Type MF - Type MF Specifically developed for use with MetFloorآ® 60 and MetFloorآ® 80 profiles manufactured page 1
Type MF - Type MF Specifically developed for use with MetFloorآ® 60 and MetFloorآ® 80 profiles manufactured page 2

Type MF - Type MF Specifically developed for use with MetFloorآ® 60 and MetFloorآ® 80 profiles manufactured

  • View
    0

  • Download
    0

Embed Size (px)

Text of Type MF - Type MF Specifically developed for use with MetFloorآ® 60 and MetFloorآ® 80 profiles...

  • ® +44 (0) 1274 521444www.Lindapter.com© Lindapter International 2019

    For Characteristic Resistances when designing a connection to Eurocode 3, please refer to DoP No.017 on the website www.Lindapter.com/About/CE

    Decking Fixings by Lindapter® | 63

    Type MF Specifically developed for use with MetFloor® 60 and MetFloor® 80 profiles manufactured by Composite Metal Flooring (CMF®).

    Bracket

    Safe Working Load (FOS 3:1)

    Product Code Rod min 4.6 Tensile / 1 Rod Tightening Torque

    kN Nm

    MF06 M6 1.47 10

    MF08 M8 1.47 10

    MF10 M10 1.47 10

    Bracket: Steel strip, zinc plated + JS500 Wedge: Malleable iron, zinc plated.

    How to install...

    1) Pre-assemble the bracket and wedge (flat surface facing up) onto the threaded rod and insert one side of the bracket into

    the re-entrant channel of decking.

    2) Insert the other side of the bracket into position inside the decking.

    3) Turn the wedge clockwise until the position in Fig. 4 has been achieved.

    4) Tighten the nut on the rod to a torque of 10Nm (prevent rod from rotating).

    1. 2. 3. 4.

    If the decking profile is deformed or distorted, do not install the fixing. If in doubt, contact the Technical Support team for advice.

    Install the decking fixings after the concrete has been poured and has reached full strength.

    Although the Type MF is similar in appearance to the Type MW2 (page 64), it should NOT be used in profiles manufactured by Kingspan® Structural Products.

    Wedge G IR

    D E

    R C

    L A

    M P

    S R

    A IL

    F IX

    IN G

    S L

    IF T

    IN G

    P O

    IN T

    S H

    O L

    L O

    -B O

    LT F

    L O

    O R

    F IX

    IN G

    S S

    U P

    P O

    R T

    F IX

    IN G

    S D

    E C

    K IN

    G F

    IX IN

    G S

  • Compatible Profiles Lindapter has developed an extensive range of CE Marked decking fixings to ensure optimum compatibility with all major decking profiles.

    Components

    Also available

    Type TC - Toggle Clamp page 69

    Designed for: Service suspension from pre-cast hollow core slabs (minimum core depth of 75mm) as well as Structural Hollow Section (SHS), steel sheeting or purlins.

    Lindapter Decking Fixing Compatible Composite Decking Profile(s)

    Type TR60 page 62

    Structural Metal Decks (SMD) TR60+ and TR80+

    Type MF page 63

    Composite Metal Flooring (CMF®) MetFloor® 60 and MetFloor® 80

    Type MW2 - Multiwedge 2 page 64

    Kingspan® Structural Products Multideck® 60 and Multideck® 80

    Type AW - Alphawedge page 65

    Hare Decking (formerly Richard Lees®) Ribdeck® E60

    Type AMD page 66

    Anglian Metal Deck AMD60 and AMD80

    Type SD2 - Slimdek 2 page 67

    Tata Steel® Europe ComFlor® 225

    Type VN page 68

    Fits several profiles including: AMD54 (AMD), R51+ (SMD), ComFlor® 51+ (Tata Steel®), Holorib® (Hare Decking), Superib® (Hare Decking), Multideck® 50 (Kingspan®) and MetFloor® 55 (CMF®)

    G IR

    D E

    R C

    L A

    M P

    S R

    A IL

    F IX

    IN G

    S L

    IF T

    IN G

    P O

    IN T

    S H

    O L

    L O

    -B O

    LT F

    L O

    O R

    F IX

    IN G

    S S

    U P

    P O

    R T

    F IX

    IN G

    S D

    E C

    K IN

    G F

    IX IN

    G S

    ® +44 (0) 1274 521444www.Lindapter.com© Lindapter International 2019

    Decking Fixings by Lindapter® | 61