Tungsten Carbide (TC) Tips for High-Pressure SprayingTungsten Carbide (TC) Tips for High-Pressure Spraying Spray Nozzles Spray Control Spray ... 2000 psi (138 bar) Hollow cone •

Tungsten Carbide (TC) Tips for High-Pressure Spraying

Spray Nozzles

Spray Control

Spray Analysis

Spray Fabrication

2 1.800.95.SPRAY | Intl. 1.630.665.5000 | www.spray.com

Tungsten Carbide Tips Save Water, Chemicals and ElectricityIn high-pressure spraying applications, the high velocity of the liquid through the nozzle causes the orifice to wear very quickly. As the orifice becomes larger, the flow rate will increase. Surprisingly, tens and even hundreds of thousands of dollars can be wasted in excess water and chemicals as a result of nozzle wear. Electricity costs will also rise due to excess pump operation.

Using spray tips constructed of a harder material may provide significantly longer wear life. The Abrasion Resistance Ratio chart below shows that tungsten carbide has a resistance ratio up to 250 times greater than brass.

Approximate Abrasion Resistance Ratios

Spray Nozzle Material Resistance Ratio

Aluminum 1

Brass 1

Polypropylene 1 - 2

Steel 1.5 - 2

Monel® 2 - 3

Stainless Steel 4 - 6

Hastelloy® 4 - 6

Hardened Stainless Steel 10 - 15

Stellite® 10 - 15

Silicon Carbide (Nitride Bonded)

90 - 130

Ceramics 90 - 200

Carbides 180 - 250

Synthetic ruby or sapphire 600 - 2000

Monel® is a registered trademark of Special Metals Corporation.Hastelloy® is a registered trademark of Haynes International, Inc.Stellite® is a registered trademark of Deloro Stellite.

31.800.95.SPRAY | Intl. 1.630.665.5000 | www.spray.com

TC TipS Overview

Model Max. Pressure Spray Pattern Typical Applications Page

Fine Spray TC Tips

2000 psi (138 bar)

Hollow cone

• Humidification

• Coating inside piping

• Evaporative cooling

4

High-Pressure TC Tips

3000 psi (207 bar)

Flat spray• Paint spraying

• Sealant/protective coating spraying5

Heavy Edge TC Tips

4000 psi (276 bar)

Flat spray • Road paint striping 9

Robotic TC Tips

4000 psi (276 bar)

Flat spray• Robotic spraying

• Sealant/coating spraying11

ECRTC Tips4000 psi (276 bar)

Even flat spray

• Viscous solution spraying such as thickened paints and adhesives

• High particulate solution spraying

14

RotoClean® Airless Spray Nozzles

5000 psi (345 bar)

Flat spray• Manual spraying

• High-pressure paint spraying16

High-Pressure 11430 UniJet® Body

3000 psi (207 bar)

Flat spray• Nozzle body for high pressure

UniJet spray tips20

Model HV Orifice2000 psi (138 bar)

Flat spray• Orifice insert produces a fine finish;

for use with high-pressure TC tips20


Fine Spray TC TipsBenefits

• Ideal for humidification, coating inside piping and evaporative cooling

• Very small drop size

• Hydraulic atomization – no compressed air required

Specifications

Maximum pressure: 2000 psi (138 bar)

Spray pattern: Hollow cone

Materials: 303 stainless steel with tungsten carbide orifice

Ordering Information

A B Net Weight

.593" .625" .42 oz

Dimensions & Weights

Capacity Size

Equiv. Orifice

Dia.

Capacity* (gallons per minute) Approx.** Spray Pattern

Diameter (at 1'

distance)

400 psi

750 psi

1000 psi

1500 psi

2000 psi

.60 .016" .032 .043 .050 .061 .072 3"

.80 .0135" .042 .058 .067 .082 .095 3"

.90 .016" .047 .065 .075 .092 .11 3"

1 .020" .053 .072 .083 .10 .12 3-1/2"

1.5 .020" .080 .11 .13 .15 .18 3-1/2"

1.8 .025" .094 .13 .15 .18 .22 4-1/2"

2 .028" .11 .14 .17 .21 .24 4-1/2"

3 .028" .16 .22 .25 .31 .35 6"

4 .042" .21 .29 .33 .41 .47 8"

6 .042" .32 .43 .50 .61 .71 10"

8 .060" .42 .58 .67 .82 .94 12"

9 .060" .47 .65 .75 .92 1.1 14"

10 .064" .53 .72 .83 1.0 1.2 16"

12 .076" .63 .87 1.0 1.2 1.4 18"

14 .076" .74 1.0 1.2 1.4 1.6 14"

15 .081" .79 1.1 1.25 1.5 1.7 16"

16 .086" .84 1.2 1.3 1.6 1.9 18"

18 .076" .95 1.3 1.5 1.8 2.1 16"

20 .081" 1.1 1.4 1.7 2.1 2.4 18"

22 .076" 1.2 1.6 1.8 2.3 2.6 12"

24 .081" 1.3 1.7 2.0 2.5 2.8 13"

26 .086" 1.4 1.9 2.2 2.7 3.1 14"

Fine Spray TC Tips Performance Data

* Tabulated capacities based on water.** Spray pattern diameter is based on liquid with viscosity of 20 seconds, #4 Zahn Cup

spraying at 1600 psi (110 bar). Coverage will vary with viscosities and pressures.

Fine Spray TC Tip

B

A

T N — S S T C 1 0 | | | Tip Material Capacity Type Code Size

TN-SSTC Spray Tip

Based on largest/heaviest version of each type.


High-Pressure TC TipsBenefits

• Ideal for paint spraying and the application of sealants and protective coatings in automotive manufacturing

• Erosion-resistant tungsten carbide orifice insert provides longer wear life than standard stainless steel tips

• Excellent corrosion resistance

• High-impact flat spray pattern with tapered edges provides even coverage when sprays overlap

• Tip orifice insert is recessed in a solid stainless steel tip body to protect against damage

Specifications


Spray pattern: Flat spray

Materials: Stainless steel with tungsten carbide orifice insert

High-Pressure 11430 UniJet® Body with

High-Pressure TC Tip

Spray Angle

at 40 psi

Spray Tip Number

Equiv. Orifice

Dia.

Capacity* (gallons per minute)

Approx.** Spray

Pattern Width (at 1’

distance)

500 psi

1000 psi

1500 psi

2000 psi

3000 psi

110°

1100017-TC .011" .06 .09 .10 .12 .15 15-1/2"

1100025-TC .013" .09 .12 .15 .18 .22 16-1/2"

1100033-TC .015" .12 .16 .20 .23 .29 17"

1100039-TC .016" .14 .20 .24 .28 .34 18"

1100050-TC .018" .18 .25 .30 .36 .44 19"

1100067-TC .021" .24 .33 .41 .47 .59 21"

1100080-TC .023" .28 .40 .49 .57 .69 22"

11001-TC .026" .35 .50 .61 .72 .86 23"

110015-TC .031" .53 .75 .91 1.1 1.3 25"

11002-TC .036" .71 1.0 1.2 1.4 1.7 26"

11003-TC .043" 1.1 1.5 1.8 2.1 2.7 27"

Spray Angle

at 40 psi

Spray Tip Number

Equiv. Orifice

Dia.


Approx.** Spray


distance)

500 psi

1000 psi

1500 psi

2000 psi

3000 psi

110°

11004-TC .052" 1.4 2.0 2.5 2.8 3.4 28"

11005-TC .057" 1.8 2.5 3.1 3.5 4.4 28"

110053-TC .058" 1.9 2.7 3.2 3.7 4.7 28"

11006-TC .062" 2.1 3.0 3.7 4.2 5.1 28"

11007-TC .067" 2.5 3.5 4.3 5.0 6.1 28"

11008-TC .072" 2.8 4.0 4.9 5.7 6.9 28"

11009-TC .076" 3.2 4.5 5.5 6.4 7.8 28"

11010-TC .078" 3.5 5.0 6.1 7.1 8.6 28"

11011-TC .083" 3.9 5.5 6.7 7.8 9.6 28"

11012-TC .089" 4.3 6.0 7.4 8.5 10.5 28"

95° 950017-TC .011" .06 .08 .10 .12 .15 13"

High-Pressure TC Tips Performance Data

* Tabulated capacities based on water. ** Spray pattern width is based on liquid with viscosity of 20 seconds, #4 Zahn Cup spraying at 1600 psi (110 bar). Coverage will vary with viscosities and pressures.

