Feel the differenceFordMondeoOwner's handbook
The information contained in this publication was correct at the time of going to print. In theinterest of development the right is reserved to change specifications, design or equipmentat any time without notice and without incurring any obligations. This publication, or partthereof, may not be reproduced nor translated without our approval. Errors and omissionsexcepted.
Ford Motor Company 2007
All rights reserved.
Part number: 8S7J-19A321-DA (CG3536en) 06/2007 20070727130405
IntroductionAbout this handbook........................7Symbols glossary..............................7Parts and accessories......................7
Quick startQuick start.........................................10
Child safetyChild seats........................................19Booster cushions............................20Child seat positioning.....................22ISOFIX anchor points......................25Child safety locks............................27
Occupant protectionPrinciple of operation.....................28Fastening the seat belts.................31Seat belt height adjustment...........31Seat belt reminder...........................31Using seat belts during
pregnancy....................................32Disabling the passenger
airbag............................................32
Keys and remotecontrols
Using the key...................................34General information on radio
frequencies..................................34Programming the remote
control...........................................34Changing the remote control
battery...........................................34
LocksLocking and unlocking...................36Global opening and closing...........38Keyless entry...................................40
Engine immobiliserPrinciple of operation.....................44Coded keys.....................................44Arming the engine immobiliser.....44Disarming the engine
immobiliser...................................44
AlarmPrinciple of operation.....................45Arming the alarm.............................47Disarming the alarm........................47
Steering wheelAdjusting the steering wheel.........49Audio control...................................49
Wipers and washersWindscreen wipers..........................51Autowipers........................................51Windscreen washers.....................52Rear window wiper and
washers........................................52Headlamp washers........................53Checking the wiper blades...........53Changing the wiper blades...........53
LightingLighting control................................56Autolamps........................................57Front fog lamps...............................57
1
Table of contents
Rear fog lamps................................57Headlamp levelling..........................58Hazard warning flashers................59Adaptive front lighting system
(AFS)..............................................59Direction indicators..........................61Interior lamps....................................61Removing a headlamp...................62Changing a bulb..............................63Bulb specification chart...................71
Windows and mirrorsElectric windows.............................73Exterior mirrors................................75Electric exterior mirrors..................76Interior mirror....................................77Auto-dimming mirror......................78
InstrumentsGauges.............................................79Warning lamps and indicators.......81Audible warnings and
indicators......................................84
Information displaysGeneral information........................85Trip computer..................................94Personalised settings.....................96Information messages...................99
Climate controlPrinciple of operation....................109Air vents..........................................109Manual climate control..................110Automatic climate control.............113
Heated windows and mirrors......116Auxiliary heater...............................116Electric sunroof..............................120
SeatsSitting in the correct position.......124Manual seats..................................124Electric seats..................................125Head restraints...............................127Rear seats.......................................127Heated seats.................................128Ventilated seats.............................129
Convenience featuresSun blinds.......................................130Instrument lighting dimmer..........130Clock...............................................130Cigar lighter....................................130Ashtray.............................................131Auxiliary power sockets................131Cup holders....................................132Glove box.......................................132Storage compartments...............132Map pockets..................................133Memory function...........................133Glasses holder...............................135Auxiliary input (AUX IN) socket.....135
Starting the engineGeneral information......................136Ignition switch................................136Keyless starting.............................136Steering wheel lock.......................138Starting a petrol engine................139Starting a diesel engine................140
2
Table of contents
Diesel particulate filter (DPF)........140Switching off the engine...............141
Fuel and refuellingSafety precautions........................142Fuel quality - Petrol........................142Fuel quality - Diesel.......................142Catalytic converter........................142Fuel filler flap...................................143Refuelling........................................144Fuel consumption.........................144Technical specifications................144
TransmissionManual transmission.....................147Automatic transmission................148
BrakesPrinciple of operation.....................151Hints on driving with ABS..............151Parking brake.................................152
Stability controlPrinciple of operation....................153Using stability control....................153
Hill launch assist(HLA)
Principle of operation....................155Using HLA.......................................155
Active suspensionPrinciple of operation....................158Using active suspension..............158
Parking aidPrinciple of operation....................159Using the parking aid....................159
Cruise controlPrinciple of operation.....................161Using cruise control.......................161
Adaptive cruise control(ACC)
Principle of operation....................163Using ACC......................................165Forward alert function..................168
Load carryingGeneral information.......................170Luggage anchor points................170Sliding loadspace floor..................170Rear under floor storage..............172Cargo nets......................................173Luggage covers.............................174Roof racks and load carriers........174Dog guard.......................................174Load retaining fixtures..................176
TowingTowing a trailer...............................179Detachable tow ball.......................179
Driving hintsRunning-in......................................183
Emergencyequipment
First aid kit.......................................184
3
Table of contents
Warning triangle.............................184
Status after acollision
Inspecting safety systemcomponents...............................186
FusesFuse box locations........................187Changing a fuse............................189Fuse specification chart...............190
Vehicle recoveryTowing points................................200Towing the vehicle on four
wheels.........................................201
MaintenanceGeneral information.....................202Opening and closing the
bonnet........................................203Engine compartment overview -
1.6L Duratec-16V Ti-VCT(Sigma).......................................204
Engine compartment overview -2.0L Duratec-HE (MI4).............205
Engine compartment overview -2.3L Duratec-HE (MI4).............206
Engine compartment overview -2.5L Duratec-ST (VI5)...............207
Engine compartment overview -1.8L Duratorq-TDCi (Kent)Diesel..........................................209
Engine compartment overview -2.0L Duratorq-TDCi (DW)Diesel...........................................210
Engine compartment overview -2.2L Duratorq-TDCi (DW)Diesel............................................211
Engine oil dipstick - 1.6LDuratec-16V Ti-VCT (Sigma).....212
Engine oil dipstick - 2.0LDuratec-HE (MI4)/2.3LDuratec-HE (MI4).......................212
Engine oil dipstick - 2.5LDuratec-ST (VI5)........................213
Engine oil dipstick - 1.8LDuratorq-TDCi (Kent) Diesel.....213
Engine oil dipstick - 2.0LDuratorq-TDCi (DW) Diesel/2.2LDuratorq-TDCi (DW) Diesel......213
Engine oil check.............................213Engine coolant check...................214Brake and clutch fluid check.......215Power steering fluid check..........215Washer fluid check........................216Technical specifications................216
Vehicle careCleaning the exterior....................220Cleaning the interior......................221Repairing minor paint damage.....221
Vehicle batteryBattery care...................................222Using booster cables...................222
Wheels and tyresGeneral information.....................224Changing a road wheel...............224Tyre repair kit.................................229Run flat tyres.................................234Tyre care........................................235
4
Table of contents
Using winter tyres.........................236Using snow chains.......................236Tyre pressure monitoring
system........................................236Technical specifications...............238
Vehicle identificationVehicle identification plate...........242Vehicle identification number
(VIN).............................................242
Technical specific-ations
Technical specifications...............243
TelephoneGeneral information.....................252Telephone setup...........................252Bluetooth setup............................254Telephone controls......................255Using the telephone - Vehicles
Without: Navigation System.....256Using the telephone - Travel Pilot
EX................................................259
Voice controlPrinciple of operation...................262Using voice control.......................263Audio unit commands.................263Telephone commands................268Navigation system
commands.................................273Climate control commands........273
AppendicesElectromagnetic compatibility.....276
Type approvals..............................277
5
Table of contents
6
ABOUT THIS HANDBOOK
Thank you for choosing Ford. Werecommend that you take some timeto get to know your vehicle byreading this handbook. The more thatyou know about it, the greater thesafety and pleasure you will get fromdriving it.
Note: This handbook describesevery model and option, sometimeseven before they are generallyavailable. It may describe options notfitted to your vehicle.
Note: Always use and operate yourvehicle in line with all applicable lawsand regulations.
Note: Pass on this handbook whenselling your vehicle. It is an integralpart of the vehicle.
SYMBOLS GLOSSARY
Symbols in this handbook
WARNING
You risk death or serious injuryto yourself and others if you do
not follow the instructions highlightedby the warning symbol.
CAUTION
You risk damaging your vehicleif you do not follow the
instructions highlighted by the cautionsymbol.
Symbols on your vehicle
When you see these symbols, readand follow the relevant instructionsin this handbook before touching orattempting adjustment of any kind.
PARTS ANDACCESSORIES
Now you can be sure thatyour Ford parts are Fordparts
Your Ford has been built to thehighest standards using high qualityFord Original Parts. As a result, youcan enjoy driving it for many years.
Should the unexpected occur and amajor part needs replacing, werecommend that you accept nothingless than Ford Original Parts.
The use of Ford Original Partsensures that your vehicle is repairedto its pre-accident condition andmaintains its maximum residual value.
Ford Original Parts match Ford'sstringent safety requirements andhigh standards of fit, finish andreliability. Quite simply, they representthe best overall repair value, includingparts and labour costs.
