apply to the subsystem

• Clearly indicate:– Which Competition Guide Requirements are allocated to

this subsystem– Any derived requirements for the subsysytem

Team LogoHere

(If You Want)


Altitude Sensor Trade & Selection

• Summary of altitude sensor trade study and selection– Include both Carrier and Payload, as applicable


Team LogoHere

(If You Want)


Air Temperature Sensor Trade & Selection

• Summary of air temperature sensor trade study and selection– Include both Carrier and Payload, as applicable


Team LogoHere

(If You Want)


CameraTrade & Selection

• Summary of camera trade study and selection– Make sure camera meets all requirements


Team LogoHere

(If You Want)


3-Axis Accelerometer Sensor Trade & Selection

• SELECTABLE OBJECTIVE – ONLY REQUIRED IF SELECTED


Team LogoHere

(If You Want)


Rotor Rate SensorTrade & Selection

• SELECTABLE OBJECTIVE – ONLY REQUIRED IF SELECTED


Team LogoHere


Descent Control Design


Team LogoHere

(If You Want)


Descent Control Overview

• One slide providing an overview of the Container and Payload descent control system(s)

• Include overview of the selected configurations and components necessary

• Include diagrams outlining descent control strategy for various flight altitude ranges


Team LogoHere

(If You Want)


Descent Control Requirements


• Overview of subsystem requirements• Use bullets or a table to demonstrate an understanding

of the DCS requirements• This chart may be expanded to multiple charts as


judges that the team understands the system-level requirements


this subsystem– Any derived requirements for the subsystem

Team LogoHere

(If You Want)


Container Descent Control Strategy Selection and Trade

• Summary of container DCS strategy trade studies and selection

• Include:– Color selection– Shock force survival– DCS connections– Preflight review testability


Team LogoHere

(If You Want)


Payload Descent Control Strategy Selection and Trade

• Summary of Science Payload DCS strategy trade studies and selection– Include color selection– Preflight review testability


Team LogoHere

(If You Want)


Descent Rate Estimates

• Present estimates for the following CanSat configurations– Container + Payload post separation (prior to deployment

of the Payload)– Container following deployment of the Payload– Payload following separation from the Container

• Include discussion of – Calculations used – Assumptions

• This discussion can carry over to multiple slides if necessary


Team LogoHere


Mechanical Subsystem Design


Team LogoHere

(If You Want)


Mechanical Subsystem Overview

• One slide providing overview of the mechanical subsystem– Include overview of major structural elements, material

selection, and interface definitions– Include Container and Payload mechanical

configurations


Team LogoHere

(If You Want)


Mechanical Sub-System Requirements


• Overview of mechanical sub-system requirements– Use bullets or a table to demonstrate an understanding of



judges that the team understands the requirements that apply to this sub-system


this subsystem– Any derived requirements for the subsytem

Team LogoHere

(If You Want)


Egg Protection Trade & Selection

• Egg protection system trade studies and selection


Team LogoHere

(If You Want)


Mechanical Layout of Components Trade & Selection

• Key trade issues related to mechanical layout and component selection

• Structural material selection(s)


Team LogoHere

(If You Want) Material Selections

• Discussion of what materials will be used for the mechanical components and why


Team LogoHere

(If You Want)


Container - Payload Interface

• Describe how the Payload will be connected to and released (mechanically) from the Container– Include:

• Discussion of how descent control apparatus will be accommodated

• Diagrams• Method of operation

– Clearance between Payload and Container


Team LogoHere

(If You Want) Structure Survivability Trades

• For both Container and Payload discuss:– Electronic component mounting methods– Electronic component enclosures– Acceleration and shock force requirements and testing– Securing electrical connections (glue, tape, etc.)

• Consider required judge verification during pre-flight check in

– Descent control attachments


Team LogoHere

(If You Want)


Mass Budget

• Table(s) providing the following:– Mass of all components– Mass of all structural elements– Sources/uncertainties – whether the masses are

estimates, from data sheets, measured values, etc.– Total mass– Margin and method of correction at launch site

• Must clearly distinguish between Container and Payload masses– Include allocated mass for egg payload


Team LogoHere


Communication and Data Handling (CDH) Subsystem Design


Team LogoHere

(If You Want)


CDH Overview

• One slide providing overview of the CDH subsystem– Should include selected components (with brief mention

of what each component is for)


Team LogoHere

(If You Want)


CDH Requirements


• Overview of CDH sub-system requirements– Use bullets or a table to demonstrate an understanding of






