Vortec v 8 Harness

  • Published on
    30-Dec-2015

  • View
    84

  • Download
    0

Embed Size (px)

Transcript

  • VORTEC Wiring HarnessINSTRUCTIONS & SUPPLEMENTAL INFORMATION

    4.3 / 5.0 / 5.7 / 7.4

    Street && PPerformance#1 Hot Rod Lane ~ Mena, AR 71953

    Phone 479-394-5711 ~ Fax 479-394-7113email sales@hotrodlane.cc ~ www.hotrodlane.cc

  • 1. Fuse Block.

    2. A.L.D.L Connector (diagnostic link for plugging in scanner).

    3. Fuel Pump Relay. (NOTE: AC DELCO EP 381 Fuel Pump is needed to supply 65 P.S.I fuel pressure.)

    4. Color Coded PCM (computer) Connectors (4) Red, Blue, Black, and Gray.

    5. Tan wire goes to the check engine light. Must supply a 12 volt hot wire to the bulb, the tan wire is the ground to complete the circuit.

    6. Red wire should have 12VDC in crank and run.

    7. White wire is optional TACH signal wire - Ground Side.

    8. Black wire ground to back of block or head. BE SURE to clean contact point. Ground battery to engine or transmission, engine to body, and engine to frame.

    9. Three prong plug with a purple water type seal goes to cam sensor

    10. Three prong plug with light green seal with orange, brown and white wires, go to three prong oil pressure switch and the white wire that runs from this plug, is used with GM compatible gauges, But if you use VDO Stewart Warner, ect, you must use their sending unit.

    11. Passenger side O2.

    12. Driver side O2.

    13. Red plug with gray seal and green and red wire, is the Canister Purge. Only needed if doing an emission legal system.

    14. EGR Solenoids Black plug with gray seal and gray and black wires. Only needed if doing an emission legal system.

    15. Orange wire with quick burn fusible link, goes to the hot battery starter. If you are using a battery disconnect you must be on the hot side of the disconnect.

    16. Gray plug with blue seal with five wires goes to the Lenoir EGR. ( Not needed in NON EMISSION applications.)

    17. Blue wire with a black plug goes to the Knock Sensor.

    18. Black plug with blue seal and light green and black wire, goes to the Engine Temp Sensor at the front of the intake.

    19. Dark brown wire is the HOT lead, to the electric fuel pump (fuse and relay is in the harness).

    20. Black plug with blue seal and yellow and purple twisted wire, goes to the vehicle speed senor in the tail housing of the transmission.

    21. Black plug with blue seal and four wires, goes to the Idle Air Motor at the front of the intake.

    22. Black round plug with the purple seal, goes to the Throttle Position Sensor

    23. Injector plug goes to the main injector plug located behind the throttle body.

    24. Gray plug with a purple seal and light green and gray wires, go to the MAP Sensor.

    25. Black plug with purple seal and yellow, black, and red wires, go to the MASS AIR FLOW.

    26. Tan plug with purple seal and red, white and blue wires, go to the Coil.

    27. Black plug with blue seal and red, white, black, and blue wires, go to the Coil Driver.

    28. Black plug with purple seal and violet, yellow and red wires, go to the Crank Sensor.

    Street & Performance 5.0 / 5.7VORTEC Std or 4L60E / 4L80E Transmission

  • 28

    1

    2

    4

    6

    57

    3

    8

    10

    27

    26

    9

    24

    25

    23

    21

    22

    28

    20

    19

    17

    18

    16

    12

    11

    13

    14

    15

    Street & PerformanceSmall Block 5.0 / 5.7VORTECWiring Harness

    4 Plugs to ComputerRed, Blue, Black and Gray.

    Blue Plug

    Black Plug

    White Plug

    Red Plug

  • Canister Purge (13) Coil Module (27) Coil Plug (26)

    MAP Sensor(24)

    Injector Plug(23)

    Fuel Inlet 16mm

    Fuel Return14mm

    E.G.R Valve Throttle PositionSensor (22)

    Idle SpeedMotor (21)

    P.C.V (4)Shrader valve tocheck fuel pressure

    Coolant Temp(18)

    Coil Plug (26)

    Coil Driver (27) MAP Sensor (24) Canister Purge (13)

    (NOTE: AC DELCO EP 381 Fuel Pump is needed to supply 65 P.S.I fuel pressure.)

