View
39
Download
3
Category
Preview:
DESCRIPTION
rrrr
Citation preview
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 1/50
Module 17 Propeller
Module 17A and 17BLicence Category A, B1 and B3
Propeller
17.1 Fundamentals
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 1
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 2/50
Module 17 Propeller
Copyright Notice© Copyright. All worldwide rights reserved. No part of thispublication may be reproduced, stored in a retrieval system ortransmitted in any form by any other means whatsoever: i.e.
photocopy, electronic, mechanical recording or otherwise withoutthe prior written permission of Total Training Support Ltd.
Knowledge Levels — Category A, B1, B2, B3 and C AircraftMaintenance LicenceBasic knowledge for categories A, B1, B2 and B3 are indicated by theallocation of knowledge levels indicators (1, 2 or 3) against each applicablesubject. Category C applicants must meet either the category B1 or thecategory B2 basic knowledge levels.
The knowledge level indicators are defined as follows:
LEVEL 1• A familiarization with the principal elements of the subject.
Objectives:
• The applicant should be familiar with the basic elements of thesubject.
• The applicant should be able to give a simple description of thewhole subject, using common words and examples.
• The applicant should be able to use typical terms.
LEVEL 2• A general knowledge of the theoretical and practical aspects of the
subject.• An ability to apply that knowledge.
Objectives:
• The applicant should be able to understand the theoreticalfundamentals of the subject.
• The applicant should be able to give a general description of thesubject using, as appropriate, typical examples.
• The applicant should be able to use mathematical formulae inconjunction with physical laws describing the subject.
• The applicant should be able to read and understand sketches,drawings and schematics describing the subject.
• The applicant should be able to apply his knowledge in a practicalmanner using detailed procedures.
LEVEL 3• A detailed knowledge of the theoretical and practical aspects of
the subject.
• A capacity to combine and apply the separate elements ofknowledge in a logical and comprehensive manner.
• Objectives:
• The applicant should know the theory of the subject andinterrelationships with other subjects.
• The applicant should be able to give a detailed description of thesubject using theoretical fundamentals and specific examples.
• The applicant should understand and be able to use mathematicalformulae related to the subject.
• The applicant should be able to read, understand and preparesketches, simple drawings and schematics describing the subject.
• The applicant should be able to apply his knowledge in a practicalmanner using manufacturer's instructions.
• The applicant should be able to interpret results from varioussources and measurements and apply corrective action whereappropriate.
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 2
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 3/50
Module 17 Propeller
Module 17.1 Enabling Objectives and Certificati on Statement
Certification StatementThese Study Notes comply with the syllabus of EASA Regulation
(EC) No.2042/2003 Annex III (Part-66) Appendix I, as amended byRegulation (EC) No.1149/2011, and the associated KnowledgeLevels as specified below:
ObjectivePart-66
ReferenceLicence Category
A B1 B3
Fundamentals 17.1 1 2 2
Blade element theory;
High/low blade angle,reverse angle,angle of attack,
rotational speed;
Propeller slip;
Aerodynamic,centrifugal, and thrustforces;
Torque;
Relative airflow on bladeangle of attack;
Vibration andresonance.
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 3
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 4/50
Module 17 Propeller
Table of Contents
Chapter 17.1 Fundamentals ____________________________ 6
Introduction _______________________________________ 6
Propulsive Force ___________________________________ 6
Propel ler Terms ____________________________________ 8
Effecti ve Pitch, Geometric Pitch and Slip ______________ 10
Ang le of At tack ____________________________________ 12
Propel ler Configuration _____________________________ 11
Pusher _______________________________________________14
Tractor _______________________________________________14
Contra-Rotating ________________________________________16
Counter-Rotating _______________________________________16
Propel ler Solid ity __________________________________ 16
Propel ler Clearances _______________________________ 18
Right and Left Handed Propellers ____________________ 20
The Blade Element _________________________________ 20
Blade Angl e and Blade Pitch ________________________ 22
Blade Twist _______________________________________ 22
Forces on a Blade Element __________________________ 24
Variation of Propel ler Effic iency w ith Speed ____________ 26
Windmi ll ing _______________________________________ 26
Feather ing ________________________________________ 28
Reverse Thrust ____________________________________ 28
Forces Acting on the Propeller _______________________ 28
Centrifugal Force _______________________________________28
Thrust Bending Force ___________________________________ 30
Torque Bending Force___________________________________ 30
Aerodynamic Twisting Moment (ATM) ______________________ 32
Centrifugal Twisting Moment (CTM) ________________________ 32
Turning Moments in the Windmill Condition __________________ 32
Pitch Range ______________________________________ 34
Handli ng Effects - Single Engine Airc raft ______________ 36
Asymmetric Effect (P-Factor) _____________________________ 36
Slipstream Effect _______________________________________ 36
Torque Reaction _______________________________________ 36
Gyroscopic Effect ______________________________________ 38
Thrus t and Power Development ______________________ 40
Power Development in Piston Engines ______________________ 40
Power Development in Turboprop Engines __________________ 40
Turboprop Configurations __________________________ 43
Vibrational Forces and Resonance _____________________ 44
Glossary _________________________________________ 47
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 4
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 5/50
Module 17 Propeller
Intentionally Blank
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 5
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 6/50
Module 17 Propeller
Chapter 17.1 Fundamentals
Introduction
Throughout the development of controlled flight as we know it,every aircraft required some kind of device to convert engine powerto some form of thrust. Nearly all of the early practical aircraftdesigns used propellers to create this thrust.
