View
214
Download
0
Category
Preview:
Citation preview
7/29/2019 3828A20510D Manual%2CInstallation
1/55
ENG
LISH
LG
Room Air ConditionerINSTALLATION MANUAL
LG
website http://www.lgservice.com
IMPORTANT
Please read this instruction manual completely beforeinstalling the product.
When the power cord is damaged, replacement should beperformed by authorized personnel only.
Installation work must be performed in accordance withthe national wiring standards by authorized personnelonly.
Please retain this installation manual for future referenceafter reading it thoroughly.
ESPAO
L
7/29/2019 3828A20510D Manual%2CInstallation
2/55
2 Room Air Conditioner
Room Air Conditioner Installation Manual
TABLE OF CONTENTS
Safety Precautions............................3
Introduction ........................................6
Symbols used in this manual..........6
Features...........................................6
Installation ..........................................7
Installation parts...............................7Installation tools ...............................7
Installation map................................8
Selecting the best location .............9
Piping length and elevation...........10
Fixing installation plate..................11
Drilling a hole in the wall ...............11
Flaring work ...................................12
Connecting the piping ..................13
Connecting the cables ..................19
Checking the drainage..................21
Forming the piping.........................22
Air purging......................................23
Test running ...................................25
Four type "A" screws & plasticanchors
Connecting cable
Installation guide map
Pipes: Gas sideLiquid side
Insulation materials
Additional drain pipe(Outer diameter ..............15.5mm)
Two type "B" screws
Level gauge
Screw driver
Electric drill
Hole core drill(70mm)
Horizontal meter
Flaring tool set
Specified torque wrenches1.8kg.m, 4.2kg.m, 5.5kg.m,6.6kg.m(different depending on model No.)
Spanner........................Half union
A glass of water
Screw driver
Hexagonal wrench(4mm)
Gas-leak detector
Vacuum pump
Gauge manifold
Owner's manual
Thermometer
Remote control holder
InstallationRequirements
Required Parts Required Tools
7/29/2019 3828A20510D Manual%2CInstallation
3/55
Installation Manual 3
ENG
LISH
Safety Precautions
To prevent the injury of the user or other people and property damage, the following instructionsmust be followed.s Be sure to read before installing the air conditioner.s Be sure to observe the cautions specified here as they include important items related to safety.s Incorrect operation due to ignoring instruction will cause harm or damage.The seriousness is
classified by the following indications.
s The meanings of the symbols used in this manual are as shown below.
This symbol indicates the possibility of death or serious injury.
This symbol indicates the possibility of injury or damage to properties only.
s Installation
Be sure not to do.
Be sure to follow the instruction.
Safety Precautions
Always perform grounding.
Otherwise, it may causeelectrical shock.
Dont use a power cord, a
plug or a loose socketwhich is damaged.
Otherwise, it may cause a fireor electrical shock.
For installation of the product,
always contact the servicecenter or a professionalinstallation agency.
Otherwise, it may cause a fire,electrical shock, explosion orinjury.
Securely attach theelectrical part cover to the
indoor unit and the servicepanel to the outdoor unit.
If the electrical part cover ofthe indoor unit and the servicepanel of the outdoor unit arenot attached securely, it couldresult in a fire or electricshock due to dust, water, etc.
Always install an air leakagebreaker and a dedicated
switching board.
No installation may cause afire and electrical shock.
Do not keep or useflammable gases or
combustibles near the airconditioner.
Otherwise, it may cause a fireor the failure of product.
Ensure that an installation frame of theoutdoor unit is not damaged due to use fora long time.
It may cause injury or an accident.
Do not disassemble or repair the productrandomly.
It will cause a fire or electrical shock.
7/29/2019 3828A20510D Manual%2CInstallation
4/55
4 Room Air Conditioner
Safety Precautions
Do not install the product at a place thatther is concern of falling down.
Otherwise, it may result in personal injury.
Use caution when unpacking and installing.
Sharp edges may cause injury.
Take the power plug out ifnecessary, holding the headof the plug and do not touch
it with wet hands. Otherwise, it may cause a fire
or electrical shock.
Do not use the power cordnear the heating tools.
Otherwise, it may cause a fireand electrical shock.
Do not open the suctioninlet of the indoor/outdoorunit during operation.
Otherwise, it may electricalshock and failure.
Do not allow water to runinto electrical parts.
Otherwise, it may cause the
failure of machine or electricalshock.
Hold the plug by the headwhen taking it out.
It may cause electric shock
and damage.
Never touch the metal partsof the unit when removingthe filter.
They are sharp and may
cause injury.
Do not share the outlet withother appliances.
It will cause an electric shockor a fire due to heatgeneration.
Do not use the damagedpower cord.
Otherwise, it may cause a fireor electrical shock.
Do not modify or extend thepower cord randomly.
Otherwise, it may cause a fireor electrical shock.
Take care so that the power
cord may not be pulledduring operation.
Otherwise, it may cause a fireor electrical shock.
Unplug the unit if strange
sounds, smell, or smokecomes from it.
Otherwise, it may causeelectrical shock or a fire.
Keep the flames away.
Otherwise, it may cause a fire.
Do not step on the indoor/outdoor unit anddo not put anything on it.
It may cause an injury through dropping of theunit or falling down.
Do not place a heavy object on the powercord.
Otherwise, it may cause a fire or electricalshock.
When the product is submerged into water,always contact the service center.
Otherwise, it may cause a fire or electricalshock.
Take care so that children may not step onthe outdoor unit.
Otherwise, children may be seriously injureddue to falling down.
s Operation
7/29/2019 3828A20510D Manual%2CInstallation
5/55
Installation Manual 5
ENG
LISH
Safety Precautions
s InstallationInstall the drain hose to ensure that draincan be securely done.
Otherwise, it may cause water leakage.
Install the product so that the noise or hotwind from the outdoor unit may not causeany damage to the neighbors.
Otherwise, it may cause dispute with theneighbors.
Always inspect gas leakage after theinstallation and repair of product.
Otherwise, it may cause the failure of product.
Keep level parallel in installing the product.
Otherwise, it may cause vibration or waterleakage.
Avoid excessive cooling and performventilation sometimes.
Otherwise, it may do harm to your health.
Use a soft cloth to clean. Do not use wax,thinner, or a strong detergent.
The appearance of the air conditioner maydeteriorate, change color, or develop surfaceflaws.
Do not use an appliance for special purposes
such as preserving animals vegetables,precision machine, or art articles.
Otherwise, it may damage your properties.
Do not place obstacles around the flow inlet
or outlet.
Otherwise, it may cause the failure of applianceor an accident.
s Operation
7/29/2019 3828A20510D Manual%2CInstallation
6/55
6 Room Air Conditioner
Introduction
This symbol alerts you to the risk of electric shock.
This symbol alerts you to hazards that may cause harm tothe air conditioner.
This symbol indicates special notes.NOTICE
Introduction
Symbols used in this Manual
Features
Air Intake Vents
Air Outlet Vents
Air Intake Vents
Air Outlet Vents
Connecting
Wires
ConnectingWires
PipingPiping
Drain HoseDrain Hose
Base Plate Base Plate
Air Inlet
Air Filter
Front Panel
Signal Receptor
7/29/2019 3828A20510D Manual%2CInstallation
7/55
Installation Manual 7
ENG
LISH
Installation
Type "A" screw (6 EA) Type "A" screw (8 EA)
Type "B" screw Type "B" screw
Remote control holderRemote control holder
Type 1 Type 2
Installation plate Installation plate
Figure FigureName
Screw driver
Electric drill
Measuring tape, Knife
Hole core drill
Spanner
Torque wrench
Ohmmeter
Hexagonal wrench
Ammeter
Gas-leak detector
Thermometer,
Horizontal meter
Flaring tool set
Name
Installation Parts
Installation Tools
InstallationRead carefully, and then follow step by step.
7/29/2019 3828A20510D Manual%2CInstallation
8/55
8 Room Air Conditioner
Installation
Installation Map
Installation parts you should purchase.
Vertical Air deflector
Air Discarge
Forced Operation Button
Operation Indication Lamps/Signal Receptor Vinyl tape (Wide)
Apply after carrying out adrainage test.
To carry out the drainagetest, remove the air filters
and pour water into the heatexchanger.
Saddle
Gas side piping (Optional Parts)
Liquid side piping (Optional Parts)
Additional drain pipe
Vinyl tape (Narrow)Drain Hose
Base Plate
Air Outlet Vents
Air Inlet Vents
Connecting cable(Optional Parts)
Installation plateSleeveBushing-SleevePutty(Gum Type Sealer)
Bend the pipe as closelyon the wall as possible,but be careful that itdoesn't break.
NOTICE
7/29/2019 3828A20510D Manual%2CInstallation
9/55
Installation Manual 9
ENG
LISH
Installation
Indoor unit
1. Do not have any heat or steam near the unit.
2. Select a place where there are no obstacles
in front of the unit.
3. Make sure that condensation drainage can beconveniently routed away.
4. Do not install near a doorway.
5. Ensure that the interval between a wall andthe left (or right) of the unit is more than10cm. The unit should be installed as high aspossible on the wall, allowing a minimum of
20cm from ceiling.6. Use a stud finder to locate studs to prevent
unnecessary damage to the wall.
Outdoor unit
1. If an awning is built over the unit to preventdirect sunlight or rain exposure, make surethat heat radiation from the condenser is notrestricted.
2. Ensure that the space around the back andsides is more than 30cm. The front of the unitshould have more than 70cm of space.
