Upload
lehanh
View
226
Download
4
Embed Size (px)
Citation preview
This product is intended to be installed and serviced by a qualied licensed electrician. Install in accordance with the National Electric Code, and local regulations. Only power with a regulated (listed) constant voltage Class 2 power supply (12-24V DC).
Ensure applicable wire is installed between driver, xture, and any controls in between. When choosing wire, factor in voltage drop, amperage rating and type (in-wall rated, wet location rated, etc.). Inadequate wire installation could overheat wires and cause re.
This product is rated for indoor installation and only for dry locations.
Do not modify this product beyond the instructions in this guide or the warranty will be voided.Wiring diagrams in this installation guide for basic installations. Please carefully review your installation before proceeding
Safety & Warnings
Before you begin, read all warnings and installation instructions.
1. Product Parameter:
WiFi-104 is a versatile RGB color control lighting system. Through WiFi function and mobile devices, the wi-104 can control various types of RGB LED lighting products VIA iOS or Android.
WiFi-104 lighting control system integrates four functional controls including; dimming, color temperature adjusting, RGB and RGBW (that can be set as single color temperature). The 104 can control up to 12 zones areas using the optional wireless R4-5A Zone Receiving controller.
Communication Standard
Input Voltage
Max Current Load
Max Output Power
Product Size
Weight(G.W.)
Wi-Fi, 802.11 b/g/n Protocol
DC12V~DC24V (Use only with Class 2 listed regulated power supply)
4A x4CH Max
192W/384W (12V/24V)
L128 × W73 × H45 mm
290g
WiFi-104 control system supports direct connection or by router:In directly connection, mobile phone, IOS and Android can directly control the WiFi-104 controller + R4-5A/R4-CC wireless control, without any third party of network equipment. Included is a 2.4G RF remote (M12) if software is not used.
WiFi Control Distance
Working Temperature
Package Size
100m (Distance of cross-eyed)
-20°C ~ 40°C
WiFi-104 Controller
L135 x W80 x H64mm
WiFi-104 WiFi Lighting Control System
1LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA
Copyright @2014 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
WiFi-104 Wi-Controller
2. Conguration Diagram
www.ledworldlighting.com
Working Voltage
Transmitting Frequency
Remote Distance
Dimensions
Weight(G.W.)
DC3V (CR2032 button battery)
2.4GHz
30m (Distance of cross-eyed)
L 104 × W 60 × H 9 mm
290g
M12 Remote Control
127.6mm
73mm
RUN
RX/TX
LINK
EXT KEY
SSID
MATCHSCENE
Power Input / LED Output Learning ID Key
SceneIndicators
44.5mm
3. Controller Operating Instructions
RUN
RX/TX
LINK
EXT KEY
SSID
MATCH
FUN
ANTENNA installation instruction
1). Install / Uninstall ANTENNARotate Antenna clockwise to install. To uninstall rotate Antenna anti-clockwise
2). Light Indicator InstructionsŸ RUN : It ashes quickly about 25s during the electric
initialization. Flashes once per second after initialization
Ÿ LINK: It keeps on when the mobile device connected with WiFi controller, and turns off when disconnected
R4-5A Constant Voltage Zone Receiver
Wireless Frequency
Input Voltage
Max Output Power
Remote Distance
2.4GHz
DC5V~DC24V
5A × 4CH Max 20A
100W/240W (12V/24V)
50m (Distance of cross-eyed)
Max Current Load
Working Temperature
Product Size
Weight(G.W.)
-20°C ~ 40°C
L 175 × W 44 × H 30 mm
110g
ManufacturerInterface
SSID CodeSwitch
2LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA
Copyright @2014 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
WiFi-104 Wi-Controller
4. ios/Android application instructions:
1). Download Application:
www.ledworldlighting.com
Channel Color
RUN
RX/TX
LINK
EXT KEY
SSID
MATCH
SCENE
54 63 72 81 90 AF BE CD
3). SSID Number SettingSet the controller's SSID number with code switch, SSID number range from WiFi-104-SSID-0 to WiFi-104-SSID-F. which means our product could set 16 isolated LAN in the same area. The controller will re-enter initialization status once the code switch changes. RUN indicator light will ash quickly about 25 seconds, mobile device need to search and connect WiFi again after Initialization nished.
4). MATCH Key and SCENE KeyShort press MATCH key and WiFi controller will begin its learning ID status for the standard M12 remote. Short press SCENE key sequentially to the user-saved scene modes, 4 scene total.