As the science of aeronautics progressed, propeller designsimproved from flat boards, which merely pushed the air backwards,to aerofoil shapes. These aerofoils produced lift to pull the aircraftforward through aerodynamic action.
As aircraft designs improved, propellers were developed whichused thinner aerofoil sections and had greater strength. Because of
its structural strength, these improvements brought the aluminiumalloy propeller into wide usage. The advantage of being able tochange the propeller blade angle in flight led to wide acceptance ofthe two-position propeller and, later, the constant speed propellersystem.
Today, propeller designs continue to be improved by the use of newcomposite materials, new aerofoil shapes and multi bladeconfigurations.
Propulsive Force
A propeller is a means of converting engine power into propulsiveforce.
A rotating propeller imparts rearward motion to a mass of air andthe reaction to this is a forward force on the propeller blades.
A propeller moves a large mass of air rearward, at a relatively slowspeed, as opposed to a gas turbine engine, which moves a smallmass of air rearward at a high speed.
Thrust = Mass(Vo – VI)
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 6
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 7/50
Module 17 Propeller
Figure 1.1: Thrust from a propeller
Figure 1.2: Blade Terms
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 7
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 8/50
Module 17 Propeller
Propeller TermsBefore starting any discussion about propellers, it is necessary todefine some basic terms to avoid confusion and misunderstanding.
A propeller is a rotating aerofoil that consists of two or more bladesattached to a central hub which is mounted on the enginecrankshaft. The function of the propeller is to convert engine powerto useful thrust. Propeller blades have a leading edge, trailing edge,a tip, a shank, a face, and a back.
Blade angle is the angle between the propeller’s plane of rotation,and the chord line of the propeller aerofoil.
Blade station is a reference position on a blade that is a specifieddistance from the centre of the hub.
Pitch is the distance (in inches or millimetres) that a propellersection will move forward in one revolution.
Pitch distribution is the gradual twist in the propeller blade fromshank to tip.
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 8
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 9/50
Module 17 Propeller
Figure 1.3: Blade Terms
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 9
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 10/50
Module 17 Propeller
Effective Pitch, Geometric Pitch and Slip
Since the angle of a propeller blade varies along its length, aparticular blade station must be chosen to specify the pitch of ablade.
Rather than using blade angles at a reference station, somepropeller manufacturers express pitch in inches at 75% of theradius.
This is the geometric pitch, or the distance this particular elementwould move forward in one revolution along a helix, or spiral,determined by its blade angle.
The effective pitch is the actual distance a propeller advancesthrough the air in one revolution. This cannot be determined by the
pitch angle alone because it is affected by the forward velocity ofthe aeroplane and air density.
The difference between geometric and effective pitch is calledpropeller slip.
If a propeller has a pitch of 50 inches, in theory it should moveforward 50 inches in one revolution. But if the aircraft actuallymoves forward only 35 inches in one revolution the effective pitch is35 inches and the propeller efficiency is 70%.
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 10
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 11/50
Module 17 Propeller
Figure 1.4: Effective pitch, Geometric pitch and Slip (measured atMaster Station)
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 11
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 12/50
Module 17 Propeller
Angle of AttackThrust produced by a propeller, in the same way as lift produced bya wing, is determined by the blade’s angle of attack. It is the acuteangle between the chord line of a propeller blade and the relative
wind.
Angle of attack relates to the blade pitch angle, but it is not a fixedangle. It varies with the forward speed of the aeroplane and theRPM of the propeller.
As an example, when there is no forward speed, angle of attack (α)and blade pitch angle are the same, 20°.
When the aeroplane is moving forward at 60 knots, angle of attackbecomes much less than the blade pitch angle (see figure 1.5).