7
Introduction
Now it is easier to tell if you havereally been given Ford Original Parts.The Ford logo is clearly visible on thefollowing parts if they are FordOriginal Parts. If your vehicle has tobe repaired, look for the clearly visibleFord branding and make sure thatonly Ford Original Parts have beenused.
Look for the Ford logo onthe following parts
Sheet metal
Bonnet Doors Luggage compartment lid or
tailgate
E88678
Bumper and radiator grille
Radiator grille Front and rear bumper
E88505
Exterior mirror
E88506
Glass
Rear window Side glass Windscreen
8
Introduction
E88507
Lighting
Rear lamps Headlamp
E88508
9
Introduction
QUICK START
Instrument panel overview - left-hand drive
A I J K L MCB G HFED
V O NU T S R Q P
E87719
10
Quick start
Instrument panel overview - right-hand drive
E87720
M D E F B ALK G CHJI
N VPT S R Q UO
Lighting controls. See Lighting control (page 56).AAir vents. See Air vents (page 109).BDirection indicators. See Direction indicators (page 61).Telephone control buttons. See Telephone controls (page 255).Voice control buttons. See Using voice control (page 263).
C
Instrument cluster. See Gauges (page 79).DInformation display controls. See Information displays (page 85).EWiper lever. See Windscreen wipers (page 51).FStart Button. See Keyless starting (page 136).GAudio or navigation unit. See separate handbook.H
11
Quick start
Stability control (ESP)switch. See Using stability control (page153).
I
Parking aid switch. See Using the parking aid (page 159).JHazard warning flasher switch. See Hazard warning flashers(page 59).
K
Passenger airbag deactivation warning lamp. See Disabling thepassenger airbag (page 32).
L
Heated windscreen and heated rear window switches. See Heatedwindows and mirrors (page 116).
M
Climate controls. See Manual climate control (page 110). SeeAutomatic climate control (page 113).
N
Cigar lighter. See Cigar lighter (page 130).OIgnition switch. See Ignition switch (page 136).PCruise control switches. See Using cruise control (page 161).Adaptive cruise control switches. See Using ACC (page 165).
Q
Steering wheel adjustment lever. See Adjusting the steeringwheel (page 49).
R
Horn.S
Cruise control switches. See Using cruise control (page 161).Adaptive cruise control switches. See Using ACC (page 165).
T
Driver Knee airbag. See Principle of operation (page 28).UStorage compartment. See Storage compartments (page 132).V
12
Quick start
Keyless entry
E78276
Passive locking and unlockingrequires a valid passive key to belocated within one of the threeexternal detection ranges.
Unlocking the vehicle
E78278
Pull a door handle to unlock all thedoors and the luggage compartmentlid and disarm the alarm.
Locking the vehicle
E87384
E87435
See Keyless entry (page 40).
Keyless starting
E85766
13
Quick start
Press the start button.
See Keyless starting (page 136).
Engine idle speed afterstarting
The engine may idle at a higherspeed than normal immediately afterstarting from cold.
See Starting the engine (page136).
Adjusting the steeringwheel
WARNING
Never adjust the steering wheelwhen the vehicle is moving.
E71221
See Adjusting the steeringwheel (page 49).
Electric folding mirrors
E72623
See Electric exterior mirrors(page 76).
Information displays
E70499
Use the arrow buttons to navigatethrough the menus and press OK tomake a selection.
See Information displays (page85).
14
Quick start
Autolamps
E70719
The headlamps will come on and gooff automatically depending on theambient light.
See Lighting control (page 56).
Direction indicators
E70727
Note: Tap the lever up or down tomake the direction indicators flashonly three times.
Autowipers
B
C
D
AE70696
Single wipeA
AutowipersB
Normal wipeC
High speed wipeD
E70316
A
B
High sensitivityA
Low sensitivityB
See Autowipers (page 51).
15
Quick start
Memory function
WARNING
Do not use the memory storefunction when the vehicle is
moving.
A
B
E86768
Seat adjustment controls.A
Memory pre-set buttons.B
1. Vehicles without keyless starting,insert the ignition key and turn itto position I or II. Vehicles withkeyless starting, press the startbutton.
2. Adjust the seat and exteriormirrors to the desired position.
3. Press and hold the desiredpre-set button B for at least 3seconds.
4. A message will be shown in thedisplay.
5. A chime will sound to confirm.
See Memory function (page 133).
Manual climate control
Heating the interior quickly
E71377
Cooling the interior quickly
E71381
Defrosting and demisting thewindscreen
E71382
16
Quick start
See Manual climate control(page 110).
Automatic climate control
E70304
See Automatic climate control(page 113).
Selecting reverse gear
Vehicles with a 6-speedtransmission
Vehicles with a petrol engine
E75051
1
2
Vehicles with a diesel engine
E75052
2
1
See Manual transmission (page147).
Automatic transmission
Selector lever positions
E80836
S
ParkP
ReverseR
NeutralN
17
Quick start
DriveD
Manual shifting and sportmode
S
WARNING
Apply the brakes before movingthe selector lever and keep
them applied until you are ready tomove off.
See Automatic transmission(page 148).
Fuel filler flap
WARNINGSTake care when refuelling toavoid spilling any residual fuel
from the fuel pipe nozzle.
We recommend that you waitat least 10 seconds before
removing the fuel pipe nozzle to allowany residual fuel to drain into the fueltank.
E86613
Press the flap to open it. Open theflap fully until it engages.
When you insert the fuel pipe nozzle,a spring loaded inhibitor will open ifthe correct size nozzle is detected.This will prevent filling up with thewrong fuel.
See Fuel filler flap (page 143).
18
Quick start
CHILD SEATS
E68916
WARNINGSSecure children that are lessthan 150 centimetres tall or less
than 12 years of age in a suitable,approved child restraint, in the rearseat.
Original text according to ECER94.01: Extreme Hazard! Do not
use a rearward facing child restrainton a seat protected by an air bag infront of it!
Read and follow themanufacturers instructions
when you are fitting a child restraint.
Do not modify child restraints inany way.
Do not hold a child on your lapwhen the vehicle is moving.
Do not leave unattendedchildren in your vehicle.
WARNINGSIf your vehicle has been involvedin an accident, have the child
restraints checked by properlytrained technicians.
Note: Mandatory use of childrestraints varies from country tocountry.
A choice of ECE approved childrestraints which have beenspecifically tested and approved foryour vehicle are available from yourDealer.
Child restraints for differentmass groups
Use the correct child restraint asfollows:
Baby safety seat
E68918
Secure children that weigh less than13 kilogrammes in a rearward facingbaby safety seat in the rear seat.
19
Child safety
Child safety seat
E68920
Secure children that weigh between13 and 18 kilogrammes in a childsafety seat in the rear seat.
BOOSTER CUSHIONS
WARNINGSDo not install a booster seat ora booster cushion with only the
lap strap of the seat belt.
Do not install a booster seat ora booster cushion with a seat
belt that is slack or twisted.
Do not put the seat belt underyour childs arm or behind its
back.
Do not use pillows, books ortowels to boost your childs
height.
Make sure that your children sitin an upright position.
WARNINGSSecure children that weigh morethan 15 kilogrammes but are
less than 150 centimetres tall in abooster seat or a booster cushion.
Booster seat
E70710
We recommend that you use abooster seat that combines acushion with a backrest instead of abooster cushion only. The raisedseating position will allow you toposition the shoulder strap of theadult seat belt over the centre of yourchilds shoulder and the lap straptightly across its hips.
20
Child safety
Booster cushion
E68924
Integrated booster cushion
WARNINGSDo not use the raised integratedbooster cushion together with
a child safety seat.
The integrated booster cushioncan be used for children that
weigh between 22 and 36kilogrammes (49 and 79 pounds).
CAUTION
Remove the rear seat headrestraint unless the child's head
exceeds the top of the backrest.See Head restraints (page 127).
Unlocking
1
2
E94860
Note: Make sure that the lockingmechanism is fully engaged.
3
E94861
The raised seating position will allowyou to position the shoulder strap ofthe adult seat belt over the centre ofyour childs shoulder and the lapstrap tightly across its hips.
21
Child safety
Locking
Note: Make sure that there are noobstructions in the linkage areabefore locking the integrated boostercushion.
2
E94862
1
Note: Make sure that the lockingmechanism is fully engaged.
E94870
3
CHILD SEATPOSITIONING
WARNINGSWhen using a child restraint witha support leg on a second row
seat, make sure the support leg restssecurely on the floor.
When using a forward facingchild seat on a second row seat,
always remove the head restraintfrom that seat.
Note: When using a child restrainton a front seat, it may prove difficultto tighten the lap section of the seatbelt without slack remaining. If this isthe case, adjust the seatback to thefully upright position and raise theheight of the seat. See Seats (page124).
22
Child safety
Mass group categoriesSeating positions
IIIIII0+0
22 - 36kg
15 - 25kg
9 - 18 kgUp to 13kg
Up to 10kg
UFUFUFXXFront passengerseat with airbag ON
UUUUUFront passengerseat with airbag OFF
UUUUURear seats
X Not suitable for children in this mass group.