    Small Block VORTECManifold

  • Throttle PositionSensor

    Idle Speed Motor

    Injector Plug

    Vortec DistributorThese can be purchased NEW from Street & Performance

    MAP Sensor

    Big Block VORTECManifold

  • Coolant Temp

    Canister Purge Valve

    Fuel Inlet

    Return Fuel Line

    Vacuum FuelPressure Regulator

    (NOTE: AC DELCO EP 381 Fuel Pump is needed to supply 65 P.S.I fuel pressure.)

    E.G.R Valve

    Coil

    Injector Plug

    Injectors arelocated inside the

    manifold.

  • GM 1996-00 4.3 / 5.0 / 5.7 / 7.4 VORTEC CPFI

    ENGINE YEAR COMPUTER NUMBER

    1996-97 4.3L 16244210 199616208546 199616229684 1997

    1998-00 4.3L 16250279 199809355699 199816263494 1999-00

    1996-97 5.0 / 5.7L 16244210 199616208546 199616229684 1997

    1998-00 5.0 / 5.7L 16250279 199809355699 199816263494 1999-00

    1996-97 7.4L 16244210 199616208546 199616229684 1997

    1998-00 7.4L 16250279 199809355699 199816263494 1999-00

    3rd Digit - Make 4th Digit 8th Digit - Engine 10th Digit - Year

    T (Chevrolet) E J - 7.4L (454)M - 5.0L (305)R - 5.7L (350)W - 4.3L (262)X - 4.3L (262)

    T - 1996V - 1997W- 1998X - 1999Z - 2000

    VIN# I.D. IDENTIFIERS

  • GM BIG BLOCK VORTEC INJECTOR ASSEMBLY

    GM SMALL BLOCK VORTECINJECTOR ASSEMBLY

    GM V6 VORTEC INJECTOR ASSEMBLY

    INLET 16mm O-Ring

    RETURN 14mm O-Ring

    LARGE FITTING INLET 16mm to O-Ring

    14mm O-Ring ReturnRegulator Return

  • 17

    18

    23

    21

    22

    24

    2526

    27

    28

    29 30

    35

    34

    33

    3231

    20

    19

    13

    12

    1615

    11

    14

    5 6 7 8 9

    4

    3 2

    10

    1

    Street & PerformanceBig Block VORTECWiring Harness

    4 Plugs to ComputerRed, Blue, Black and Gray.

  • Street & Performance Big Block VORTEC 7.4 Std or 4L80E Transmission

    1. Fuel Pump Relay.

    2. A.L.D.L Connector ( Diagnostic link for scanner).

    3. Fuse Panel.

    4. Ignition Switch (red wire,12 volt with key on and in start position).

    5. Tachometer (white wire).

    6. 4000 Pulse vehicle speed signal for Speedometer (Green wire).

    7. Cruise Control (yellow wire).

    8. Brake Light Switch (purple wire) Normally closed for torque converter lockup.

    9. Check Engine Light (brown wire) You must supply 12 volts supply to 12 volt bulb, this wire is the ground side to complete the circuit.

    10. Black wire ground to back of block or head. BE SURE to clean contact point. Ground battery to engine or transmission, engine to body, and engine to frame.