3. Do not place animals and plants in the pathof the warm air.
4. Take the weight of the air conditioner intoaccount and select a place where noise andvibration are minimum.
5. Select a place where the warm air and noisefrom the air conditioner do not disturbneighbors.
Select the best Location
More than 20cm
More than
10cm
More than 2.3m
More than10cm
Install the indoor unit on the wall where the height from the floor is more than 2.3 meters.
More than 30cm More than 30cm
More
than 60cm
More than 60cm
More than 70cm
7/29/2019 3828A20510D Manual%2CInstallation
10/55
10 Room Air Conditioner
Installation
Piping Length and Elevation
7k, 8k, 9k 3/8" 1/4" 7.5 7 15 2011k, 12k, 14k 1/2" 1/4" 7.5 7 15 20
1/2" 1/4" 7.5 15 30 20
18k, 24k, 26k 5/8" 1/4" 7.5 15 30 20
5/8" 3/8" 7.5 15 30 30
Pipe SizeCapacity(Btu/h) GAS LIQUID
Max.Length A (m)
AdditionalRefrigerant (g/m)
Max.Elevation B (m)
StandardLength (m)
Outdoor unit
Indoor unit
A
B
Outdoor unit
Indoor unit
A
B
AOil trap
Outdoor unit
Indoor unitB
If piping length is more than 5m
Capacity is based on standard length and maximum allowance length is on the basis of reliability.Oil trap should be installed every 5~7 meters.
7/29/2019 3828A20510D Manual%2CInstallation
11/55
Installation Manual 11
ENG
LISH
Installation
Fixing Installation Plate
Drill the piping hole with a 70mm hole coredrill. Drill the piping hole at either the right orthe left with the hole slightly slanted to theoutdoor side.
Drill a Hole in the Wall
5-7mm
(3/16"~5/16")
Indoor
WALL
Outdoor
The wall you select should be strong andsolid enough to prevent vibration
1. Mount the installation plate on the wall with
type "A" screws. If mounting the unit on aconcrete wall, use anchor bolts.
Mount the installation plate horizontally byaligning the centerline using a level.
2. Measure the wall and mark the centerline.It is also important to use cautionconcerning the location of the installationplate-routing of the wiring to power outletsis through the walls typically. Drilling thehole through the wall for pipingconnections must be done safely.
ChassisHook
Installation Plate
Type A
Installation plate
Left rear piping Right rear piping
70mm 70mm
DB
AC
A B C DS4 55 105 65 105
SE 70 110 90 110
S5/S8 100 122 240 122
CHASSIS(Grade)
Distance (mm)
Installation plate
Left rear piping Right rear piping
70mm
133mm
70mm
100mm
ChassisHook
Installation Plate
Type A
7/29/2019 3828A20510D Manual%2CInstallation
12/55
12 Room Air Conditioner
Installation
Flaring Work
Main cause for gas leakage is due to defect in flaring work. Carry out correct flaring work in thefollowing procedure.
Cut the pipes and the cable.
1. Use the piping kit accessory or the pipespurchased locally.
2. Measure the distance between the indoor andthe outdoor unit.
3. Cut the pipes a little longer than measureddistance.
4. Cut the cable 1.5m longer than the pipe length.
Burrs removal
1. Completely remove all burrs from the cut crosssection of pipe/tube.
2. Put the end of the copper tube/pipe in adownward direction as you remove burrs inorder to avoid dropping burrs into the tubing.
Putting nut on
Remove flare nuts attached to indoor andoutdoor unit, then put them on pipe/tube havingcompleted burr removal.(not possible to put them on after flaring work)
Flaring work1. Firmly hold copper pipe in a die in the dimension
shown in the table below.
2. Carry out flaring work with the flaring tool.
Copperpipe 90 Slanted Uneven Rough
Pipe
Reamer
Point down
Flare nut
Copper tube
Bar
Copper pipe
Clamp handleRed arrow mark
Cone
Yoke
Handle
Bar"A"
mm inch mm
6.35 1/4" 1.1~1.39.52 3/8" 1.5~1.7
12.7 1/2" 1.6~1.815.88 5/8" 1.6~1.819.05 3/4" 1.9~2.1
Outside diameter A
7/29/2019 3828A20510D Manual%2CInstallation
13/55
Installation Manual 13
ENG
LISH
Installation
Check
1. Compare the flared work with the figure by.
2. If a flared section is defective, cut it off anddo flaring work again.
Indoor
1. Prepare the indoor unit's piping and drain hose for installation through the wall.
2. Remove the plastic tubing retainer(see theillustration by) and pull the tubing and drainhose away from chassis.
3. Replace only the plastic tubing holder 1, notthe holder 2 in the original position.
1. Route the indoor tubing and the drain hose inthe direction of rear right.
2. Insert the connecting cable into the indoor unitfrom the outdoor unit through the piping hole. Do not connect the cable to the indoor unit. Make a small loop with the cable for easy
connection later.3. Tape the tubing, drain hose, and the
connecting cable. Be sure that the drain hoseis located at the lowest side of the bundle.Locating at the uper side can cause drain panto overflow inside the unit.
If the drain hose is routed inside the room,insulate the hose with an insulation material*
so that dripping from "sweating"(condensation)will not damage furniture or floors.*Foamed polyethylene or equivalent isrecommended.
Inclined
Inside is shiny without scratches
Smooth all round
Even lengthall round
Surfacedamaged
Cracked Uneventhickness
= Improper flaring =
Connecting the Piping
For right rear piping
Drain hose
Connectingpipe
Connecting cable
Tape
Drain hose
7/29/2019 3828A20510D Manual%2CInstallation
14/55
14 Room Air Conditioner
Installation
4. Indoor unit installationHook the indoor unit onto the upper portion ofthe installation plate.(Engage the two hooksof the rear top of the indoor unit with theupper edge of the installation plate.) Ensurethat the hooks are properly seated on the
installation plate by moving it left and right.
Press the lower left and right sides of the unitagainst the installation plate until the hooksengage into their slots(clicking sound).
Connecting the piping to the indoor unit anddrain hose to drain pipe.
1. Align the center of the pipes and sufficientlytighten the flare nut by hand.
2. Tighten the flare nut with a wrench.
3. When extending the drain hose at the indoor
unit, install the drain pipe.
Wrap the insulation material around theconnecting portion.
1. Overlap the connection pipe insulationmaterial and the indoor unit pipe insulation
material. Bind them together with vinyl tapeso that there may be no gap.
2. Wrap the area which accommodates the rearpiping housing section with vinyl tape.
3. Bundle the piping and drain hose together by
wrapping them with vinyl tape for enough tocover where they fit into the rear pipinghousing section.
Drain hose
Connectingcable
Indoor unit tubing Flare nut Pipes
Wrench
Indoor unit tubing
Open-end wrench (fixed)
Connection pipe
Flare nut
Vinyl tape(narrow)Adhesive
Drain pipe
Indoor unit drain hose
Plastic bands Insulation material
Vinyl tape(narrow)
Connection pipe
Connecting cable
Vinyl tape (wide) Wrap with vinyl tape
Indoor unit pipe
Pipe
Wrap with vinyl tape
Drain hose
Pipe
Vinyl tape(wide)
mm inch kgf.m6.35 1/4" 1.8~2.59.52 3/8" 3.4~4.212.7 1/2" 5.5~6.615.88 5/8" 6.3~8.2
Outside diameter Torque
7/29/2019 3828A20510D Manual%2CInstallation
15/55
Installation Manual 15
ENG
LISH
Installation
1. Route the indoor tubing and the drain hose tothe required piping hole position.
2. Insert the piping, drain hose, and the
connecting cable into the piping hole.3. Insert the connecting cable into the indoor unit.
Don't connect the cable to the indoor unit. Make a small loop with the cable for easy
connection later.
4. Tape the drain hose and the connectingcables.
5. Indoor unit installation Hang the indoor unit from the hooks at the
top of the installation plate. Insert the spacer etc. between the indoor
unit and the installation plate and separatethe bottom of the indoor unit from the wall.
Connecting the piping to the indoor unit andthe drain hose to drain pipe.1. Align the center of the pipes and sufficiently
tighten the flare nut by hand.
2. Tighten the flare nut with a wrench.
3. When extending the drain hose at the indoorunit, install the drain pipe.
For left rear piping
Drain pipe
Connectingcable
1 2
Installation plate
Spacer
Indoor unit
8cm
Indoor unit tubing Flare nut Pipes
Wrench
Indoor unit tubing
Connection pipe
Flare nut
Open-end wrench (fixed)
Vinyl tapeAdhesive
Drain hose
Indoor unit drain hose
(narrow)
mm inch kgf.m6.35 1/4" 1.8~2.59.52 3/8" 3.4~4.212.7 1/2" 5.5~6.615.88 5/8" 6.3~8.2
Outside diameter Torque
7/29/2019 3828A20510D Manual%2CInstallation
16/55
16 Room Air Conditioner
Installation
Wrap the insulation material around theconnecting portion.1. Overlap the connection pipe heat insulation
and the indoor unit pipe heat insulationmaterial. Bind them together with vinyl tapeso that there may be no gap.
2. Wrap the area which accommodates the rearpiping housing section with vinyl tape.
3. Bundle the piping and drain hose together bywrapping them with cloth tape over the rangewithin which they fit into the rear pipinghousing section.
Reroute the pipings and the drain hoseacross the back of the chassis.
Indoor unit installation
1. Remove the spacer.2. Ensure that the hooks are properly seated on
the installation plate by moving it left andright.