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 12
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 13/50
Module 17 Propeller
Figure 1.5: Angle of Attack at different forward speeds
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 13
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 14/50
Module 17 Propeller
Propeller ConfigurationThere are four main propeller configurations:
• Pusher
• Tractor
• Contra-Rotating
• Counter-Rotating
All the above types can be between two and five bladed propellers,but usually small two blade propellers are used on small pistonengines and three, four or five bladed propellers are used for highpowered piston or gas turbine engines.
Pusher
A little confusing, as it is sometimes known as the ‘Propeller’. This
type, as the name implies, pushes the airframe through the air andis usually fitted behind the mainplane.
Tractor
This type pulls the airframe through the air and is usually fittedforward of the mainplane.
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 14
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 15/50
Module 17 Propeller
Figure 1.6: Pusher propellers on the Piaggio P.180 Avanti
Figure 1.7: The Cessna 337 Skymaster has a pusher AND a tractorpropeller
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 15
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 16/50
Module 17 Propeller
Contra-Rotating
This configuration is where there are two propeller units on oneshaft, driven by the same engine, but rotating in opposite directions.
This gives the advantage of reducing the disc area, but maintainingthe thrust to enable lower undercarriage configurations to be usedor higher RPM’s from the engine due to reduced tip speed. When apropeller has more than six blades, it becomes inefficient, a contra-rotating propeller is also a method of overcoming this problem.
The rear propeller is usually of a smaller diameter than the frontpropeller, so the blade tips will not be affected by air vortices fromthe front propeller tips.
Counter-Rotating
With a large rotating mass such as a propeller, it will produce asignificant turning moment or torque on the airframe. To overcomethis problem on multi-engined aircraft, counter rotating propellersare often used. In this system you would have, for example, the portengine propeller rotating clockwise and the starboard enginepropeller rotating anti-clockwise, thus balancing the torque effects.
Propeller SoliditySolidity is the term used to describe the ability of the propeller toabsorb power from the engine. For example a C130 propeller will
require high solidity, whilst a Cessna 150 will be somewhat less.
Solidity is defined as ‘The surface area of the propeller di videdby the surf ace area of the propeller dis c’
Solidity may be increased by:
• Increasing number of blades (limited by hub strength socontra-rotating is an option)
• Increasing the chord of the blades (C130 uses ‘paddle’ typeblades)
• Increasing the length of the blades (Limited by tips goingsonic and ground clearance).
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 16
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 17/50
Module 17 Propeller
Figure 1.8: The Contra-rotating propeller of the P51 UnlimitedRacer
Figure 1.9: Counter-rotating propellers
Figure 1.10: Solidity
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 17
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 18/50
Module 17 Propeller
Propeller Clearances
Ground ClearanceThe clearance that exists between the propeller tip and the ground
when the aircraft is in the normal flying attitude is termed groundclearance. On an aircraft with a tail wheel configuration, it wouldhave to be in the takeoff position to measure the ground clearance.
Fuselage ClearanceWith a multi-engined aircraft, this is the clearance between the sideof fuselage and the propeller tip.
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 18
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 19/50
Module 17 Propeller
Ref EASA CS 25.925Figure 1.11: Propeller clearances
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 19
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 20/50
Module 17 Propeller
Right and Left Handed Propellers
A right handed propeller is one which rotates in a clockwisedirection when viewed from aft - looking forward.
A left handed propeller is one which rotates in an anti-clockwisedirection when viewed from aft - looking forward.
The Blade ElementThe aerodynamics of the propeller can most easily be understoodby considering the motion of an element, or section of the propellerblade. Because the blade section of a propeller is an aerofoilsection its aerodynamics can be studied in the same way, using thesame terms.
Rotational Velocity
When the aircraft is stationary the motion of the element is purelyrotational. At a given RPM the velocity of the blade elementincreases as it moves towards the blade tip. Shock wave effects asthe tip speed approaches Mach 1 limit the length of blade. Inaddition there is the obvious limitation of tip to ground clearance.
Forward VelocityWhen the propeller is stationary the forward velocity is entirely thedue to the forward speed of the aircraft (TAS). However when thepropeller is rotating and therefore drawing air through the blade discthen there is an additional induced airflow.
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 20
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 21/50
Module 17 Propeller
Figure 1.12: Aerofoil Terms
Figure 1.13: Airflow Components
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 21
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 22/50
Module 17 Propeller
Blade Angle and Blade PitchIn order to develop the required aerodynamic force on the bladeelement it must be set at a small positive angle of attack to theresultant relative airflow. The Helix Angle plus the angle of attack
equals the blade angle, which is more usually known as blade pitch.