Restore factory settings/Delete passwordLong press MATCH key and SCENE key simultaneously more than 2 seconds, the mach ine w i l l back to the defau l t parameter, including the parameters of changing modes, zones, group parameters
Scene Interface
RUN
RX/TX
LINK
EXT KEY
SSID
MATCH
SCENE
SCENE
SCENE Key and MATCH Key
Scene Save
Scene 2
Scene 3
Scene 4
Back
Scene 1
MATCH
14:17 PM 100%
and network parameters. In default parameters: Only the 1st zone is present, default RGBW mode, the changing mode is RGB skipping, the brightest is white, no groups, network SSID is WiFi-104-SSID-X (X is the actual coding switch corresponding SSID values), WiFi-104 controller restore as directly connect and the connection password is blank.
scan to download android appscan to download ios app
Available on the
App StoreANDROID APP ON
Google play
2). How to operate the Application:A). Network connection setting :WiFi-104 support 2 connection modes: Directly connection as router or connect by additional router.
Ÿ Connecting WiFi controller as a routerGo to mobile device's WiFi setting, Search the available WiFi Network. From the list select WiFi Network, appended with SSID-Number.(As Legend-1), (no password is set by default).
Apple WiFi connectionAndroid WiFi connection
WLAN settings
WLAN
Connect to WiFi-104-SSID-0
Network notification
Auto Connect
WiFi-104-SSID-0
TP-008
ACW1F
Notify me when an open network is
available
set the way of network’s connection
Connected
Remembered, secured with WPA/
WPA2 PSK
Remembered
WLAN networks
16:0714:17 PM
Wi-FiSettings
Wi-Fi
Other...
Ask to jin Networks
Known networks will be joined automatically.if no known networks are available, you willhave to manually select a network.
CHOOSE A NETWORK...
WiFi-104-SSID-0
WiFi-104-SSID-1
100%
(Legend-1)
3LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA
Copyright @2014 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
www.ledworldlighting.com
Ÿ Connect WiFi-104 with a additional router:
a). Connect to the WiFi-104 controller, as same procedure as (A)b). Click WiFi-104 application icon to start the app. The app will search and list the working WiFi controller automatically
WiFi-104 Wi-Controller
1Network
ZoneWiFi-104-SSID-2
32:AA:3C:7E:B4:DBDisconnected
2
Device List
2 3 4
5 6 7
1
8
10 11 129
WiFi-104-SSID-0
32:AA:3C:7E:B4:DA
Network
Zone
Connect to WiFi-104-SSID-1
(Legend 2-1) ( -2-2)
1Network
ZoneWiFi-104-SSID-1
32:AA:3C:7E:B4:DBConnect to TP-LINK1
2
Device List
2 3 4
5 6 7
1
8
10 11 129
WiFi-104-SSID-0
32:AA:3C:7E:B4:DA
Network
Zone
Connect to TP-LINK1
1Network
ZoneWiFi-104-SSID-2
32:AA:3C:7E:B4:DDConnect to TP-LINK1
Connected with additional routerConnected with WiFi-104 as a router
Delete WiFi-104 controller list
Disconnected WiFi-104 controller
Network interface Zone function interface Change the interface background Connected Router Name
Connected WiFi-104
search button for the WiFi-104 controller
Active WiFi-104
Workable zone NO
14:17 PM 100% 14:17 PM 100%
(Legend 2-2)
c). Click “Network” key to enter Network interface(as legend-3-1). Turn ON "connect to existing LAN" option and app will search the available WiFi SSID list. Choose the available router to connect (Note : Do not choose WiFi-104 controller)(as legend-3-2 )
Repeat the a-b-c steps if you are connecting multiple WiFi-104 controller to same wireless router.
d). Exit WiFi-104 application, go to mobile wireless network setting, choose the wireless router to connect. Start WiFi-104 application again, device will list interface as legend-2-2. Complete the same steps to connect to the additional router.
NetworkBack
User setting
Wireless mode
Connect to existing LAN
Change SSID and password
NetworkBack
Available wireless LAN networks
TP-LINK1
WiFi-104-SSID-0
WiFi 104 SSID 1- - -
User setting
Wireless mode
Connect to existing LAN
Change SSID and password
WiFi-104-SSID-2
WiFi-104-SSID-3
WiFi-104-SSID-4
(Legend 3-1)
Network interface
(Legend 3-2)
14:17 PM 100% 14:17 PM 100%
Note: In this connection mode, to avoid the mobile device automatically connect to WiFi-104 after the setting has completed, please click “workable WiFi-104". On dialog box click "Forget this network" or "Cancel save".