U Suitable for universal category child restraints approved for use in this massgroup.
U Suitable for universal category child restraints approved for use in this massgroup. However, we recommend that you secure children in a governmentapproved child restraint, in the rear seat.
UF Suitable for universal category forward facing child restraints approvedfor use in this mass group. However, we recommend that you secure childrenin a government approved child restraint, in the rear seat.
ISOFIX child restraints
Mass group categoriesSeating positions
IIIIII0+0
22 - 36kg
15 - 25kg
9 - 18 kgUp to 13kg
Up to 10kg
XXIL, IUF**ILILRear seat ISOFIXrestraints
XXA, B, B1,C, D
C, D, EERear seat ISOFIXclasses*
X Not suitable for children in this mass group.
23
Child safety
IUF Suitable for universal category ISOFIX child restraints approved for use inthis mass group.
IL Suitable for the following ISOFIX child restraints: Roemer Duo ISOFIX (group1), Roemer Babysafe ISOFIX (group 0+). In addition, any semi-universal ISOFIXchild restraint may be used if indicated in the child seat manufacturers vehiclelist.
* As defined by ECE-R16.
Note: ** When you are purchasing an ISOFIX restraint, make sure that youknow the correct mass group and ISOFIX size class for the intended seatinglocations.
Note: ** Make sure that the top tether mechanism does not interfere withthe luggage cover.
24
Child safety
ISOFIX ANCHOR POINTS
WARNING
Use an anti-rotation devicewhen using the ISOFIX system.
We recommend the use of a toptether or support leg.
Your vehicle is fitted with ISOFIXanchor points that accommodateuniversally approved ISOFIX childrestraints.
The ISOFIX system comprises tworigid attachment arms on the childrestraint that attach to anchor pointson the outboard rear seats, wherethe cushion and backrest meet.Tether anchor points are fitted behindthe outboard rear seats for childrestraints with a top tether.
Top tether anchor points
E87146
E93616
E93514
Attaching a child seat withtop tethers
WARNING
Do not attach a tether strap toanything other than the correct
tether anchor point.
Note: Where applicable, remove theluggage cover to ease installation.See Luggage covers (page 174).
25
Child safety
Note: On 4-door vehicles, makesure the tether strap tighteningmechanism remains accessible whenthe seatback is fully engaged.
E87591
1. Place the child seat on the backseat cushion and fold the relevantseatback forwards. See Rearseats (page 127).
2. Remove the head restraint. SeeHead restraints (page 127).
WARNING
Make sure the top tether strapis not slack or twisted and is
properly located on the anchor point.
3. Route the tether strap to theanchor point.
WARNING
Make sure that the seatback issecure and fully engaged in the
catch.
4. Push the seatback to the uprightposition.
E87145
5. Push the child seat back firmly toengage the ISOFIX lower anchorpoints.
6. Tighten the tether strap in line withthe child seat manufacturer'sinstructions.
26
Child safety
CHILD SAFETY LOCKS
WARNING
You cannot open the doorsfrom inside if you have put the
child safety locks on.
E73697
A
B
LockA
UnlockB
27
Child safety
PRINCIPLE OFOPERATION
Airbags
WARNINGSDo not modify the front of yourvehicle in any way. This could
adversely affect deployment of theairbags.
Original text according to ECER94.01: Extreme Hazard! Do not
use a rearward facing child restrainton a seat protected by an airbag infront of it!
Wear a seat belt and keepsufficient distance between
yourself and the steering wheel. Onlywhen you use the seat belt properly,can it hold you in a position thatallows the airbag to achieve itsoptimum effect. See Sitting in thecorrect position (page 124).
Have repairs to the steeringwheel, steering column, seats,
airbags and seat belts carried out bya properly trained technician.
Keep the areas in front of theairbags free from obstruction.
Do not affix anything to or over theairbag covers.
Do not poke sharp objects intoareas where airbags are fitted.
This could damage and adverselyaffect deployment of the airbags.
Use seat covers designed forseats with side airbags. Have
these fitted by a properly trainedtechnician.
Note: You will hear a loud bang andsee a cloud of harmless powderyresidue if an airbag deploys. This isnormal.
Note: Only wipe airbag covers witha damp cloth.
Driver and front passengerairbags
E74302
The driver and front passengerairbags will deploy during significantfrontal collisions or collisions that areup to 30 degrees from the left or theright. The airbags will inflate within afew thousandths of a second anddeflate on contact with theoccupants, thus cushioning forwardbody movement. During minor frontalcollisions, overturns, rear collisionsand side collisions, the driver andfront passenger airbags will notdeploy.
28
Occupant protection
Driver knee airbag
CAUTION
Do not attempt to open thedriver knee airbag cover.
E86311
The driver knee airbag will deployduring frontal collisions or collisionsthat are up to 30 degrees from theleft or the right. The airbag will inflatewithin a few thousandths of a secondand deflate on contact with theoccupants, thus providing a cushionbetween the drivers knees and thesteering column. During overturns,rear collisions and side collisions, theknee airbag will not deploy.
Note: The knee airbag has a lowerdeployment threshold than the frontairbags. During a minor collision, it ispossible that only the knee airbagdeploys.
Side airbags
E72658
Side airbags are fitted inside theseatback of the front seats. A labelindicates that side airbags are fittedto your vehicle.
The side airbags will deploy duringsignificant lateral collisions. Only theairbag on the side affected by thecollision will deploy. The airbags willinflate within a few thousandths of asecond and deflate on contact withthe occupants, thus providingprotection for the chest and shoulderareas. During minor lateral collisions,overturns, front collisions and rearcollisions, the side airbags will notdeploy.
29
Occupant protection
Curtain airbags
E75004
Curtain airbags are fitted inside thetrim panels over the front and rearside windows. Moulded badges inthe B-pillar trim panels indicate thatcurtain airbags are fitted to yourvehicle.
The curtain airbags will deploy duringsignificant lateral collisions. Only theairbag on the side affected by thecollision will deploy. The airbag willinflate within a few thousandths of asecond and deflate on contact withthe occupants, thus providingprotection for the head. During minorlateral collisions, front collisions, rearcollisions, or overturns the curtainairbags will not deploy.
Seat belts
WARNINGSWear a seat belt and keepsufficient distance between
yourself and the steering wheel. Onlywhen you use the seat belt properly,can it hold you in a position toachieve its optimum effect. SeeSitting in the correct position(page 124).
Never use a seat belt for morethan one person.
Use the correct buckle for eachseat belt.
Do not use a seat belt that isslack or twisted.
Do not wear thick clothing. Theseat belt must fit tightly around
your body to achieve its optimumeffect.
Position the shoulder strap ofthe seat belt over the centre of
your shoulder and position the lapstrap tightly across your hips.
The driver and front passenger seatbelt retractors are fitted with a seatbelt pretensioner. Seat beltpretensioners have a lowerdeployment threshold than theairbags. During minor collisions, it ispossible that only the seat beltpretensioners will deploy.
30
Occupant protection
FASTENING THE SEATBELTS
WARNING
Insert the tongue into the buckleuntil you hear a distinct click.
You have not fastened the seat beltproperly if you do not hear a click.
E74124
E85817
Pull the belt out steadily. It may lockif you pull it sharply or if the vehicle ison a slope.
Press the red button on the buckleto release the belt. Let it retractcompletely and smoothly.
SEAT BELT HEIGHTADJUSTMENT
E87511
Note: Lifting the slider slightly whilepressing the locking button makes iteasier to release the lockingmechanism.
To raise or lower, press the lockingbutton on the adjuster and move asnecessary.
SEAT BELT REMINDER
WARNING
Do not sit on top of a fastenedseat belt to prevent the seat belt
reminder from coming on. Theoccupant protection system will onlyprovide optimum protection whenyou use the seat belt properly.
31
Occupant protection
The seat belt reminderwarning lamp illuminates andan audible warning will
sound if you or your front seatpassenger have not fastened yourseat belts and the vehicle exceeds10 km/h (6 mph). It will also illuminateif your seat belts are unfastenedwhen the vehicle is moving. Theaudible warning will go off after fiveminutes but the seat belt reminderwarning lamp will remain on until youfasten your seat belts.
Deactivating the seat beltreminder
See your dealer.
USING SEAT BELTSDURING PREGNANCY
E68587
WARNING
Position the seat belt correctlyfor your safety and that of your
unborn child. Do not use only the lapstrap or the shoulder strap.
Position the lap strap comfortablyacross your hips and low beneathyour pregnant abdomen. Position theshoulder strap between your breasts,above and to the side of yourpregnant abdomen.
DISABLING THEPASSENGER AIRBAG
WARNING
Make sure that the passengerairbag is disabled when using a
rearward facing child restraint on thefront passenger seat.
E71313
32
Occupant protection
Fitting the passengerairbag deactivation switch
WARNING
If you need to fit a child restrainton a seat protected by an
operational airbag in front of it, havea passenger airbag deactivationswitch fitted. Ask your dealer forfurther information.