Team LogoHere

(If You Want)

CanSat 2014 PDR: Team ### (Team Number and Name)

38

Processor & Memory Trade & Selection

• Include processor speed• Include data interfaces (types and numbers)• Include memory storage requirements, if applicable• Power management


Team LogoHere

(If You Want) Real-Time Clock

• Describe design for payload and container real-time clock functions– Hardware or software– Reset tolerance


Team LogoHere

(If You Want)


Antenna Trade & Selection

• Antenna selection criteria• Antenna range and patterns


Team LogoHere

(If You Want)


Radio Configuration

• Demonstrate an understanding of the protocol and configuration (e.g., mode and NETID) required to initialize and utilize the XBEE radio module

• Provide description of the impact those requirements have on the CanSat design

• Include transmission control– How is this managed during each mission phase?

• Note:– Communications failures have occurred often over the past several

years of the competition– You are encouraged to use your radios in all of your development

and testing to better ensure mission success• Ideally you have started working with the radio and communications

protocol


Start Radio Prototyping and Testing Early!

Team LogoHere

(If You Want)


Telemetry Format

• What data is included?– Include fields for bonus objectives

• Data rate of packets?– Continuous or burst

• How is data formatted?– Include example frames with complete descriptions– Does the presented format match the Competition Guide

requirements?


Team LogoHere


Electrical Power Subsystem (EPS) Design


Team LogoHere

(If You Want)


EPS Overview

• One slide providing overview of EPS components (with purposes)

• Include a diagram


Team LogoHere

(If You Want)


EPS Requirements


• Overview of EPS subsystem requirements• Use bullets or a table to demonstrate an understanding

of the mission requirements• This chart may be expanded to multiple charts as





Team LogoHere

(If You Want)


Electrical Block Diagram

• High-level schematic (not down to the resistor level) showing power connections– Include required voltages– Include all major components

• Include overview of how power will be controlled and verified externally without disassembling the CanSat– I.e., an easily accessible external switch

• Include diagrams for Container and Payload in one or two slides

• Umbilical power source for use in test and safety inspection


Team LogoHere

(If You Want)Payload Power SourceTrade Study

• Describe payload power source and considered options, including:– Power source– Rationale– No Li-polymer cells allowed


Team LogoHere

(If You Want)


Power Budget

• Power budget in tabular format which includes:– Power consumption (W) of all components– Expected duty cycles for all components– Source/uncertainty for each line item

• Estimate, data sheet, measurement, etc.

– Total power consumed (mAh)– Power sources and total power available– Power storage devices and strategy

• Graphical representation of charge / discharge cycles

– Margins• Include potential one hour wait on the launch pad for the

Container


Team LogoHere

(If You Want)


Power Bus Voltage MeasurementTrade & Selection

• Discuss voltage measurements technique and circuit


Team LogoHere


Flight Software (FSW) Design


Team LogoHere

(If You Want)


FSW Overview

• Overview of the CanSat FSW design• Should discuss

– Basic FSW architecture– Programming languages– Development environments– Brief summary FSW tasks


Team LogoHere

(If You Want)


FSW Requirements


• Overview of mechanical sub-system requirements• Use bullets or a table to demonstrate an understanding

of the mission requirements• This chart may be expanded to multiple charts as




this subsystem– Any derived requirements for the subsytem

Team LogoHere

(If You Want)


CanSat FSW State Diagram

• Software state diagrams for Payload and Container (as applicable) defining the states and transition conditions of the flight software

• Include:– Sampling of sensors (including rates)– Communications (command and telemetry)– Data storage (if applicable)– Mechanism activations– Major decision points in the logic– Power management

• FSW recovery to correct state after processor reset during flight– What data is used to recover?


Team LogoHere

(If You Want)


Software Development Plan

• A common CanSat problem is late software development

• Present a slide describing the plan for software development and plans to reduce the risk of late software development

• Include:– Prototyping and prototyping environments– Software subsystem development sequence– Development team– Test methodology


Team LogoHere


Ground Control System (GCS) Design


Team LogoHere

(If You Want)


GCS Overview

• Include a simple context diagram showing major components (computers, antenna, adaptors, etc.)