WLAN settings
WLAN
Connect to WiFi-104-SSID-0
Network notification
Auto Connect
WiFi-104-SSID-0
TP-008
ACW1F
Notify me when an open network is
available
set the way of network’s connection
Connected
Remembered, secured with WPA/
WPA2 PSK
Remembered
WLAN networks
16:07
WiFi-104-SSID-0
Cancel Forget Disconnect
StatusConnected
Signal strengthExcellent
Link speed65Mbps
SecurityOpen
IP address10.10.100.103
14:17 PM
WiFi-104-SSID-0Wi-Fi
Forget this Netnwork
IP ADDRESS
100%
DHCP BootP Static
IP Address
Subnet Mask
Router
DNS
Search Domains
10.10.100.103
255.255.255.0
10.10.100.254
10.10.100.254
Hi_flying
Cancel saved WiFi-104 connection information
4LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA
Copyright @2014 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
www.ledworldlighting.com WiFi-104 Wi-Controller
B). Main interface ( 5 types total)
G 255R 255 B 255 W 255
W80% 80%
NameLong press to turn off single zone or group
ModeDevice SceneGroup On/off
2 3 4 5 6
7 8
RGBW
1RGB CT1 RGB
RGBW
10 11 129RGBW DIM
Group1 Group2 Group3
DIM
DIM RGBW RGBW
CT2
RGBW Value
5 Main interfaces
White ValueBrightness Value
Color Bar
Zone Selection
Group Interface Mode Interface Scene Interface
Main Switch
Group Selection
Device List Interface
14:17 PM 100%
NameLong press to turn off single zone or group
ModeDevice SceneGroup On/off
2 3 4 5 6
7 8
RGBW
1RGB CT1 RGB
RGBW
10 11 129RGBW DIM
Group1 Group2 Group3
DIM
DIM RGBW RGBW
100%
W 255
CT2
14:17 PM 100%
40%
WW 135120 NW
NameLong press to turn off single zone or group
ModeDevice SceneGroup On/off
2 3 4 5 6
7 8
RGBW
1RGB CT1 RGB
RGBW
10 11 129RGBW DIM
Group1 Group2 Group3
DIM
DIM RGBW RGBW
CT2
14:17 PM 100%
40%
WW 15 NW 240 CW 0
NameLong press to turn off single zone or group
ModeDevice SceneGroup On/off
2 3 4 5 6
7 8
RGBW
1RGB CT1 RGB
RGBW
10 11 129RGBW DIM
Group1 Group2 Group3
DIM
DIM RGBW RGBW
CT2
14:17 PM 100%
G 255R 255 B 255
40%
NameLong press to turn off single zone or group
ModeDevice SceneGroup On/off
2 3 4 5 6
7 8
RGBW
1RGB CT1 RGB
RGBW
10 11 129RGBW DIM
Group1 Group2 Group3
DIM
DIM RGBW RGBW
CT2
14:17 PM 100%
G 255R 255 B 255 W 255
W80% 80%
NameLong press to turn off single zone or group
ModeDevice SceneGroup On/off
2 3 4 5 6
7 8
RGBW
1RGB CT1 RGB
RGBW
10 11 129RGBW DIM
Group1 Group2 Group3
DIM
DIM RGBW RGBW
CT2
14:17 PM 100%
C). The learning method of Zone control
Ÿ Turn on zone controlClick “Zone” on the Device list, Enter Zone set interface. According to the lighting control requirements, turn on multiple zone, select the light type and naming zone.Note : Default WiFi-104 controller works as NO.1 zone, which can select if to connect lights. If not, sub-control can be replaced as the rst zone.