3. Press the lower left and right sides of the unitagainst the installation plate until the hooksengage into their slots(clicking sound).
Plastic bandsInsulation material
Vinyl tape(narrow)
Connectionpipe
Connecting cable
Indoorunit piping
Pipe
Vinyl tape(wide)
Wrap with vinyl tape
Drain hoseVinyl tape(narrow)
Pipe
Wrap withvinyl tape(wide)
Piping forpassage throughpiping hole
Drain hose
Connectingcable
7/29/2019 3828A20510D Manual%2CInstallation
17/55
Installation Manual 17
ENG
LISH
Installation
Installation Information. For left piping. Follow the instruction below.
Good case
Press on the upper side of clamp and unfold the tubing to downward slowly.
Bad case
Following bending type from right to left may cause damage to the tubing.
7/29/2019 3828A20510D Manual%2CInstallation
18/55
18 Room Air Conditioner
Installation
Outdoor
Align the center of the pipings and sufficientlytighten the flare nut by hand.
Finally, tighten the flare nut with torque wrenchuntil the wrench clicks.
When tightening the flare nut with torquewrench, ensure the direction for tighteningfollows the arrow on the wrench.
mm inch kgf.m
6.35 1/4" 1.8~2.59.52 3/8" 3.4~4.212.7 1/2" 5.5~6.615.88 5/8" 6.3~8.2
19.05 3/4" 9.9~12.1
Outside diameter Torque
Outdoor unit
Liquid side piping(Smaller diameter)
Gas sidepiping(Biggerdiameter)
Torque wrench
7/29/2019 3828A20510D Manual%2CInstallation
19/55
Installation Manual 19
ENG
LISH
Installation
Indoor
Connect the cable to the indoor unit by connecting the wires to the terminals on the control boardindividually according to the outdoor unit connection. (Ensure that the color of the wires of the
outdoor unit and the terminal No. are the same as those of the indoor unit.)
Connecting the Cables
The above circuit diagram is subject to change without notice.
The earth wire should be longer than the common wires.
When installing, refer to the circuit diagram behind the panel front of the indoor unit.
Connect the wires firmly so that they may not be pulled out easily. Connect the wires according to color codes, referring to the wiring diagram.
If a power plug is not used, provide a circuitbreaker between power source and the unit asshown by.
The power cord connected to the "A" unit should be selected according to the followingspecifications(Type "B" approved by HAR or SAA).
The power connecting cable connecting the indoor and outdoor unit should be selected accordingto the following specifications (Type "B" approved by HAR or SAA).
Air
Conditioner
Main power source
Circuit Breaker
Use a circuit breake
or time delay fuse.
5k~9k 12k~14k 18k 24k~28k 30k, 32k 36k, 38k
0.75 1.0 1.5 2.5 2.5 5.5
Unit(A) Indoor Indoor Indoor Indoor Outdoor Outdoor
Cable Type(B) H05VV-F H05VV-F H05VV-F H05VV-F H05RN-FH05RN-F
NORMAL CROSS
-SECTIONAL AREA
Grade
(mm2)
5 k~9K 1 2k~1 4k 1 8k 2 4k~2 8k
0.75 1.0 1.5 2.5
Cable Type(B) H07RN-F H07RN-F H07RN-F H07RN-F
NORMALCROSS
-SECTIONAL
AREA
Grade
(mm2)
NORMALCROSS-SECTIONALAREA 0.75mm2
30k, 32k 36k, 38k
0.75 0.75
Cable Type(B) H07RN-F H07RN-F
NORMAL CROSS
-SECTIONAL AREA
Grade
(mm2)
7/29/2019 3828A20510D Manual%2CInstallation
20/55
20 Room Air Conditioner
Installation
Outdoor
1. Remove the control cover from the unit byloosening the screw.Connect the wires to the terminals on the
control board individually.2. Secure the cable onto the control board with
the cord clamp.
3. Refix the control cover to the original positionwith the screw.
4. Use a recognized circuit breaker 20A(14k)between the power source and the unit.A disconnecting device to adequatelydisconnect all supply lines must be fitted.
Outdoor Unit
Cover control
Cord clamp
1(L) 2(N) 3 4 1(L) 2(N) 3 4
CASE 1 CASE 2
Connectingcable
7k~14k 18k 24k~28k 30k, 32k 36k, 38k
15 20 30 30 40
CircuitBreaker
(A)
Grade
According to the confirmation of the above conditions, prepare the wiring as follows.
1. Never fail to have an individual power circuit specifically for the air conditioner. As forthe method of wiring, be guided by the circuit diagram posted on the inside of controlcover.
2. The screw which fasten the wiring in the casing of electrical fittings are liable to comeloose from vibrations to which the unit is subjected during the course oftransportation. Check them and make sure that they are all tightly fastened. (If theyare loose, it could cause burn-out of the wires.)
3. Specification of power source.
4. Confirm that electrical capacity is sufficient.5. See to that the starting voltage is maintained at more than 90 percent of the rated
voltage marked on the name plate.
6. Confirm that the cable thickness is as specified in the power source specification.(Particularly note the relation between cable length and thickness.
7. Always install an earth leakage circuit breaker in a wet or moist area.
8. The following would be caused by voltage drop.
Vibration of a magnetic switch, which will damage the contact point, fuse breaking, disturbance of
the normal function of the overload.9. The means for disconnection from a power supply shall be incorporated in the fixed
wiring and have an air gap contact separation of at least 3mm in each active(phase)conductors.
7/29/2019 3828A20510D Manual%2CInstallation
21/55
Installation Manual 21
ENG
LISH
Installation
Checking the Drainage
To check the drainage.
1. Pour a glass of water on the evaporator.
2. Ensure the water flows through the drainhose of the indoor unit without any leakageand goes out the drain exit.
Drain piping
1. The drain hose should point downward foreasy drain flow.
2. Do not make drain piping like the following.
Drain pan
Drainhose
Leakage
checking
Connecting areadrain hose
Leakagechecking
Downward slope
Do not raiseAccumulateddrain water
Tip of drain hosedipped in water
Air
WavingWater
leakage
Water
leakage Ditch
Less than50mm gap
Water
leakage
7/29/2019 3828A20510D Manual%2CInstallation
22/55
22 Room Air Conditioner
Installation
Forming the Piping
Form the piping by wrapping theconnecting portion of the indoor unitwith insulation material and secure it
with two kinds of vinyl tapes. If you want to connect an additional drain
hose, the end of the drain outlet should berouted above the ground. Secure the drainhose appropriately.
In cases where the outdoor unit isinstalled below the indoor unitperform the following.
1. Tape the piping, drain hose and connectingcable from down to up.
2. Secure the tapped piping along the exteriorwall using saddle or equivalent.
In cases where the Outdoor unit isinstalled above the Indoor unitperform the following.
1. Tape the piping and connecting cable fromdown to up.
2. Secure the taped piping along the exteriorwall. Form a trap to prevent water enteringthe room.
3. Fix the piping onto the wall by saddle orequivalent.
Taping
Drain hose
Pipings
Connecting cable
Trap is required to prevent waterfrom entering into electrical parts.
Seal small openingsaround pipings with agum type sealer.
Seal a small opening
around the pipingswith gum type sealer.
Trap
Trap
7/29/2019 3828A20510D Manual%2CInstallation
23/55
Installation Manual 23
ENG
LISH
Installation
Air Purging
Air purging
The air and moisture remaining in the refrigerant system have undesirable effects as indicated below.1. Pressure in the system rises.
2. Operating current rises.3. Cooling(or heating) efficiency drops.4. Moisture in the refrigerant circuit may freeze and block capillary tubing.5. Water may lead to corrosion of parts in the refrigeration system.Therefore, after evacuating the system, take a leak test for the piping and tubing between theindoor and outdoor unit.
Air purging with vacuum pump
1. Preparation
Check that each tube(both liquid and gas side tubes) between the indoor and outdoor units have beenproperly connected and all wiring for the test run has been completed. Remove the service valve capsfrom both the gas and the liquid side on the outdoor unit. Note that both the liquid and the gas sideservice valves on the outdoor unit are kept closed at this stage.
2. Leak test
Connect the manifold valve(with pressure gauges) and dry nitrogen gas cylinder to this service port withcharge hoses.
Be sure to use a manifold valve for air purging. If it is not available, use a stop valve for thispurpose. The "Hi" knob of the manifold valve must always be kept close. Pressurize the system to no more than 150 P.S.I.G. with dry nitrogen gas and close the cylinder
valve when the gauge reading reached 150 P.S.I.G. Next, test for leaks with liquid soap.
To avoid nitrogen entering the refrigerant system in a liquid state, the top of the cylinder must behigher than its bottom when you pressurize the system. Usually, the cylinder is used in a verticalstanding position.
1. Do a leak test of all joints of thetubing(both indoor and outdoor)and both gas and liquid sideservice valves.Bubbles indicate a leak. Be sure towipe off the soap with a cleancloth.
2. After the system is found to be freeof leaks, relieve the nitrogenpressure by loosening the charge
hose connector at the nitrogencylinder. When the system pressureis reduced to normal, disconnectthe hose from the cylinder.
Lo Hi
Indoor unit
Outdoor unit
Manifold valve
Charge hose
Nitrogen gas
cylinder(in verticalstanding position)
Pressuregauge
7/29/2019 3828A20510D Manual%2CInstallation
24/55
24 Room Air Conditioner
Installation
Soap water method
1. Remove the caps from the 2-way and 3-way valves.2. Remove the service-port cap from the 3-way valve.3. To open the 2-way valve turn the valve stem
counterclockwise approximately 90, wait for about
2~3 sec, and close it.4. Apply a soap water or a liquid neutral detergent on
the indoor unit connection or outdoor unitconnections by a soft brush to check for leakage ofthe connecting points of the piping.