Note: The key switch is located inthe glove compartment with anairbag deactivation lamp in theinstrument panel.
If the airbag warning lamp illuminatesor flashes when you are driving, thisindicates a malfunction. SeeWarning lamps and indicators(page 81). Remove the child restraintand have the system checkedimmediately.
Disabling the passengerairbag
A BE71312
DisabledA
EnabledB
Turn the switch to position A.
When you switch the ignition on,check that the passenger airbagdeactivation warning lamp illuminates.
Enabling the passengerairbag
WARNING
Make sure that the passengerairbag is enabled when you are
not using a child restraint on the frontpassenger seat.
Turn the switch to position B.
33
Occupant protection
USING THE KEY
Remote control with flip keyblade
E74382
GENERAL INFORMATIONON RADIO FREQUENCIES
CAUTION
The radio frequency used byyour remote control can also be
used by other short distance radiotransmissions (e.g. amateur radios,medical equipment, wirelessheadphones, remote controls andalarm systems). If the frequencies arejammed, you will not be able to useyour remote control. You can lockand unlock the doors with the key.
Note: You could unlock the doors ifyou press the buttons on the remotecontrol unintentionally.
The operating range between yourremote control and your vehiclevaries depending on theenvironment.
PROGRAMMING THEREMOTE CONTROL
You can programme a maximum ofeight remote controls to use withyour vehicle (including any suppliedwith your vehicle). Ask your dealer forinstructions.
CHANGING THE REMOTECONTROL BATTERY
Remote control with afolding key blade
E74383
1
1. Insert a screwdriver as far aspossible into the slot on the sideof the remote control, push ittowards the key blade andremove the key blade.
34
Keys and remote controls
E743842
2. Twist the screwdriver in theposition shown to start separatingthe two halves of the remotecontrol.
3E74385
3. Twist the screwdriver in theposition shown to separate thetwo halves of the remote control.
CAUTION
Do not touch the batterycontacts or the printed circuit
board with the screwdriver.
4. Carefully prise out the battery withthe screwdriver.
5. Install a new battery (3V CR 2032)with the + facing downwards.
6. Assemble the two halves of theremote control.
7. Install the key blade.
Remote control without afolding key blade
E74386
1. Insert a screwdriver into therecess on the back of the key andremove the key blade.
2. Release the retaining clips withthe screwdriver and separate thetwo halves of the remote control.
CAUTION
Do not touch the batterycontacts or the printed circuit
board with the screwdriver.
3. Carefully prise out the battery withthe screwdriver.
4. Install a new battery (3V CR 2032)with the + facing downwards.
5. Assemble the two halves of theremote control.
6. Install the key blade.
35
Keys and remote controls
LOCKING ANDUNLOCKING
Central locking
You can only centrally lock the doorsif they are all closed.
Note: The drivers door can beunlocked with the key. This needs tobe used if the remote control orkeyless entry is not functioning.
Double locking
WARNING
Do not activate double lockingwhen persons or animals are
inside the vehicle. You will not be ableto unlock the doors from the inside ifyou have double locked them.
E71961
Double locking is a theft protectionfeature that prevents someone fromopening the doors from the inside.You can only double lock the doorsif they are all closed.
Locking and unlockingconfirmation
When you unlock the doors, thedirection indicators will flash once.
When you lock the doors, thedirection indicators will flash twice.
Note: If your vehicle has doublelocking, the direction indicators willonly flash twice once you haveactivated double locking.
Locking and unlocking thedoors with the key
B
E71962
A
B
A
UnlockA
LockB
36
Locks
Double locking the doorswith the key
Turn the key to the lock positiontwice within three seconds to doublelock the doors.
Locking and unlocking thedoors and the luggagecompartment lid with theremote control
E87379
A B C
UnlockA
LockB
Luggage compartment lidunlock
C
Locking the doors and theluggage compartment lid withthe remote control
Press button B once.
Double locking the doors andthe luggage compartment lidwith the remote control
Press button B twice within threeseconds.
Locking and unlocking thedoors from inside
Front doors
E71958
A
B
Lock all doorsA
Unlock all doorsB
Rear doors
To lock the rear doors individually,press button A and close the doorwhen leaving the vehicle.
Luggage compartment lid
Opening the luggagecompartment lid with theremote control
Press button C on the remote controltwice within three seconds.
37
Locks
Closing the luggagecompartment lid
4-door
E89131
5-door
E89132
Estate
E89133
A recessed grip is incorporated insidethe luggage compartment lid tofacilitate closing.
Automatic relocking
The doors will relock automatically ifyou do not open a door within 45seconds of unlocking the doors withthe remote control. The door locksand the alarm will return to theirprevious state.
Reprogramming theunlocking function
If the unlocking function isreprogrammed so that only thedrivers door is unlocked ( SeeProgramming the remotecontrol (page 34). ), note thefollowing:
When you press the unlock buttoneither all the doors are unlocked oronly the drivers door is unlocked.Pressing the unlock button againunlocks all the doors.
GLOBAL OPENING ANDCLOSING
You can also operate the electricwindows with the ignition off via theglobal opening and global closingfunction.
Note: Global closing will only operateif you have set the memory correctlyfor each window. See Electricwindows (page 73).
38
Locks
Global opening
E71955
To open all the windows, press andhold the unlock button for at leastthree seconds. Press either the lockor the unlock button again to stopthe opening function.
Global closing
Vehicles without the key freesystem
WARNING
Take care when using globalclosing. In an emergency, press
a button immediately to stop.
E71956
To close all the windows, press andhold the lock button for at leastthree seconds. Press any buttonagain to stop the closing function.The anti-trap function is also activeduring global closing.
Vehicles with the key freesystem
E78275
WARNING
Take care when using globalclosing. In an emergency, press
the button on the drivers doorhandle to stop.
39
Locks
Note: Global closing can beactivated using the button on thedrivers door handle. Global openingand closing can also be activatedusing the buttons on the passive key.
To close all the windows, press andhold the button on the drivers doorhandle for at least two seconds. Theanti-trap function is also active duringglobal closing.
KEYLESS ENTRY
General information
WARNING
The keyless entry system maynot function if the key is close to
metal objects or electronic devicessuch as mobile phones.
Note: If the door handles are pulledrepeatedly during a short period oftime without the presence of a validpassive key, the system will becomeinoperable for 30 seconds.
The passive entry system will notfunction if: The passive key frequencies are
jammed. The passive key battery is flat.
Note: If the passive entry systemdoes not function, you will need touse the key blade to lock and unlockyour vehicle.
The keyless system allows the driverto operate the vehicle without theuse of a key or remote control.
E78276
Passive locking and unlockingrequires a valid passive key to belocated within one of the threeexternal detection ranges. These arelocated approximately one and a halfmetres from the driver and frontpassenger door handles and theluggage compartment lid.
Passive key
The vehicle can be locked andunlocked with the passive key. Thepassive key can also be used as aremote control. See Locking andunlocking (page 36).
40
Locks
Locking the vehicle
E87384
E87435
WARNING
The vehicle does not lock itselfautomatically. If no locking
button is pressed, the vehicle willremain unlocked.
Note: If locking from the luggagecompartment lid, the passive keymust be within the luggagecompartment lid detection range.
Locking buttons are located on eachof the front doors and the luggagecompartment lid.
To activate central locking and armthe alarm: Press a locking button once.
To activate double locking, to armthe alarm and the interior sensors: Press a locking button twice within
three seconds.
Note: Once activated, the vehiclewill remain locked for approximatelythree seconds. This is to allow you topull a door handle and check if thevehicle is locked. When the delayperiod is over, the doors can beopened again, provided the passivekey is within the respective detectionrange.
Luggage compartment lid
Note: The luggage compartment lidcannot be closed and will pop backup if the passive key is located insidethe luggage compartment.
Note: If a second valid passive keyis located within the luggagecompartment lid detection range, theluggage compartment lid can beclosed.
Unlocking the vehicle
Note: If the vehicle remains lockedfor longer than five days, the key freesystem will enter an energy-savingmode. This is to reduce the dischargeof the vehicle battery. When thevehicle is unlocked while in this mode,the reaction time of the system maybe a little longer than normal.Unlocking the vehicle once willdeactivate the energy-saving mode.
41
Locks
E78278
Pull one of the door handles or theluggage compartment lid handle.
Note: A valid passive key must belocated within the detection range ofthat door.
One long flash of the directionindicators confirms that all the doors,the luggage compartment lid and thefuel filler flap have been unlocked andthat the alarm has been disarmed.
Unlocking only the driver'sdoor
If the unlocking function isreprogrammed so that only thedrivers door is unlocked ( See Keysand remote controls (page 34).), note the following:
If the drivers door is the first doorwhich is opened, the other doors andthe luggage compartment lid willremain locked. All the other doorscan be unlocked from inside thevehicle by pressing the unlock buttonnext to the drivers door handle.Doors can be unlocked individuallyby pulling the interior door handleson those doors.
If the front passenger door or one ofthe rear doors is the first door whichis opened, all the doors and theluggage compartment lid will beunlocked.