    11. Cam Sensor (three prong plug, black with purple seal.

    12. Oil Pressure wire (USED with GM compatible gauges, NOT USED with any other brand of gauges).

    13. Oil Pressure sending unit ( Part # 25036553 Three prong with brown and orange wire).

    14. Direct to Fuel Pump (brown wire).

    15. Cam Plug (Three prong plug with purple seal).

    16. Coil Driver (Three prong plug with blue seal).

    17. Driver side / Passenger side Knock sensor wire (blue wire).

    18. Hot fused link to main post on starter (orange wire).

    19. Driver side injector plugs (end plug has red and black wires).

  • Street & Performance Big Block VORTEC 7.4 Std or 4L80E Transmission

    20. Passenger side injector plug (end plug has blue and red wires).

    21. Passenger side Oxygen sensor (four prong plug).

    22. Driver side Oxygen sensor (four prong plug).

    23. Engine Temp black plug with blue seal and yellow and black wire).

    24. MAP Sensor (gray plug with purple seal 3 prong plug gray green black wire).

    25. Lenoir E.G.R(NOT USED on NON EMISSION VEHICLES) (five prong gray plug with purple seal).

    26. Canister purge (NOT USED on NON EMISSION VEHICLES)( two wire RED Plug).

    27. E.G.R solenoid (NOT USED on NON EMISSION VEHICLES)( black two prong plug with gray seal).

    28. Idle Air Speed (Four prong black plug with blue seal).

    29. Throttle Position Sensor (round three prong plug with purple seal).

    30. Vehicle Speed output (black Plug with blue seal and twisted yellow and purple wire).

    31. Vehicle Speed input (black Plug with blue seal and twisted blue and red wire).

    32. 4L80E Transmission plug (large gray plug).

    33. MAF (three prong black plug with purple seal, red, yellow and black wire).

    34. Air Temp Sensor (gray plug blue seal, black and brown wire).

    35 Crank Sensor ( black plug with purple seal with red, purple and yellow wires).

  • DTC P0101 Mass Air Flow System PerformanceDTC P0102 MAF Sensor Circuit Low FrequencyDTC P0103 MAF Sensor Circuit High FrequencyDTC P0106 MAP System PerformanceDTC P0107 MAP Sensor Circuit Low VoltageDTC P0108 MAP Sensor Circuit high VoltageDTC P0112 IAT Sensor Circuit Low VoltageDTC P0113 IAT Sensor Circuit High VoltageDTC P0117 ECT Sensor Circuit Low VoltageDTC P0118 ECT Sensor Circuit High VoltageDTC P0121 TP Sensor PerformanceDTC P0122 TP Sensor Circuit Low VoltageDTC P0123 TP Sensor Circuit High VoltageDTC P0125 ECT Excessive Time to Closed LoopDTC P0131 HO2S Circuit Low Voltage Bank 1 Sensor 1DTC P0132 HO2S Circuit High Voltage Bank 1 Sensor 1DTC P0133 HO2S Slow Response Bank 1 Sensor 1DTC P0134 HO2S Insufficient Activity Bank 1 Sensor 1DTC P0135 HO2S Heater Circuit Bank 1 Sensor 2DTC P0137 HO2S Circuit Low Voltage Bank 1 Sensor 2DTC P0138 HO2 S Circuit High Voltage bank 1 Sensor 2DTC P0140 HO2S Insufficient Activity Bank 1 Sensor 2DTC P0141 HO2S Heater Circuit Bank 1 Sensor 2DTC P0143 HO2S Circuit Low Voltage Bank 1 Sensor 3DTC P0144 HO2S Circuit High Voltage Bank 1 Sensor 3DTC P0146 HO2S Insufficient Activity Bank 1 Sensor 3DTC P0147 HO2S Heater Circuit Bank 1 Sensor 3DTC P0151 HO2S Circuit Low Voltage Bank 2 Sensor 1DTC P0152 HO2S Circuit High Voltage Bank 2 Sensor 1DTC P0153 HO2S Slow Response Bank 2 Sensor 1DTC P0154 HO2S Insufficient Activity Bank 2 Sensor 2DTC P0155 HO2S Heater Circuit Bank 2 Sensor 1DTC P0157 HO2S Circuit Low Voltage Bank 2 Sensor 2DTC P0158 HO2S Circuit High Voltage Bank 2 Sensor 2DTC P0160 HO2S Insufficient Activity Bank 2 Sensor 2DTC P0161 HO2S Heater Circuit Bank 2 Sensor 2DTC P0171 Fuel Trim System Lean Bank 1DTC P0172 Fuel Trim System Rich Bank 1DTC P0174 Fuel Trim System Lean Bank 2DTC P0175 Fuel Trim System Rich Bank 2DTC P0300 Engine Misfire DetectedDTC P0301 Cylinder 1 Misfire DetectedDTC P0302 Cylinder 2 Misfire DetectedDTC P0303 Cylinder 3 Misfire DetectedDTC P0304 Cylinder 4 Misfire Detected