5. If bubbles come out, the pipes have leakage
Evacuation
1. Connect the charge hose end described in thepreceding steps to the vacuum pump to
evacuate the tubing and indoor unit.Confirm the "Lo" knob of the manifold valve isopen. Then, run the vacuum pump.The operation time for evacuation varies withtubing length and capacity of the pump. Thefollowing table shows the time required forevacuation.
2. When the desired vacuum is reached, close the"Lo" knob of the manifold valve and stop thevacuum pump.
Finishing the job
1. With a service valve wrench, turn the valve stemof liquid side valve counter-clockwise to fullyopen the valve.
2. Turn the valve stem of gas side valve counter-clockwise to fully open the valve.
3. Loosen the charge hose connected to the gasside service port slightly to release the pressure,then remove the hose.
4. Replace the flare nut and its bonnet on the gasside service port and fasten the flare nutsecurely with an adjustable wrench. Thisprocess is very important to prevent leakage
from the system.5. Replace the valve caps at both gas and liquid
side service valves and fasten them tight.This completes air purging with a vacuum pump.The air conditioner is now ready to test run.
Gas side
Liquid side
CapHexagonal wrench
2-way valve(Open)
3-way valve(Close)
Required time for evacuation when 30 gal/h vacuumpump is used
10 min. or more 15 min. or more
If tubing length is less
than 10m (33 ft)
If tubing length is longer
than 10m (33 ft)
Indoor unit
Outdoor unit
Lo Hi
Manifold valve
Vacuum pump
Pressuregauge
Open Close
7/29/2019 3828A20510D Manual%2CInstallation
25/55
Installation Manual 25
ENG
LISH
Installation
1. Check that all tubing and wiring are properly connected.
2. Check that the gas and liquid side service valves are fully open.
Prepare remote controller1. Remove the battery cover by pulling it
according to the arrow direction.
2. Insert new batteries making sure that the (+)and () of battery are installed correctly.
3. Reattach the cover by pushing it back intoposition.
Use 2 AAA(1.5volt) batteries. Do not userechargeable batteries.
Remove the batteries from the remotecontroller if the system is not used for a longtime.
Settlement of outdoor unit
1. Anchor the outdoor unit with a bolt andnut(10mm) tightly and horizontally on aconcrete or rigid mount.
2. When installing on the wall, roof or rooftop,anchor the mounting base securely with anail or wire assuming the influence of windand earthquake.
3. If the vibration of the unit is transmitted to thehose, secure the unit with an anti-vibrationrubber.
Evaluation of the performance
Operate the unit for 15~20 minutes, then checkthe system refrigerant charge:
1. Measure the pressure of the gas side servicevalve.
2. Measure the temperature of the intake anddischarge of air.
3. Ensure the difference between the intaketemperature and the discharge is more than8C
4. For reference; the gas side pressure ofoptimum condition is as below.(Cooling)
The air conditioner is now ready for use.
NOTICE
Bolt
Tubing connection
Dischargetemperature
Discharge air
Intake temperature
R-22 35C (95F) 4~5kg/cm2G(56.8~71.0 P.S.I.G.)
R-410A 35C (95F) 8.5~9.5kg/cm2G(120~135 P.S.I.G.)
Outside ambientTEMP.
Refrigerant The pressure of the gas sideservice valve.
Test Running
7/29/2019 3828A20510D Manual%2CInstallation
26/55
26 Room Air Conditioner
Installation
If the actual pressure is higher than shown, the system is most likely over-charged, and chargeshould be removed. If the actual pressure are lower than shown, the system is most likelyundercharged, and charge should be added.
NOTICE
PUMP DOWN
This is performed when the unit is relocated or the refrigerant circuit is serviced.
Pump Down means collecting all refrigerant into the outdoor unit without the loss of refrigerant.
Be sure to perform Pump Down procedure in the cooling mode.
Pump Down Procedure
1. Connect a low-pressure gauge manifold hose to the charge port on the gas side service valve.
2. Open the gas side service valve halfway and purge the air in the manifold hose using therefrigerant.
3. Close the liquid side service valve(all the way).
4. Turn on the unit's operating switch and start the cooling operation.
5. When the low-pressure gauge reading becomes 1 to 0.5kg/cm2
G(14.2 to 7.1 P.S.I.G.), fully closethe gas side valve and then quickly turn off the unit. Now Pump Down procedure is completed,and all refrigerant is collected into the outdoor unit.
7/29/2019 3828A20510D Manual%2CInstallation
27/55
ESPAO
L
LG
Aire acondicionadoMANUAL DE INSTALACIN
IMPORTANTE
Lea este manual de instrucciones completamente antes deinstalar el producto.
Cuando el cable de alimentacin est daado, la
sustitucin debe realizarse nicamente por personalautorizado.
El trabajo de instalacin debe realizarse de acuerdo con elReglamento Elctrico nacional y nicamente por personalautorizado.
Despus de leer completamente este manual deinstalacin, gurdelo para futuras consultas.
7/29/2019 3828A20510D Manual%2CInstallation
28/55
2 Aire acondicionado
Aire acondicionado - Manual de instalacin
NDICE
Precauciones de seguridad ....................3
Introduccin...............................................6
Smbolos utilizados en este manual ....6
Caractersticas .......................................6
Instalacin .................................................7
Piezas para la instalacin ......................7Herramientas para la instalacin...........7
Diagrama de instalacin.........................8
Seleccin de la mejor ubicacin............9
Longitud de conductos y elevacin.....10
Fijacin de la placa de instalacin.......11
Taladrado en la pared ..........................11
Trabajo de abocinamiento....................12
Conexin de conductos .......................13
Conexin de cables..............................19
Comprobacin del drenaje...................21
Formacin de conductos .....................22
Purga de aire........................................23
Prueba de funcionamiento...................25
Cuatro tornillos tipo A y tacos deplstico
Cable de conexin
Diagrama gua de instalacin
Conductos: Lado gasLado lquido
Materiales de aislamiento
Conducto adicional de drenaje(Dimetro exterior..................15.5mm)
Dos tornillos tipo B
Indicador de nivel
Destornillador
Taladradora elctrica
Broca corona (70 mm )
Medidor horizontal
Equipo de herramientas de
abocinamiento Llaves dinamomtricas especficas
1,8 kg/m, 4,2 kg/m, 5,5 kg/m, 6,6 kg/m(diferentes en funcin del nmero demodelo)
Llave inglesa semiunin
Un vaso de agua
Destornillador
Llave hexagonal (4 mm)
Detector de fugas de gas
Bomba de vaco
Indicador mltiple
Manual de usuario
Termmetro
Soporte del mando a distancia
Requisitos deinstalacin
Piezas necesarias Herramientas necesarias
7/29/2019 3828A20510D Manual%2CInstallation
29/55
Manual de instalacin 3
ESPAO
L
Precauciones de seguridad
Para evitar lesiones al usuario o a otras personas y daos materiales, debe seguir las siguientes instrucciones.s Lea estas instrucciones antes de instalar el aire acondicionado.s Observe las precauciones especificadas en este manual, ya que incluyen indicaciones importantes
relacionadas con la seguridad.s El uso incorrecto ocasionado al ignorar las instrucciones puede causar lesiones o daos. La gravedad se
clasifica mediante las siguientes indicaciones.
s A continuacin se muestran los significados de los smbolos utilizados en este manual.
ADVERTENCIA
ATENCIN
Este smbolo indica la posibilidad de muerte o lesiones graves.
Este smbolo indica la posibilidad de lesiones o daos materiales.
ADVERTENCIA
s Instalacin
No lo haga.
Siga las instrucciones.
Precauciones de seguridad
Realice siempre la conexinde la toma de tierra.
Si no lo hace, podraproducirse una descargaelctrica.
No utilice un cable dealimentacin, una clavija o unenchufe flojo que estndaados.
Si lo hace, podra producirseun incendio o descargaelctrica.
Para la instalacin del producto,pngase siempre en contactocon el centro de servicio
tcnico o con una empresa deinstalaciones especializada.
De lo contrario, podraproducirse un incendio,descarga elctrica, explosino daos.
Ajuste firmemente lacubierta de la parte elctricaen la unidad interior y elpanel de servicio en launidad exterior.
Si la cubierta de la parte elctricade la unidad interior y el panel deservicio de la unidad exterior noestn ajustados firmemente,
podra producirse un incendio odescarga elctrica debido al polvo,agua, etc.
Instale siempre un interruptordiferencial para el aireacondicionado y el cuadro demaniobra correspondiente.
Si no lo instala, podraproducirse un incendio y unadescarga elctrica.
No almacene ni utilicegases inflamables ocombustibles cerca del aireacondicionado.
De lo contrario, podraproducirse un incendio o unaavera del aparato.
7/29/2019 3828A20510D Manual%2CInstallation
30/55
4 Aire acondicionado
Precauciones de seguridad
Si es necesario desenchufar el cablede alimentacin, hgalo sujetando la
cabeza de la clavija y no lo toquecon las manos hmedas.
De lo contrario, podraproducirse un incendio o unadescarga elctrica.
No utilice el cable dealimentacin cerca de
generadores de calor.
Si lo hace, podra producirseun incendio o una descargaelctrica.
No abra la entrada deaspiracin de la unidad
interior/exterior durante elfuncionamiento.
