9
GRUNDFOS DATA BOOKLET TP, TPD, TPE, TPED, TPE2, TPE2 D, TPE3, TPE3 D In-line circulator pumps 50 Hz Lenntech

TP, TPD, TPE, TPED, TPE2, TPE2 D, TPE3, TPE3 D · Performance range TP, TPD, TPE, TPED, TPE2, TPE2 D, TPE3, TPE3 D Performance range, 2-pole, PN 25 TM06 6533 4217 20 30 40 50 60 70

  • Upload
    others

  • View
    30

  • Download
    0

Embed Size (px)

Citation preview

GRUNDFOS DATA BOOKLET

TP, TPD, TPE, TPED, TPE2, TPE2 D, TPE3, TPE3 D

In-line circulator pumps50 Hz

Lenntech

TP

Se

ries

10

0 a

nd

20

0 p

um

ps

TP, TPD, TPE, TPED, TPE2, TPE2 D, TPE3, TPE3 D

6. TP Series 100 and 200 pumps

Fig. 9 TP Series 100 and TP Series 200

Technical data

ConstructionGrundfos TP Series 100 and Series 200 pumps are single-stage, close-coupled pumps with in-line inlet and outlet ports of identical diameter.

The pumps are fitted with a fan-cooled asynchronous motor. Motor and pump shafts are connected via a rigid two-part coupling.

TP Series 100 pumps with union connection are available as single-head, TP, pumps.

TP Series 200 pumps are available as single-head, TP, and twin-head, TPD, pumps.

TP Series 200 pumps have PN 6 or PN 10 flanges.

The pumps are fitted with an unbalanced mechanical shaft seal.

The pumps are of the top-pull-out design, that is you can remove the power head (motor, pump head and impeller) for maintenance or service while the pump housing remains in the pipes.

The twin-head pumps are designed with two parallel power heads. A flap valve in the common outlet port is opened by the flow of the pumped liquid and prevents backflow of liquid into the idle pump head.

As radial and axial forces are absorbed by the fixed bearing in the motor drive-end, the pump requires no bearing.

The pumps are fitted with high-efficiency motors.

Pumps with a bronze or stainless-steel pump housing are suitable for circulation of domestic hot water.

Materials

TP Series 100

Fig. 10 Sectional drawing of TP Series 100 with union connection

Material specification, Series 100

GrB

28

50

- G

r82

61

Flow rate: Up to 90 m3/hHead: Up to 27 mLiquid temperature, TP Series 100: -25 to +120 °CLiquid temperature, TP Series 200: -25 to +140 °CMaximum operating pressure: Up to 16 barDirection of rotation: Counterclockwise

TM

03

12

10

26

12

Pos. Component Material EN/DIN

1 Pump housingCast iron EN-GJL-150, EN-GJL-200, stainless steel

EN-JL 1020EN-JL 10301.4308

2 Impeller Composite PES/PP 30 % GF

3 Shaft Stainless steel 1.4057

4 Coupling Cast iron EN-GJL-400 0.7040

5 Pump headCast iron EN-GJL-200, stainless steel

EN-JL 10301.4308

Secondary seals EPDM

Rotating seal face

Silicon carbide

Stationary seatCarbon (resin-impregnated), silicon carbide

TP

Se

rie

s 1

00

an

d 2

00

pu

mp

s

TP, TPD, TPE, TPED, TPE2, TPE2 D, TPE3, TPE3 D

TP Series 200

Fig. 11 Sectional drawing of TP Series 200 with flange connection

Material specification, Series 200

Mechanical shaft sealTwo types of unbalanced mechanical shaft seal are available as standard:

• BQBEThe BQBE shaft seal is a rubber bellows seal with silicon carbide/carbon seal faces and secondary seals of EPDM.

• BQQEThe BQQE shaft seal is a rubber bellows seal with silicon carbide/silicon carbide seal faces and secondary seals of EPDM.

For more information about common pumped liquids with recommended shaft seals, .

Shaft seal specification

Special shaft seals are available for partly conditioned water or other liquids containing abrasive or crystallising particles..

ConnectionsTP Series 100 pumps with union connection have inlet and outlet union threads to ISO 228-1.

TP Series 200 pumps up to DN 65 are fitted with combination flanges PN 6 / PN 10. DN 80 or DN 100 pumps have either PN 6 or PN 10 flanges. You can connect all flanges to flanges in accordance with EN 1092-2 and ISO 7005-2.

Features and benefitsTP Series 100 and Series 200 pumps have these features and benefits:

Optimised hydraulics for high efficiency

– Reduced power consumption.