High-Pressure TC Tip


Spray Angle

at 40 psi

Spray Tip Number

Equiv. Orifice

Dia.


Approx.** Spray


distance)

500 psi

1000 psi

1500 psi

2000 psi

3000 psi

95°

950025-TC .013" .09 .12 .15 .18 .22 14"

950033-TC .015" .12 .16 .20 .23 .29 15"

950039-TC .016" .14 .20 .24 .28 .34 16"

950044-TC .017" .16 .22 .27 .31 .39 16"

950050-TC .018" .18 .25 .30 .36 .44 17"

950067-TC .021" .24 .33 .41 .47 .59 19"

950080-TC .023" .28 .40 .49 .57 .69 19"

9501-TC .026" .35 .50 .61 .72 .86 21"

95015-TC .031" .53 .75 .91 1.1 1.3 21"

9502-TC .036" .71 1.0 1.2 1.4 1.7 22"

9503-TC .043" 1.1 1.5 1.8 2.1 2.7 22"

9504-TC .052" 1.4 2.0 2.5 2.8 3.4 23"

9505-TC .057" 1.8 2.5 3.1 3.5 4.4 23"

9506-TC .062" 2.1 3.0 3.7 4.2 5.1 23"

9507-TC .067" 2.5 3.5 4.3 5.0 6.1 23"

9508-TC .072" 2.8 4.0 4.9 5.7 6.9 23"

9509-TC .076" 3.2 4.5 5.5 6.4 7.8 23"

9510-TC .078" 3.5 5.0 6.1 7.1 8.6 23"

9511-TC .085" 3.9 5.5 6.7 7.8 9.6 23"

9512-TC .089" 4.3 6.0 7.4 8.5 10.5 23"

9513-TC .092" 4.6 6.5 8.0 9.2 11.3 23"

9514-TC .095" 4.9 7.0 8.6 9.9 12.0 23"

9515-TC .099" 5.3 7.5 9.2 10.6 13.0 23"

9516-TC .100" 5.7 8.0 9.8 11.3 14.0 23"

9518-TC .104" 6.4 9.0 11.0 12.7 15.7 23"

9520-TC .109" 7.1 10.0 12.2 14.1 17.4 23"

80°

800011-TC .009" .04 .06 .07 .08 .10 10-1/2"

800017-TC .011" .06 .08 .10 .12 .15 11-1/2"

800025-TC .013" .09 .12 .15 .18 .22 12-1/2"

800033-TC .015" .12 .16 .20 .23 .29 13"

800039-TC .016" .14 .20 .24 .28 .34 14"

800050-TC .018" .18 .25 .30 .36 .44 15"

800067-TC .021" .24 .33 .41 .47 .59 17"

800080-TC .023" .28 .40 .49 .57 .69 17"

8001-TC .026" .35 .50 .61 .72 .86 19"

80015-TC .031" .53 .75 .91 1.1 1.3 19"

8002-TC .036" .71 1.0 1.2 1.4 1.7 19"

8003-TC .043" 1.1 1.5 1.8 2.1 2.7 19"

8004-TC .052" 1.4 2.0 2.5 2.8 3.4 19"

8005-TC .057" 1.8 2.5 3.1 3.5 4.4 19"

8006-TC .062" 2.1 3.0 3.7 4.2 5.1 19"

8007-TC .067" 2.5 3.5 4.3 5.0 6.1 19"

Spray Angle

at 40 psi

Spray Tip Number

Equiv. Orifice

Dia.


Approx.** Spray


distance)

500 psi

1000 psi

1500 psi

2000 psi

3000 psi

80°

8008-TC .072" 2.8 4.0 4.9 5.7 6.9 19"

8009-TC .076" 3.2 4.5 5.5 6.4 7.8 19"

8010-TC .078" 3.5 5.0 6.1 7.1 8.6 19"

8011-TC .085" 3.9 5.5 6.7 7.8 9.6 19"

8012-TC .089" 4.3 6.0 7.4 8.5 10.5 19"

8013-TC .093" 4.6 6.5 8.0 9.2 11.3 19"

8014-TC .096" 4.9 7.0 8.6 9.9 12.0 19"

8015-TC .099" 5.3 7.5 9.2 10.6 13.0 19"

73°

730023-TC .012" .08 .11 .14 .16 .20 11-1/2"

730039-TC .016" .14 .20 .24 .28 .34 13"

730044-TC .017" .17 .22 .27 .31 .42 13"

730050-TC .018" .18 .25 .31 .35 .44 13"

730154-TC .031" .54 .77 .94 1.1 1.3 13"

65°

650008-TC .007" .03 .04 .05 .06 .07 8-1/2"

650011-TC .009" .04 .06 .07 .08 .10 9-1/4"

650017-TC .011" .06 .08 .10 .12 .15 10"

650025-TC .013" .09 .12 .15 .18 .22 10-1/2"

650033-TC .015" .12 .16 .20 .23 .29 11"

650039-TC .016" .14 .20 .24 .28 .34 12"

650044-TC .017" .16 .22 .27 .31 .39 12-1/2"

650050-TC .018" .18 .25 .30 .36 .44 13"

650055-TC .019" .19 .28 .34 .39 .47 13"

650067-TC .021" .24 .33 .41 .47 .59 15"

650080-TC .023" .28 .40 .49 .57 .69 15"

6501-TC .026" .35 .50 .61 .72 .86 16"

65015-TC .031" .53 .75 .91 1.1 1.3 16"

6502-TC .036" .71 1.0 1.2 1.4 1.7 16"

6503-TC .043" 1.1 1.5 1.8 2.1 2.7 16"

6504-TC .052" 1.4 2.0 2.5 2.8 3.4 16"

6505-TC .057" 1.8 2.5 3.1 3.5 4.4 16"

6506-TC .062" 2.1 3.0 3.7 4.2 5.1 16"

6507-TC .067" 2.5 3.5 4.3 5.0 6.1 16"

6508-TC .072" 2.8 4.0 4.9 5.7 6.9 16"

6509-TC .076" 3.2 4.5 5.5 6.4 7.8 16"

6510-TC .078" 3.5 5.0 6.1 7.1 8.6 16"

6511-TC .085" 3.9 5.5 6.7 7.8 9.6 16"

6512-TC .089" 4.3 6.0 7.4 8.5 10.5 16"

6513-TC .093" 4.6 6.5 8.0 9.2 11.3 16"

6514-TC .096" 4.9 7.0 8.6 9.9 12.0 16"

6515-TC .099" 5.3 7.5 9.2 10.6 13.0 16"

6517-TC .102" 6.0 8.5 10.4 12.0 14.7 16"

6520-TC .109" 7.1 10.0 12.2 14.1 17.4 16"

* Tabulated capacities based on water.** Spray pattern diameter is based on liquid with viscosity of 20 seconds, #4 Zahn Cup spraying at 1600 psi (110 bar). Coverage will vary with viscosities and pressures.



Spray Angle

at 40 psi

Spray Tip Number

Equiv. Orifice

Dia.