Disabled keys
Any keys left inside the vehicle interiorwhen it is locked will be disabled.
A disabled key cannot be used toturn the ignition on or start theengine.
In order to use these passive keysagain, they have to be enabled.
To enable all your passive keys,unlock the vehicle using a passivekey or the remote control unlockingfunction.
All passive keys will then be enabledif the ignition is turned on or thevehicle is started using a valid key.
42
Locks
Locking and unlocking thedoors with the key blade
Type 1
1
2
E78284
1. Slide the release slider in thedirection of the arrow and pull outthe key blade with your thumb.
2. Remove the key blade and insertit into the lock.
Type 2
1
2
E87964
1. Carefully remove the cover.
2. Remove the key blade and insertit into the lock.
43
Locks
PRINCIPLE OFOPERATION
The engine immobiliser is a theftprotection system that preventssomeone from starting the enginewith an incorrectly coded key.
CODED KEYS
Note: Do not shield your keys withmetal objects. This may prevent thereceiver from recognising your keyas a valid one.
Note: Have all of your remainingkeys erased and recoded if you losea key. Ask your dealer for furtherinformation. Have replacement keysrecoded together with your existingkeys.
If you lose a key, you can obtain areplacement from your Ford Dealer.If possible, provide them with the keynumber from the tag provided withthe original keys. You can also obtainadditional keys from your FordDealer.
ARMING THE ENGINEIMMOBILISER
The engine immobiliser is armedautomatically a short time after youhave switched the ignition off.
DISARMING THE ENGINEIMMOBILISER
The engine immobiliser is disarmedautomatically when you switch theignition on with a correctly coded key.
If the message Immobiliser activeappears in the information display,your key has not been recognised.Remove the key and try again.
If you are unable to start the enginewith a correctly coded key, thisindicates a malfunction. Themessage Immobiliser active willappear in the information displaywhen you switch on the ignition.Have the immobiliser checkedimmediately.
44
Engine immobiliser
PRINCIPLE OFOPERATION
Alarm system
Your vehicle may be equipped withone of the following alarm systems:
Perimeter alarm. Perimeter alarm with interior
sensors. Category one alarm with interior
sensors and battery back-upsounder.
Category one alarm with interiorsensors, battery back-up sounderand tilt sensors.
Perimeter alarm
The perimeter alarm is a deterrentagainst unauthorised access to yourvehicle through the doors and thebonnet. It also protects the audio unit.
Interior sensors
E71401
WARNING
The sensors in the interior lampunit must not be covered up. Do
not activate the alarm with full guardif any persons, animals or othermoving objects are inside the vehicle.
The sensors act as a deterrentagainst unauthorised intrusion bysensing any movement within thevehicle.
Battery back-up sounder
The battery back-up sounder is anextra alarm system which will sounda siren when the alarm is triggered.It is armed directly when you lock thevehicle. The sounder has its ownbattery and will sound an alarm sireneven if someone disconnects thevehicle battery or the battery back-upsounder itself.
Tilt sensors
The tilt sensors detect if someoneattempts to steal a wheel or tow thevehicle away by sensing changes inthe inclination of the vehicle.
Note: When travelling on a ferry withthe alarm armed, deactivate the tiltsensors by selecting reduced guard.This will prevent the alarm from beingtriggered by the movement.
Triggering the alarm
Once armed, the alarm is triggeredin any of the following ways:
If someone opens a door, thetailgate or the bonnet without avalid key or remote control.
If someone removes the audio ornavigation system.
If the ignition is turned to positionI, II or III without a valid key.
If the interior sensors detectmovement within the vehicle.
45
Alarm
On vehicles with a batteryback-up sounder, if someonedisconnects the vehicle battery orthe battery back-up sounder itself.
If the tilt sensors detect a changein the inclination of the vehicle.
If the alarm is triggered, the alarmhorn will sound for 30 seconds andthe hazard warning flasher will flashfor five minutes.
Any further attempts to perform oneof the above will trigger the alarmagain.
Full and reduced guard
Full guard
Full guard is the standard setting.
In full guard, the interior and tiltsensors are activated when you armthe alarm.
Note: This may result in false alarmsif animals or moving objects areinside the vehicle or, on vehicles withtilt sensors, when travelling on a ferry.
Reduced guard
In reduced guard, the interior and tiltsensors are deactivated when youarm the alarm.
Note: You can set the alarm toreduced guard for the current ignitioncycle only. The next time you switchon the ignition, the alarm will be resetto full guard.
Ask on Exit
You can set the information displayto ask you each time which level ofguard you wish to set.
If you select Ask on Exit, themessage Reduced guard?appears in the instrument clusterdisplay each time you switch theignition off.
If you wish to arm the alarm withreduced guard, press the OK buttonwhen this message appears.
If you wish to arm the alarm with fullguard, leave the vehicle withoutpressing the OK button.
Selecting full or reduced guard
Note: Selecting Reduced does notset the alarm permanently toreduced guard. It sets it to reducedguard only for the current ignitioncycle. If you regularly set the alarm toreduced guard, select Ask on Exit.
E70499
46
Alarm
E74509
Full Guard
Alarm
ReducedAsk on Exit
1. Press the right arrow button onthe steering wheel to enter themain menu.
2. Highlight Setup with the up anddown arrow buttons and pressthe right arrow button.
3. Highlight Alarm and press theright arrow button.
4. Highlight Reduced or Fullguard. If you prefer to be askedeach time you switch off theignition, select Ask on Exit.
5. Press the OK button to confirmthe selection.
6. Press the left arrow button to exitthe menu. To return to the tripcomputer display directly, hold theleft arrow button pressed.
Information messages
See Information messages(page 99).
ARMING THE ALARM
To arm the alarm, lock the vehicle.See Locks (page 36).
DISARMING THE ALARM
Vehicles without keylessentry
Perimeter alarm
Disarm and silence the alarm byunlocking the doors with the key andswitching the ignition on with acorrectly coded key, or unlocking thedoors or the luggage compartmentlid with the remote control.
Category one alarm
Disarm and silence the alarm byunlocking the doors with the key andswitching the ignition on with acorrectly coded key within 12seconds, or unlocking the doors orthe luggage compartment lid with theremote control.
Vehicles with keyless entry
Note: A valid passive key must belocated within the detection range ofthat door for keyless entry. SeeKeyless entry (page 40).
Perimeter alarm
Disarm and silence the alarm byunlocking the doors and switchingthe ignition on, or unlocking the doorsor the luggage compartment lid withthe remote control.
47
Alarm
Category one alarm
Disarm and silence the alarm byunlocking the doors and switchingthe ignition on within 12 seconds, orunlocking the doors or the luggagecompartment lid with the remotecontrol.
48
Alarm
ADJUSTING THESTEERING WHEEL
WARNING
Never adjust the steering wheelwhen the vehicle is moving.
Note: Make sure that you are sittingin the correct position. See Sittingin the correct position (page 124).
1
2
2
E95178
3E95179
WARNING
Make sure that you fully engagethe locking lever when returning
it to its original position.
AUDIO CONTROL
A
C
BD
E
E72288
Volume upA
Seek upB
Volume downC
Seek downD
ModeE
Mode
Press and hold the mode button toselect the audio source.
Press the mode button to: tune the radio to the next preset
station play the next CD play the other side of a cassette
tape
49
Steering wheel
accept an incoming telephonecall.
end a telephone call.
Seek
Press a seek button to: tune the radio to the next station
up or down the frequency band play the next or the previous CD
track fast forward or rewind the
cassette tape.
Press and hold a seek button to: tune the radio up or down the
frequency band seek through a CD track.
50
Steering wheel
WINDSCREEN WIPERS
B
C
D
AE70696
Single wipeA
Intermittent wipeB
Normal wipeC
High speed wipeD
Intermittent wipe
E70315
BA
C
Short wipe intervalA
Intermittent wipeB
Long wipe intervalC
AUTOWIPERS
CAUTIONSDo not switch autowipers on indry weather conditions. The rain
sensor is very sensitive and thewipers may operate if dirt, mist or flieshit the windscreen.
Replace the wiper blades assoon as they begin to leave
bands of water and smears. If you donot replace them, the rain sensor willcontinue to detect water on thewindscreen and the wipers willoperate, even though the majority ofthe windscreen is dry.
Fully defrost the windscreen inicy conditions before you switch
autowipers on.
Switch autowipers off before youenter a car wash.
E70315
BA
C
High sensitivityA
OnB
Low sensitivityC
51
Wipers and washers
If you switch autowipers on, thewipers will not cycle until water isdetected on the windscreen. The rainsensor will then continuouslymeasure the amount of water on thewindscreen and adjust the speed ofthe wipers automatically.
Adjust the sensitivity of the rainsensor using the rotary control. Withlow sensitivity, the wipers will operatewhen the sensor detects a lot ofwater on the windscreen. With highsensitivity, the wipers will operate ifthe sensor detects a small amountof water on the windscreen.
WINDSCREEN WASHERS
WARNING
Do not operate the windscreenwashers for more than 10
seconds or when the reservoir isempty.