A blade element advances through space as though it wasprescribing a helix. If it were 100% efficient then the distance itmoves in 1-revolution is called the Geometric Pitch. However allblades have tip losses that cause Slip, resulting in a forwarddistance moved per revolution called Effective Pitch.
Blade TwistEarlier it was stated that the rotational velocity increases withdistance towards the blade tip. It is necessary therefore to reduce
the blade angle towards the tip in order to maintain an efficientangle of attack (4o- 6o is the norm). This is the reason for the twiston a blade as shown in figure 1.15.
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 22
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 23/50
Module 17 Propeller
Figure 1.14: Blade Angle pitch relationships
Figure 1.15: Blade Twist
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 23
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 24/50
Module 17 Propeller
Forces on a Blade ElementThe aerodynamic force produced by setting the blade element at asmall positive angle of attack – i.e. the total reaction - may beresolved with respect to the direction of motion of the aircraft. The
component thus obtained which is parallel to the flight path is thethrust force, and that which remains is the propeller torque force.Notice that the propeller torque force is the resistance to motion inthe plane of rotation.
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 24
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 25/50
Module 17 Propeller
Figure 1.16: Blade Twist Figure 1.17: Effect of speed on a fixed pitch propeller
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 25
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 26/50
Module 17 Propeller
Variation of Propeller Efficiency w ith Speed
Figure 1.17 illustrates a fixed pitch propeller traveling at differentspeeds at a constant RPM. If the blade angle is fixed, the angle ofattack will change with variations of forward speed. In particular, asspeed increases, the angle of attack decreases and with it thethrust. The effect on propeller efficiency is as follows:
a At some high forward speed the angle of attack of the bladewill be close to the zero lift incidence and thrust will reduceto zero.
b There will only be one speed at which the blade is operatingat its most efficient angle of attack (4o-6o) and where thepropeller efficiency will be a maximum.
c At low speeds, the thrust will increase as the angle of attackis increased . Provided that the blade is not stalled, thethrust is very large, but the speed is low and the propellerefficiency is low. Therefore at zero forward speed no usefulwork is being done and efficiency is zero.
These limitations to efficiency of a fixed pitch propeller led to the
development of the two pitch propeller and later to the variable pitchpropeller that enables the optimum angle of attack to be maintainedthroughout the flight range.
WindmillingVariable pitch propellers are prone to a condition known aswindmilling. If the propeller suffers a loss of positive torque, thepitch will fine off in an attempt to maintain the governed RPM
selected at the time. The relative airflow will impinge on the frontsurface of the blade section and cause drag and negative torquethat will drive the engine rather than resist rotation.
Figure 1.20 shows that in the windmilling condition there is a smallnegative angle of attack, causing the total reaction to act as shown.Resolving the Total Reaction into the two forces of thrust and torqueresults in the thrust acting in the reverse direction (however themagnitude is not very great) and the torque is acting with, and isassisting, rotation. It is this force that causes the propeller to speedup and cause a potentially damaging over speed of the powerplant.
In addition the reverse thrust and extra form drag caused by the flatface of the propeller causes large drag forces to occur and hencecause considerable asymmetric forces on a twin or multiple engineaircraft.
The aerodynamics are exactly the same as that which drives aground based windmill, hence the name of this condition.
Note that the windmill position is defined as having a small positiveblade angle. However this will also mean it has a small negativeangle of attack.
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 26
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 27/50
Module 17 Propeller
Figure 1.18: Efficiency Curves
Figure 1.20: Feathered Blade Section
Figure 1.19: Windmilling Propeller
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 27
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 28/50
Module 17 Propeller
FeatheringFollowing engine failure the windmilling propeller would cause dragand possibly cause engine damage due to over speeding leading toseizure or possibly engine fire. By turning the blades so that the
aggregate effect of the blade section produces zero torque, thepropeller is stopped and drag reduces to a minimum. The featheredposition is therefore at approximately 90o to the plane of rotation.
Reverse ThrustIf the propeller is turned through the fine pitch stop to around minus20o and power applied, reverse thrust is obtained. The bladesection is working inefficiently, with the total reaction beingproduced in the reverse direction to normal. Mechanical devices areused to prevent application of power as the propeller passesthrough the windmill position, until safely in the braking range.
This blade position is used on some enabled propellers to providerapid braking after landing, and sometimes to reverse the aeroplaneout from its parked position. A mechanical lock is oftenincorporated to prevent the pilot selecting reverse pitch whilstairborne.
Forces Acting on the PropellerWhen a propeller rotates, many forces interact and cause tension,twisting, and bending stresses within the propeller.