Approx.** Spray


distance)

500 psi

1000 psi

1500 psi

2000 psi

3000 psi

50°

500004-TC .005" .01 .02 .02 .03 .03 6-1/2"

500006-TC .006" .02 .03 .04 .04 .05 7"

500008-TC .007" .03 .04 .05 .06 .07 7-3/4"

500011-TC .009" .04 .06 .07 .08 .10 8"

500017-TC .011" .06 .08 .10 .12 .15 8-1/2"

500025-TC .013" .09 .12 .15 .18 .22 9"

500033-TC .015" .12 .16 .20 .23 .29 10"

500039-TC .016" .14 .20 .24 .28 .34 10-1/2"

500044-TC .017" .16 .22 .27 .31 .39 10-1/2"

500050-TC .018" .18 .25 .30 .36 .44 11"

500055-TC .019" .19 .28 .34 .39 .47 11"

500067-TC .021" .24 .33 .41 .47 .59 12"

500080-TC .023" .28 .40 .49 .57 .69 13"

5001-TC .026" .35 .50 .61 .72 .86 14"

50015-TC .031" .53 .75 .91 1.1 1.3 14"

5002-TC .036" .71 1.0 1.2 1.4 1.7 14"

5003-TC .043" 1.1 1.5 1.8 2.1 2.7 14"

5004-TC .052" 1.4 2.0 2.5 2.8 3.4 14"

5005-TC .057" 1.8 2.5 3.1 3.5 4.4 14"

5006-TC .062" 2.1 3.0 3.7 4.2 5.1 14"

5007-TC .067" 2.5 3.5 4.3 5.0 6.1 14"

5008-TC .072" 2.8 4.0 4.9 5.7 6.9 14"

5010-TC .078" 3.5 5.0 6.1 7.1 8.6 14"

5015-TC .099" 5.3 7.5 9.2 10.6 13.0 14"

40°

400004-TC .005" .01 .02 .03 .03 .03 6-1/2"

400006-TC .006" .02 .03 .04 .04 .05 6-1/2"

400008-TC .007" .03 .04 .05 .06 .07 6-1/2"

400011-TC .009" .04 .06 .07 .08 .10 7"

400017-TC .011" .06 .08 .10 .12 .15 7-1/2"

400025-TC .013" .09 .12 .15 .18 .22 8"

400033-TC .015" .12 .16 .20 .23 .29 8-1/2"

400039-TC .016" .14 .20 .24 .28 .34 9"

400044-TC .017" .16 .22 .27 .31 .39 9-1/2"

400050-TC .018" .18 .25 .30 .36 .44 10"

400055-TC .019" .19 .28 .34 .39 .47 10"

400067-TC .021" .24 .33 .41 .47 .59 11"

400080-TC .023" .28 .40 .49 .57 .69 11"

4001-TC .026" .35 .50 .61 .72 .86 12"

40013-TC .029" .46 .65 .80 .92 1.1 12"

40015-TC .031" .53 .75 .91 1.1 1.3 12"

4002-TC .036" .71 1.0 1.2 1.4 1.7 12"

4003-TC .043" 1.1 1.5 1.8 2.1 2.7 12"

Spray Angle

at 40 psi

Spray Tip Number

Equiv. Orifice

Dia.


Approx.** Spray


distance)

500 psi

1000 psi

1500 psi

2000 psi

3000 psi

40°

4004-TC .052" 1.4 2.0 2.5 2.8 3.4 12"

4005-TC .057" 1.8 2.5 3.1 3.5 4.4 12"

4006-TC .062" 2.1 3.0 3.7 4.2 5.1 12"

4007-TC .067" 2.5 3.5 4.3 5.0 6.1 12"

4008-TC .072" 2.8 4.0 4.9 5.7 6.9 12"

4009-TC .076" 3.2 4.5 5.5 6.4 7.8 12"

4010-TC .078" 3.5 5.0 6.1 7.1 8.6 12"

4011-TC .083" 3.9 5.5 6.7 7.8 9.6 12"

4015-TC .099" 5.3 7.5 9.2 10.6 13.0 12"

25°

250004-TC .005" .01 .02 .03 .03 .03 5"

250006-TC .006" .02 .03 .04 .04 .05 5"

250008-TC .007" .03 .04 .05 .06 .07 5-1/2"

250011-TC .009" .04 .06 .07 .08 .10 5-1/2"

250017-TC .011" .06 .08 .10 .12 .15 6"

250025-TC .013" .09 .12 .15 .18 .22 6"

250033-TC .015" .12 .16 .20 .23 .29 7"

250039-TC .016" .14 .20 .24 .28 .34 7"

250050-TC .018" .18 .25 .30 .36 .44 7"

250055-TC .019" .19 .28 .34 .39 .47 7"

250067-TC .021" .24 .33 .41 .47 .59 8"

250080-TC .023" .28 .40 .49 .57 .69 8-1/2"

2501-TC .026" .35 .50 .61 .72 .86 9"

25015-TC .031" .53 .75 .91 1.1 1.3 9"

2502-TC .036" .71 1.0 1.2 1.4 1.7 9"

2503-TC .043" 1.1 1.5 1.8 2.1 2.7 9"

2504-TC .052" 1.4 2.0 2.5 2.8 3.4 9"

2505-TC .057" 1.8 2.5 3.1 3.5 4.4 9"

2506-TC .062" 2.1 3.0 3.7 4.2 5.1 9"

2508-TC .072" 2.8 4.0 4.9 5.7 6.9 9"

2510-TC .078" 3.5 5.0 6.1 7.1 8.6 9"

15°

150004-TC .005" .01 .02 .03 .03 .03 4"

150006-TC .006" .02 .03 .04 .04 .05 4"

150008-TC .007" .03 .04 .05 .06 .07 4-1/2"

150011-TC .009" .04 .06 .07 .08 .10 4-1/2"

150017-TC .011" .06 .08 .10 .12 .15 5"

150025-TC .013" .09 .12 .15 .18 .22 5"

150033-TC .015" .12 .16 .20 .23 .29 5-1/2"

150039-TC .016" .14 .20 .24 .28 .34 6"

150044-TC .017" .16 .22 .27 .31 .39 6"

150050-TC .018" .18 .25 .30 .36 .44 6"

150067-TC .021" .24 .33 .41 .47 .59 6-1/2"

150080-TC .023" .28 .40 .49 .57 .69 7"




Spray Angle

at 40 psi

Spray Tip Number

Equiv. Orifice

Dia.


Approx.** Spray


distance)

500 psi

1000 psi

1500 psi

2000 psi

3000 psi

15°

1501-TC .026" .35 .50 .61 .72 .86 7"

15015-TC .031" .53 .75 .91 1.1 1.3 7"

1502-TC .036" .71 1.0 1.2 1.4 1.7 7"

1503-TC .043" 1.1 1.5 1.8 2.1 2.7 7"

1504-TC .052" 1.4 2.0 2.5 2.8 3.4 7"

1505-TC .057" 1.8 2.5 3.1 3.5 4.4 7"

1506-TC .062" 2.1 3.0 3.7 4.2 5.1 7"

1507-TC .067" 2.5 3.5 4.3 4.9 6.1 7"

1508-TC .072" 2.8 4.0 4.9 5.7 6.9 7"

1510-TC .078" 3.5 5.0 6.1 7.1 8.6 7"

1515-TC .099" 5.3 7.5 9.2 10.6 13.0 7"

10°

100004-TC .005" .01 .02 .03 .03 .03 3"

100006-TC .006" .02 .03 .04 .04 .05 3"

100008-TC .007" .03 .04 .05 .06 .07 3-1/2"

100011-TC .009" .04 .06 .07 .08 .10 3-1/2"

100017-TC .011" .06 .08 .10 .12 .15 4"

100025-TC .013" .09 .12 .15 .18 .22 4"

100033-TC .015" .12 .16 .20 .23 .29 4-1/2"

100039-TC .016" .14 .20 .24 .28 .34 5"



Spray Angle

at 40 psi

Spray Tip Number

Equiv. Orifice

Dia.


