PHYSICS IS FANTASTIC

PHYSICS PAPER 2

(PART B & C)

WELCOME TO WORKSHOP 2011

Paper 2 ( ESSAY )Paper 2 ( ESSAY )

Part B ( Observing ) => 20

Part C ( Choosing) => 20

ANALYSIS- PASS YEARS ESSAY QUESTIONS

Analisis spmTahun Q9 Q10 Q11 Q122004 Light /mirror

pericope. .Radioactive

Use of radioactive –factoryHeat

( food container)Electromagnet/ Electronic

Transformer / diod

2005 Pressure Archimedes( hydrometer)

Waves(Location for jetty / retaining

wall)

Light Lens.(presbyopia) Electomagnet (transformer- transmission

electricity)

2006 Light / Lens(astronomic telescope )

Electromagnet(motor a.c—d.c)

Heat ( car Radiator) Radioactive(sterilization of med.

equipments)

2007 Pressure Bernoulli( Sailboat)

Electronic Transistor (On when dark–On

when hot)

Force and motion(Safety feature for

lorry)

Waves (spec. for radar

systems )

2008Force and motion(elasticity/safety in

sport)

Radioactive(safety in handling radioactive source)

Light Total internal

reflection ( fibre optic)

Waves Retaining wall

2009 Pressure (Vacuum cleaner)

Radioactive(halt life/ treatment

cancer)

Heat ( Water flask )

Electricity( non-ohmic / lampfilament )

2010 PressureArchimedes( raft)

Waves(dish-solar cooker)

Force and motion(force- lawnmover)

Electricity( circuit )

Analisis mengikut tajuk

Tahun 2 3 4 5 6 7 8 9 10

2004 I I I I

2005 I I I I

2006 I I I I

2007 I I I I

2008 I I I I

2009 I I I I

2010 I I I I

I --- Part BI ---- Part C

• Q 9 : Topic Form 4: Knowledge (1m): Understanding (4m)

: Conceptualize (5m): Problem Solving (10m)

• Q 10 : Topic Form 5: Knowledge (1m): Understanding (4m)

: Conceptualize (5m): Problem Solving (10m)

Section B :ESSAY (Choose One)

30 minutes

Q11 : Topic Form 4 : Knowledge (1m)

: Understanding (4m) : Application (Quantitative) (5m)

: Decision Making (10m)

• Q12 : Topic Form 5 : Knowledge (1m)

: Understanding (4m) : Application (Quantitative) (5m)

: Decision Making (10m)

SECTION C: ESSAY( Choose One)

30 minutes

Construct: Conceptualize

1. Make and state the observation- Observation skill & critical

thinking 2. Make comparison

- State the similarities and differences

3. State the relationship - from the similarities and

differences or state the principle/law involved.

CONSTRUCT: Conceptualization Skill Paper 2 - Section B(Question 9 / Question 10)

5

5 POINTS

1. →9.1 SINK DEEPER THAN 9.22. → BOTH WEIGHT ARE SAME3. → AREA 9.2 IS LARGER THAN 9.I4. → DEPTH INCREASES, PRESSURE

INCREASES5. → AREA INCREASES, DEPTH

DECREASES

1. The Fan blows the air out of the vent

2. Produce a partial vacuum( low pressure) in vacuum cleaner.

3. Atmospheric pressure is higher than the pressure inside the vacuum cleaner.

4. Atmospheric pressure Pushed in the dirt

•

characteristics reasons

characteristics reasonsoil Cannot be compressLow densityHigh boiling point

LighterDoes not change to gas state easily

Small master piston Small force usedBigger slave piston Produce bigger

forceAluminium /Steel Strong (hard ×)/

does not rust easily

• DO WRITE EACH CRITERIA FOR THE CHOSEN SUBJECT

• DO STATE THE CHARACTERISTIC AS HIGH / LOW /LARGE /SMALL

• DO THE JUSTIFICATION BY REPEATING ALL THE CHARACTERICS OF THE CHOSEN SUBJECT.