Team LogoHere

(If You Want)


GCS Requirements


Examples of requirements to include:• Antenna construction and placement (field-of-view requirements)• Computational requirements• Analysis SW requirements• Mission operations sequence of events

• Overview of GCS requirements• Use bullets or a table to demonstrate an understanding

of the requirements for the GCS• This chart may be expanded to multiple charts as


judges that the team understands the requirements that apply to the GCS

Team LogoHere

(If You Want)


GCS Antenna Trade & Selection

• Make sure to include:– Antenna construction, placement, and coverage

• Diagram is recommended• Note: attaching to tent structure is not allowed

– Antenna mast height and mounting strategy• Launch day construction• Launch day verification of height• If not fixed antenna, discuss how hand held antenna will be used

– Distance link predictions and margins


Team LogoHere

(If You Want) GCS Software

• Telemetry display prototypes • Commercial off the shelf (COTS) software packages

used• Real-time plotting software design• Data archiving and retrieval approach• Command software and interface• Telemetry data recording and media presentation to

judges for inspection• Describe .csv telemetry file creation for judges


Team LogoHere


CanSat Integration and Test


Team LogoHere

(If You Want)


CanSat Integration and Test Overview

• 3-5 slides• Discussion of how the CanSat subsystems will be integrated• Discussion of system-level tests to be performed on the integrated

CanSat• At PDR this should include concepts for how subsystems will be

integrated– Sequence (which subsystems are needed prior to others)– Test equipment necessary– Test environments necessary

• The goal(s) at PDR are– Get teams thinking about how to put all the pieces together– Get teams thinking about how to test the integrated assembly to

make sure it works as a unit


Team LogoHere


Mission Operations & Analysis


Team LogoHere

(If You Want)


Overview of Mission Sequence of Events

• Preliminary launch-day sequence of events– Should start w/arrival at the launch site and proceed

through recovery and data analysis• Include:

– Flow chart of events– Team member roles and responsibilities– Antenna construction and ground system setup– CanSat assembly and test

• Preliminary at PDR


Team LogoHere

(If You Want)


Mission Operations Manual Development Plan

• Discuss development and content of the Missions Operations Manual for your CanSat


Team LogoHere

(If You Want)


CanSat Location and Recovery

• Discuss how you will find your CanSats in the field– Discuss Container and Payload recovery– Color selection of visible components– CanSat return address labeling

Presenter: Name goes herePresenter: Name goes here

Team LogoHere

CanSat 2014 CDR: Team ### (Team Number and Name) 66

Requirements Compliance


The purpose of this section is to summarize and cross reference the compliance to the CanSat Competition Mission Guide requirements.

Team LogoHere

(If You Want) Requirements Compliance Overview

• State current design compliance to requirements• Summarize content of the detailed slides that follow• If the design does not comply to the requirements, that

is a serious issue – why?

CanSat 2014 CDR: Team ### (Team Number and Name) 67Presenter: Name goes here

Team LogoHere

(If You Want)

68

Requirements Compliance(multiple slides, as needed)

• Provide a table demonstrating compliance to all competition base requirements– Use the following format in as many slides as required

CanSat 2014 PDR: Team ### (Team Name)

RqmtNum

RequirementComply / No

Comply / Partial

X-Ref Slide(s) Demonstrating

Compliance

Team Commentsor Notes

1Total mass of CanSat, container, and all descent control devices shall be 700 grams. Mass shall not vary more than +/-10 grams.

Comply x, y, z Everything should be green by CDR.

2The cansat must be installed in a container to protect it from deployment out of the rocket.

-- -- --

3The container shall fit inside the cylindrical payload section of the rocket defined by the cylindrical payload envelope of 130 mm x 250 mm length control system including the descent

Partial Medium problem: why?

4The container must use a descent control system. It cannot free fall.

No Comply Big problem: why?

5The container shall not have any sharp edges that could cause it to get stuck in the rocket payload section.

6 The container must be a florescent color, pink or orange.

Use the Green (Comply), Yellow (Partial Compliance), and Red (No Comply) color codes as shown in the examples above for each requirement


Team LogoHere


Management


Team LogoHere

(If You Want)


CanSat Budget – Hardware

• Provide a table listing the costs of the CanSat flight hardware

• Table should include– Cost of major components and hardware– Indication of whether these costs are actual, estimates,

or budgeted values– Indication of hardware re-use from previous years

• The current market value for re-used components should be included

• Note: re-used flight hardware has been known to be more likely to fail


Team LogoHere

(If You Want)


CanSat Budget – Other Costs

• Table(s) (same format as Hardware Budget) showing– Ground control station costs– Other costs

• Prototyping• Test facilities and equipment• Rentals• Computers• Travel

– Income• Sources of project income

• The goal(s) of this budget are– To provide an understanding of the overall design and development costs– Get the teams thinking about the overall costs including necessary funds for

travel– Identify shortfalls in the budget that require attention

• In the past some teams have not been able to attend the competition due to a lack of funds