Approx.** Spray


distance)

500 psi

1000 psi

1500 psi

2000 psi

3000 psi

10°

100050-TC .018" .18 .25 .30 .36 .44 5"

100067-TC .021" .24 .33 .41 .47 .59 5-1/2"

100080-TC .023" .28 .40 .49 .57 .69 5-1/2"

1001-TC .026" .35 .50 .61 .72 .86 6"

10015-TC .031" .53 .75 .91 1.1 1.3 6"

1002-TC .036" .71 1.0 1.2 1.4 1.7 6"

5°

050004-TC .005" .01 .02 .03 .03 .03 2-1/2"

050008-TC .007" .03 .04 .05 .06 .07 2-1/2"

050011-TC .009" .04 .06 .07 .08 .10 2-1/2"

050017-TC .011" .06 .08 .10 .12 .15 3"

050025-TC .013" .09 .12 .15 .18 .22 3"

050033-TC .015" .12 .16 .20 .23 .29 3-1/2"

050039-TC .016" .14 .20 .24 .28 .34 4"

050050-TC .018" .18 .25 .30 .36 .44 4"

050067-TC .021" .24 .33 .41 .47 .59 4"

0501-TC .026" .35 .50 .61 .72 .86 4"

05015-TC .031" .53 .75 .91 1.1 1.3 4"

0502-TC .036" .71 1.0 1.2 1.4 1.7 4"

0503-TC .043" 1.1 1.5 1.8 2.1 2.7 4"



T p 1 5 0 4 – T C | | | | Tip Spray Capacity Material Code Angle Size Code

High-pressure TC Spray Tip


A

B

A B Net Weight

.375" .59" .32 oz


Heavy Edge TC TipsBenefits

• Ideal for road paint striping

• Heavy edge distribution for defined edge pattern


• Excellent corrosion resistance


Specifications



Materials: Stainless steel with tungsten carbide orifice insert

Heavy Edge TC Tips Performance Data

Heavy Edge TC Tip

Nozzle Type A B Net

Weight

Small Capacity (up to -025) .375" .593" .32 oz

Large Capacity (-03 and larger) .50" .593" .32 oz


A

B


4 0 0 5 H e – T C | | | | Spray Capacity Tip Material Angle Size Code Code

Heavy edge TC Spray Tip

Spray Angle

at 40 psi

Spray Tip Number

Equiv. Orifice

Dia.


500 psi

1000 psi

1500 psi

2000 psi

3000 psi

4000 psi

65°

650033HE-TC .015" .12 .16 .20 .23 .29 .34

6507HE-TC .067" 2.5 3.5 4.3 4.9 6.1 7.1

6508HE-TC .072" 2.8 4.0 4.9 5.7 6.9 7.9

50°

500050HE-TC .018" .18 .25 .30 .36 .44 .51

5001HE-TC .026" .35 .50 .61 .72 .86 .99

50015HE-TC .031" .53 .75 .91 1.1 1.3 1.5

5002HE-TC .036" .71 1.0 1.2 1.4 1.7 2.0

50025HE-TC .040" .88 1.3 1.5 1.8 2.2 2.5

5004HE-TC .052" 1.4 2.0 2.5 2.8 3.4 4.0


*Tabulation is based on water spraying at temperature at 70°F (21°C).


Spray Angle

at 40 psi

Spray Tip Number

Equiv. Orifice

Dia.


500 psi

1000 psi

1500 psi

2000 psi

3000 psi

4000 psi

50°

5005HE-TC .057" 1.8 2.5 3.1 3.5 4.4 5.1

5006HE-TC .062" 2.1 3.0 3.7 4.2 5.1 6.0

5007HE-TC .067" 2.5 3.5 4.3 4.9 6.1 7.1

5008HE-TC .072" 2.8 4.0 4.9 5.7 6.9 7.9

5009HE-TC .076" 3.2 4.5 5.5 6.4 7.8 9.1

40°

400033HE-TC .015" .12 .16 .20 .23 .29 .34

4001HE-TC .026" .35 .50 .61 .72 .86 1.5

4002HE-TC .036" .71 1.0 1.2 1.4 1.7 2.0

4003HE-TC .043" 1.1 1.5 1.8 2.1 2.7 3.1

4005HE-TC .057" 1.8 2.5 3.1 3.5 4.4 5.1

4006HE-TC .062" 2.1 3.0 3.7 4.2 5.1 6.0

4007HE-TC .067" 2.5 3.5 4.3 4.9 6.1 7.1

4008HE-TC .072" 2.8 4.0 4.9 5.7 6.9 7.9

4009HE-TC .076" 3.2 4.5 5.5 6.4 7.8 9.1

35° 3506HE-TC .062" 2.1 3.0 3.7 4.2 5.1 6.0

30°

3006HE-TC .062" 2.1 3.0 3.7 4.2 5.1 6.0

3007HE-TC .067" 2.5 3.5 4.3 4.9 6.1 7.1

3008HE-TC .072" 2.8 4.0 4.9 5.7 6.9 7.9

3009HE-TC .076" 3.2 4.5 5.5 6.4 7.8 9.1

25° 250025HE-TC .013" .09 .12 .15 .18 .29 .34

Spray Angle

at 40 psi

Spray Tip Number

Equiv. Orifice

Dia.


500 psi

1000 psi

1500 psi

2000 psi

3000 psi

4000 psi

25°

2501HE-TC .026" .35 .50 .61 .72 .86 1.5

25015HE-TC .031" .53 .75 .91 1.1 1.3 1.5

2502HE-TC .036" .71 1.0 1.2 1.4 1.7 2.0

2503HE-TC .043" 1.1 1.5 1.8 2.1 2.7 3.1

2504HE-TC .052" 1.4 2.0 2.5 2.8 3.4 4.0

2505HE-TC .057" 1.8 2.5 3.1 3.5 4.4 5.1

2506HE-TC .062" 2.1 3.0 3.7 4.2 5.1 6.0

2508HE-TC .072" 2.8 4.0 4.9 5.7 6.9 7.9

2510HE-TC .078" 3.5 5.0 6.1 7.1 9.0 9.9

20° 2003HE-TC .043" 1.1 1.5 1.8 2.1 2.7 3.1

15°

150080HE-TC .023" .28 .40 .49 .57 .69 .79

1501HE-TC .026" .35 .50 .61 .72 .86 1.5

15015HE-TC .031" .53 .75 .91 1.1 1.3 1.5

1502HE-TC .036" .71 1.0 1.2 1.4 1.7 2.0

1503HE-TC .043" 1.1 1.5 1.8 2.1 2.7 3.1

1504HE-TC .052" 1.4 2.0 2.5 2.8 3.4 4.0

1505HE-TC .057" 1.8 2.5 3.1 3.5 4.4 5.1

1506HE-TC .062" 2.1 3.0 3.7 4.2 5.1 6.0

1508HE-TC .072" 2.8 4.0 4.9 5.7 6.9 7.9

10° 10025HE-TC .040" .88 1.3 1.5 1.8 2.5 2.5

Heavy Edge TC Tips Performance Data

* Tabulation is based on water spraying at temperature at 70°F (21°C).


Robotic TC TipsBenefits

• Ideal for use with robotic equipment in precise, repetitive paint spraying applications and operations where overspray is undesirable

• Tips have flats to ensure accurate spray pattern alignment every time



• Tighter coverage tolerances than high-pressure TC tips

• Patented flow channel design minimizes heavy spray pattern edges

• CDROBTC tips feature a shorter tip holder than ROBTC tips and are designed for use in applications where the spray solution tends to dry quickly. The tip design helps the solution slide away from the orifice and prevents clogging caused by caking and build-up

Specifications


Spray pattern: Flat spray or solid stream

Materials: Stainless steel body with tungsten carbide orifice


Nozzle Type A B Locating Flats

Net Weight

TP-ROBTC

.375" .59" 0.5" .32 oz

TP-CDROBTC

.313" .59" 0.5" .32 oz


ROBTC Tip

CDROBTC Tip

A

B

A

B

T p 4 0 0 1 — r O B T C | | | | Tip Spray Capacity Tip Code Angle Size Type

rOBTC Spray Tip

T p 6 5 0 1 — C D r O B T C | | | | Tip Spray Capacity Tip Code Angle Size Type

CDrOBTC Spray TipBased on largest/heaviest version of each type.


* For solid stream tips, the actual orifice diameter is listed.** Spray pattern width is based on liquid with viscosity of 20 seconds, #4 Zahn Cup spraying at 1600 psi (110 bar). Tabulation is based on spraying water at temperature at 70°F (21°C).