ZONE NAME LINK
Zone Set
TYPE
Back
CONTROLLER1 DIM1
CONTROLLER2
CONTROLLER3
CONTROLLER4
CONTROLLER5
CONTROLLER6
CONTROLLER7
CONTROLLER8
CONTROLLER9
CONTROLLER10
CONTROLLER11
CONTROLLER12
Ct1
Ct2
RGB
RGBW
RGBW
RGBW
RGBW
RGBW
RGBW
RGBW
NONE
2
3
4
5
6
7
8
9
10
11
12
ZONE NAME LINK
Zone Set
TYPE
Back
CONTROLLER1 DIM1
CONTROLLER2
CONTROLLER3
CONTROLLER4
CONTROLLER5
CONTROLLER6
CONTROLLER7
CONTROLLER8
CONTROLLER9
CONTROLLER10
CONTROLLER11
CONTROLLER12
Ct1
Ct2
RGB
RGBW
RGBW
RGBW
RGBW
RGBW
RGBW
RGBW
NONE
2
3
4
5
6
7
8
9
10
11
12
9
10
11
12
13
14
15
Select type
Cancel
DIM
CT1
CT2
RGB
RGBW
Device List
2 3 4
5 6 7
1
8
10 11 129
WiFi-104-SSID-0
32:AA:3C:7E:B4:DA
Network
Zone
Connect to WiFi-104-SSID-1
Zone
Return
Type
Turn on
Turn off
Zone Set InterfaceDevice List Interface Select Type Interface
Zone name
Zone number
14:17 PM 100% 14:17 PM 100% 14:17 PM 100%
Ÿ Learning IDShort press "ID learning button" on the receiver, the running light go ash to keeps on. Then select the zone number on the software interface and touch the color bar for 2-3 seconds. Long buzzer means (meantime the running light returns to ash), zone control and master control matched
G 152R 87 B 255 W 255
W80% 80%
NameLong press to turn off single zone or group
ModeDevice SceneGroup On/off
2 3 4 5 6
7 8
RGBW
1RGB CT1 RGB
RGBW
10 11 129RGBW DIM
Group1 Group2 Group3
DIM
DIM RGBW RGBW
CT2
14:17 PM 100%
2
3
Zone number
Color Bar1
ID learning button
Ÿ Cancelling IDLong press” ID learning button” for 5 seconds, If success, Buzzer will sound long and louder
5LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA
Copyright @2014 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
www.ledworldlighting.com WiFi-104 Wi-Controller
D). Group
Ÿ Group can control several zones at the same time, and several zones can adjust color, color temperature and brightness together.
Ÿ You can set upto 3 groups, all zones at the same groups must be the same type, and one zone can belong to multiple groups simultaneously.
Ÿ Select the group, then the corresponding group will appear in the main interfaceŸ It will automatically cancel the relevant zone group settings as you changed the type or set up
enabled status of the zone at the Zone Set interface.
GroupsBack
1RGB
2 3 4RGBW CT1
5
9
DIM
RGBW
6
10
7
11
8
12
RGB
RGBW
DIM
RGBW
RGBW
DIM
Group1 Group2 Group3
Only the same type of zone can group
Group name Ent group name
Use this group
CT2
Group Selection
Group Name
Open the Group
Group Interface
Zone Selection
Group operations in main interface
G 255R 255 B 255 W 255
W80% 80%
NameLong press to turn off single zone or group
ModeDevice SceneGroup On/off
2 3 4 5 6
7 8
RGBW
1RGB CT1 RGB
RGBW
10 11 129RGBW DIM
Group1 Group2 Group3
DIM
DIM RGBW RGBW
CT2
14:17 PM 100%14:17 PM 100%
E). Mode Interface for RGB / RGBW Type
ModeBack
Long press can choose to change the current pattern types
CustomDefault
2
4
40%
Set Play
2 3Strobe
1Jump
4Fadein dimming
6Gradual
7Strobe
5Jump
8Fadein dimming
Gradual
10Gradual
11Strobe
9Jump
12Fadein dimming
Combined cycle set to play
Cancel
2Gradual
3Strobe
1Jump
4
6Gradual
7Strobe
5Jump
8
10Gradual
11Strobe
9Jump
12
Fadein dimming
Fadein dimming
Fadein dimming
OK
ModeBack
Long press can choose to change the current pattern types
CustomDefault
2
4
40%
Set Play
2 3Strobe
1Jump
4Fadein dimming
6Gradual
7Strobe
5Jump
8Fadein dimming
Gradual
10Gradual
11Strobe
9Jump
12Fadein dimming
ModeBack
2Gradual
3Strobe
Long press can choose to change the current pattern types
CustomDefault
4
40%
W 40%
1Jump
4Slowly fade
The current selected color combination
6Gradual
7Strobe
5Jump
8Slowly fade
10Gradual
11Strobe
9Jump
12Slowly fade
2 Select Style
Cancel
Jump
Gradual
Strobe
Fadein dimming
ModeBack
Long press can choose to change the current pattern types
CustomDefault
2
4
