TM

Woven Mono"lament Geotextiles

Thrace-LINQ™ offers a wide range of monofilament woven

fabrics, for use in critical civil engineering applications.

Woven monofilament geotextiles are manufactured from

extruded polypropylene to create a very dimensionally stable,

highly permeable geotextile. Monofilaments have superior

resistance to soil and biological clogging, providing proven

erosion control along highway and waterway embankments.

Stability and strength, coupled with clog-resistant, high-flow

properties, make this fabric ideal for use under hard armor

systems. As separators and stabilizers, monofilaments allow

water to pass freely, while preventing contamination of base

material and adding tensile elements to soil and fill material.

Our monofilaments meet AASHTO M288 strength guidelines,

as well as many state DOT specifications.

If erosion control, filtration and drainage are you concerns,

Thrace has the fabric for your site-specific needs. Call us today

for your woven fabric needs.

The Foundation to Build On™ Excellent products to do the job.

The service to do it right.™

• High modulus fabric, resistant to installation damage

• Chemical resistant polypropylene fabric construction

• Provide separation and drainage, while reinforcing

• Promote filter formation, while inhibiting soil migration

• Superior clog resistant monofilament construction

• Available in various widths from 15’ to 6'

Features & Benefits

Monofilaments

Erosion Control SeparationFiltrationReinforcement/

Stabilization

GTF GTF GTF GTF

400EO 400E 404 117F

AASHTO AASHTO

lbs 370 / 220 370 / 250 400 / 315 350 / 225

(N) (1646 / 979) (1646 / 1112) (1779 / 1401) (1557 / 1001)

lbs/ft 2400 / 1740 2700 / 1740 3000 / 2760 N/A

(kN/m) (35 / 25) (39 / 25) (44 / 40) (N/A)

WW Elongation D4632 % 19.0 / 7.0 17.0 / 15.0 12.0 / 8.0 N/A

lbs 115 / 75 100 / 60 150 / 165 110 / 75

(N) (512 / 334) (445 / 267) (667 / 734) (489 / 334)

lbs 675 950 1150 1000

(N) (3003) (4226) (5115) (4448)

UV Stability D4355 % @ 500 hrs 90 90 90 90

Permittivity D4491 sec-1 2.100 0.280 0.900 1.500

gpm/ft2 145 18 70 200

(l/min/m2) (5908) (733) (2852) (8149)

US Sieve 40 70 40 20

(mm) (0.425) (0.212) (0.425) (0.850)

Percent Open Area

CW02215% 10 4 to 6 1 20

ft 12.5 12 15 12

(m) (3.8) (3.7) (4.6) (3.7)

ft 300 300 300 300

(m) (91.4) (91.4) (91.4) (91.4)

yd2 416 400 500 400

(m2) (348) (334) (418) (334)

lbs 190 193 310 153

(kg) (86) (88) (141) (69)

2 Minimum Average Roll Value. All values are MARV unless otherwise noted.

3 AOS values are reported as Maximum Average Roll Value.

4 Other products and roll sizes may be available.

Roll lengths, areas, and weights may vary.T Typical roll properties.

Mullen Burst ASTM D3786 and Puncture D4833 have been removed.

Neither test method is recognized by AASHTO M288.

CBR puncture D6241 has replaced D4833, under AASHTO M288.

Mullen Burst is not recognized by D35 committee on Geosynthetics.

2550 West Fifth North St. ● Summerville, SC 29483

800.445.4675 ● 843.873.5800 ● Fax: 843.875.8276

www.thracelinq.com ● geo@thracelinq.com

D4632

D4595

Woven Polypropylene

MECHANICAL PROPERTIES2

Monofilament

The property values listed above are effective 09/2012 and are subject to change without notice.

Grab Tensile Strength

Wide Width Tensile

ULT

Trapezoid Tear

WaterFlow Rate

Apparent Opening

Size (AOS3 )

D4491

Roll Weight (est.)

Roll Length

Roll Width

Roll Area

CBR Puncture D6241

HYDRAULIC PROPERTIES2

Packaging4,T

ENDURANCE PROPERTIES2

D4533

PropertiesASTM

TESTUNIT

D4751

1 Contact your Thrace-LINQ distributor or representative for technical assistance and for products meeting AASHTO M288 specifications.

Additional information can also be found at www.thracelinq.com. Methods and values may change without notice.