Si lo hace, podra producirseuna descarga elctrica y unaavera.
No permita que entre aguaen las partes elctricas.
De lo contrario, podra producirseuna avera en la unidad o unadescarga elctrica.
Sujete la clavija por lacabeza cuando la saque.
Podra producirse unadescarga elctrica y daos.
No toque nunca las partesmetlicas de la unidad
cuando retire el filtro. Son afiladas y pueden
producir lesiones.
No comparta el enchufe conotros aparatos.
Podra producirse una descargaelctrica o incendio debido a lageneracin de calor.
No utilice un cable dealimentacin daado.
Si lo hace, podra producirseun incendio o una descargaelctrica.
No modifique ni alargue elcable de alimentacin sincausa justificada.
Si lo hace, podra producirseun incendio o una descargaelctrica.
Tenga cuidado de no estirar
el cable de alimentacindurante el funcionamiento.
Si lo hace, podra producirseun incendio o una descargaelctrica.
Desenchufe la unidad si
emite un sonido extrao,olores o humo.
Si no lo hace, podraproducirse una descargaelctrica o un incendio.
Mantngala alejada de
llamas.
De lo contrario, podraproducirse un incendio.
s Funcionamiento
Asegrese de que el bastidor de instalacinde la unidad exterior no est daado debido aun uso prolongado.
Podra producir daos o un accidente.
No desmonte ni modifique los productos sin
causa justificada.
Podra producirse un incendio o una descargaelctrica.
No instale el aparato en un lugar dondepueda caerse.
De lo contrario, podran producirse daospersonales.
Tenga cuidado cuando lo desembale einstale.
Los bordes afilados pueden producir daos.
7/29/2019 3828A20510D Manual%2CInstallation
31/55
Manual de instalacin 5
ESPAO
L
Precauciones de seguridad
No se suba sobre la unidad interior/exteriorni coloque nada sobre ellas.
Podran producirse daos debido al desplomeo cada de la unidad.
No coloque ningn objeto pesado sobre elcable de alimentacin.
Si lo hace, podra producirse un incendio o unadescarga elctrica.
Si el aparato se ha sumergido en agua,pngase siempre en contacto con el centrode servicio tcnico.
De lo contrario, podra producirse un incendioo una descarga elctrica.
Vigile que los nios no se suban a launidad exterior.
Si lo hacen, podran resultar gravementelesionados debido a una cada.
ATENCINs Instalacin
Instale la manguera de drenaje paraasegurar que el drenaje pueda realizarsecorrectamente.
De lo contrario, podran producirse fugas deagua.
Instale el aparato de modo que el ruido o elaire caliente procedente de la unidadexterior no cause molestias a los vecinos.
De lo contrario, podran producirse disputascon los vecinos.
Evite un enfriamiento excesivo y ventilefrecuentemente.
De lo contrario, podra perjudicar su salud.
Utilice un pao suave para limpiar la unidad. Noutilice cera, disolvente ni un detergente fuerte.
Podra deteriorarse el aspecto del aire acondicionado,
cambiar el color o producirse desperfectos en susuperficie.
No utilice el aparato para una finalidadespecial como el acondicionamiento paraanimales o vegetales, mquinas de precisin ola conservacin de artculos de arte.
Si lo hace, podran producirse daos en suspropiedades.
No coloque ningn obstculo alrededor delas entradas o salidas de aire.
Si lo hace, podra producirse una avera en elaparato o un accidente.
s Funcionamiento
Compruebe siempre si existen prdidas de
gas despus de instalar o reparar la unidad. Si no lo hace, podra producirse una avera en
la unidad.
Instale la unidad bien nivelada.
Si no lo hace, podran producirse vibraciones ofugas de agua.
7/29/2019 3828A20510D Manual%2CInstallation
32/55
6 Aire acondicionado
Introduccin
Este smbolo le avisa del riesgo de descarga elctrica.
Este smbolo le avisa de riesgos que pueden producir daosal aire acondicionado.
Este smbolo indica notas especiales.NOTA
Introduccin
Smbolos utilizados en este manual
Caractersticas
Rejillas de
entrada de aire
Rejillas de
salida de aire
Rejillas de
entrada de aire
Rejillas de
salida de aire
Cables de
conexin
Cables deconexin
ConductosConductos
Manguera
de drenaje Manguera
de drenaje
Placa base Placa base
Receptor de seales
Panel frontal
Entrada de aire
Filtro de aire
7/29/2019 3828A20510D Manual%2CInstallation
33/55
Manual de instalacin 7
ESPAO
L
Instalacin
Tornillo tipo A (6 EA) Tornillo tipo A (8 EA)
Tornillo tipo B Tornillo tipo B
Soporte del mando a distanciaSoporte del mando a distancia
Tipo 1 Tipo 2
Placa de instalacin Placa de instalacin
Figura FiguraNombre
Destornillador
Taladradora elctrica
Cinta mtrica, cuchillo
Broca corona
Llave inglesa
Llave dinamomtrica
Ohmmetro
Llave hexagonal
Ampermetro
Detector de fugas de gas
Termmetro,medidor horizontal
Equipo de herramientasde abocinamiento
Nombre
Piezas para la instalacin
Herramientas para la instalacin
InstalacinLea atentamente y siga las instrucciones paso a paso.
7/29/2019 3828A20510D Manual%2CInstallation
34/55
8 Aire acondicionado
Instalacin
Diagrama de instalacin
Piezas de instalacin que debe comprar ( ).NOTA
Installation plateManguitoCasquillo ManguitoMasilla (sellador para pistola)
Cinta de vinilo (ancha)
Brida
Conducto de gas (Partes opcionales)
Conducto de lquido (Partes opcionales)Conducto de drenaje adicional
Cinta de vinilo (estrecha)
Cable conector(Partes opcionales)
Tuerza el conducto tan cerca dela pared como sea posible, perocon cuidado de que no serompa.
Aplicar despus de realizaruna prueba de drenaje.
Para llevar a cabo la prueba
de drenaje, extraiga los filtrosde aire y vierta agua en elintercambiador de calor.
Deflector vertical de aire
Salida de aire
Botn de funcionamiento forzado
Luces indicadoras de funcionamiento/Receptor de seal
Manguera de desage
Placa de asiento
Orificios de salida de aire
Orificios de entrada de aire
7/29/2019 3828A20510D Manual%2CInstallation
35/55
Manual de instalacin 9
ESPAO
L
Instalacin
Unidad interior
1. No coloque generadores de calor o vapor cerca dela unidad.
2. Seleccione un lugar donde no haya obstculosfrente a la unidad.
3. Asegrese de que el drenaje de condensacinpueda conducirse convenientemente.
4. No instale la unidad cerca de una puerta.5. Asegrese de que el espacio entre la pared y el
lateral izquierdo (o derecho) de la unidad seasuperior a 10 cm. La unidad debe instalarse en lapared a la mayor altura posible, manteniendo unmnimo de 20 cm hasta el techo.
6. Utilice un localizador de pernos para localizarlos yevitar daos innecesarios a la pared.
Unidad exterior
1. Si se coloca un toldo sobre la unidad para evitar laluz solar directa o la exposicin a la lluvia,asegrese de que la radiacin de calor delcondensador no quede restringida.
2. Asegrese de que el espacio alrededor de la parteposterior y los laterales es superior a 30 cm.Delante de la parte frontal de la unidad debe dejarun espacio superior a 70 cm.
3. No coloque animales ni plantas expuestosdirectamente al aire caliente.
4. Tenga en cuenta el peso del aire acondicionado yseleccione un lugar donde se produzca el mnimoruido y vibracin.
5. Seleccione un lugar donde el aire caliente y elruido del aire acondicionado no moleste a losvecinos.
Seleccin de la mejor ubicacin
Ms de 20cm
Ms de
10cm
Ms de 2,3m
Ms de10cm
Instale la unidad interior en la pared a una altura del suelo superior a 2,3 metros.
Ms de30cm
Ms de30cm
Ms de60cm
Ms de60cm
Ms de70cm
7/29/2019 3828A20510D Manual%2CInstallation
36/55
10 Aire acondicionado
Instalacin
Longitud de conductos y elevacin
Unidad exterior
Unidad interior
A
B
Unidad exterior
Unidad interior
A
B
ASeparador de aceite
Unidad exterior
Unidad interiorB
Si la longitud del conducto es superior a 5 m
La capacidad est basada en la longitud estndar y la longitud mxima tolerada est basada enla fiabilidad.El separador de aceite debe instalarse cada 5~7 metros.
7k, 8k, 9k 3/8" 1/4" 7.5 7 15 2011k, 12k, 14k 1/2" 1/4" 7.5 7 15 20
1/2" 1/4" 7.5 15 30 20
18k, 24k, 26k 5/8" 1/4" 7.5 15 30 20
5/8" 3/8" 7.5 15 30 30
Tamao del conductoCapacidad(Btu/h) GAS LQUIDO
Elevacinmxima A (m)
Refrigeranteadicional (g/m)
Elevacinmxima B (m)
Longitudestndar (m)
7/29/2019 3828A20510D Manual%2CInstallation
37/55
Manual de instalacin 11
ESPAO
L
Instalacin
Fijacin de la placa de instalacin
Taladre el agujero del conducto con unabroca corona de 70 mm . Taladre elagujero del conducto, a la derecha oizquierda, ligeramente inclinado hacia ellado exterior.
Taladrado en la pared
5-7mm
(3/16"~5/16")
Interior
PARED
Exterior
La pared que seleccione debe sersuficientemente fuerte y slida para evitarvibraciones.