Robotic TC Tips Performance Data

Spray Angle

at 40 psi

Spray Tip Number

Equiv. Orifice Dia. *

Capacity (gallons per minute)Spray Pattern Width

(at 1' Distance)**500 psi

1000 psi

1500 psi

2000 psi

2500 psi

3000 psi

3500 psi

4000 psi

110˚

TP1100067-CDROBTC .021" .24 .33 .41 .47 .53 .58 .63 .67 21" to 22"

TP1100080-CDROBTC .023" .28 .40 .49 .57 .63 .69 .75 .80 21-3/4" to 22-3/4"

TP11001-CDROBTC .026" .35 .50 .61 .72 .79 .87 .94 1.0 23-1/2" to 24-1/2"

TP110015-CDROBTC .031" .53 .75 .91 1.1 1.2 1.3 1.4 1.5 25" to 26"

TP11002-CDROBTC .036" .71 1.0 1.2 1.4 1.6 1.7 1.9 2.0 26" to 27"

95˚TP950080-CDROBTC .023" .28 .40 .49 .57 .63 .69 .75 .80 19-1/2" to 20-1/2"

TP9502-CDROBTC .036" .71 1.0 1.2 1.4 1.6 1.7 1.9 2.0 21-1/2" to 22-1/2"

80˚

TP800044-CDROBTC .017" .16 .22 .27 .31 .35 .38 .41 .44 14-1/2" to 15-1/2"

TP800050-CDROBTC .018" .18 .25 .30 .36 .40 .43 .47 .50 15" to 16"

TP800055-CDROBTC .019" .19 .28 .34 .39 .43 .48 .51 .55 14-1/2" to 15-1/2"

TP800067-CDROBTC .021" .24 .33 .41 .47 .53 .58 .63 .67 17" to 18"

TP800080-CDROBTC .023" .28 .40 .49 .57 .63 .69 .75 .80 17-1/4" to 18-1/4"

TP8001-CDROBTC .026" .35 .50 .61 .72 .79 .87 .94 1.0 18-3/4" to 19-3/4"

TP80015-CDROBTC .031" .53 .75 .91 1.1 1.2 1.3 1.4 1.5 18-1/2" to 19-1/2"

TP8002-CDROBTC .036" .71 1.0 1.2 1.4 1.6 1.7 1.9 2.0 18-1/2" to 19-1/2"

TP8003-CDROBTC .043" 1.1 1.5 1.8 2.1 2.4 2.6 2.8 3.0 18-1/2" to 19-1/2"

TP8004-CDROBTC .052" 1.4 2.0 2.5 2.8 3.2 3.5 3.7 4.0 18-1/2" to 19-1/2"

TP8005-CDROBTC .057" .18 2.5 3.1 3.5 4.0 4.3 4.7 5.0 18-1/2" to 19-1/2"

65˚

TP650039-CDROBTC .016" .14 .20 .24 .28 .31 .34 .36 .39 11-1/2" to 12-1/2"

TP650044-CDROBTC .017" .16 .22 .27 .31 .35 .38 .41 .44 12-1/2" to 13-1/2"

TP650050-CDROBTC .018" .18 .25 .30 .36 .40 .43 .47 .50 12-1/2" to 13-1/2"

TP650055-CDROBTC .019" .19 .28 .34 .39 .43 .48 .51 .55 12-1/2" to 13-1/2"

TP650067-CDROBTC .021" .24 .33 .41 .47 .53 .58 .63 .67 14-1/2" to 15-1/2"

TP650080-CDROBTC .023" .28 .40 .49 .57 .63 .69 .75 .80 14-1/2" to 15-1/2"

TP6501-CDROBTC .026" .35 .50 .61 .72 .79 .87 .94 1.0 16-1/4" to 17-1/4"

TP65015-CDROBTC .031" .53 .75 .91 1.1 1.2 1.3 1.4 1.5 15-1/2" to 16-1/2"

TP6502-CDROBTC .036" .71 1.0 1.2 1.4 1.6 1.7 1.9 2.0 14-3/4" to 15-3/4"

TP6503-CDROBTC .043" 1.1 1.5 1.8 2.1 2.4 2.6 2.8 3.0 15-1/2" to 16-1/2"

50˚

TP500044-CDROBTC .017" .16 .22 .27 .31 .35 .38 .41 .44 10-1/2" to 11-1/2"

TP500050-CDROBTC .018" .18 .25 .30 .36 .40 .43 .47 .50 10-1/2" to 11-1/2"

TP500055-CDROBTC .019" .19 .28 .34 .39 .43 .48 .51 .55 10-1/2" to 11-1/2"

TP500067-CDROBTC .021" .24 .33 .41 .47 .53 .58 .63 .67 12-1/2" to 13-1/2"

TP500080-CDROBTC .023" .28 .40 .49 .57 .63 .69 .75 .80 12-1/2" to 13-1/2"

TP5001-CDROBTC .026" .35 .50 .61 .72 .79 .87 .94 1.0 13-1/2" to 14-1/2"

TP50015-CDROBTC .031" .53 .75 .91 1.1 1.2 1.3 1.4 1.5 13-1/2" to 14-1/2"

TP5002-CDROBTC .036" .71 1.0 1.2 1.4 1.6 1.7 1.9 2.0 13-1/2" to 14-1/2"

TP5003-CDROBTC .043" 1.1 1.5 1.8 2.1 2.4 2.6 2.8 3.0 13-1/2" to 14-1/2"

TP5010-CDROBTC .078" 3.5 5.0 6.1 7.1 7.9 8.7 9.4 10.0 13-1/2" to 14-1/2"


* For solid stream tips, the actual orifice diameter is listed.** Spray pattern width is based on liquid with viscosity of 20 seconds, #4 Zahn Cup spraying at 1600 psi (110 bar). Tabulation is based on spraying water at temperature at 70°F (21°C).

Robotic TC Tips Performance Data

Spray Angle

at 40 psi

Spray Tip Number

Equiv. Orifice Dia. *

Capacity (gallons per minute)Spray Pattern Width

(at 1' Distance)**500 psi

1000 psi

1500 psi

2000 psi

2500 psi

3000 psi

3500 psi

4000 psi

40˚

TP400011-CDROBTC .009" .039 .055 .067 .078 .087 .095 .10 .11 6-1/2" to 7-1/2"

TP400017-CDROBTC .011" .06 .08 .10 .12 .13 .15 .16 .17 6-1/2" to 7-1/2"

TP400025-CDROBTC .013" .09 .12 .15 .18 .20 .22 .23 .25 7" to 8"

TP400044-CDROBTC .017" .16 .22 .27 .31 .35 .38 .41 .44 8-1/2" to 9-1/2"

TP400050-CDROBTC .018" .18 .25 .30 .36 .40 .43 .47 .50 8-1/2" to 9-1/2"

TP400055-CDROBTC .019" .19 .28 .34 .39 .43 .48 .51 .55 8-1/2" to 9-1/2"

TP400067-CDROBTC .021" .24 .33 .41 .47 .53 .58 .63 .67 10-1/2" to 11-1/2"

TP400080-CDROBTC .023" .28 .40 .49 .57 .63 .69 .75 .80 10-1/2" to 11-1/2"

TP4001-CDROBTC .026" .35 .50 .61 .72 .79 .87 .94 1.0 11-1/2" to 12-1/2"

TP40015-CDROBTC .031" .53 .75 .91 1.1 1.2 1.3 1.4 1.5 11-1/2" to 12-1/2"

TP4002-CDROBTC .036" .71 1.0 1.2 1.4 1.6 1.7 1.9 2.0 11-1/2" to 12-1/2"

25˚

TP250017-CDROBTC .011" .06 .08 .10 .12 .13 .15 .16 .17 5-1/2" to 6-1/2"

TP250039-CDROBTC .016" .14 .20 .24 .28 .31 .34 .36 .39 6-1/2" to 7-1/2"

TP250050-CDROBTC .018" .18 .25 .30 .36 .40 .43 .47 .50 7-1/2" to 8-1/2"