Note: The washer jets are heatedwhen the ignition is on.
E70776
REAR WINDOW WIPERAND WASHERS
Intermittent wipe
E70777
Reverse gear wipe
The rear window wiper will operateautomatically when you selectreverse gear if the wiper lever is inposition B, C or D.
Washer
WARNING
Do not operate the rear windowwasher for more than 10
seconds or when the reservoir isempty.
52
Wipers and washers
E70777
Pull the lever fully towards thesteering wheel and hold it to operatethe washer.
HEADLAMP WASHERS
E70776
The headlamp washers will operatewith the windscreen washers whenthe headlamps are on.
Note: To stop the washer fluidreservoir emptying quickly, theheadlamp washers will not operateevery time that you use thewindscreen washers.
CHECKING THE WIPERBLADES
E66644
Run the tip of your fingers over theedge of the blade to check forroughness.
Clean the wiper blade lips with waterapplied with a soft sponge.
CHANGING THE WIPERBLADES
Windscreen wiper blades
CAUTIONSSet the windscreen wipers in theservice position to change the
wiper blades.
You can use the service positionin winter to provide easier access
to the wiper blades for freeing themfrom snow and ice. The windscreenwipers will return to their normalposition as soon as you switch on theignition so make sure that you fullydefrost the windscreen before youswitch on the ignition.
53
Wipers and washers
Service position
E85833
A
E75188
Switch off the ignition and move thewiper lever to position A within threeseconds. Release the lever when thewindscreen wipers have moved tothe service position.
Changing the windscreenwiper blades
Set the windscreen wipers in theservice position and lift the wiperarms.
E728991
2
1. Press the locking button.
2. Remove the wiper blade.
Note: Make sure that the wiperblade locks into place.
3. Install in the reverse order.
Rear window wiper blades
Changing the rear windowwiper blades - Estate
1. Lift the wiper arm.
2
3
4
E86456
2. Position the wiper blade at rightangles to the wiper arm.
3. Disengage the wiper blade fromthe wiper arm.
4. Remove the wiper blade.
54
Wipers and washers
Note: Make sure that the wiperblade locks into place.
5. Install in the reverse order.
Changing the rear windowwiper blades - 5-door
1. Lift the wiper arm.
E864572
3
2. Press the locking button.
3. Remove the wiper blade.
Note: Make sure that the wiperblade locks into place.
4. Install in the reverse order.
55
Wipers and washers
LIGHTING CONTROL
Lighting control positions
BA C
E70718
OffA
Side and tail lampsB
HeadlampsC
Parking lamps
CAUTION
Prolonged use of the parkinglamps will discharge the battery.
Switch off the ignition.
Both sides
Set the lighting control to position B.
One side
E75505
A
B
Right-hand sideA
Left-hand sideB
Main and dipped beam
E70725
Pull the lever fully towards thesteering wheel to switch betweenmain and dipped beam.
Headlamp flasher
Pull the lever slightly towards thesteering wheel.
56
Lighting
Home safe lighting
Switch the ignition off and pull thedirection indicator lever towards thesteering wheel to switch theheadlamps on. You will hear a shorttone. The headlamps will go offautomatically after three minutes withany door open, or 30 seconds afterthe last door has been closed.
With all doors closed, but within the30 second delay, opening any doorwill result in the three minute timerstarting again.
The home safe lights can becancelled by either pulling thedirection indicator lever towards thesteering wheel again or by turningthe ignition switch on.
AUTOLAMPS
E70719
Note: If you have switchedautolamps on, you can only switchthe main beam on when autolampshas switched the headlamps on.
The headlamps will come on and gooff automatically depending on theambient light.
FRONT FOG LAMPS
E70721
WARNING
Only use the front fog lampswhen visibility is considerably
restricted by fog, snow or rain.
REAR FOG LAMPS
E70720
WARNINGSOnly use the rear fog lampswhen visibility is restricted to less
than 50 metres.
Do not use the rear fog lampswhen it is raining or snowing and
visibility is more than 50 metres.
57
Lighting
HEADLAMP LEVELLING
Note: Vehicles with Xenonheadlamps are equipped withautomatic headlamp levelling.
E70722
A B
Raised headlamp beamsA
Lowered headlamp beamsB
You can adjust the level of theheadlamp beams according to thevehicle load.
Recommended headlamp levelling switch positions
Switch positionLoad in luggagecompartment
Load
Second rowseats
Front seats
0--1-2
0 (0.52)--1-2
1 (0.52)-31-2
3 (0.52)Max131-2
4 (1.52)Max1-1
1 See Vehicle identification (page 242).2 Vehicles with active suspension.
58
Lighting
HAZARD WARNINGFLASHERS
Note: Depending on applicable lawsand regulations in the country forwhich your vehicle was originally built,the hazard warning flashers may flashif you brake heavily.
E71943
For item location: See Quick start(page 10).
ADAPTIVE FRONT LIGHTING SYSTEM (AFS)
E72897
A
B
A
B
without AFSA
with AFSB
59
Lighting
The AFS adjusts the headlampdipped beam depending on vehicledirection and speed. It improvesvisibility when you are driving at nightand helps to reduce headlamp glarefor oncoming drivers.
The system will not operate when thevehicle is stationary, when you haveswitched on the daytime runninglamps or when you have selectedreverse gear.
A message will appear in theinformation display if the systemmalfunctions. See Informationmessages (page 99). Theheadlamps will move to a fixedcentral or dipped position. Have thesystem checked as soon as possible.
Cornering lamps
E72898
B
A
B
A
Headlamp beamA
Cornering lamp beamB
The cornering lamps illuminate theinside of a corner when you areturning.
60
Lighting
DIRECTION INDICATORS
E70727
Note: Tap the lever up or down tomake the direction indicators flashonly three times.
INTERIOR LAMPS
Courtesy lamp
CBA
E71945
OffA
Door contactB
OnC
If you set the switch to position B, thecourtesy lamp will come on when youunlock or open a door or the luggagecompartment lid. If you leave a dooropen with the ignition switch off, thecourtesy lamp will go offautomatically after some time toprevent the vehicle battery fromdischarging. To switch it back on,switch on the ignition for a short time.
The courtesy lamp will also come onwhen you switch off the ignition. It willgo off automatically after a short timeor when you start or restart theengine.
If you set the switch to position Cwith the ignition switch off, thecourtesy lamp will come on. It will gooff automatically after a short time toprevent the vehicle battery fromdischarging. To switch it back on,switch on the ignition for a short time.
Reading lamps
E71946
If you switch off the ignition, thereading lamps will go off automaticallyafter some time to prevent thevehicle battery from discharging. Toswitch them back on, switch on theignition for a short time.
61
Lighting
Vanity mirror lamps
A
B
E72900
OffA
OnB
If you switch off the ignition, the vanitymirror lamps will go off automaticallyafter a short time to prevent thevehicle battery from discharging. Toswitch them back on, switch on theignition for a short time.
REMOVING A HEADLAMP
WARNING
Have Xenon bulbs changed bya trained technician. There is a
risk of electric shock.
1. Open the bonnet. See Openingand closing the bonnet (page203).
E85995
2. Remove the screws.
E88843
3. Remove the plastic screw andretainer.
62
Lighting
54E85996
4. Carefully pull the corner of thegrille and bumper towards thefront of the vehicle.
5. Carefully lift the corner of theheadlamp and push it as far aspossible towards the back of thevehicle.
7
6
E88982
6. Carefully pull the headlamptowards the centre of the vehicle,behind the grille and bumper, todisengage it from the lower outerfixing point.
7. Remove the headlamp.
CAUTION
When fitting the headlamp, takecare not to damage the locating
points.
Note: When fitting the headlamp,make sure that you fully engage theheadlamp in the lower outer fixingpoint.
Note: When fitting the headlamp,tighten the front screw first and thenthe rear screw.
CHANGING A BULB
WARNINGSSwitch the lights and the ignitionoff.
Let the bulb cool down beforeremoving it.
Have Xenon bulbs changed bya trained technician. There is a
risk of electric shock.
CAUTIONSDo not touch the glass of thebulb.
Only fit bulbs of the correctspecification. See Bulb
specification chart (page 71).
Note: The following instructionsdescribe how to remove the bulbs.Fit replacements in the reverse orderunless otherwise stated.
63
Lighting
Headlamp
Note: Remove the covers to gainaccess to the bulbs.
Direction indicator
1. Remove the headlamp. SeeRemoving a headlamp (page62).
E72259
2
3
2. Turn the bulb holderanti-clockwise and remove it.
3. Gently press the bulb into the bulbholder, turn it anti-clockwise andremove it.
Headlamp main beam
1. Remove the headlamp. SeeRemoving a headlamp (page62).
E72261
3
2
2. Disconnect the electricalconnector.
3. Release the clip and remove thebulb.
Headlamp dipped beam
1. Remove the headlamp. SeeRemoving a headlamp (page62).
E72260
3
2
2. Turn the bulb holderanti-clockwise and remove it.
3. Remove the bulb.
64
Lighting
Cornering lamp
1. Remove the headlamp. SeeRemoving a headlamp (page62).
E72262
3
2
2. Disconnect the electricalconnector.
3. Release the clip and remove thebulb.
Side repeaters
3
2
E85999
1
1. Carefully remove the siderepeater.
2. Hold the bulb holder, turn thehousing anti-clockwise andremove it.
3. Remove the bulb.
Approach lamp
E72264
1
Note: Position the mirror glass as farinwards as possible.