    VORTECVORTECDTCDTC TROUBLETROUBLE CODESCODES

  • DTC P0305 Cylinder 5 Misfire DetectedDTC P0306 Cylinder 6 Misfire DetectedDTC P0307 Cylinder 7 Misfire DetectedDTC P0308 Cylinder 8 Misfire DetectedDTC P0325 Knock Sensor CircuitDTC P0327 Knock Sensor Noise Channel Low VoltageDTC P0336 CKP Sensor Circuit PerformanceDTC P0337 CKP Sensor Circuit Low FrequencyDTC P0338 CKP Sensor Circuit High FrequencyDTC P0339 CKP Sensor Circuit IntermittentDTC P0340 CMP Sensor CircuitDTC P0341 CMP Sensor Circuit PerformanceDTC P0401 EGR System Flow InsufficientDTC P0410 AIR System DTC P0420 TWC System Low Efficiency Bank 1DTC P0430 TWC System Low Efficiency Bank 2DTC P0440 EVAP SystemDTC P0441 EVAP System No Flow During PurgeDTC P0442 EVAP Control System Small Leak DetectedDTC P0446 EVAP Canister Vent BlockedDTC P0461 Fuel Level Sensor Circuit PerformanceDTC P0462 Fuel Level Sensor Circuit Low VoltageDTC P0463 Fuel Level Sensor Circuit High VoltageDTC P0500 Vehicle Speed Sensor CircuitDTC P0506 Idle Control System Low RPMDTC P0507 Idle Control System High RPMDTC P0704 Clutch Switch CircuitDTC P1106 MAP Sensor CKT Intermittent High VoltageDTC P1107 MAP Sensor CKT Intermittent Low VoltageDTC P1111 IAT Sensor CKT Intermittent High VoltageDTC P1112 IAT Sensor CKT Intermittent Low VoltageDTC P1114 ECT Sensor CKT Intermittent Low VoltageDTC P1115 ECT Sensor CKT Intermittent High VoltageDTC P1121 TP Sensor CKT Intermittent High VoltageDTC P1122 TP Sensor CKT Intermittent Low VoltageDTC P1133 HO2S Insufficient Switching Bank 1 Sensor 1DTC P1134 HO2S Transition Time Ratio Bank 1 Sensor 1DTC P1153 Insufficient Switching Bank 2 Sensor 1DTC P1154 HO2S Transition Time Ratio Bank 2 Sensor 1DTC P1345 CKP/CMP Correlation DTC P1351 IC Circuit High VoltageDTC P1361 ID Circuit Low VoltageDTC P1380 EBCM DTC Rough Road Date UnusableDTC P1381 Misfire Detected No EBCM/VCM Serial Data DTC P1406 EGR Valve Pintle Position CircuitDTC P1415 AIR System Bank 1DTC P1416 AIR System Bank 2DTC P1441 EVAP System Flow During Non-PurgeDTC P1508 IAC System Low RPMDTC P1509 IAC System High RPM

  • OTHER VORTEC PRODUCTS AVAILABLE FROMSTREET & PERFORMANCE

    Ph. 479-394-5711Fax. 479-394-7113

    S&P can provide youwith Quality AC DelcoParts, saving you fromhaving to go to the partstore and assuring thatyou have the right parts.

    Custom length braided fuel lines made to fit your application with quality Aeroquip performance products. S&Pstocks a complete line of hoses and fittings for fuel lines andpower steering.

    AC DELCO O2 Sensors

    Street & Performance Fuel Filter Kit.

    Includes Genuine AC Delco FuelFilter, Street & Performance Filter Bracket and Fittings.

    VORTEC Computersare black with fiveplugs. The 94-97 LT-1computers are silverwith four connectionplugs.

    Small Plug Not Used

    I.D Service Number

    Polished Fuel Line Fittings

    16mm O-Ring to AN614mm O-Ring to AN6

  • #1 Hot Rod LaneMena, Arkansas 71953

    Ph. 479-394-5711 Fax. 479-394-7113www.hotrodlane.cc

    Hook to red brake wire12 Volts ALL THE TIMEwith brake OFF.NO VOLTAGE WITH BRAKE ON!

    12 Volts In 12 Volts In

    For brake light12 Volts with brake on ONLY

    GM Brake Switch #25524845AC Delco #D850A

    If you have a 2 prong pressure brake switch, you will need this brake switch relay kit.