TP250055-CDROBTC .019" .19 .28 .34 .39 .43 .48 .51 .55 7-1/2" to 8-1/2"

TP250067-CDROBTC .021" .24 .33 .41 .47 .53 .58 .63 .67 8-1/2" to 9-1/2"

TP250080-CDROBTC .023" .28 .40 .49 .57 .63 .69 .75 .80 8-1/4" to 9-1/4"

TP2501-CDROBTC .026" .35 .50 .61 .72 .79 .87 .94 1.0 8-1/2" to 9-1/2"

TP25015-CDROBTC .031" .53 .75 .91 1.1 1.2 1.3 1.4 1.5 9-1/4" to 10-1/4"

TP2502-CDROBTC .036" .71 1.0 1.2 1.4 1.6 1.7 1.9 2.0 8-1/2" to 9-1/2"

5˚

TP050011-CDROBTC .009" .039 .055 .067 .078 .087 .095 .10 .11 2" to 3"

TP050039-CDROBTC .016" .14 .20 .24 .28 .31 .34 .36 .39 4" to 5"

TP050050-CDROBTC .018" .18 .25 .30 .35 .40 .43 .47 .50 4" to 5"

TP050067-CDROBTC .021" .24 .34 .41 .47 .53 .58 .63 .67 4" to 5"

TP0501-CDROBTC .026" .35 .50 .61 .71 .79 .87 .94 1.0 5-1/4" to 6-1/4"

TP05015-CDROBTC .031" .53 .75 .92 1.1 1.2 1.3 1.4 1.5 5-1/2" to 6-1/2"

TP0502-CDROBTC .036" .71 1.0 1.2 1.4 1.6 1.7 1.9 2.0 5-3/4" to 6-3/4"

0˚

TP00009-CDROBTC .026" .30 .43 .52 .60 .67 .74 .80 .85 —

TP0001-CDROBTC .028" .42 .60 .73 .85 .95 1.0 1.1 1.2 —

TP00015-CDROBTC .034" .62 .85 1.0 1.2 1.3 1.5 1.6 1.7 —

TP0002-CDROBTC .039" .81 1.2 1.4 1.6 1.8 2.0 2.2 2.3 —

TP0003-CDROBTC .043" .99 1.4 1.8 2.0 2.2 2.4 2.6 2.8 —

TP0004-CDROBTC .052" 1.5 2.2 2.6 3.0 3.4 3.7 4.0 4.3 —

TP0005-CDROBTC .057" 1.7 2.4 2.9 3.4 3.8 4.2 4.5 4.8 —

TP0006-CDROBTC .063" 2.1 3.0 3.7 4.2 4.7 5.2 5.6 6.0 —


ECRTC TipsBenefits

• Ideal for spraying viscous solutions such as thick paints, epoxies, adhesives and other solutions prone to clogging

• Even flat spray pattern minimizes overspray



• CDECRTC tips feature a shorter tip holder than ECRTC tips and are designed for use in applications where the spray solution tends to dry quickly. The tip design helps the solution slide away from the orifice and prevents clogging caused by caking and build-up

Specifications


Spray pattern: Even flat spray

Materials: Stainless steel body with tungsten carbide orifice


Nozzle Type A B Net Weight

TP-ECRTC .375" .59" .32 oz

TP-CDECRTC .313" .59" .32 oz


ECRTC Tip

CDECRTC Tip

A

B

A

B

T p 5 0 0 0 5 0 — e C r T C | | | | Tip Spray Capacity Tip Code Angle Size Type

eCrTC Spray Tip

T p 5 0 0 0 5 0 — C D e C r T C | | | | Tip Spray Capacity Tip Code Angle Size Type

CDeCrTC Spray TipBased on largest/heaviest version of each type.


ECRTC Tips Performance Data

* Spray pattern width is based on liquid with viscosity of 20 seconds, #4 Zahn Cup spraying at 1600 psi (110 bar). Tabulation is based on spraying water at temperature at 70°F (21°C).

Spray Angle at 40 psi

Spray Tip Number

Equiv. Orifice Dia.

Capacity (gallons per minute)

Spray Pattern Width* at 1' Distance500

psi 1000 psi

1500 psi

2000 psi

3000 psi

4000 psi

110°

TP1100017- CDECRTC .011" .06 .08 .10 .12 .14 .16 15"

TP1100025-CDECRTC .013 " .09 .12 .15 .18 .22 .25 16"

TP1100039-CDECRTC .016" .14 .20 .24 .28 .34 .39 18"

TP1100050-CDECRTC .018" .18 .25 .30 .36 .43 .50 19-1/2"

TP110067-CDECRTC .021" .024 .33 .41 .47 .58 .67 20-1/2"

TP1100080-CDECRTC .023" .28 .40 .49 .57 .69 .80 22"

TP11001-CDECRTC .026" .35 .50 .61 .72 .86 1.00 23-1/2"

95°

TP950017-CDECRTC .011" .06 .08 .10 .12 .15 .17 13"

TP950039-CDECRTC .016" .14 .20 .24 .28 .34 .39 16"

80°

TP800039-CDECRTC .016" .14 .20 .24 .28 .34 .39 14"

TP800050-CDECRTC .018" .18 .25 .30 .36 .45 .50 15"

TP800055-CDECRTC .019" .19 .28 .34 .39 .48 .55 15"

TP800067-CDECRTC .021" .24 .33 .41 .47 .58 .67 16"

TP800080-CDECRTC .023" .28 .40 .49 .57 .69 .80 17-1/4"

65°

TP650017-CDECRTC .011" .06 .08 .10 .12 .14 .16 9.5"

TP650025-CDECRTC .013" .09 .12 .15 .18 .21 .24 10"

TP650039-CDECRTC .016" .14 .20 .24 .28 .34 .39 12"

TP650050-CDECRTC .018" .18 .25 .30 .36 .43 .50 13"

TP650067-CDECRTC .021" .24 .33 .41 .47 .58 .67 14-3/4"

50° TP500050-CDECRTC 0.018" .18 .25 .30 .36 .43 .50 11"

40° TP400055-CDECRTC .019" .19 .28 .34 .39 .48 .56 9"


Compatible Spray Guns

RotoClean® Airless Spray NozzlesBenefits

• Ideal for high-pressure manual paint spraying with Spraying Systems Co. and other manufacturers’ airless spray guns

• Quick and easy to unclog. Simply rotate tip 180° and blow obstructions out of the opening in the back of the tip

• Tungsten carbide orifice provides maximum erosion resistance for high-pressure spraying

• Easy to replace the orifice – no need to disassemble

• Guard safety feature

Specifications



Materials: Stainless steel holder with tungsten carbide orifice insert and protective nylon lugs

* Use Gasket No. 7894-NY for 106A-3.** Use Gasket No. 12552-NY for 106A-10.

RotoClean No. Connection Thread Size Gasket No. For

106A-2 225-2 11/16"-16 7894-NY SPRAYING SYSTEMS CO. 24 AUA AND GRACO

*106A-3 225-3 3/4"-16 19078-NY BALCRANK

106A-6 225-6 7/8"-14 11918-NY GRACO

106A-8 225-8 3/8" NPS 12552-NY NORDSON

106A-9 225-9 3/8" NPS 10660-NY DEVILBISS

**106A-10 225-10 3/4"-20 19079-NY BINKS 50

106A-11 225-11 M18 x 1 Metric 7894-NY ATLAS COPCO

106A-12 225-12 3/8" NPS 7894-NY SPEE-FLO

106A-13 225-13 M18 x 1 Metric 7894-NY DEICKE & KOPPERSCHMIDT

106A-14 225-14 1-14 9632-NY SPRAYING SYSTEMS CO. 44 AUA

106A-15 225-15 11/16"-16 12552-NY BINKS 43

106A-16 225-16 5/8"-14 BSPP 11918-NY —

106A-17 225-17 11/16"-16 13358-NY WAGNER

106A-18 225-18 M18 x 1.5 Metric 7894-NY —

225 RotoClean

106A RotoClean


* Tabulated capacities based on water.** Spray pattern width is based on liquid with viscosity of 20 seconds, #4 Zahn Cup spraying at 1600 psi (110 bar). Coverage will vary with viscosities and pressures.*** Available on special request.