These forces are:
• Centrifugal Force
• Bending Force
• Torque Bending Force
• Aerodynamic Twisting Moment (ATM)
• Centrifugal Twisting Moment (CTM)
Centrifugal Force
Centrifugal force puts the greatest stress on a propeller as it tries topull the blades out of the hub. It is not uncommon for the centrifugalforce to be several thousand times the weight of the blade. For
example, a 10 kg propeller blade turning at 2,700 RPM may exert aforce of 50 tons on the blade root.
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 28
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 29/50
Module 17 Propeller
Figure 1.21: Reverse Thrust
Figure 1.22: Propeller Centrifugal Force
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 29
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 30/50
Module 17 Propeller
Thrust Bending Force
Thrust bending force attempts to bend the propeller blades forwardat the tips, because the lift toward the tip of the blade flexes the thin
blade sections forward. Thrust bending force opposes centrifugalforce to some degree.
Torque Bending Force
Torque bending forces try to bend the propeller blade back in thedirection opposite the direction of rotation.
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 30
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 31/50
Module 17 Propeller
Figure 1.23: Thrust Bending Force
Figure 1.24: Propeller Torque Bending Force
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 31
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 32/50
Module 17 Propeller
Aerodynam ic Twist ing Moment (ATM)
Aerodynamic twisting (or turning) moment tries to twist a blade to ahigher angle. This force is produced because the axis of rotation of
the blade is at the midpoint of the chord line, while the centre of thelift of the blade is forward of this axis. This force tries to increase theblade angle. Aerodynamic twisting moment is used in some designsto help feather the propeller.
Figure 1.25 illustrates how ATM is produced. If the pitch changemechanism is behind the centre of pressure (the normal situation)the Total Reaction will tend to try to turn the blade towards a coarsepitch.
It should be noted that in the normal forward thrust situation theCTM and ATM oppose each other, but be aware that CTM is a
much greater force than ATM and hence CTM will always prevailand try to turn the propeller towards the windmill condition.
Centrifugal Twisting Moment (CTM)
Centrifugal twisting (or turning) moment tries to decrease the bladeangle, and opposes aerodynamic twisting moment. This tendency todecrease the blade angle is produced since all the parts of arotating propeller try to move in the same plane of rotation as theblade centerline. This force is greater than the aerodynamic twistingmoment at operational RPM and is used in some designs todecrease the blade angle.
Figure 1.27 illustrates how the centrifugal force on the bladeproduces tensile stress at the blade root and a torque about thepitch change axis. The CTM tends to ‘fine’ the pitch and thereforethe effort required by the pitch change mechanism to increase theblade angle towards ‘coarse pitch’ is increased.
CTM is greater at higher RPM, and with lower aspect ratio blades
Turning Moments in the Windmill Condition
When the propeller is windmilling the total reaction works in the
opposite direction. As a result ATM will also work in the oppositedirection and add to the CTM force.
Thus, when the power is lost to the propeller, the tendency of theblade to turn to low pitch (windmill position) is very large indeed.
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 32
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 33/50
Module 17 Propeller
Figure 1.25: Propeller Aerodynamic Twisting Moment
Figure 1.26: Propeller Centrifugal Twisting Moment
Figure 1.27: Centrifugal Twisting Moment
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 33
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 34/50
Module 17 Propeller
Pitch RangeThe total pitch range extends from feathered to reverse
Summary of typical blade angle settings indicating the large pitch
range required to meet all requirements of a high performanceengine
Note: Pitch stops are fitted at each of the limits to preventinadvertent operation outside of desired range.
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 34
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 35/50
Module 17 Propeller
Figure 1.28: Pitch Range for Variable Pitch propellers with Reverse
Thrust capability
Figure 1.29: Pitch positions
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 35
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 36/50
Module 17 Propeller
Handling Effects - Single Engine AircraftThere are various handling effects on single engine aircraft inparticular due to the rotating propeller.
• Asymmetric Effect (P-Factor)• Slipstream Effect
• Torque Reaction
• Gyroscopic Effect
Asymmetric Ef fect (P-Factor )
In general, the axis of the propeller will be inclined upwards to thedirection of flight due to the angle of attack of the aircraft.
This causes the downward moving blade to have a greater effectiveangle of attack than the upward moving blade and therefore to
develop a greater thrust
The difference in thrust on the two sides of the propeller disccauses a yawing moment. For a right-handed propeller in a nose-upattitude, the yaw will be to the left.
Slipstream Effect
In passing through the propeller, the air is accelerated and givenvelocity.
