39101.pdf

Euro Hexsert® 39101Steel, Low Profile, Hexagonal Section, Round Bore, Open End

Textron Fastening Systems LimitedMundells, Welwyn Garden City, Hertfordshire AL7 1EZ United KingdomTelephone +44 (0) 1707 668668 Facsimile +44 (0) 1707 338828www.avdel.textron.com

Material

Low carbon steel to BS 970 040A04 SAE 1008

DIN 1654 Qst 34-3

Key Features

• For use in metric hole sizes • Very high torque-to-turn, particularly in soft metals

• Near flush installation • Unlubricated as standard

BEFORE PLACING AFTER PLACING

D i m e n s i o n s in millimetres

Grip Range

min. max.

0.50 2.00

0.50 3.00

3.00 5.50

0.50 3.00

3.00 5.50

0.50 3.00

3.00 5.50

1.00 3.50

Thread Size

M4 x 0.7

M5 x 0.8

M5 x 0.8

M6 x 1.0

M6 x 1.0

M8 x 1.25

M8 x 1.25

M10 x 1.5

Hole Size

6.0

7.0

7.0

9.0

9.0

11.0

11.0

13.0

A

±0.08

5.89

6.89

6.89

8.89

8.89

10.89

10.89

12.89

max.

7.80

9.10

9.10

11.60

11.60

14.20

14.20

16.40

D

±0.13

0.50

0.76

0.76

0.84

0.84

1.03

1.03

1.10

J

max.

9.20

11.20

11.20

13.40

13.40

16.20

16.20

18.50

M

nom.

10.50

12.70

15.20

15.00

17.50

17.50

20.00

20.20

P

max.

6.00

6.80

6.80

10.10

10.10

11.40

11.40

13.20

Part Number

39101-24020

39101-25030

39101-25055

39101-26030

39101-26055

39101-28030

39101-28055

39101-20035

across flats+ 0.1 - 0

Zinc plated,Yellow passivated

B F

±0.08 A/F

5.89

6.89

6.89

8.89

8.89

10.89

10.89

12.89

Thread Sizes

I n s t a l l a t i o n To o l s

M4-M10 M4-M10 M5-M6

742Tool ModelAutosert®

2000 Autosert®

7566

P e r f o r m a n c e D a t a

M4 x 0.7 6.3 1.4 4.2 5.1

M5 x 0.8 8.8 2.6 7.5 7.9

M6 x 1.0 14.4 3.2 10.7 12.4

M8 x 1.25 15.0 4.1 22.7 32.0

M10 x 1.5 19.7 5.2 38.5 45.0

Thread Size Pull-Out Push-Out Torque-To-Turn Maximum Torqueto be applied to bolt

kN kN Nm* Nm**

*Torque-To-Turn These figures represent the minimum torque

applied to cause the fastener to turn in the parent material.

**Maximum Torque These figures represent the

maximum recommended torque to be applied to the bolt,

which will not cause thread distortion or failure in the insert.

Finish

Zinc plated to BS 3382 and yellow

passivated to BS 6338

J = Blind Side Bulb Diameter

M = Overall Length (Unplaced)

P = Blind Side Protrusion

A = Body Diameter (across flats)

B = Lip Diameter

D = Lip Thickness

F = Across Flats of Hex Body

B

M

A

D F

J

GRIPP

ACROSS FLATS

HEXAGONALHOLE

© T

EX

TR

ON

FA

ST

EN

ING

SY

ST

EM

S

MA

Y2

00

2