8/9/2019 TM 9-1005-210-35P

1/25

*TM 9-1005-210-35PDEPARTMENT OF THE ARMY TECHNICAL MANUAL

FIE LD AND DEPOT MAINTENANCEREPAIR PARTSANDSPECIALTOOL LISTS

FORCARBINE, CALIBER .30: Ml ANDM2

Headquarters, Department of th e Army, Washington25, D.C.17 Octo ber 196 3

SECTIO N I. PR E FAC E .......................II. REPAIR PARTS AN D SPECIAL TOOLSRepair Parts for:Carbine, caliber .30Ml and M 2 .......Stock group....................Trigger housing group (M l only) ......Trigger housing group (M 2 only) ......Bolt assembly ..................Barrel and receiver group ..........Oiler, carbine' ...................Cleaningrod ...................Special Packaging Materiel ........;Miscellaneous Equipment ..........Tools and Equipment Authorized for UnitReplacement for Lower Echelon .....Tools and Equipment .............

Page

1

791012141516161616

1718

SECTION IPREFACE

1. G enera la . This manual is a list of:(1 ) Items authorized for initial stock-age at fieldmaintenance and supplysupport activities. A lso listed areadditional repair parts which maybe requiredforperformingauthorized fieldmaintenancebut areto berequisitioned as required.(2 ) Repair parts recommended for th eoverhaul of one hundredcom

ponentsorenditems of equipment.Also listed are additional repairparts which may be required forperforming authorized depotmaintenancebut are to be requisitioned, when required, if n otobtainablefrom reclamation, controlled cannibalization, fabrication, or localprocurement.

b. For pricesof items listedherein, seethe appropriate supply manual SM 9-2-1Thism anual supersedes DA Sup pl y M anu al O RD 8 SN L B28 , 23 M ay 195 7 and ORD 9 SN L B28, 10 August 1949 ,including Cl, 14 Ju ly 1954.

8/9/2019 TM 9-1005-210-35P

2/25

and SM 9-2-2. Prices of items that aretheresponsibility of commodity commandsmaybe obtained from theappropriate type2 supply manuals for those services.c. Additional applications of items inthis manual are listedinthe supply manualof the SM 9-3 series.

2. Requisition Notesa. When requisitioning an item, the requisitioning agency will order the listeditem. However, the commodity commandwill take necessary action to issue theexhaust stock itemuntil stock is exhausted,whether it be an individual item, kit, set,or assembly.b. Requisitions for replacementof itemsthat are the responsibility of commoditycommands will be submittedto the commodity command indicated in column la,Materiel Numerical Code.c. If the exact item requisitioned is notfurnished or if otheraction is necessary,the exact nature of the action taken by thecommodity command will be indicated bystandardsymbols on prescribed forms.3. Explanation of Columns

a. Source, Maintenance and Recovera-bilityCode (Col. 1).(1 ) Materiel numerical code (col. la).This column indicatesthe materielnumerical code, other than Ordnance materiel, assigned supplyresponsibility for the listed item.When no code is indicatedthe itemis considered Ordnance. Commoditycommand responsible for supplyof items in this list is:Code Type Materiel10 Quartermaster Materiel(2 ) Source (col. Ib). This column indi

cates the selection status andsource for the listed item. Sourcecodes usedinthis list are:Code Explanation

P Requisition from thedepotsystem of theresponsible commodity command (applies to high mortality parts).

Code ExplanationPI Requisition from thedepot system of theresponsible commodity command (applies to low mortality parts).

(3 ) Maintenance level (col. Ic). Thiscolumn indicates the lowestmaintenance echelon authorized toinstall the listed item. Maintenancelevel codes used in this list are:

Code ExplanationO Organizational maintenance (1st & 2dechelon).F Field maintenance(4th echelon).D Depot maintenance(5th echelon).

(4 ) Recoverability (col. Id). Thiscolumn indicateswhetherunserviceable items should be returned forrecovery or salvage. When no codeis indicated, the item will be considered expendable. Recoverabilitycodes used in this list are:Code ExplanationR Items which are economically repairableat field maintenanceactivities (3d and

4th echelon) and arenormally furnishedby supply on an exchange basis. Gageswill be forwarded toGage Laboratory inaccordance with SB9-75.b. Federal StockNumber (C ol. 2). Thiscolumn indicates theFederal stocknumberwhich has been assigned by the CatalogingDivision, Defense Logistics ServicesCenter.c. Description (Col. 3). This columnindicates the Federal itemname (shown incapital letters) and anyadditionaldescrip

tion required for supply operations. Theabbreviations "w/e" (with equipment),when used as a portion of the nomenclature, indicates that the end item (majoritem) or major combination includes allarmament, equipment, accessories, andrepair parts issued with the item. Thecommodity command or manufacturer'spart number isalso included for reference.

8/9/2019 TM 9-1005-210-35P

3/25

d. U nit of Issue (Col. 4). This column indicates the quantity to be requisitioned.e. Quantity Incorporated inU nit (Col. 5).This columnindicates thenumber of timesthe listed item is used in the functionalunit.f. 15-Day Maintenance Allowance(C ol. 6).(1 ) Fieldmaintenance per 100 equipments. This columnindicatesrepairpart allowance factors forfield maintenance. These factorsrepresent the estimated averagequantities required to providemaintenance and, whereapplicable,supplysupport for 1 00 equipmentsfor a 15-day periodunder combatconditions. The exact quantity authorized must be computed asinstructedin (2 ) below.(a ) W hen an allowance factorisinclosed inparentheses, the itemis designated as a "combat essential item of a criticalnature"andmust be stocked at alltimes,regardlessof demand.(b) Additional repair parts whichmay be required for performingauthorized maintenance but notauthorized for stockage in theprescribed load, are indicated by

an asterisk (* ) . These items areto be requisitioned as requiredfor immediate use only.(c) Where no quantity is shown, reference should be made to thefirstappearance of th e item asindicated in the descriptioncolumn.Note. The 15-day level is not applicable to special tools fo r field anddepotmaintenance.