1. Monte la placa de instalacin en la pared conlos tornillos tipo A. Si monta la unidad en unapared de hormign, utilice pernos de anclaje. Monte la placa de instalacin
horizontalmente alineando la lnea decentros utilizando un nivel.
2. Mida la pared y marque la lnea de centros.Tambin es importante prestar atencin ala localizacin de la placa de instalacin, ya
que el trazado del cableado hacia losenchufes se realiza normalmente por lapared. El taladrado de agujeros en la paredpara las conexiones de los conductos deberealizarse con seguridad.
Gancho delchasis
Placa de instalacin
Tornillo tipo A
Conducto posterior izquierdo Conducto posterior derecho
Placa de instalacin
70mm 70mm
D B
AC
Tornillo tipo 1.
Gancho del
chasis
Placa de instalacin
Tornillo tipo A
Tornillo tipo 2.
Tornillo tipo 1.
Conducto posterior izquierdo Conducto posterior derecho
Placa de instalacin
70mm
133mm
70mm
100mm
Tornillo tipo 2.
A B C D
S4 55 105 65 105SE 70 110 90 110
S5/S8 100 122 240 122
CHASSIS
(Grado)
Distancia (mm)
7/29/2019 3828A20510D Manual%2CInstallation
38/55
12 Aire acondicionado
Instalacin
Trabajo de abocinamiento
La principal causa de las prdidas de gas se debe a defectos en los trabajos de abocinamiento.Realice correctamente el trabajo de abocinamiento mediante el siguiente procedimiento.
Corte los conductos y el cable
1. Utilice el equipo de conductos opcional o losconductos comprados.
2. Mida la distancia entre la unidad interior y launidad exterior.
3. Corte los conductos con una longitud un pocosuperior a la longitud medida.
4. Corte el cable 1,5 m ms largo que la longituddel conducto.
Eliminacin de rebabas1. Elimine completamente todas las rebabas de laseccin transversal de corte del conducto/tubo.
2. Para evitar la cada de rebabas en el interior dela tubera, coloque el extremo delconducto/tubo de cobre hacia abajo y eliminelas rebabas.
Colocacin de la tuerca
Retire las tuercas de abocinamientoincorporadas a la unidad interior y exterior, y acontinuacin, colquelas en el conducto/tubodespus de haber eliminado completamente lasrebabas. (No es posible colocarlas despus deltrabajo de abocinamiento)
Trabajo de abocinamiento
1. Sujete firmemente el conducto de cobre en unahilera segn las dimensiones mostradas en latabla siguiente.
2. Realice el trabajo de abocinamiento con lasherramientas de abocinamiento.
Conductode cobre 90 Inclinado Irregular Rugoso
Conducto
Escariador
Hacia abajo
Tuerca de abocinamiento
Tubo de cobre
mm pulgadas mm6,35 1/4" 1,1~1,39,52 3/8" 1,5~1,712,7 1/2" 1,6~1,815,88 5/8" 1,6~1,819,05 3/4" 1,9~2,1
Dimetro exterior A
Barra
Conducto de cobre
Manivela de aprieteMarca de flecha roja
Cono
Yugo
Manivela
Barra"A"
7/29/2019 3828A20510D Manual%2CInstallation
39/55
Manual de instalacin 13
ESPAO
L
Instalacin
Comprobacin1. Compare el trabajo de abocinamiento con la
figura.
2. Si una seccin abocinada es defectuosa,crtela y realice de nuevo el trabajo de
abocinamiento.
Interior
1. Prepare el conducto y la manguera dedrenaje de la unidad interior para suinstalacin a travs de la pared.
2. Retire el dispositivo de retencin de plsticode las tuberas (consulte la ilustracin) ysaque la tubera y la manguera de drenajedel chasis.
3. Vuelva a colocar en la posicin original soloel soporte 1 de conductos de plstico, no elsoporte 2.
1. Dirija la tubera y la manguera de drenaje de launidad interior hacia la parte posterior derecha.
2. Inserte el cable de conexin en la unidadinterior desde la unidad exterior a travs delagujero del conducto. No conecte el cable a la unidad interior. Realice un pequeo bucle con el cable para
una conexin posterior ms fcil.3. Encinte las tuberas, manguera de drenaje y el
cable de conexin. Asegrese de que lamanguera de drenaje est situada en la parteinferior del conjunto. Si se coloca en la partesuperior es posible que el depsito de drenajese derrame en el interior de la unidad.
Si la manguera de drenaje es conducida porel interior de la habitacin, asle la mangueracon un material de aislamiento* de modo queel goteo de exudacin (condensacin) nodae el mobiliario ni el suelo. Se recomienda espuma de polietileno o
similar.
Inclinado
Interior pulido sin rayas
Liso todo alrededor
Longitud uniforme todo alrededor
Superficiedaada
Roto Espesordesigual
= Abocinamiento incorrecto =
Conexin de conductos
Salida posterior derecha del conducto
Manguerade drenaje
Conductosde conexin
Cable de conexin
Cinta
Manguerade drenaje
7/29/2019 3828A20510D Manual%2CInstallation
40/55
14 Aire acondicionado
Instalacin
4. Instalacin de la unidad interiorCuelgue la unidad interior sobre la parte superior de laplaca de instalacin. (Haga coincidir los dos ganchos de laparte superior posterior de la unidad interior con la partesuperior de la placa de instalacin). Asegrese de que losganchos estn fijados adecuadamente sobre la placa de
instalacin movindola a derecha e izquierda.
Presione la parte inferior derecha e izquierda de la unidadcontra la placa de instalacin hasta que los enganches seajusten en sus ranuras (hasta que hagan clic).
Conexin de los conductos a la unidadinterior y de la manguera de drenaje alconducto de drenaje
1. Alinee el centro de los conductos y apriete
suficientemente la tuerca de abocinamiento amano.
2. Apriete la tuerca de abocinamiento con unallave de tuercas.
3. Cuando extienda la manguera de drenaje enla unidad interior, instale el conducto dedrenaje.
Envuelva con material de aislamiento eltramo de conexin.
1. Solape el material de aislamiento del conducto deconexin y el material de aislamiento del conducto
de la unidad interior. Encinte el conjunto con cintade vinilo de modo que no queden huecos.
2. Encinte el rea que alberga la seccin posterior delalojamiento de los conductos con cinta de vinilo.
3. Encinte suficientemente el conjunto de los
conductos y la manguera de drenaje concinta de vinilo para cubrirlo en el punto enque entran en la seccin posterior delalojamiento de los conductos.
Manguerade drenaje
Cable deconexin
Tubera de launidad interiorTuerca deabocinamiento
Conductos
Llave detuercas
Tubera de la
Llave de boca (fija)
Conductode conexin
Tuerca deabocinamiento
mm pulgadas kgf.m6,35 1/4" 1,8~2,59,52 3/8" 3,4~4,212,7 1/2" 5,5~6,615,88 5/8" 6,3~8,2
Dimetro exterior Apriete
Cinta de vinilo (estrecha)Adhesivo
Conducto de drenaje
Manguera de drenajede la unidad interior
Bandas plsticas Material aislante
Cinta de vinilo(estrecha)
Conducto deconexin
Cable de conexin
Cinta de vinilo(ancha)
Encinte con cinta de vinilo
Conducto dela unidad interior
Conducto
Encinte con cinta de vinilo
Manguera de drenaje
Conducto
Cinta de vinilo (ancha)
7/29/2019 3828A20510D Manual%2CInstallation
41/55
Manual de instalacin 15
ESPAO
L
Instalacin
1. Dirija la tubera y la manguera de drenaje de launidad interior hacia la posicin del agujero deconductos.
2. Inserte los conductos, la manguera de drenaje y el
cable de conexin en el agujero de conductos.3. Inserte el cable de conexin en la unidad interior.
No conecte el cable a la unidad interior. Realice un pequeo bucle con el cable para una
conexin posterior ms fcil.
4. Encinte la manguera de drenaje y el cable deconexin.
5. Instalacin de la unidad interior Cuelgue la unidad interior sobre la parte
superior de la placa de instalacin.Inserte el espaciador, etc. entre la unidad
interior y la placa de instalacin y separe laparte inferior de la unidad interior de la pared.
Conexin de los conductos a la unidadinterior y de la manguera de drenaje alconducto de drenaje.1. Alinee el centro de los conductos y apriete
suficientemente la tuerca de abocinamiento amano.
2. Apriete la tuerca de abocinamiento con una
llave de tuercas.
3. Cuando extienda la manguera de drenaje enla unidad interior, instale el conducto de
drenaje.
Salida posterior izquierda del conducto
Manguerade drenaje
Cable deconexin
1 2
Placa de instalacin
Espaciador
Unidad interior
8cm
Tubera de launidad interior
Tuerca deabocinamiento
Conductos
Llave detuercas
Tubera de launidad interior
Llave de boca (fija)
Conductode conexin
Tuerca deabocinamiento
Cinta de vinilo (estrecha)Adhesivo
Conducto de drenaje
Manguera de drenajede la unidad interior
mm pulgadas kgf.m6,35 1/4" 1,8~2,59,52 3/8" 3,4~4,212,7 1/2" 5,5~6,615,88 5/8" 6,3~8,2
Dimetro exterior Apriete
7/29/2019 3828A20510D Manual%2CInstallation
42/55
16 Aire acondicionado
Instalacin
Envuelva con material de aislamiento eltramo de conexin.1. Solape el aislamiento trmico del conducto de
conexin y el material de aislamiento trmico delconducto de la unidad interior. Encinte el conjuntocon cinta de vinilo de modo que no queden huecos.
