6
COMPACT RUGGED POWERFUl Ideal for night safety Fits in purse, car glove compartment, pocket Tough aircraft-grade anodized aluminum body Lightweight, durable, compact design Is corrosion & wear resistant Emergency strobe light Alert feature at the touch of a button Scratch resistant polycarbonate lens Resists mild scrapes and scratches and Uv inhibitors protect lens from yel/owing ·Weather resistant Suitable for wet climate use High & low beam Push-button instantly selects desired light intensity Impact resistant Drop tested to withstand impact from 3.2 ft. (1 m) Cree is a Registered Trademark of Cree, Inc. USPatent Pending LEDmade in China Complies with ANSI Standards MADE IN CHINA MUL TI-FUNCTION PUSH-BUTTON SWITCH LOW LIGHT OUTPUT HIGH LIGHT OUTPUT EMERGENCY STROBE 0) OFF 0 breakout view of flashlight

Techlite Lumen Master 200 Lumens Flashlight

Embed Size (px)

DESCRIPTION

Techlite Lumen Master 200 Lumens High-Intensity CREE XPG L.E.D. Tactical Flashlight, 3 Pack. Product packaging and user guide.

Citation preview

Page 1: Techlite Lumen Master 200 Lumens Flashlight

COMPACT •RUGGED • POWERFUl• Ideal for night safety

Fits in purse, car glove compartment, pocket

•Tough aircraft-gradeanodized aluminum bodyLightweight, durable, compact designIs corrosion & wear resistant

•Emergency strobe lightAlert feature at the touch of a button

•Scratch resistantpolycarbonate lensResists mild scrapes and scratches andUv inhibitors protect lens from yel/owing

·Weather resistantSuitable for wet climate use

•High & low beamPush-button instantly selects desired light intensity

• Impact resistantDrop tested to withstand impact from 3.2 ft. (1m)

Cree is a Registered Trademark of Cree, Inc.USPatent PendingLEDmade in ChinaComplies with ANSI StandardsMADE IN CHINA

MUL TI-FUNCTIONPUSH-BUTTON SWITCH

LOW LIGHT OUTPUT •

HIGH LIGHT OUTPUT •

EMERGENCY STROBE 0)OFF 0

breakout view of flashlight

Page 2: Techlite Lumen Master 200 Lumens Flashlight

WEATHER IMPACT PEAK HIGH BEAM BEAM RUN TIME RUN TIMERESISTANT RESISTANT INTENSITY INTENSITY RANGE HIGH BEAM LOW BEAM

~1.09yd/1m @ \', 164yd/lS0m C9 C9

~~~~ v. ~200'- LO ITMJART.60916000 cd LUMENS 1 HOUR 4 HOURS 111111111111 111111111111

FL1 STANDARD

4"897

650

Page 3: Techlite Lumen Master 200 Lumens Flashlight

POllycarbonate [elVacuum !Plated R,efloctor

Alrcralt-GradAnodized Aluminum Body

- MULTI-FUNCTION, FlUSH-BUTTON SWITCH

Note:This Q.; evice complies with Pant15 of tn~ Fql Hules.Operation is subject to the following two c~nditlons:(1)This device may not cause harmful interj,'rence,and(2)This device must accept any interferen~ireceived,includil)9' interference that may cause un~eslredoperation.

Includes 3 AA(4Batteries

Page 4: Techlite Lumen Master 200 Lumens Flashlight
Page 5: Techlite Lumen Master 200 Lumens Flashlight

Tactical FlashlightITM.IART.609650Instructions~iiiillJiII

1. To open: Unscrew cap in counter-clockwise direction.2. insert batteries into the battery hoider. insert batteries

with correct polarity as shown on the battery holder.3. To close: Screw cap in clockwise direction.4 ._Ere$_s rubJw. R.ush:b.u1tO.Dutllo.ulig~h.lLt_~~=NOTE: Do not mix old and new batteries.

G) 0r0 ....,Q

1-

-& iii

Press the switch at rubber end cap to operatea) Press one time for 30% lightb) Press two times for 100% lightc) Press three times for flashing strobe lightd) Press and hold switch for momentary-on light

Page 6: Techlite Lumen Master 200 Lumens Flashlight

Always purchase the correct size and grade of battery mostsuitable for the intended use. Do not mix alkaline, standard(carbon-zinc), or rechargeable (nickel-cadmium) batteries.Replace all batteries of a set at the same time.Clean the battery contacts and also those of the device priorto battery installation.Ensure the batteries are installed correctly with regard to polarity(+and-).-Remove batteries from equipment which is not tobe used for an extended period of time.Remove used batteries promptly.

fmIi)Changes or modifications not approved by the party responsiblefor compliance could void user's authority to operate the equipment.

This equipment has been tested and found to comply with the limitsfor a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipmentgenerates, uses and can radiate radio frequency energy and, if notinstalled and used in accordance with the instructions, may causeharmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or televisionreception, which can be determined by turning the equipment off andon, the user is encouraged to try to correct the interference by one ormore of the following rnaasJJLes.:__-- Reorient or relocate the receiving antenna.-- Increase the separation between the equipment and receiver.-- Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.-- Consult the dealer or an experienced radio/TV technician for help.

Customer Service: 1·888·910·2280Hours: M·F 8AM to 5PM Pacific TimeE·mail Address: [email protected]·flashlight.com