High-efficiency motors

– TP pumps are fitted with high-efficiency motors. High-efficiency motors offer reduced energy consumption. TP pumps are primarily fitted with motors that meet the legislative requirements of the EuP IE3 grade. For further information, .

Top-pull-out design

– Easy dismantling in case of service.

In-line design

– Contrary to end-suction pumps, in-line pumps allow straight pipes and thus often reduced installation costs.

Pump housing and pump head are electrocoated to improve the corrosion resistance

– Electrocoating includes:1. Alkaline cleaning.2. Pretreatment with zinc phosphate coating.3. Cathodic electrocoating, epoxy.4. Curing of paint film at 200 to 250 °C.For low-temperature applications at a high humidity, Grundfos offers TP pumps with extra surface treatment to avoid corrosion. These pumps are available on request.

Stainless-steel impeller and neck ring

– Wear-free operation with high efficiency.

TM

03

12

11 4

71

5

Pos. Component Material EN/DIN

1 Pump housingCast iron EN-GJL-250, bronze CuSn10

EN-JL 10402.1093

2 Impeller Stainless steel 1.4301

3 Shaft Stainless steel 1.4305

4 Coupling Cast iron EN-GJL-400 0.7040

5 Pump headCast iron EN-GJL-250, bronze

0.60252.1093

Secondary seals EPDM

Rotating seal face Silicon carbide

Stationary seatCarbon (resin-impregnated), silicon carbide

Unbalanced shaft seal

TP Series 100 Version KU according to EN 12756

TP, TPD Series 200

Version NU according to EN 12756

Shaft diameter 12 and 16 mm

Rubber bellows EPDM

Seal facesSilicon carbide/carbon

Silicon carbide/silicon carbide

5 4

3

2

1

Pe

rfo

rma

nc

e r

an

ge

TP, TPD, TPE, TPED, TPE2, TPE2 D, TPE3, TPE3 D

Performance range, 2-pole, PN 6, 10, 16

TM

02

75

50

46

17

11.

52

34

56

81010

1520

3040

5060

8010

010

015

020

030

040

0

Q [m

³/h]

2345681015203040506080[m]

H

112

34

56

78

91010

2030

4050

6070

Q [l

/s]

2030405060708090100

100

200

300

400

500

600

700

800

[kP

a]p

TP

(D),

TP

E(D

)P

N 6

/10/

16, 2

-pol

e, 5

0 H

z

32-8

0

32-5

0

25-9

0

25-5

0

25-8

0

125-

310

125-

360

65-

170

65-2

10

65-2

5050-4

20

50-5

40

50-6

30

40-4

3040

-530

40-6

30

100-

250100-3

1010

0-36

0

100-3

90

65-3

40

65-4

10

65-4

60

65-5

5065-6

60

65-7

20

65-9

30

50-1

60

50-1

90

50-2

40

50-2

9050

-360

50-4

30

50-7

10

50-8

30

50-9

00

40-2

40

40-3

0040-3

60

32-2

00

32-2

50

32-3

20

32-3

80

32-4

60

32-5

80

100-

120

80-1

20

65-1

80

65-1

20

65-6

0

50-1

80

50-1

20

50-6

0

40-2

70

40-2

30

40-1

90

40-1

80

40-1

20 40-6

0

32-2

30

32-1

80

32-1

50

32-1

20 32-60

40-5

0

40-9

0

80-1

40

80-1

8080-2

10

80-2

40

80-2

5080

-33080

-400

80-5

20

80-5

70

80-7

00

100-

16010

0-20

0

100-

240

100-

480

32-9

0

12

Pe

rform

an

ce

ran

ge

TP, TPD, TPE, TPED, TPE2, TPE2 D, TPE3, TPE3 D

Performance range, 2-pole, PN 25

TM

06

65

33

42

17

2030

4050

6070

8010

015

020

030

040

050

0

Q [m

³/h]

30405060708090100

120

140

[m]

H

67

89

101020

3040

5060

7080

9010

010

0Q

[l/s

]

300

400

500

600

700

800

900

1000

1000

[kP

a]p

TP

PN

25,

2-p

ole,

50

Hz

100-

530

100-

650

100-

800

100-

950

100-

1040

100-

1200

100-

1410

Pe

rfo

rma

nc

e r

an

ge

TP, TPD, TPE, TPED, TPE2, TPE2 D, TPE3, TPE3 D

Performance range, 4-pole, PN 6, 10, 16

TM

02

75

51

42

17

23

45

68

1012

1520

3040

5060

8010

015

020

030

040

060

010

0015

0020

00

Q [m

³/h]

