18
Woodwork Tools 2 Quiz

Woodwork Tools 2 Quiz

  • Upload
    tosca

  • View
    73

  • Download
    0

Embed Size (px)

DESCRIPTION

Woodwork Tools 2 Quiz. 1.What is the correct name for this tool?. Depth Gauge. Cutting Gauge. Mortise Gauge. Marking Gauge. 2. Which of the following tools would be used to rip a standard sheet of 9mm Plywood in half?. A Coping Saw. A Tenon Saw. A Jnr Hacksaw. A Panel Saw. - PowerPoint PPT Presentation

Citation preview

Page 1: Woodwork Tools 2 Quiz

Woodwork Tools 2 Quiz

Page 2: Woodwork Tools 2 Quiz

Marking Gauge

Mortise Gauge

Cutting Gauge

1.What is the correct name for this tool?

Depth Gauge

Page 3: Woodwork Tools 2 Quiz

2. Which of the following tools would be used to rip a standard sheet of 9mm Plywood in half?

A Panel Saw

A Coping Saw A Tenon Saw

A Jnr Hacksaw

Page 4: Woodwork Tools 2 Quiz

3. What is the correct name for this saw?

Pad Saw

Flush Cut Saw

Bow Saw

Dovetail Saw

Page 5: Woodwork Tools 2 Quiz

Pliers

Pincers

Engineers Pliers

4.What is the correct name for this tool?

End Cutters

Page 6: Woodwork Tools 2 Quiz

Through Housing Joint

Mortise & Tenon Joint

Cross Halving Joint

5.Which joint is this tool normally used to mark out?

Rebate Joint

Dovetail Joint

Stopped Housing Joint

Page 7: Woodwork Tools 2 Quiz

Adjustable Square

Sliding Bevel

Cutting Gauge

6.What is the correct name for this tool?

Mitre Gauge

Page 8: Woodwork Tools 2 Quiz

Roll the pincers as shown

7. Which picture shows the correct way to use these pincers ?

Pull the pincers as shown

Page 9: Woodwork Tools 2 Quiz

8. Which of the following tools would be used to start a small hole for a screw?

A Scriber

A Countersink Drill

A Nail Punch

A Bradawl

Page 10: Woodwork Tools 2 Quiz

9. What is the blade of a Panel saw made from?

Cart Iron

Spring Tempered Tool Steel

Bright Drawn Mild Steel (BDMS)

Stainless Steel

Page 11: Woodwork Tools 2 Quiz

10. What is the correct name for the tool being used in this picture?

Mortise Gauge

Cabinet Scraper

Sliding Bevel

Cutting Gauge

Router

Page 12: Woodwork Tools 2 Quiz

11. What is the correct name for the tools shown below?

Centre Punch

Parallel Punch

Nail Punch

Dot Punch

Hollow point

Page 13: Woodwork Tools 2 Quiz

Stock

Spur

Stem

12.What is the correct name for this part of a Mortise Gauge?

Thumbscrew

Page 14: Woodwork Tools 2 Quiz

13. Which of the following tools would be used for marking out angles other than 90˚

Odd Leg Callipers

A Try Square An Engineers Square

A Sliding Bevel

Page 15: Woodwork Tools 2 Quiz

Drawing lines parallel to an edge

Marking out Circles Centre Punching Holes

14. What are Trammels normally used for?

Marking out Mortise Joints

Page 16: Woodwork Tools 2 Quiz

Dovetail Saw

Fret Saw

15. What is the correct name for this tool?

Bow Saw

Flush Cut Saw

Piercing Saw

Coping Saw

Panel Saw

Page 17: Woodwork Tools 2 Quiz

Well Done

Quiz Completed

Page 18: Woodwork Tools 2 Quiz

Wrong

Click here to try again