The parts of the aircraft that are in the propeller slipstream willtherefore have higher speed air passing over them than the parts
outside the slipstream. The drag of the parts will therefore be higherand the effectiveness of any control surface in the slipstream will begreater.
The rotation given to the slipstream will cause it to meet the fin at anangle and so cause a yawing moment.
This effect may be corrected by offsetting the fin or trimming therudder. The amount of rotation given to the air will depend on thetorque of the propeller and so the yawing moment will depend onthe power setting.
Torque Reaction
In rotating the propeller against the resistance of the air, reaction isproduced which tries to rotate the aircraft in the opposite direction.For example, with a right hand propeller, the aircraft will tend to rollto the left.
This is described by Newton’s Third Law of Motion: “For everyaction there is an equal and opposite reaction”.
This tendency may be corrected by ‘wash in’ on the down goingwing and ‘wash out’ on the up going wing. This method is not used
on modern high performance aircraft.
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 36
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 37/50
Module 17 Propeller
Figure 1.30: P-Factor
Figure 1.32: Torque Reaction causing the aircraft to roll to the left
Figure 1.31: Slipstream Effect
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 37
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 38/50
Module 17 Propeller
Gyroscopic Effect
A rotating propeller has the properties of a gyro. If the plane ofrotation is changed, a moment will be produced at right angles tothe applied moment.
For example, if an aircraft with a right handed propeller is yawed tothe right it will experience a nose down pitching moment due to thegyroscopic effect of the propeller. Similarly, if the aircraft is pitchednose up, it will experience a yaw to the right. On most aircraft, thegyroscopic effects are small and easily controlled.
The property of a gyroscope that is discussed above is known asprecession. See figure 1.33.
If a torque is applied as shown then precession will occur as shown.Direction of precession can be determined by taking the force
causing the torque and rotating it through 90o in the direction ofrotation.
A ‘tail dragger’ single engine aircraft with a right-handed propellerwill experience a yaw to the left as the tail lifts on its takeoff run.
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 38
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 39/50
Module 17 Propeller
Figure 1.33: Gyroscopic Effect
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 39
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 40/50
Module 17 Propeller
Figure 1.34: A tail-wheeled aeroplane experiences a yaw to leftwhen the tail lifts off the ground
Thrust and Power Development
Power Development in Piston EnginesThe power output of a piston engine depends on the density of thecombustible mixture of fuel and air introduced into its cylinders atthat part of the operating cycle known as the induction stroke. Onthis stroke, the piston moves down the cylinder, an inlet valveopens, and the fuel/air mixture, or charge prepared by thecarburetor, enters the cylinder as a result of a pressure differenceacting across it during the stroke. If for example an engine isrunning in atmospheric conditions corresponding to the standardsea level pressure of 14.7 lbf/in2, and the cylinder pressure isreduced to, say 2lbf/in2, then the pressure difference is 12.7 lbf/in2,and it is this pressure difference that pushes the charge into thecylinder.
An engine in which the charge is induced in this manner is said tobe normally aspirated. Its outstanding characteristic is that thepower it develops steadily falls off with decrease in atmosphericpressure.
SuperchargingThe limitation on the high altitude performance of a normallyaspirated engine can be overcome by artificially increasing theavailable pressure so as to maintain as far as possible a sea-level
value in the induction system. The process of increasing pressureand charge density is known as supercharging or boosting, and thedevice employed is, in effect, a centrifugal compressor fittedbetween the carburetor and cylinders and driven from the enginecrankshaft through step-up gearing. Power may be measured ininches of mercury or lbf/in2 and is known as manifold pressure.
An alternative higher power supercharging system uses a turbinedriven centrifugal compressor powered by exhaust waste gases.This later form is often known as a turbo-charger or ground boosting
turbo-charger and is capable of increasing boost pressure aboveatmospheric for take off purposes. This system is fitted at the inletto the induction system and uses a fuel injection system at theinduction valve inlet to mix the fuel and air. Power is normallymeasured in lbf/in2 and is often called boost pressure.
Power Development in Turboprop Engines
A turboprop engine is a gas turbine engine configured to transmitthe majority of the jet exhaust to power a free or power turbineassembly connected directly to a reduction gear that drives apropeller. The propeller always runs slower than the engine andmust be large enough to absorb the power developed by the
engine.
To increase power in a gas turbine engine whether turboprop orpure jet one must increase fuel flow, thus increasing the energyavailable to drive the compressor and to turn the propeller/reductiongear assembly or to produce thrust. Fuel flow is increased byopening a throttle valve in a Fuel Flow Governor. These vary incomplexity but the principle of more fuel for more power is alwaystrue.