RotoClean® Performance Data

RotoClean Insert Kits Capacity* (gallons per minute) Approx.**

Spray Pattern Width (at 1’

distance)

For 106A

Orifice Insert No. RC-

For 225 Handle/ Orifice Insert

No. 26081-

Equiv. Orifice Dia.

500 psi

1000 psi

1500 psi

2000 psi

WG 813 .013" .09 .12 .15 .18 16-1/2"

WH 815 .015" .12 .16 .20 .23 17"

WI — .016" .14 .20 .24 .28 18"

WJ 918 .018" .18 .25 .30 .36 19"

WK 1021 .021" .24 .33 .41 .47 21"

WA 1023 .023" .28 .40 .49 .57 22"

WL 1126 .026" .35 .50 .61 .72 23"

WM — .031" .53 .75 .91 1.1 25"

WN — .036" .71 1.0 1.2 1.4 26"

WO — .043" 1.1 1.5 1.8 2.1 27"

WP — .052" 1.4 2.0 2.5 2.8 28"

WQ — .057" 1.8 2.5 3.1 3.5 28"

WR — .062" 2.1 3.0 3.7 4.2 28"

WS — .067" 2.5 3.5 4.3 5.0 28"

WT — .072" 2.8 4.0 4.9 5.7 28"

WU — .076" 3.2 4.5 5.5 6.4 28"

WV — .078" 3.5 5.0 6.1 7.1 28"

WX — .089" 4.3 6.0 7.4 8.5 28"

9F 611 .011" .06 .08 .10 .12 13"

9G 713 .013" .09 .12 .15 .18 14"

9H 715 .015" .12 .16 .20 .23 15"

9I — .016" .14 .20 .24 .28 16"

9J 818 .018" .18 .25 .30 .36 17"

9K 921 .021" .24 .33 .41 .47 19"

9A 923 .023" .28 .40 .49 .57 19"

9L 1026 .026" .35 .50 .61 .72 21"

9M 1031 .031" .53 .75 .91 1.1 21"

9N 1036 .036" .71 1.0 1.2 1.4 22"

9O — .043" 1.1 1.5 1.8 2.1 22"

9P — .052" 1.4 2.0 2.5 2.8 23"

9Q — .057" 1.8 2.5 3.1 3.5 23"

9R — .062" 2.1 3.0 3.7 4.2 23"

9S — .067" 2.5 3.5 4.3 5.0 23"

9T — .072" 2.8 4.0 4.9 5.7 23"

9U — .076" 3.2 4.5 5.5 6.4 23"

9V — .078" 3.5 5.0 6.1 7.1 23"

9W — .085" 3.9 5.5 6.7 7.8 23"

9X — .089" 4.3 6.0 7.4 8.5 23"



distance)

For 106A



No. 26081-

Equiv. Orifice Dia.

500 psi

1000 psi

1500 psi

2000 psi

9Z — .099" 5.3 7.5 9.2 10.6 23"

8E — .009" .039 .055 .067 .078 10-1/2"

8F 511 .011" .06 .08 .10 .12 11-1/2"

8G 613 .013" .09 .12 .15 .18 12-1/2"

8H 615 .015" .12 .16 .20 .23 13"

8I — .016" .14 .20 .24 .28 14"

8J 718 .018" .18 .25 .30 .36 15"

8K 821 .021" .24 .33 .41 .47 17"

8A 823 .023" .28 .40 .49 .57 17"

8L 926 .026" .35 .50 .61 .72 19"

8M 931 .031" .53 .75 .91 1.1 19"

8N 936 .036" .71 1.0 1.2 1.4 19"

8O — .043" 1.1 1.5 1.8 2.1 19"

8P — .052" 1.4 2.0 2.5 2.8 19"

8Q — .057" 1.8 2.5 3.1 3.5 19"

8R — .062" 2.1 3.0 3.7 4.2 19"

8S — .067" 2.5 3.5 4.3 5.0 19"

8T — .072" 2.8 4.0 4.9 5.7 19"

8U — .076" 3.2 4.5 5.5 6.4 19"

8V — .078" 3.5 5.0 6.1 7.1 19"

8W — .085" 3.9 5.5 6.7 7.8 19"

8X — .089" 4.3 6.0 7.4 8.5 19"

*** — .093" 4.6 6.5 8.0 9.2 19"

*** — .096" 4.9 7.0 8.6 9.9 19"

8Z — .099" 5.3 7.5 9.2 10.6 19"

7G — .012" .08 .11 .14 .16 11-1/2"

7I — .016" .14 .20 .24 .28 13"

6D — .007" .028 .04 .049 .057 8-1/2"

6E — .009" .039 .055 .067 .078 9-1/4"

6F — .011" .06 .08 .10 .12 10"

6G 513 .013" .09 .12 .15 .18 10-1/2"

6H 515 .015" .12 .16 .20 .23 11"

6I — .016" .14 .20 .24 .28 12"

*** *** .017" .16 .22 .27 .31 12-1/2"

6J 618 .018" .18 .25 .30 .36 13"

*** *** .019" .19 .28 .34 .39 13"

6K 721 .021" .24 .33 .41 .47 15"

6A 723 .023" .28 .40 .49 .57 15"

6L 726 .026" .35 .50 .61 .72 16"






distance)

For 106A



No. 26081-

Equiv. Orifice Dia.

500 psi

1000 psi

1500 psi

2000 psi

6M 731 .031" .53 .75 .91 1.1 16"

6N 736 .036" .71 1.0 1.2 1.4 16"

6O — .043" 1.1 1.5 1.8 2.1 16"

6P — .052" 1.4 2.0 2.5 2.8 16"

6Q — .057" 1.8 2.5 3.1 3.5 16"

6R — .062" 2.1 3.0 3.7 4.2 16"

6S — .067" 2.5 3.5 4.3 5.0 16"

6T — .072" 2.8 4.0 4.9 5.7 16"

6U — .076" 3.2 4.5 5.5 6.4 16"

6V — .078" 3.5 5.0 6.1 7.1 16"

6W — .085" 3.9 5.5 6.7 7.8 16"

6X — .089" 4.3 6.0 7.4 8.5 16"

*** — .093" 4.6 6.5 8.0 9.2 16"

*** — .096" 4.9 7.0 8.6 9.9 16"

6Z — .099" 5.3 7.5 9.2 10.6 16"

5D — .007" .028 .04 .049 .057 7-3/4"

5E — .009" .039 .055 .067 .078 8"

5F 411 .011" .06 .08 .10 .12 8-1/2"

5G 413 .013" .09 .12 .15 .18 9"

5H 415 .015" .12 .16 .20 .23 10"

5I — .016" .14 .20 .24 .28 10-1/2"

*** *** .017" .16 .22 .27 .31 10-1/2"

5J 518 .018" .18 .25 .30 .36 11"

*** *** .019" .19 .28 .34 .39 11"

5K 621 .021" .24 .33 .41 .47 12"

5A 623 .023" .28 .40 .49 .57 13"

5L 626 .026" .35 .50 .61 .72 14"

5M 631 .031" .53 .75 .91 1.1 14"

5N 636 .036" .71 1.0 1.2 1.4 14"

5O — .043" 1.1 1.5 1.8 2.1 14"

5P — .052" 1.4 2.0 2.5 2.8 14"

5Q — .057" 1.8 2.5 3.1 3.5 14"

5S — .067" 2.5 3.5 4.3 5.0 14"

5T — .072" 2.8 4.0 4.9 5.7 14"

5V — .078" 3.5 5.0 6.1 7.1 14"

5Z — .099" 5.3 7.5 9.2 10.6 14"

4B — .005" .014 .020 .025 .028 6-1/2"

4C — .006" .021 .030 .037 .042 6-1/2"

4D — .007" .028 .040 .049 .057 6-1/2"



distance)

For 106A



No. 26081-

Equiv. Orifice Dia.