1. Insert a screwdriver into the gapbetween the mirror housing andthe mirror glass and release themetal retaining clip.
E72265
3
2
65
Lighting
2. Remove the lamp.
3. Remove the bulb.
Front fog lamps
E72267
3
2
4
1
Note: You cannot separate the foglamp bulb from the bulb holder.
Note: Do not remove the screws.
1. Loosen the screws.
2. Remove the lamp.
3. Disconnect the electricalconnector.
4. Turn the bulb holderanti-clockwise and remove it.
Rear lamps
Direction indicator, tail andbrake lamp
E86003
1
1. Remove the trim panel.
2
E86004
2. Unclip the bulb holder.
66
Lighting
E86005
3
A
B
Direction indicatorA
Tail and brake lampB
3. Gently press the bulb into the bulbholder, turn it anti-clockwise andremove it.
Reversing lamp, tail lamp andfog lamp
1
E86006
1. Remove the trim panel.
2
E86007
2. Unclip the bulb holder.
3
CB
A
E86008
Reversing lampA
Tail lampB
Fog lampC
3. Gently press the bulb into the bulbholder, turn it anti-clockwise andremove it.
67
Lighting
Central high mounted brakelamp
Remove the trim panel
4-door
13
E87617
1. Detach the clips.
5-door
1
2
E87618
1. Remove the screws.
2. Detach the clips.
Estate
E87619
1. Detach the clips.
Remove the lamp
2
1 1E87620
1. Insert a suitable object into theholes.
2. Carefully pull the lamp towards thefront of the vehicle to release thespring clips.
68
Lighting
E86002
3
3. Remove the lamp.
3
4
E79601
4. Unclip the bulb holder.
5. Remove the bulb.
Number plate lamp
E72789
1. Carefully release the spring clip.
2. Remove the lamp.
3. Remove the bulb.
Interior lamp
Vehicles without interiorsensors
E72788
1. Carefully prise out the lens.
2. Remove the lens.
3. Remove the bulb.
69
Lighting
Vehicles with interior sensors
E72787
1. Carefully prise out the lens.
2. Remove the lens.
3. Remove the bulb.
Reading lamps
Vehicles without interiorsensors
E72796
1. Carefully prise out the lens.
2. Remove the lens.
3. Remove the bulb.
Vehicles with interior sensors
E72786
1. Carefully prise out the lamp.
2. Turn the bulb holderanti-clockwise and remove it.
E73939
3
3. Remove the bulb.
70
Lighting
Vanity mirror lamp
E72785
1. Carefully prise out the lamp.
2. Remove the bulb.
Luggage compartmentlamp
E72784
1. Carefully prise out the lamp.
2. Remove the bulb.
BULB SPECIFICATION CHART
Power (watt)SpecificationLamp
21PY21WFront direction indicator
55H1Headlamp main beam
55H7Headlamp dipped beam
55H1Cornering lamp
5W5WSide repeater
5W5Approach lamp
351H8Front fog lamp
551H11Front fog lamp
5W5WSide lamp
21PY21WRear direction indicator
71
Lighting
Power (watt)SpecificationLamp
21/5P21/5WBrake and tail lamp
4P21/4WTail lamp
21/5P21/5WRear fog lamp
21P21WReversing lamp
55 x W5WCentral high mounted brake lamp
5W5WNumber plate lamp
10FestoonInterior lamp
5BA 9sReading lamp
5W5WVanity mirror lamp
5W5WLuggage compartment lamp1Fit a replacement with the same rating as the one you have removed.
72
Lighting
ELECTRIC WINDOWS
WARNING
Do not operate the electricwindows unless they are free
from obstruction.
Note: If you operate the switchesoften during a short period of time,the system might become inoperablefor a certain time to prevent damagedue to overheating.
Note: You can operate the windowsfor several minutes after you switchoff the ignition. They will bedeactivated as soon as a door isopened.
Note: If you operate both the switchon the relevant door and the switchfor that window on the drivers doorat the same time, the window willstop moving.
Switch on the ignition to operate theelectric windows.
Global opening and globalclosing
You can also operate the electricwindows with the ignition off via theglobal opening and global closingfunction. See Global opening andclosing (page 38).
Note: Global opening and globalclosing will open or close thewindows automatically only onvehicles equipped with four electricwindows.
Note: Global closing will only operateif you have set the memory correctlyfor each window.
Drivers door switches
E70848
You can operate all the windows withthe switches on the door trim panelof the drivers door.
Front and rear passengersdoor switches
E70849
73
Windows and mirrors
Opening and closing thewindows automatically
Press or lift the switch to the secondaction point and release it. Press orlift it again to stop the windows.
Safety switch for rearwindows
Note: You can always operate therear windows from the drivers door.
E70850
A switch in the drivers door disablesthe rear electric window switches.
The light in the switch illuminates andthe lights in the rear window switchesgo off when the rear windows aredisabled.
Anti-trap function
WARNING
Careless closing of the windowscan override the protection
function and cause injuries.
The electric windows will stopautomatically while closing andreverse some distance if there is anobstacle in the way.
Overriding the anti-trapfunction
CAUTION
While you close the window forthe third time, the anti-trap
function is disabled. Make sure thereare no obstacles in the way of theclosing window.
To override this protection functionwhen there is a resistance, forexample, in the winter, proceed asfollows:
1. Close the window twice until itreaches the resistance and let itreverse.
2. Close the window a third time tothe resistance. The anti-trapfunction is disabled and youcannot close the windowautomatically. The window willoverride the resistance and youcan close it fully.
3. If the window does not close afterthe third attempt, have it checkedby a properly trained technician.
74
Windows and mirrors
Resetting the memory ofthe electric windows
WARNING
The anti-trap function isdeactivated until you have reset
the memory.
After the battery has beendisconnected from the vehicle youmust reset the memory separatelyfor each window:
1. Lift the switch until the window isfully closed. Hold the switch liftedfor one more second.
2. Release the switch and lift it again,two or three times, for one moresecond.
3. Open the window and try to closeit automatically.
4. Reset and repeat procedure if thewindow does not closeautomatically.
Safety mode
WARNING
The anti-trap function is notactive during this procedure.
If the system detects a malfunction,it enters a safety mode. The windowswill move for only about 0.5 secondsat a time and then stop again. Closethe windows by pressing the switchagain when the windows stopmoving. Have this checkedimmediately.
EXTERIOR MIRRORS
Convex mirrors
E71042
WARNING
Do not overestimate thedistance of the objects that you
see in the convex mirror. Objectsseen in convex mirrors will appearsmaller and further away than theyactually are.
Folding mirrors
E71043
Make sure that you fully engage themirror in its support when returningit to its original position.
75
Windows and mirrors
ELECTRIC EXTERIORMIRRORS
A CB
E70846
Left-hand mirrorA
OffB
Right-hand mirrorC
Mirror tilting positions
E70847
The electric exterior mirrors are fittedwith a heating element that willdefrost or demist the mirror glass.See Heated windows andmirrors (page 116).
Electric folding mirrors
The electric folding mirrors operatewith the ignition on.
Note: You can operate the mirrors(mirror tilting and folding) for severalminutes after you switch off theignition. They will be deactivated assoon as a door is opened.
E72623
Press the button to fold or unfold themirrors.
If you press the switch again whilethe mirrors are moving, they will stopand reverse the direction ofmovement.
76
Windows and mirrors
Note: When the mirrors areoperated often during a short periodof time, the system may becomeinoperable for a period of time toprevent damage due to overheating.
Reverse mirror dipping
Depending on the selected mirrorposition (A or C), the relevant exteriormirror will dip whenever you selectreverse gear, giving you a view of thekerb.
When you first use this feature, themirrors will dip to a preset position.You can programme the degree ofdipping using the following sequence:
Note: You can disable this featureby leaving the electric exterior mirrorselector switch in position B.The exterior mirrors will return to theoriginal position: If the vehicle speed exceeds 10
km/h (6 mph). Approximately 10 seconds after
reverse gear has beendisengaged.
If the electric exterior mirrorselector switch is returned toposition B.
Passive setting
1. Turn the ignition on. Do not startthe engine.
2. Select the desired exterior mirror(A or C).
3. Select reverse gear, the selectedexterior mirror will adjust to apreset position.
4. Adjust the mirrors to the requireddipped position.
5. Disengage reverse gear.
The settings will be storedautomatically.