Section C : DECISION MAKING NOTE

• DON’T WRITE THE CRITERIA FOR ALL THE CHOICES GIVEN IN THE QUESTION

• DON’T STATE VALUE

• DON’T COMPARE BETWEEN THE CRITERIA

Section C : DECISION MAKING NOTE

Pemarkahan -- kes 1

1. Maximum ONLY 4 marks

EXPLAINING ALL THE TYPE OF RETAINING WALL.

BUTTTT……

NOT CHOOSE ANYTHING OR CHOOSE MORE THAN ONE RETAINING WALL.

MARKS given only for the CORRECT REASONs

Pemarkahan -- kes 2 • EXPLAINING ALL THE CHARACTERISTICS

OF given RETAINING WALL

• BUTTTT……CHOOSE wrongly

MARKS only will be given AT WHAT YOU CHOOSE

MAX--- 8 MARKS

DECISION MAKING STEPS

1. Distinguish the characteristics given

2. Explain the properties of every chosen characteristics and give the reason.

3. Distinguish the most suitable material based on the characteristics stated.

4. Give reasons why the material chosen.

Q.12-2008

• A new harbour is to be built at a new location. The suggested new location is either at a bay or a cape. Four models for the structure of the retaining wall are given. Table 12 below shows the location and the characteristics of the four retaining walls.

• Explain the best location and the suitability of each characterictics in Table12.

• Determine the most suitable retaining wall to be used.

• Give the reason for your choice.

Worksheet

Answer Characteristic Explaination / reason

The ______ Water is calmer

______retaining wall.

Decrease the wavelength / higher water pressure at

higher depth.

______ surfaceReduce energy, wave is

reflected at different direction.

______ retaining wall

Protect form high wave / overflow of water.

8 marks

BAY

SLOPING

UNEVEN

HIGH

The most suitable __________________ is _____

Because _________________________________ ________________________________________

2 marks

WRETAINING WALL

LOCATED AT BAY, SLOPING RETAING WALL,

UNEVEN SURFACE AND

HIGH RETAINING WALL

TOTAL : 10 marks

No 11 – characteristics Explaination

Method of moving lawnmover- Push the handle

- Bigger force produced

Mass of lawnmower - Big

- To increase the stability

Size of cutter blade- Big size of cutter blade

- Increase the cutting area of cutting grass

The angle between handle and the horizontal- large

- Force exerted to the ground bigger

- Therefore, I choose lawnmover M, - because it has push handle, big mass of lawnmower, big size of cutter blade

and has large angle between handle and horizontal line

1

34

5 6

79

10

No 12characteristic Reason

Connection of cell- series

Increase the voltage

Connection of battery-Positive terminal of cell to negative terminal of next cell

To allow the flow of current

Connection of resistor and bulb-series

Increase the resistance

Connection of bulb- parallel

If one bulb blow, another bulb still function

- the most suitable circuit is X- Because ………….

1 2

5

4

7

9 10 (1,4,5,7)

7M

Physics is Fantastic

Good Luck & Thank

You

Pn. Aswati Ishak

Worksheet

The most suitable _heating element____ is _____

Because _________________________________ ________________________________________

P

,high melting point,low resistance,

low ability to break at high temperature, and

low oxidation level.

NO.3Characterist

icExplaination / reason

____specific heat capacity.

Easy get cold / becomes cool quickly

______size of ice cream box

Easier to carry

Material for outer box:

______

Poor conductor of heat

______ colour of outer box

Does not absorb heat from surrounding quickly

LOW

smaller

Plastic PVC

Bright

The most suitable _ice cream container_ is _____

Because _________________________________ ________________________________________

R

Low specific heat capacity, small size of ice

cream box, material for outer box is plastic pvc

and bright colour of outer box

No. 4Characterist

icExplaination / reason

____ diameter Reduce the resistance of the cables

_____density The cables will be lighter

______ rate of expansion

Less expansion and sagging in the cable

during hot day

______ melting point

Can withstand high temperature / does not

melting easily

LOW

HIGH

Large

LOW

The most suitable ______cable_______ is _____

Because _________________________________ ________________________________________

Q

Large diameter, low density,

Low rate of expansion and high melting point.