12345681010152030405060[m]

H

112

34

56

78

101020

3040

5060

8010

010

020

030

0Q

[l/s

]

101020304050607080100

100

200

300

400

500

600

700

[kP

a]p

TP

(D),

TP

E(D

)P

N 6

/10/

16, 4

-pol

e, 5

0 H

z

350-2

80

350-320

350-

360

350-

420

350-

480

350-

530

350-

650

350-

780

300-

190

300-

220

300-250300-290

300-

390

300-

420

300-

430

300-

500

300-

550

150-

150-

155

150-

110

150-

70

125-

95

125-80

125-

125-

400

125-

340

125-

300

125-

230

125-

190

50-1

40

50-1

2050

-80

40-1

40

40-1

10

200-

160

200-

190

200-

200

200-

240

200-

290

200-

50

200-

70200-

90200-

130

200-

150

150-

450

150-

520

150-

660

100-

70

100-

90

100-

110

200-

660

200-

530

200-

590

150-

260

150-

280

150-

340

150-

390

100-

410

100-

370

100-

330

100-

250

100-

200

100-

170

100-

130

80-3

40

80-2

70

80-2

40

80-1

70 80-1

50

80-1

10

80-9

0

80-7

0

65-1

10

65-1

30

65-1

50

65-1

70

65-2

40

65-9

0

50-1

90

50-2

30

50-9

0

40-1

00

32-1

00

32-1

20

32-8

0

100-

60

100-

30

80-6

0

80-3

0

65-6

0

65-3

0

50-6

0

50-3

0

40-9

040

-60 40

-30

32-6

0

32-4

0

32-3

0

125-

130

125-

160

150-

130

150-

160

150-

220

150-

200

150-

250

200-

410

200-

320

200-

270

200-

470

200-

400

200-

360

200-330

60

170

210

0010

00160 1060

Pe

rform

an

ce

ran

ge

TP, TPD, TPE, TPED, TPE2, TPE2 D, TPE3, TPE3 D

Performance range, 4-pole, PN 25

TM

02

68

69

42

17

2030

4050

6080

100

150

200

300

400

500

600

800

1000

1500

2000

3000

5000

Q [m

³/h]

8101520304050607080[m]

H

67

89

101020

3040

5060

7080

100

100

200

300

400

500

600

800

Q [l

/s]

8090100

100

200

300

400

500

600

700

800

[kP

a]p

TP

PN

25,

4-p

ole,

50

Hz

200-

410

200-

320

200-

660

200-

590

200-

530

200-

470

200-

400

200-360

200-

270

200-

290

200-

240

200-

200

200-

160

150-

660

150-

520

150-

450

150-

390

150-

280

150-

260

150-

250

150-

220

150-

150-

160

150-

130

125-

400

125-

340

125-

300

125-

230

125-

190

125-

150

100-

140

100-

200

100-

250

100-

330

100-

370

100-

410

350-

280

350-320

350-36035

0-420

350-

480

350-

530

350-

650

350-

780

300-

190

300-

220

300-

250

300-

290

300-3

90

300-420

300-

430

300-

500

300-

550

400-

720

400-

760

400-

670

400-

540

400-510

400-

470

200

Pe

rfo

rma

nc

e r

an

ge

TP, TPD, TPE, TPED, TPE2, TPE2 D, TPE3, TPE3 D

Performance range, 6-pole, PN 16

TM

02

87

68

38

14

����

���

����

���

���

���

���

��

����

������������� �

��

��

������

���

��������

����������������

���

���

�����

�����

�!���"��� #�$"�����%

�������

�������

�������

������

���������

��������

��������

��������

��������

��������

V7124417 1117

ECM: 1222592 Th

e n

am

e G

run

dfo

s, t

he

Gru

nd

fos

log

o,

an

d b

e t

hin

k i

nn

ov

ate

are

re

gis

tere

d t

rad

em

ark

s o

wn

ed

by

Gru

nd

fos

Ho

ldin

g A

/S o

r G

run

dfo

s A

/S,

De

nm

ark

. A

ll ri

gh

ts r

ese

rve

d w

orl

dw

ide

Co

pyr

igh

t G

run

dfo

s H

old

ing

A/S

[email protected] Tel. +31-152-610-900www.lenntech.com Fax. [email protected] Tel. +31-152-610-900www.lenntech.com Fax. +31-152-616-289

Lenntech