Active setting
1. Turn the ignition on. Do not startthe engine.
2. Select the desired exterior mirror(A or C).
3. Select reverse gear, the selectedexterior mirror will adjust to apreset position.
4. Adjust the mirror to the requireddipped position.
5. Press and hold the desiredpre-set button until a single chimesounds to confirm. See Memoryfunction (page 133).
INTERIOR MIRROR
E71272
Dip the mirror to reduce glare whendriving at night.
77
Windows and mirrors
AUTO-DIMMING MIRROR
E71028
The auto-dimming mirror will adjustautomatically when hit by glaring lightfrom behind. It will not work when youhave selected reverse gear.
78
Windows and mirrors
GAUGES
Type 1 and 2
BA C D
E72984
TachometerA
Engine coolant temperature gaugeB
Fuel gaugeC
SpeedometerD
79
Instruments
Type 3
A B
CDEE87713
TachometerA
SpeedometerB
Engine coolant temperature gaugeC
Fuel gaugeD
Message centre. See Information displays (page 85).E
Engine coolant temperaturegauge
Shows the temperature of the enginecoolant. At normal operatingtemperature, the needle will remainin the centre section.
CAUTION
Do not restart the engine until thecause of overheating has been
resolved.
80
Instruments
If the needle moves towards 120C,the engine is overheating. Stop theengine, switch the ignition off anddetermine the cause once theengine has cooled down. SeeEngine coolant check (page 214).
Fuel gauge
The arrow adjacent to the fuel pumpsymbol tells you on which side ofyour vehicle the fuel filler cap islocated.
WARNING LAMPS ANDINDICATORS
The following warning lamps andindicators will illuminate briefly whenyou switch the ignition on to confirmthat the system is operational: ABS Airbag Brake system Engine Frost Ignition Oil pressure (all except 2.5L
Duratec-ST) Stability control (ESP).
If a warning or indicator lamp doesnot illuminate when the ignition isswitched on, it indicates amalfunction. Have the systemchecked by properly trainedtechnician.
ABS warning lamp
It will flash when the systemis operating. If it illuminateswhen driving, this indicates
a malfunction. Have the systemchecked by a properly trainedtechnician. You will continue to havenormal braking (without ABS) buthave this checked as soon aspossible.
Airbag warning lamp
If it does not illuminate, if itstays on or illuminatesintermittently or continuously
while driving, this indicates amalfunction. Have the systemchecked by a properly trainedtechnician.
Brake system warning lamp
WARNING
Reduce your speed gradually.Use your brakes with great care.
Do not step on the brake pedalabruptly.
If it illuminates when you aredriving, this indicates amalfunction in one of the
brake circuits. Check the brake fluidlevel. See Brake and clutch fluidcheck (page 215).
WARNING
Have this checked immediately.
81
Instruments
If the brake system warning lampilluminates with the ABS warning lampor the stability control (ESP) warninglamp, this indicates a malfunction.Stop your vehicle as soon as it is safeto do so and have this checkedbefore continuing you journey.
Cruise control indicator
E71340
It will illuminate when youhave set a speed using thecruise control system. See
Using cruise control (page 161).On vehicles with adaptive cruisecontrol (ACC), the indicator willilluminate when ACC is active. SeeUsing ACC (page 165).
Direction indicators
Flashes during operation. Asudden increase in the rateof flashing warns of a failed
indicator bulb. See Changing abulb (page 63).
Engine warning lamp
If it illuminates with theengine running, thisindicates a malfunction. If it
flashes when you are driving,reduce the speed of yourvehicle immediately. If itcontinues to flash, avoid heavyacceleration or deceleration. Havethe system checked by a properlytrained technician immediately.
Forward alert indicator
It will illuminate when thisfeature is active. SeeForward alert function
(page 168).
Front fog lamp indicator
It will illuminate when youswitch the front fog lampson.
Frost warning lamp
It will illuminate and gloworange when the outside airtemperature is between 4C
(39.2F) and 1C (33.8F). It will glowred when the temperature is below1C (33.8F).
Glow plug indicator
See Starting a dieselengine (page 140).
Headlamp indicator
It will illuminate when youswitch the headlamp dippedbeam or the side and tail
lamps on.
82
Instruments
Ignition warning lamp
If it illuminates when you aredriving, this indicates amalfunction. Switch off all
unnecessary electrical equipment.Have the system checked by aproperly trained technicianimmediately.
Low fuel level warning lamp
If it illuminates, refuel as soonas possible.
Main beam indicator
It will illuminate when youswitch the headlamp mainbeam on. It will flash when
you use the headlamp flasher.
Maximum engine speedindicator
It will illuminate when themaximum engine speed isreached.
Message indicator
It will illuminate when a newmessage is stored in theinformation display. See
Information messages (page99).
Oil pressure warning lamp
CAUTION
Do not resume your journey if theoil pressure warning lamp
illuminates despite the oil level beingcorrect. Have the system checkedby a properly trained technicianimmediately.
If the lamp stays on afterstarting or illuminates duringa journey, this indicates a
malfunction. Stop your vehicle assoon as it is safe to do so and switchthe engine off. Check the engine oillevel. See Engine oil check (page213).
Rear fog lamp indicator
It will illuminate when youswitch the rear fog lampson.
Seat belt reminder
See Seat belt reminder(page 31).
83
Instruments
Stability control (ESP)warning lamp
While driving, it flashesduring activation of thesystem. After switching on
the ignition, if it does not illuminate orilluminates continuously while driving,this indicates a malfunction. During amalfunction, the system switches off.Have the system checked by aproperly trained technician as soonas possible.
If you switch ESP off, the warninglamp will illuminate. The lamp will goout when you switch the systemback on or when you switch theignition off.
AUDIBLE WARNINGSAND INDICATORS
Switching the chimes onand off
You can deactivate certain chimes.
To set which chimes should sound:
E70499
1. Press the right arrow button onthe steering wheel to enter themain menu.
2. Highlight Setup with the up anddown arrow buttons and pressthe right arrow button.
3. Highlight Chimes and press theright arrow button.
4. Highlight the chime and press theOK button to switch the chime onand off.
5. Press the left arrow button to exitthe menu. Hold the left arrowbutton pressed to return to thetrip computer display.
84
Instruments
GENERAL INFORMATION
WARNING
Do not operate the informationdisplay controls when the
vehicle is moving.
Note: The information display willremain on for several minutes afteryou switch off the ignition.
Various systems on your vehicle canbe controlled using the buttons onyour steering wheel. Correspondinginformation is displayed in theinformation display.
For detailed instructions on audio,navigation, phone etc. refer to theappropriate manual.
Controls
E70499
Press the up and down arrowbuttons:
to scroll through the trip computerdisplays
to scroll through and highlight theoptions within a menu.
Press the right arrow button:
to enter the main menu from thetrip computer displays
to enter a sub-menu.
Press the left arrow button to exit amenu.
Hold the left arrow button pressedat any time to return to the mainmenu display (escape button).
Note: The system will return to thetrip computer displays automaticallyif you do not press any button for aperiod of time.
Press the OK button to choose andconfirm a setting.
Instrument cluster functions
Type 3Type 2Type 1Function
XXXTrip computer
XXXInformation messages
85
Information displays
Type 3Type 2Type 1Function
XXXClock setup
XX-Display settings
XX-Park heater setup
X--Navigation control
X--CD control
X--CD changer control
X--Radio control
X--Phone control
X--Auxiliary input control
Type 1
E80604
Press the up and down arrowbuttons on the steering wheel toscroll through the trip computerdisplays. See Trip computer(page 94).
86
Information displays
Menu structure
Information
Reset trip TripodometerAvg. fuelAvg. speedAll values
Messages
Clock Set clock24 Hour mode12 Hour mode
E87751
Type 2
E74426
6.3Average Fuel
09:00
234.2 km
123456 km
l100km
Press the up and down arrowbuttons on the steering wheel toscroll through the trip computerdisplays. See Trip computer(page 94).
87
Information displays
Menu structure
Reset Trip Trip OdoAvg. fuelAvg. speedAll
EnglishGermanItalianFrenchSpanishTurkishRussianDutchPolish
PortugueseSwedish
Configure
Language
Measure unit
Display
Set Clock24 Hour Mode12 Hour Mode
Always offOn guidanceAlways on
MessagesTyre Press.
MetricImperial
Help ScreenRadio InfoPhone InfoNAV info
Information
Clock
Setup
BA
E87752
88
Information displays
Chimes
Forw. Alert
Low Fuel
ACC warningFA warning
Home lightGeneral warn.General info.
Early
LateNormal
Sensitivity
Warn Audible
Off
ManualAuto
Hill Launch
Check
High loadLow load
Tyre Pressure
Full guard
Ask on exitReduced
Alarm
Aux. Heater
Parkheater
BA
E87753
Set Time
SaturdaySunday
FridayThursday
MondayTuesdayWednesday
Set Time
SaturdaySunday
FridayThursday
MondayTuesdayWednesday
Time 1
Time 2
OnceActive now
89
Information displays
Type 3
E88048
Use the controls to scroll through themenu displays.
Note: After a short period of time,the display will enter a screen savermode. To access the menus fromhere, press the left arrow button.
Device list
T