Power output in a turbo shaft engine is measured either by Shaft orBrake Horsepower. For a turboprop engine power is measured interms of Torque.
Torque is a function of the resistance to rotation. Therefore for agreater torque, greater power is required to turn the propeller.Resistance to motion can be varied by using a variable pitch
Intentionally Blank
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 40
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 41/50
Module 17 Propeller
propeller. In a coarse pitch setting the propeller is gathering moreair and thus is harder to turn.
Torque meters can be in the form of a mechanical system utilizingoil pressure, or digital strain gauge systems. Total loss of torque willindicate engine failure and can be used to initiate an auto feathersequence.
The fuel control lever in a turboprop engine is often known as thePower Lever . In a pure jet engine it is usually called the ThrottleLever, however both levers do exactly the same thing, they regulatethe fuel supply to the combustion chambers.
Whereas in a piston engine there are two levers to control power -Throttle lever and Propeller Condition Lever - it is more normalin a turboprop engine to have a combined power lever, that through
a cam arrangement presets the variable pitch system to the powerrequired.
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 41
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 42/50
Module 17 Propeller
Figure 1.35: Turboprop engine power development
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 42
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 43/50
Module 17 Propeller
Turboprop ConfigurationsNote all the below configurations all incorporate a reduction gearprior to connecting to the propeller shaft. This is because whilst theturboprop engine is required to rotate at speeds up to 100,000 RPM
to maintain its efficiency, the propeller must rotate at just a fractionof that speed, in order to prevent its tips exceeding sonic speed.
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 43
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 44/50
Module 17 Propeller
Figure 1.36: Turboprop engines configurations
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 44
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 45/50
Module 17 Propeller
Vibrational Forces and ResonanceWhen a propeller is producing thrust, aerodynamic and mechanicalforces are present which cause the blades of the propeller to vibrate(see figure 1.37). A person designing a propeller must take this into
consideration. If this is not done, these vibrations may causeexcessive flexing, hardening of the metal and could result insections of the propeller breaking off during operation.
Aerodynamic forces have a great vibration effect at the tip of theblade where the effects of transonic speeds cause buffeting andvibrations.
Mechanical vibrations are caused by power pulses in a pistonengine and are more destructive then aerodynamic vibrations. Themost critical location when looking for the stresses is about 6 inchesfrom the propeller tip.
Most airframe-engine-propeller combinations have no problem ineliminating the effects of vibrational stresses. However somecombinations are sensitive to certain RPM ranges and they have acritical range indicated on the tachometer by a red arc. The engineshould not be operated in this range. If it is operated in the criticalrange over a period of time, there is a strong possibility that thepropeller will suffer from structural failure due to the vibrationalstresses.
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 45
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 46/50
Module 17 Propeller
Figure 1.37: Propeller Vibration
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 46
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 47/50
Module 17 Propeller
Glossary
Accumulator - A device to aid in unfeathering a propeller.
Aerodynami c tw isting m omen t - An operational force on apropeller which tends to increase the propeller blade angle.
Ang le of att ack - The angle between the chord line of a propellerblade section and the relative wind.
Ant i-icing system - A system which prevents the formation of iceon propeller blades.
Aut omatic propeller - A propeller which changes blade angles inresponse to operational forces and is not controlled from the
cockpit. Trade name: Aeromatic®.
Back - The curved side of a propeller airfoil section that can beseen while standing in front of the aeroplane.
Blade - One arm of a propeller from the hub to the tip.
Blade angle - The angle between the blade section chord line andthe plane of rotation of the propeller.
Blade index number - The maximum blade angle on a Hamilton-Standard counterweight propeller.
Blade paddle.- A tool used to turn the blades in the hub.
Blade root - The portion of a blade which is nearest the hub.
Blade station - A distance from the centre of the propeller hubmeasured in inches.
Boots - Ice elimination components which are attached to theleading edge of propeller blades.
Boss - The centre portion of a fixed-pitch propeller.
Brush block - The component of a de-icing and/or reversingsystem which is mounted on the engine nose case and holds thebrushes which transfer electrical power to the slip ring.
Centrifugal force - The force on a propeller which tends to throwthe blades out from the propeller centre.
Centrifugal twisting moment - The force on a propeller which
tends to decrease the propeller blade angle.
Chord line - The imaginary line which extends from the leadingedge to the trailing edge of a blade airfoil section.
Comparison unit - The unit in a synchronization or synchrophasingsystem which compares the signals of the master engine and theslave engine and sends a signal to correct the slave engine RPM orblade phase angle.
Cone - The component used in a splined-shaft installation whichcenters the propeller on the crankshaft.
