BRACKET PART 4383

ASSEMBLY

HAIRPIN COTTER PART S-52-6

Mount clutch rod mounting assembly plate, part 4291 to engine face by removing K6 xl" bolt (which holds lower belt guide angle on) and place plate assembly in position. Replace bolt and lock washer and tighten.

Install bracket, part 4383 to tractor hood stand with two ~6-18 x ~ hex bolts, part 908015-4 and two ~6 dia. lockwasher, part 920082-4.

Insert the ~ x ~ x 1 K/' key, part 1121 into key­way on engine shaft. Slide clutch plate assembly, part 4282, on to shaft until engine shaft is against snap ring inside clutch plate assembly. Secure in place by tightening set screw, part 909848-6, with allen wrench, part 5-56-6.

Slide clutch housing, part 5195, on to the engine the engine shaft until it comes into contact with clutch plate.

Install clutch rod assembly, part 4355 down thru one of the holes in the bracket, part 4383. Until t~e forked shaped part of the rod is between the two Ye nuts on clutch rod mounting assembly plate, part 4291. Insert hair pin cotter, part 5-52-6 through clutch housing and into plate on clutch rod.

POWER TAKE·OFF MODEL 8-3411

(Formerly PT-5)

CLUTCH HOUSING PART 5195

CLUTCH ROD MOUNTING ASS'Y.

PART 4291

CLUTCH OPERATION AND ADJUSTMENT Attaching tools are started and ,stopped by oper­

ating the engine mounted P.T.O. By moving the clutch rod from the outside notch in the bracket, to the inside notch, (toward the troctor), the friction clutch is engaged. The other end of this rod is fork shaped with a Ye" locknut on each side. By moving these nuts in toward the tractor" more tension will be applied to the clutch. Adjust nuts so that clutch just disengages with clutch rod in middle notch (above arrow) of bracket, part 4383. Refer to decal on bracket. There are two grooves in the clutch for V-Belts, be sure the main drive belt is in the larger of the two. (Closest to the engine.) The other small groove is to drive other attaching tools.

LUBRICATION The clutch housing has a needle bearing pressed

inside with a grease seal. This bearing has been greased at the factory. Every 25 hours the clutch housing should be removed and a SMALL amount of good quality grease applied to partially fill the spaces between the rollers.

PARTS LIST

When Qrderi"9 part. alway. II.t Part No. and neme of part.

Ref. Part No. Ref. Part No. No. No. Description Req'd. No. No. Description Req'd.

1 5195 Housing 13 5196 Bearing - Ball

2 4398 Seal 14 5-51-112 Snap Ring - 1 Ye Int. Truarc

3 4397 Bearing Needle 15 5-51-175 Snap Ring - 1 % Int. Truarc 4 4282 Assembly - Clutch Plate & Face Complete 16 4383 Bracket 1

5 4874 As,embly - Clutch Plate • Sleeve 17 908015-4 Bolt. Hex. ~6-18 x ~ 2 6 4365 Facing 18 920082-4 lockwasher . ~6 Dia. 2 7 4870 Rivet - SAE #4 Tubular 6 19 4291 Assembly Plote . Clutch Rod Mfg. 8 909848·6 Set Screw - Nylock ~ ·20 x ~ 20 4355 Assembly - Clutch Rod 9 5197 Shaft - Clutch Engagement 21 2709 Knob 1

10 5·50-75 Snap Ring . % Ext. Truarc 22 915663·4 Nut . % -16 Elastic Slop 2 11 5·52-6 Hair Pin 23 5194 Decal • Clutch Adj. Inslr.

12 1121 Key . ~ x ~ x 1~6 24 5-56-6 Wrench ~" Allen (Ye Hex)

6· '8·64 FORM NO. 208

PARTS LIST AND INSTRUCTIONS

WHEELHORSE PRODUCTS, INC. • SOUTH BEND, IND.

BRACKET PART 4383

ASSEMBLY

Mount clutch rod mounting assembly plate, part 4291 to engine face by removing K6 x 1" bolt (which holds lower belt guide angle on) and place plate assembly in position. Replace bolt and lock washer and tighten.

Install bracket, part 4383 to tractor hood stand with two 716-18 x ~ hex bolts, part 908015-4 one! two 716 dia. lockwasher, part 920082-4.

Insert the %I x %I X H(6" key, part 1121 into key­way on engine shaft. Slide clutch plate assembly, part 4282, on to shaft until engine shaft is against snap ring inside clutch plate assembly. Secure in place by tightening set screw, part 909848-6, with allen wrench, part 5-56-6.

Slide clutch housing, part 5195, on to the engine the engine shaft until it comes into contact with clutch plate.

Install clutch rod assembly, part 4355 down thru one of the holes in the bracket, part 4383. Until the forked shaped part of the rod is between the two % nuts on clutch rod mounting assembly plate, part 4291. Insert hair pin cotter, part 5-52-6 through clutch housing and into plate on clutch rod.

POWER TAKE·OFF MODEL 8-3411

(Formerly PT-S)

CLUTCH HOUSING PART 5195

CLUTCH ROD MOUNTING ASS'Y.

PART 4291

CLUTCH OPERATION AND ADJUSTMENT Attaching tools are started and stopped by oper­

ating the engine mounted P.T.C. By moving the clutch rod from the outside notch in the bracket, to the inside notch, (toward the tractor), the friction clutch is engaged. The other end of this rod is fork shaped with a %" locknut on each side. By moving these nuts in toward the tractor, more tension will be applied to the clutch. Adjust nuts so that clutch just disengages with clutch rod in middle notch (above arrow) of bracket, part 4383. Refer to decal on bracket. There are two grooves in the clutch for V-Belts, be sure the main drive belt is in the larger of the two. (Closest to the engine.) The other small groove is to drive other attaching tools. LUBRICATION

The clutch housing has a needle bearing pressed inside with a grease seal. This bearing has been greased at the factory. Every 25 hours the clutch housing should be removed and a SMALL amount of good quality grease applied to partially fill the spaces between the rollers.

1liliIS InSI

always list

I No. Descriptio" Req'd.

3 4397 4 4282 5 4874 2

6 4365 2 7 4870 6 Rod Mt'g. S 909848·6 9 5197

10 5-50.75 Ring Ext. Truarc

S·52·6 Pin

12

LITHO IN U. A.