40%
Set Play
2 3Strobe
1Jump
4Fadein dimming
6Gradual
7Strobe
5Jump
8Fadein dimming
Gradual
10Gradual
11Strobe
9Jump
12Fadein dimming
Changing mode
preset changing mode
Speed Adjustment
Mode Interface
Brightness Adjustment
Play in a loop Select the type of changing effect (skipping/ash/smooth/fade)
14:17 PM 100% 14:17 PM 100% 14:17 PM 100% 14:17 PM 100%
F). DIY Interface
ModeBack
Long press can choose to change the current pattern types
CustomDefault
2
4
40%
Set Play
2 3Strobe
1Jump
4Fadein dimming
6Gradual
7Strobe
5Jump
8Fadein dimming
Gradual
10Gradual
11Strobe
9Jump
12Fadein dimming
Edit Back Apply
Select Color
Color Edit
Long press to delete single color
G 255R 0 B 0
current color combination
Back Apply
Select Color
Color Edit
Long press to delete single color
G 255R 255 B 255
current color combination
Edit DIY Mode
DIY mode
Play single DIY Mode
Playback Loop several DIY mode
DIY Mode interface
Save DIY
Color Frame
Edit single DIY Mode Edit single DIY Mode
14:17 PM 100% 14:17 PM 100% 14:17 PM 100%
G). Scene Interface
Scene
Scene 2
Scene 4
Back
Save
Play
Save
Play
Scene 3
Save
Play
Save
Scene 1Save
Play
Scene
Scene 2
Scene 4
Back
Save
Play
Save
Play
Scene 3
Save
Play
Save
Scene 1Save
Play
Scene
Scene 2
Scene 3
Scene 4
Back
Scene 1
Cancel OK
Scene name
Scene1Photo Setting
Cancel
Use Camera
Photo Library
Remove Photo
Scene Background
Click to change background
Play the scenes
Play the scenes
Saving the current scene
Change the scene background Save scene interface
14:17 PM 100% 14:17 PM 100% 14:17 PM 100%
LongPress
ShortPress
combine changing mode
Long press color mode to delete
6LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA
Copyright @2014 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
www.ledworldlighting.com WiFi-104 Wi-Controller
5. WiFi Network SSID Name and Password Setting
In Device list interface, click “Network key” to enter Network interface, select “Change SSID and Password” (Click” ” ) to enter User Setting. Type new SSID name and password . (Min: 8 Characters, consist of 0-9, a-z and A-Z). Click “Apply” button to save the changes.
NetworkBack
User setting
Wireless mode
Connect to existing LAN
Change SSID and password
14:17 PM 100%
User Setting
SSID
Password
WiFi-104-SSID-0
Ent the new Password
Back
Restore factory settings
Change the SSID name and password Apply
14:17 PM 100%
User Setting
Accoun
Change the account name and password
SSID
Password
Ltech-WiFi-104-0
Ent the new Password
Admin
Password
Restore factory settings
Change the SSID name and password
Cancel OK
Change the SSID password
Ent the NEW Password
Ent the NEW Password again
Back
14:17 PM 100%
Device List
2 3 4
5 6 7
1
8
10 11 129
WiFi-104-SSID-0
32:AA:3C:7E:B4:DA
Network
Zone
Connect to WiFi-104-SSID-1
14:17 PM 100%
1.Device Lists 2.Network interface 3.Change SSID name interface 4.Change SSID password
Note: In connection with WiFi-104 as a router, please exit software after changed the SSID name and the password, then enter the mobile device system setting to reconnect the WiFi-104. In additional wireless router connection, click in Device List interface to search again the WiFi-104 controller after SSID name change.
Note: If you forget the WiFi network password, please simultaneously press : and more than 2s to restore the factory default settings, It will wipe-out WiFi network password (More details on page 3 [Restore factory settings/Delete password]
SCENEMATCH
6. Remote operating Instructions
Learning IDShort press learning key in WiFi-104 controller. Long buzzer will sound, then press any keys on M12 remote, Long buzzer will sound again.
MATCH
Cancel IDLong press learning key in WiFi-104 controller for more than 6s, long buzzer will sound. Which will cancel ID (cancel all learned remotes with WiFi-104 ).