2. Encinte el rea que alberga la seccin posterior delalojamiento de los conductos con cinta de vinilo.
3. Encinte el conjunto de los conductos y la manguera
de drenaje con cinta de tela en el tramo en queentra en la seccin posterior del alojamiento de losconductos.
Redirija los conductos y la manguera de
drenaje hacia la parte posterior del chasis.
Instalacin de la unidad interior1. Retire el espaciador.
2. Asegrese de que los ganchos estn fijadosadecuadamente sobre la placa de instalacinmovindola a derecha e izquierda.
3. Presione la parte inferior derecha e izquierdade la unidad contra la placa de instalacinhasta que los enganches se ajusten en susranuras (hasta que hagan clic).
Bandas plsticas Material aislante
Cinta de vinilo (estrecha)
Conductode conexin
Cable de conexin
Conducto dela unidad interi
Conducto
Cinta de vinilo(ancha)
Encinte con cinta de vinilo
Manguera dedrenaje Cinta de
vinilo (estrecha)
Conducto
Encinte con cintade vinilo (ancha)
Conductos que atraviesan elagujero de conductos
Manguerade drenaje
Cable deconexin
7/29/2019 3828A20510D Manual%2CInstallation
43/55
Manual de instalacin 17
ESPAO
L
Instalacin
Informacin de instalacin para conductos a la izquierda.Siga las siguientes instrucciones.
Correcto
Presione sobre la parte superior de la abrazadera y desdoble suavemente las tuberas hacia abajo.
Incorrecto
Si realiza giros a derecha e izquierda puede ocasionar daos a las tuberas.
7/29/2019 3828A20510D Manual%2CInstallation
44/55
18 Aire acondicionado
Instalacin
Exterior
Alinee el centro de los conductos y aprietesuficientemente la tuerca de abocinamiento amano.
Finalmente, apriete la tuerca de abocinamientocon una llave dinamomtrica hasta el tope de la
llave. Cuando apriete la tuerca de abocinamiento
con la llave dinamomtrica, asegrese de quela direccin de apriete es la indicada por laflecha de la llave.
Unidad exterior
Conducto del lado lquido(dimetro menor)
Conductodel lado gas(dimetromayor)
Llave dinamomtrica
mm pulgadas kgf.m6,35 1/4" 1,8~2,59,52 3/8" 3,4~4,2
12,7 1/2" 5,5~6,615,88 5/8" 6,3~8,219,05 3/4" 9,9~12,1
Dimetro exterior Apriete
7/29/2019 3828A20510D Manual%2CInstallation
45/55
Manual de instalacin 19
ESPAO
L
Instalacin
Interior
Conecte el cable a la unidad interior conectado cada cable al terminal correspondiente del panel decontrol de acuerdo con la conexin de la unidad exterior. (Asegrese de que el color de los cables
de la unidad exterior y el nmero de terminal son los mismos que en la unidad interior).
Conexin de cables
El esquema del circuito anterior est sujeto a cambios sin previo aviso. El cable de toma de tierra debe ser ms largo que el resto de los cables.
Cuando realice la instalacin, consulte el esquema del circuito situado detrs del panel frontalde la unidad interior.
Conecte firmemente los cables de manera que no puedan estirarse y sacarse fcilmente.
Conecte los cables de acuerdo con el cdigo de color consultando el esquema de cableado.
Si no utiliza una clavija, instale un interruptorautomtico entre la fuente de alimentacin y launidad, como se muestra.
El cable de conexin conectado a la unidad A debe seleccionarse de acuerdo con las siguientesespecificaciones (tipo B aprobado por HAR o SAA).
El cable de conexin de alimentacin que conecta las unidades interior y exterior debeseleccionarse de acuerdo con las siguientes especificaciones (tipo B aprobado por HAR o SAA).
Aireacondicionado
Fuente de alimentacin principal
Circuit BreakerUse a circuit breakeor time delay fuse.
5k~9k 12k~14k 18k 24k~28k 30k, 32k 36k, 38k
0,75 1,0 1,5 2,5 2,5 5,5
Unidad (A) Interior Interior Interior Interior Exterior Exterior
Tipo de cable (B) H05VV-F H05VV-F H05VV-F H05VV-F H05RN-FH05RN-F
SECCIN
Grado
(mm2)
5 k~9K 1 2k~1 4k 1 8k 2 4k~2 8k
0,75 1,0 1,5 2,5
Tipo de cable (B) H07RN-F H07RN-F H07RN-F H07RN-F
SECCINGrado
(mm2)
SECCIN 0,75mm2
30k, 32k 36k, 38k
0,75 0,75
Tipo de cable (B) H07RN-F H07RN-F
SECCINGrado
(mm2)
7/29/2019 3828A20510D Manual%2CInstallation
46/55
20 Aire acondicionado
Instalacin
Exterior
1. Retire la tapa del panel de control de launidad aflojando el tornillo.Conecte cada cable al terminal
correspondiente del panel de control.2. Fije el cable en el panel de control con la
abrazadera.3. Vuelva a fijar la tapa del panel de control en
su posicin original con el tornillo.4. Utilice un interruptor automtico homologado
de 20A (14K) entre la fuente de alimentaciny la unidad.Debe instalarse un dispositivo dedesconexin que desconecte adecuadamentetodas las lneas de alimentacin.
Unidad exterior
Tapa del panel de control
Abrazadera del cable
1(L) 2(N) 3 4 1(L) 2(N) 3 4
CASO 1 CASO 2
Cable de conexin
7k~14k 18k 24k~28k 30k, 32k 36k, 38k
15 20 30 30 40
Interruptorautomtico
(A)
Grado
Despus de confirmar las condiciones anteriores, prepare el cableado
como se indica a continuacin.1. Disponga siempre de un circuito de alimentacin individual para el aire acondicionado.
Para el mtodo de cableado, guese por el esquema del circuito situado en el interior de la
tapa del panel de control.
2. Los tornillos de apriete del cableado situados en la caja de conexiones elctricas pueden
aflojarse debido a las vibraciones que puede sufrir la unidad durante su transporte.
Comprubelos y asegrese de que estn firmemente apretados. (Si estn flojos, los cablespodran quemarse).
3. Especificacin de la fuente de alimentacin.
4. Confirme que la capacidad elctrica es suficiente.5. Verifique que el voltaje de arranque se mantiene a ms del 90% del voltaje nominal
indicado en la placa de caractersticas.
6. Confirme que la seccin del cable es la especificada en la especificacin de la fuente dealimentacin. (Tenga en cuenta especialmente la relacin entre la longitud del cable y su
seccin).
7. En entornos hmedos o mojados, instale siempre un interruptor diferencial.
8. Una cada de voltaje puede producir lo siguiente:
Vibracin del interruptor magntico que puede producir daos en el punto de contacto, fusindel fusible y trastornos de la funcin normal de sobrecarga.
9. Los medios para la desconexin de una fuente de alimentacin pueden incorporarse en el
cableado fijo y deben tener una separacin de contacto en aire de al menos 3 mm en cada
conductor activo (fase).
7/29/2019 3828A20510D Manual%2CInstallation
47/55
Manual de instalacin 21
ESPAO
L
Instalacin
Comprobacin del drenaje
Para comprobar el drenaje
1. Vierta un vaso de agua en el evaporador.
2. Asegrese de que el agua fluye a travs dela manguera de drenaje de la unidad interiorsin ninguna fuga y que sale por la salida dedrenaje.
Conductos de drenaje
1. La manguera de drenaje debe dirigirse haciaabajo para facilitar el drenaje.
2. No instale el conducto de drenaje como seindica.
Depsitode drenaje
Comprobacin
de fugas
rea de conexin de la
manguera de drenaje
Comprobacinde fugas
Manguerade drenaje
Inclinacin hacia abajo
No lo levanteAgua de drenajeacumulada Extremo de la
manguerade drenajesumergido en agua
Aire
OndulacionesFugade agua
Fugade agua
Canal
Espacio inferiora 50 mm
Fugade agua
7/29/2019 3828A20510D Manual%2CInstallation
48/55
22 Aire acondicionado
Instalacin
Formacin de conductos
Forme los conductos encintando eltramo de conexin de la unidad interiorcon material de aislamiento y asegrelos
con dos tipos de cinta de vinilo. Si desea conectar una manguera de drenaje
adicional, el extremo de la salida de drenajedebe dirigirse hacia el suelo. Sujete lamanguera de drenaje adecuadamente.
Cuando la unidad exterior se instalapor debajo de la unidad interior hagalo siguiente.
1. Encinte los conductos, la manguera dedrenaje y el cable de conexin desde abajohasta arriba.
2. Sujete los conductos encintados a lo largo dela pared exterior utilizando placas de apoyo oequivalentes.
Cuando la unidad exterior se instala
por encima de la unidad interiorhaga lo siguiente.
1. Encinte los conductos y el cable de conexindesde abajo hasta arriba.
2. Sujete los conductos encintados a lo largo dela pared exterior. Forme un sifn para evitarla entrada de agua en la habitacin.
3. Fije los conductos a la pared utilizandoplacas de apoyo o equivalentes.
Encintado
Manguerade drenaje
Conductos
Cable de conexin
Es necesario envolver para evitarque entre agua en las partes elctricas.
Selle las pequeasaberturas alrededor de losconductos con un selladortipo goma.
Sifn
Sifn
Selle las pequeas
aberturas alrededor de losconductos con un selladortipo goma.