Constant-speed system - A system which uses a governor toadjust the propeller blade angle to maintain a selected RPM.
Controllable-pitch propeller - A propeller whose pitch can bechanged in flight by the pilot's control lever or switch.
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 47
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 48/50
Module 17 Propeller
Critical range - The RPM range at which destructive harmonicvibrations exist.
De-icing system - An ice elimination system which allows ice toform and then breaks it loose in cycles.
Dome assembly - The pitch-changing mechanism of aHydromatic® propeller.
Effective pitch - The distance forward that an aircraft actuallymoves in one revolution of the propeller.
Face - The flat or thrust side of a propeller blade.
Feather - The rotation of the propeller blades to an angle of about
90 degrees which will eliminate the drag of a windmilling propeller.
Fixed-pitch propeller - A propeller, used on light aircraft, whoseblade angles cannot be changed.
Flanged shaft - A crankshaft whose propeller mounting surfaceforms a flat plate 90 degrees to the shaft centerline.
Frequency generator - The engine RPM signal generator for somesynchronization systems.
Geometric pitch - The theoretical distance that an aircraft will
move forward in one revolution of the propeller.
Governor - The propeller control device in a constant- speedsystem
Go no-go gauge - A gauge used to measure wear between thesplines of a splined crankshaft.
Ground-adjustable propell er - A propeller which can be adjustedon the ground to change the blade angles.
Hub - The central portion of a propeller which is fitted to the enginecrankshaft and carries the blades.
Hydromatic® - A trade name for one type of Hamilton-Standardhydraulically operated propellers.
Integral oil control assembly - A self-contained propeller controlunit used on some transport aircraft.
Leading edge - The forward edge of a propeller blade.
Overhaul facility - An FAA approved facility for major overhaulsand repairs.
Pitch - The same as geometric pitch. Often used interchangeablywith blade angle.
Pitch distribution - The twist in a propeller blade along its length.
Pitch lock - A mechanism used on some transports to preventexcessive overspeeding of the propeller if the governor fails.
Plane of rotation - The plane in which the propeller rotates, 90degrees to the crankshaft centerline.
Propeller - A device for converting engine horsepower into usablethrust.
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 48
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 49/50
Module 17 Propeller
Propeller disc - The disc-shaped area in which the propellerrotates.
Propeller repair station - See overhaul facility.
Propeller track - The arc described by a propeller blade as thepropeller rotates.
Pulse generator - The unit which generates an RPM and bladeposition signal in a synchrophasing system.
Radial clearance - The distance from the edge of the propeller discto an object near the edge of the disc, perpendicular to thecrankshaft centerline.
Reversing - Rotation of the propeller blades to a negative angle to
produce a braking or reversing thrust.
Safetying - The installation of a safety device such as safety wire ora cotter pin.
Selector valve - Propeller control unit in a two-position propellersystem.
Shank - The thickened portion of the blade near the centre of thepropeller.
Shoe - See boot.
Shoulder - The flanged area on the butt of a propeller blade whichis used to retain the propeller blades in the hub.
Slinger ring - The fluid distribution unit on the rear of a propellerhub using an anti-icing system.
Slip - The difference between geometric pitch and effective pitch.
Snap ring - A component of a splined or tapered shaft installationwhich is used to aid in removal of the propeller.
Spider - The central component on many controllable- pitchpropellers which mounts on the crankshaft and has arms on whichthe blades are installed.
Splined shaft - A cylindrical-shaped crankshaft extension whichhas splines on its surface to prevent propeller rotation on the shaft.
Static RPM - The maximum RPM that can be obtained at fullthrottle on the ground in a no-wind condition.
Synchronization system A system which keeps all engines at thesame RPM.
Synchrophasing system - A refined synchronization system whichallows the pilot to adjust the blade relative position as they rotate.
Tachometer-generator - The RPM-sensing unit of somesynchronization systems.
Tapered shaft - A crankshaft design whose propeller- mountingsurface tapers to a smaller diameter and acts like a cone seatingsurface.
Thrust bending force - An operational force which tends to bendthe propeller blades forward.
Tip - The portion of the blade farthest from the hub.
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 49
S a m p l e
7/17/2019 17.1 Fundamentals (Landscape) - Sample
http://slidepdf.com/reader/full/171-fundamentals-landscape-sample 50/50
Module 17 Propeller
Torque bending for ce - An operational force which tends to bendthe propeller blades in the direction opposite to the direction ofrotation.
Two-position propeller - A propeller which can be changedbetween two blade angles in flight.
Copyright 2014 © Total Training Support LtdModule 17.1 Fundamentals Page 50
S a m p l e
Recommended