MATCH
Turn on zone
Short press to play scene
Long press to save scene
synchronization for 12 zones
Turn off zone
Short press to turn off all zones
Short press to turn on all zones
Long press to turn on the key tone
Long press to turn off keyt one
( Long press to decrease brightness, under the mode of dimming or color temperature)
( Long press to increase brightness, under the mode of dimming or color temperature)
7. Wiring Diagram
1). Connect to the zones controller and LED Lights (the same way of WiFi-104 connection)Note : WiFi-104 default to rst zone, Master controller can choose whether connecting to LED Lights or not. If not, use wireless control to instead of the rst zone.Multiple partitions can be set to the same type or several types, such as all partitions are single color, can be set to DIM dimmer light type, such as dimmer, color temperature, RGB, and other types of lamps, different partition set to different types of lamps, the lamps connection diagram as follows:
7LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA
Copyright @2014 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
8
www.ledworldlighting.com WiFi-104 Wi-Controller
DC5V-24V
+
B
R
G
+
B
R
G
511
511
331
511
511
331 331
511
511
331
511
511
331 331
+
B
R
G
+
B
R
G Zone 4
DC5V-24V
121
121
121
121
121
121
121
121
121
121
121
121
121
121
ww
w 121
121cw Zone 3
DC5V-24V
121
121
121
121
121
121
121
121
121
121
121
121
121
121
ww
w
121
121 Zone 2
DC5V-24V
RU
N
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
Zone 1
DC5V-24V
+
B
R
G
W
+
B
R
G
W
+
B
R
G
W
+
B
R
G
W
Zone 5
Single color strip
Nature white/Warm white strip
Nature white + Warm white + Cold white strip
RGB strip
RGBW strip
M12WiFi -104
G 255R 255 B 255 W 255
W80% 80%
CONTROLLER1Long press to turn off single zone or group
ModeDevice SceneGroup On/off
2 3 4 5 6
7 8
RGBW
1RGB CT1 RGB
RGBW
10 11 129RGBW DIM
Group1 Group2 Group3
DIM
DIM RGBW RGBW
CT2
Mobile phone
DIM
CT
CCT
RGB
RGBW
RU
NR
UN
RU
NR
UN
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA
Copyright @2014 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
Warning: Input voltage must be identical to output voltage of the LED Fixture!
Exposed wire should not be more than 6- 8 mm long & solder tip (tinned). Do not allow Wires to cross and insure all exposed wire is fully inserted into the screw terminals. Hand tighten screw terminals. Use 22 to 16 AWG gauge wire for output terminals.
WIRE 6-8 MM (0.25-0.30")
www.ledworldlighting.com WiFi-104 Wi-Controller
3). Connect by a router
(Max 12 Zones)
R4-5A
R4-5A
R4-5 A
R4-5A
R4-5AR4-5A
R4-5A
R4-5A
R4-5A
R4-5A
R4-5A
zone 3
zon
e 4
zo
ne 5
zone 6
zone 7zone 8
zone
9
zo
ne 1
0zon
e 1
1
zone 12
zone 2
zone 1
(Max 12 Zones)
R4-5A
R4-5A
R4-5A
R4-5A
R4-5AR4-5A
R4-5A
R4-5A
R4-5A
R4-5A
R4-5A
zone 3
zo
ne 4
zo
ne 5
zone 6
zone 7zone 8
zone
9
zo
ne 1
0zon
e 1
1
zone 12
zone 2
zone 1
Multiple zone receiver R4-5A can be installed for each zone within effective range
A B
A B
Wireless Router
9LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA
Copyright @2014 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
2). Direct connection of WiFi-104 as router
(Max 12 Zones)
R4-5A
R4- 5A
R4-5A
R4-5A
R4-5AR4-5A
R4-5A
R4-5A
R4- 5A
R4-5A
R 4-5A
zone 3
zon
e 4
zo
ne
5
zone 6
zone 7zone 8
zone 9
zon
e 1
0zo
ne
11
zone 12
zone 2
zone 1
www.ledworldlighting.com WiFi-104 Wi-Controller
8. Limited Warranty
We provide lifelong technical assistance with this product
A 1-year Limited factory warranty from the date of purchase. The warranty is for free repair or replacement and covers manufacturing faults only.
10LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA
Copyright @2014 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
4). Remote Distance Reference
Note: The following distance is measured at distance open environment, in an open environment testing wireless distance will be reduced, please refer to our actual test distance before installation.
WiFi-104
Master controller
R4-5A/R4-CC
Slave controller
M12 Remote
50m
30m
100m100m
Mobile phone Router