7/29/2019 3828A20510D Manual%2CInstallation
49/55
Manual de instalacin 23
ESPAO
L
Instalacin
Purga de aire
Purga de aire
El aire y la humedad remanentes en el sistema refrigerante tienen los siguientes efectos indeseables.1. Se incrementa la presin en el sistema.
2. Se incrementa el consumo elctrico.3. Disminuye la eficacia del enfriamiento (o calentamiento).4. La humedad en el circuito refrigerante puede congelarse y bloquear los tubos capilares.5. El agua puede ocasionar corrosin de piezas del sistema de refrigeracin.Por lo tanto, despus de vaciar el sistema, realice una prueba de fugas en los conductos ytuberas entre la unidad interior y exterior.
Purga de aire con bomba de vaco1. Preparacin
Compruebe que cada tubo (tanto del lado gas como del lado lquido) entre la unidad interior y exterior seha conectado adecuadamente y que se ha completado todo el cableado para la ejecucin de la prueba.
Retire las tapas de las vlvulas de servicio del lado gas y del lado lquido de la unidad exterior. Tenga encuenta que las vlvulas de servicio del lado gas y del lado lquido de la unidad exterior se mantienencerradas en esta etapa.
2. Prueba de fugas
Conecte la vlvula mltiple (con manmetros) y el cilindro de gas de nitrgeno seco a su puerto de serviciocon mangueras de carga.
Asegrese de utilizar una vlvula mltiple para la purga de aire. Si no dispone de ella, utilice para este finuna vlvula de retencin. La palanca Hi de la vlvula mltiple siempre debe permanecer cerrada. No presurice el sistema a ms de 150 P.S.I.G. con gas nitrgeno seco y cierre la vlvula del cilindro cuando
la lectura del manmetro alcance 150 P.S.I.G. A continuacin, compruebe las fugas con lquido jabonoso.
Para evitar la entrada de nitrgeno en estado lquido en el sistema refrigerante, cuando presurice elsistema, el cilindro debe estar en posicin vertical con la vlvula hacia arriba. Normalmente, el cilindro seutiliza en posicin vertical.
1. Realice una prueba de fugas en todas
las juntas de las tuberas (interior yexterior) y en las vlvulas de serviciodel lado gas y del lado lquido.Las burbujas indican una fuga. Eliminetotalmente el jabn con un pao seco.
2. Cuando compruebe que el sistemaest libre de fugas, libere la presin denitrgeno aflojando el conector de lamanguera de carga en el cilindro denitrgeno. Cuando la presin delsistema se reduzca a la normal,desconecte la manguera del cilindro.
Lo Hi
Unidad interior
Unidad exterior
Vlvula mltiple
Manguera decarga
Cilindro de gas
nitr
geno(posicin vertical)
Manmetro
7/29/2019 3828A20510D Manual%2CInstallation
50/55
24 Aire acondicionado
Instalacin
Mtodo del agua jabonosa1. Retire las tapas de las vlvulas de dos vas y tres vas.2. Retire la tapa del puerto de servicio de la vlvula de 3 vas.3. Para abrir la vlvula de 2 vas, gire el vstago de la vlvula
en sentido contrario a las agujas del reloj aproximadamente
90, espere entre 2 y 3 segundos y cirrela.4. Aplique agua jabonosa o un detergente neutro lquido en la
conexin de la unidad interior o en las conexiones de launidad exterior con un cepillo suave para comprobar lasfugas de los puntos de conexin de los conductos.
5. Si hay burbujas, los conductos tienen fugas.
Vaciado1. Conecte el extremo de la manguera de carga, como se
describe en los pasos anteriores, a la bomba de vac o paravaciar las tuberas y la unidad interior. Confirme que lapalanca Lo de la vlvula mltiple est abierta. Acontinuacin, ponga en marcha la bomba de vaco. La
duracin de la operacin de vaciado vara en funcin de lalongitud de las tuberas y la capacidad de la bomba. Lasiguiente tabla muestra el tiempo necesario para el vaciado.
2. Cuando se alcance el vaco deseado, cierre la palanca Lode la vlvula mltiple y detenga la bomba de vaco.
Finalizacin de la tarea1. Con una llave para vlvula de servicio, gire el vstago de la
vlvula del lado lquido en sentido contrario a las agujas del
reloj para abrirla completamente.2. Gire el vstago de la vlvula del lado gas en sentido
contrario a las agujas del reloj para abrirla completamente.
3. Afloje suavemente la manguera de carga conectada alpuerto de servicio del lado gas para liberar la presin y, acontinuacin, retire la manguera.
4. Vuelva a colocar la tuerca de abocinamiento y susombrerete en el puerto de servicio del lado gas y apriete
firmemente la tuerca de abocinamiento con una llaveajustable. Este proceso es muy importante para evitar fugasen el sistema.
5. Vuelva a colocar las tapas de las vlvulas en las vlvulas de
servicio del lado gas y del lado lquido y apritelas
firmemente.Esto completa la purga de aire con una bomba de vaco. El
aire acondicionado est ahora preparado para una prueba defuncionamiento.
Lado gas
Lado gasLlave hexagonal
Vlvula de 2 vas(abierta)
Vlvula de 3 vas(cerrada)
Lado lquido
Tiempo necesario para el vaciado cuando se utilizauna bomba de aproximadamente 115 l/h.
10 minutos o ms 15 minutos o ms
Si la longitud de la tuberaes inferior a 10 m
Si la longitud de la tuberaes superior a 10 m
Unidad interior
Unidad exterior
Lo Hi
Vlvula mltiple
Bomba de vaco
Manmetro
Abierto Cerrado
7/29/2019 3828A20510D Manual%2CInstallation
51/55
Manual de instalacin 25
ESPAO
L
Instalacin
1. Compruebe que todas las tuberas y cables estn conectados correctamente.
2. Compruebe que las vlvulas de servicio del lado gas y del lado lquido estn completamente abiertas.
Preparacin del mando a distancia
1. Retire la tapa de las pilas estirando en ladireccin de la flecha.
2. Inserte pilas nuevas asegurndose de que losextremos (+) y (-) de las pilas estn colocadoscorrectamente.
3. Vuelva a colocar la tapa empujndola hasta suposicin.
Utilice 2 pilas AAA (1,5 volt). No utilice pilasrecargables. Retire las pilas del mando a distancia si el
sistema no va a utilizarse durante un largoperiodo de tiempo.
Posicionamiento de la unidad interior
1. Ancle horizontal y firmemente la unidad exteriorcon un tornillo y una tuerca (10 mm ) sobre unsoporte rgido o de hormign.
2. Cuando la instale en una pared, techo o tejado,sujete firmemente la base de montaje con unanclaje o cable teniendo en cuenta la influenciadel viento y los terremotos.
3. Si la vibracin de la unidad se trasmite a lamanguera, asegure la unidad con gomaantivibracin.
Evaluacin del rendimientoPonga en marcha la unidad durante 15~20 minutos
y, a continuacin, compruebe la carga del sistemarefrigerante:1. Mida la presin de la vlvula de servicio del lado
gas.2. Mida la temperatura de entrada y descarga de
aire.3. Compruebe que la diferencia entre la temperatura
de entrada y de descarga es superior a 8C.4. Como referencia; la presin del lado gas en
condiciones ptimas se muestra a continuacin(enfriamiento).
El aire acondicionado est ahora preparado para suutilizacin.
NOTA
Tornillo
Conexin de tuberas
Temperaturade descarga
Descarga de aire
Temperatura de entrada
R-22 35C (95F) 4~5kg/cm2G(56,8~71,0 P.S.I.G.)
R-410A 35C (95F) 8,5~9,5kg/cm2G(120~135 P.S.I.G.)
Temp. ambienteexterior
Refrigerante Presin de la vlvula de serviciodel lado gas
Prueba de funcionamiento
7/29/2019 3828A20510D Manual%2CInstallation
52/55
26 Aire acondicionado
Instalacin
Si la presin actual es superior a la mostrada, es probable que el sistema est sobrecargado ydebe reducir carga. Si la presin actual es inferior a la mostrada, es probable que el sistema estinfracargado y debe aadir carga.
NOTA
RECOGIDA DE GAS
Se realiza cuando se cambia de lugar la unidad o cuando se ha llevado a cabo elmantenimiento del circuito refrigerante.
Recogida de gas significa recoger todo el refrigerante en la unidad exterior sin prdida derefrigerante.
Asegrese de realizar el procedimiento de recogida de gas en modo de enfriamiento.
Procedimiento de recogida de gas
1. Conecte una manguera colectora con el manmetro de baja presin al puerto de carga de lavlvula de servicio del lado gas.
2. Abra la mitad de la vlvula de servicio del lado gas y purgue el aire en la manguera colectorautilizando el refrigerante.
3. Cierre la vlvula de servicio del lado lquido (completamente).4. Encienda la unidad y ponga en marcha la funcin de enfriamiento.
5. Cuando la lectura del manmetro de baja presin sea de 1 a 0,5 kg/cm2G (14,2 a 7,1 P.S.I.G.),cierre completamente la vlvula del lado gas y, a continuacin, apague rpidamente la unidad.En este momento, el procedimiento de recogida de gas se ha completado y todo el refrigeranteest recogido en la unidad exterior.
7/29/2019 3828A20510D Manual%2CInstallation
53/55
Nota
Manual de instalacin 27
ESPAO
L
7/29/2019 3828A20510D Manual%2CInstallation
54/55
28 Aire acondicionado
Nota
7/29/2019 3828A20510D Manual%2CInstallation
55/55
Recommended