• If caught early enough, there are a number of resources for funding that may available to teams

– THE COMPEITION DOES NOT PROVIDE ANY DEVELOPMENT FUNDING OR DONORS


Team LogoHere

(If You Want)


Program Schedule

• Overview of development schedule to include– Competition milestones– Academic milestones and holidays– Major development activities– Component/hardware deliveries– Major integration and test activities and milestones

• The schedule should be “wrapped up” to 1-2 levels– Show high-level tasks only in order to make the schedule readable– It is recommended a schedule at lower levels is developed in order to provide the

team with tools for tracking progress and assessing trouble areas• The goals of this schedule are to

– Provide a tool for the team to track progress of CanSat design and development– Provide tool for judges to assess trouble areas and offer ways for the team to best

meet the objectives of the competition• A one page Gantt summary chart showing task start and stop dates and durations

shall be presented– Schedule should include linkages between tasks to provide the team with an idea of

what happens in the overall flow when milestones are not met on time• Make sure the schedule is readable in the presentation

– This may require the schedule to be broken between multiple slides• Failure to do so will result in a loss of points


Team LogoHere

(If You Want)


Conclusions

• Presentation summary and conclusions• In general include the following:

– Major accomplishments– Major unfinished work– Why you are ready to proceed to next stage of

development


Team LogoHere


Presentation Scoring & Additional Information

The following slides provide additional information regarding presentation scoring, as well as

recommendations for the presentations and slides

Do Not Include the Following Charts in the Presentations

Team LogoHere

(If You Want) Presentation Scoring

• Each slide in this template is scored on a scale of 0 to 2 points– 0 = missing or no compliance to the

intent of the requirement– 1 = topic incomplete or partial

compliance to requirement(s)– 2 = complete and demonstrates

requirement(s) met• Each section of the presentation

(System Overview, Sensor Subsystems, etc.) is weighted according to the table

• Each team will receive a link to a summary score sheet that will contain all their competition scores

CanSat 2014 PDR: Team ### (Team Name) 75

CDR Scoring

System Overview 5%

Sensor Subsystem Design 10%

Descent Control Design 10%

Mechanical Subsystem Design 10%

Communication and Data Handling Subsystem

10%

Electrical Power Subsystem Design 10%

Flight Software Design 10%

Ground Control System Design 10%

CanSat Integration and Test 5%

Mission Operations and Analysis 5%

Requirements Compliance 5%

Management 5%

Overall Presentation Quality 5%

Total: 100%

Team LogoHere

(If You Want)


PPT Template Use

• All teams shall use this presentation template• Team logos

– A team logo can be inserted into the placeholder location (and size) on the master slide

– If no logo is to be used, remove the placeholder from the master slide• Team numbers in the footer should be updated in the footer information

view– REMEMBER TO PUT YOUR TEAM NAME AND NUMBER IN THE FOOTER– Team names are optional – if no team name is used, please delete from

footer text• On each slide, replace the “Name goes here” in the bottom left corner with the

name of the person(s) presenting that slide– This will allow the judges to know the person to address any questions or

comments to

Team LogoHere

(If You Want)


Trade Studies

• The following recommendations are made with regards to trade studies and selections– Tabular formats listing configurations/components being considered are

helpful– Need to include a discussion of the criteria being used to make the selection

• What are the components/configurations being assessed on• How are values ascribed to the criteria

– Are high values good or low values (if a ranking system is chosen)– Why are different ranking selected

• Data sources for information impacting the criteria and rankings– Make sure it is clear which final component/configuration was selected

• Teams using hardware from previous years are still expected to do a trade to ensure the components are the most appropriate for the task– Already having a component or past experience with a component can be

criteria used in the trade space– Note that in past years re-used components have a higher failure rate

• The same format (whether table are used or not) and criteria (consistent rankings, etc.) be use for all trades to make it easier to review the various trades in a timely manner

Team LogoHere

(If You Want)Presentation Template Update Log (Do not include in presentation)

• 1.0 Initial version for 2014• 1.1 Included real-time clock slide• 1.2 Minor corrections for consistency with CDR

– Relocate requirements compliance slide(s) to before Management


Documents

Team Logo Here CanSat 2014 PDR: Team ### (Team Number and Name)1 CanSat 2014 Preliminary Design Review (PDR) Outline Version 1.2 Your Team # Here Your