500 psi

1000 psi

1500 psi

2000 psi

4E — .009" .039 .055 .067 .078 7"

4F 311 .011" .06 .08 .10 .12 7-1/2"

4G 313 .013" .09 .12 .15 .18 8"

4H — .015" .12 .16 .20 .23 8-1/2"

4I — .016" .14 .20 .24 .28 9"

*** *** .017" .16 .22 .27 .31 9-1/2"

4J 418 .018" .18 .25 .30 .36 10"

*** *** .019" .19 .28 .34 .39 10"

4K 521 .021" .24 .33 .41 .47 11"

4A 523 .023" .28 .40 .49 .57 11"

4L 526 .026" .35 .50 .61 .72 12"

*** *** .029" .46 .65 .80 .92 12"

4M 531 .031" .53 .75 .91 1.1 12"

4N 536 .036" .71 1.0 1.2 1.4 12"

4O — .043" 1.1 1.5 1.8 2.1 12"

4P — .052" 1.4 2.0 2.5 2.8 12"

4Q — .057" 1.8 2.5 3.1 3.5 12"

4R — .062" 2.1 3.0 3.7 4.2 12"

4S — .067" 2.5 3.5 4.3 5.0 12"

4T — .072" 2.8 4.0 4.9 5.7 12"

4U — .076" 3.2 4.5 5.5 6.4 12"

4V — .078" 3.5 5.0 6.1 7.1 12"

4Z — .099" 5.3 7.5 9.2 10.6 12"

3B — .005" .014 .020 .025 .028 5"

3C — .006" .021 .030 .037 .042 5"

3D — .007" .028 .040 .049 .057 5-1/2"

3E — .009" .039 .055 .067 .078 5-1/2"

3F — .011" .06 .08 .10 .12 6"

3G — .013" .09 .12 .15 .18 6"

3H 315 .015" .12 .16 .20 .23 7"

3I — .016" .14 .20 .24 .28 7"

3J 318 .018" .18 .25 .30 .36 7"

*** *** .019" .19 .28 .34 .39 7"

3K 421 .021" .24 .33 .41 .47 8"

3A 423 .023" .28 .40 .49 .57 8-1/2"

3L 426 .026" .35 .50 .61 .72 9"

3M 431 .031" .53 .75 .91 1.1 9"

3N 436 .036" .71 1.0 1.2 1.4 9"

3O — .043" 1.1 1.5 1.8 2.1 9"




Nozzle Type A B Net Weight

106A 5.375" 2.125" 8.5 oz

225 2.437" 2" 4.2 oz



A A 1 0 6 A – 2 + r C 2 F | | RotoClean Orifice Insert Number Kit

A A 2 2 5 – 6 + 2 6 0 8 1 - 8 1 3 | | RotoClean Orifice/Handle Number Insert Kit

106A rotoClean

225 rotoClean




distance)

For 106A



No. 26081-

Equiv. Orifice Dia.

500 psi

1000 psi

1500 psi

2000 psi

3P — .052" 1.4 2.0 2.5 2.8 9"

3R — .062" 2.1 3.0 3.7 4.2 9"

3T — .072" 2.8 4.0 4.9 5.7 9"

2B — .005" .014 .020 .025 .028 4"

2C — .006" .021 .030 .037 .042 4"

2D — .007" .028 .040 .049 .057 4-1/2"

2E — .009" .039 .055 .067 .078 4-1/2"

2F 211 .011" .06 .08 .10 .12 5"

2G 213 .013" .09 .12 .15 .18 5"

2H 215 .015" .12 .16 .20 .23 5-1/2"

2I — .016" .14 .20 .24 .28 6"

*** *** .017" .16 .22 .27 .31 6"

2J — .018" .18 .25 .30 .36 6"

2K 321 .021" .24 .33 .41 .47 6-1/2"

2A 323 .023" .28 .40 .49 .57 7"

2L 326 .026" .35 .50 .61 .72 7"

2M 331 .031" .53 .75 .91 1.1 7"

2N 336 .036" .71 1.0 1.2 1.4 7"

2O — .043" 1.1 1.5 1.8 2.1 7"

2P — .052" 1.4 2.0 2.5 2.8 7"

2R — .062" 2.1 3.0 3.7 4.2 7"

2T — .072" 2.8 4.0 4.9 5.7 7"

1B — .005" .014 .020 .025 .028 3"

1D — .007" .028 .040 .049 .057 3-1/2"



distance)

For 106A



No. 26081-

Equiv. Orifice Dia.

500 psi

1000 psi

1500 psi

2000 psi

1E — .009" .039 .055 .067 .078 3-1/2"

1F — .011" .06 .08 .10 .12 4"

1G — .013" .09 .12 .15 .18 4"

1H — .015" .12 .16 .20 .23 4-1/2"

1I — .016" .14 .20 .24 .28 5"

1J 218 .018" .18 .25 .30 .36 5"

1K 221 .021" .24 .33 .41 .47 5-1/2"

1A 223 .023" .28 .40 .49 .57 5-1/2"

1L 226 .026" .35 .50 .61 .72 6"

1M 231 .031" .53 .75 .91 1.1 6"

1N 236 .036" .71 1.0 1.2 1.4 6"

0B — .005" .014 .020 .025 .028 2-1/2"

0D — .007" .028 .040 .049 .057 2-1/2"

0E — .009" .039 .055 .067 .078 2-1/2"

0F — .011" .06 .08 .10 .12 3"

0G — .013" .09 .12 .15 .18 3"

0H — .015" .12 .16 .20 .23 3-1/2"

0I — .016" .14 .20 .24 .28 4"

0J — .018" .18 .25 .30 .36 4"

0K — .021" .24 .33 .41 .47 4"

0L — .026" .35 .50 .61 .72 4"

0M — .031" .53 .75 .91 1.1 4"

0N — .036" .71 1.0 1.2 1.4 4"

B

B

A

A

North Avenue and Schmale Road, P.O. Box 7900, Wheaton, IL 60187-7901 USA

Tel: 1.800.95.SPRAY Intl. Tel: 1.630.665.5000 Fax: 1.888.95.SPRAY Intl. Fax: 1.630.260.0842

www.spray.com

Bulletin No. 644 Printed in the U.S.A. ©Spraying Systems Co. 2011

SprayNozzles

SprayControl

SprayAnalysis

SprayFabrication

Benefits

• Ideal for applications requiring a fine finish. Insert the Model HV orifice in the inlet of standard TC spray tips

• Produces a flat spray pattern with feathering spray pattern edges

Accessories

Capacity Size

Used With TC Tip

Tip Type Equiv. Orifice Dia.

8 -0008TC .007"

10 -0011TC .009"

12 -0017TC .011"

14 -0025TC .013"

16 -0033TC .015"

17 -0039TC .016"

19 -0050TC .018"

22 -0067TC .021"

24 -0080TC .023"

27 -01TC .026"

Model HV Orifice Performance Data

Orifice Type A B Net Weight

HV .25" .593" .32 oz

Dimensions & WeightsH v – 8

| | Orifice Type Capacity Size

Model Hv Orifice insert


Model HV Orifice

B

A

Tip Retainer

Spray Tip

Screen Strainer

Gasket

Tip Gasket

High-Pressure Female

Nozzle Body

High-Pressure 11430 UniJet® Nozzle Body


Benefits

• Nozzle replacement costs are low because only the spray tips are replaced; the nozzle body can be reused

• Spray tip replacement is quick and easy – simply unscrew the tip retainer cap

• Interchangeable spray tips are available in a wide variety of spray patterns, spray angles and capacity sizes

• Orifice inserts, cores and strainers can be easily removed for inspection or cleaning

• Built-in strainer further prevents wear by keeping debris from entering the nozzle orifice; critical in applications using recirculated water

Documents

Tungsten Carbide (TC) Tips for High-Pressure SprayingTungsten Carbide (TC) Tips for High-Pressure Spraying Spray Nozzles Spray Control Spray ... 2000 psi (138 bar) Hollow cone •