(2 ) Computation of authorized quantities. To compute th e exactquantities authorizedusing theallowance factors multiply thenumberof equipmentssupported bythe allowance factor. Then divideby 1 00.Example: If th enumber ofequipmentssupportedis.. 30

and the allowancefactorfor 1 00 equipmentsis.....xl.9The resultingproduct is.... 57.0Divide this by 1 00 (this may beaccomplished by moving the decimal pointtwoplaces toward the leftthus: .570 or 0.570. W hen the resulting fractional value is .5 orlarger, itwill be roundedoff tothenext higher whole number.Example: If 1.77 is obtained, aquantity of 2 is authorized. W hen theresulting fractionalvalue isbelow,S , itwill berounded to thenext lower whole number.Example: If 3.4 is obtained, aquantity of 3 is authorized.g. Depot Maintenance Guide per 100Equipments (C ol. 7).(1 ) This column indicates repairpartallowance factors fordepotmaintenance. These factors representrecommended quantities requiredto overhaul 1 00 components or end items of equipment.

(2 ) The exact quantityauthorized mustbe computed as instructed in/(2)above. Additional repair partswhich may be required for performing authorized maintenanceare indicated by an asterisk (*) .These items are to be requisitioned, when required for immediate use only. W here no quantityisshown, reference should be madeto the first appearanceof theitemas indicated in the "description"column.Note. The 15-day level is not applicable to tools and equipment fo r .field anddepot maintenancepersonnel.

h. Illustration(C ol. 8).(1 ) This column indicates the figurenumber of the illustration thatdepicts the listed item. Whenmore than one item appears on

8/9/2019 TM 9-1005-210-35P

4/25

an illustration, the item numberis also indicated.(2 ) Items that appear on the illustrations and in the legends of theillustrations but which are notlisted in the tabular listing arenon-supply parts and are notauthorized.4. AbbreviationsAbbreviation Explanationassy ................ssembly (ies)cal ................ aliber (s)cc .................. ubic centimeter (s)cham ................hamferdeg ................. egree(s)dia .................iameter (s)fl-fil-hd ..............lat fillisterheadgnd ................. roundid ..................nside diameter (s)In. .................nch (es)lb.................. ound (s)lg ..................ength (long)max ................aximummfr .................anufacturer (s)min ................. inute (s)od ..................utside diameter (s)phos-fin .............. hosphate finishS .................. teel

sq ..................quarestk .................tocksyn-ru ...............ynthetic rubberthk .................hick (ness)TPI.................hreads per inchVC-.................volatile corrosioninhibitorw..................with5. Sugges tions and Recommendat ions

The direct reporting of errors, omissions and recommendations for improvingthis equipment manual by the individualuser is authorized and encouraged. DAForm 2028 will be used for reportingthese improvements. The form may becompletedusing pencil, penor typewriter.DA Forms 2028 will be completed in triplicate and forwardedto: CommandingGeneral, Headquarters, U.S. ArmyWeap ons Command, RockIslandArsenal, RockIsland, Illinois, ATTN:AMSWE-SMM. Oneinformation copy will be provided to theindividual's immediate supervisor (e.g.,officer, noncommissionedofficer, supervisor, etc.).

8/9/2019 TM 9-1005-210-35P

5/25

L E F T FR O N T V I E W

R IGHT R E A R VIEW

Figure 1. Caliber .30 carbine Ml with sling and oiler.ORD F5479

8/9/2019 TM 9-1005-210-35P

6/25

L E F T FRONT VIEW

RIGHT R E A R VIEW

Figure . Caliber .30 carbine M2 with sling and oiler.OR D F5-J80

8/9/2019 TM 9-1005-210-35P

7/25

8/9/2019 TM 9-1005-210-35P

8/25

1 4

O RD F5495

8/9/2019 TM 9-1005-210-35P

9/25

8/9/2019 TM 9-1005-210-35P

10/25

8/9/2019 TM 9-1005-210-35P

11/25

O R D F6 3 9 9

11

8/9/2019 TM 9-1005-210-35P

12/25

8/9/2019 TM 9-1005-210-35P

13/25

1 3

13

8/9/2019 TM 9-1005-210-35P

14/25

8/9/2019 TM 9-1005-210-35P

15/25

8/9/2019 TM 9-1005-210-35P

16/25

16

8/9/2019 TM 9-1005-210-35P

17/25

17

8/9/2019 TM 9-1005-210-35P

18/25

8/9/2019 TM 9-1005-210-35P

19/25

19

8/9/2019 TM 9-1005-210-35P

20/25

8/9/2019 TM 9-1005-210-35P

21/25

1 1

ORD F5502

21

8/9/2019 TM 9-1005-210-35P

22/25

1 2

ORD F5503

8/9/2019 TM 9-1005-210-35P

23/25

O R D F 6 3 0 2

2

8/9/2019 TM 9-1005-210-35P

24/25

ORDFS5M

fe i tt g&ayj ' i itf '1 I ^ ^Q RD F568 6

**>'/*9MAX.1( Wt

. S E T Afisres

MAX.

8/9/2019 TM 9-1005-210-35P

25/25

Official:J. C.

USAMOCOM (2)

U.S. GOVERNMENT PRINTING OFFICE : O826-O56