A Presentation On Printer

A Presentation On

Printer

Department of Computer Engineering,M. S. P. V. L. Polytechnic College,

Pavoorchatram.www.ustudy.in

Introduction

• Printer is an output device.

• This is used to take hard copies of any

computer based application.

www.ustudy.in

Types of printer

• Dot matrix printer

• Ink jet printer

• Laser printer

www.ustudy.in

Dot matrix printer

• In this printer the characters are

formed with the help of dots.

• So this is called dot matrix printer.

www.ustudy.in

Dot matrix printer

www.ustudy.in

Dot matrix printer

www.ustudy.in

Types of Dot matrix printer

• 7-pin printers

• 9-pin printers

• 24-pin printers

www.ustudy.in

Operation of 7-pin printer

• The print head of the dot matrix printer

consists of a column of 7 small needles.

• Each needle can move freely.

www.ustudy.in

Cont.,

www.ustudy.in

Cont.,

• Each needle can be made to print a dot by

means of a hammer action that forced the

needle to come out and press the ribbon

against the paper.

• Standard characters are produced in a 5 x

7 dot matrix. (7 dots high and 5 dots

wide).

www.ustudy.in

5x7 dot matrix

www.ustudy.in

Cont.,

• The characters are printed column by

column and not all at once.

• For example to print the character T,

initially pin number 1 is made to contact

the ribbon.

www.ustudy.in

Cont.,

• Thus first column of the characters is got.

• Then the print head is moved towards right

and once again the pin 1 is made to contact

the ribbon.

• Thus second column of the character is

got. Then the print head is moved to get the

third column and so on.www.ustudy.in

Cont.,

1 2 3 4 5

1234567

www.ustudy.in

Parts of a Dot matrix printer

www.ustudy.in

Block diagram of Dot matrix printer Interface

Connector

Controlelectronics

Driver circuits

Power supplyPower supply

Front panelSwitches and

LED

Front panelSwitches and

LED

LFmechanis

m

LFmechanis

mPrintmechanis

m

Printmechanis

m

Print head

control

Print head

control

Carriage movementcontrol

Carriage movementcontrol

DIP switches

Cooling fan

Print head

Temperaturesensor

Ribbon motor

Home sensor

Carriage motor

Paper sensor

Line feed motor

www.ustudy.in

Dot matrix printer head mechanisms in action:

Classical printhead mechanism is showed from the left side. The permanent magnet printer head mechanism you may see at right. www.ustudy.in

Construction of a Dot matrix printer

Power supply

• Normally printers consist of Switch

Mode Power Supply (SMPS).

• This unit is used to convert the AC

voltage to different DC voltage levels.

www.ustudy.in

To control electronics, driver circuitTo BufferSMPSAC

230 V

+5V-

12V

+24V

To print head, paper feed motor,

Carriage motor

Power supply

www.ustudy.in

Cont.,

Interface connector

• Printers are connected to the computer

through a 36 pin centronics interface

cable or a 9-pin RS 232C serial interface

cable.

• The serial data from the computer is received

and stored in the printers buffer RAM.www.ustudy.in

Centronics Printer connector

www.ustudy.in

RS232 Connector

www.ustudy.in

Cont.,

• The Buffer RAM can store one line to one

page depending on the size of the RAM.

www.ustudy.in

Printer Buffer RAM

www.ustudy.in

Cont.,

Control electronics

• This unit contains an intelligent

processor for controlling the functions of

the printer.

www.ustudy.in

Cont.,

www.ustudy.in

Cont.,

Driver circuit

• This unit is used to control the line feed

mechanism, print mechanism and

ribbon movements.

• These mechanisms use stepper motors.

www.ustudy.in

Driver circuit

www.ustudy.in

Cont.,

• This circuit provides high current for

driving these stepper motors.

• Also it sends feed back signals to control

electronics for monitoring the speed and

displacement of these mechanisms.

www.ustudy.in

Cont.,

Front panel

• This consists of a minimum three status

lights (LED) and three soft touch

switches.

• The lights are used to give information

about the status of the printer to the user.

www.ustudy.in

Front panel

www.ustudy.in

Cont.,

• Switches are used to give the control

commands.

• For example font selection.

www.ustudy.in

Cont.,

DIP switches

• These switches are present in the

interface card and are used to change

the printer settings.

www.ustudy.in

DIP switches

www.ustudy.in

Printer setting change

The settings that can be changed are

• Printing of graphics and accented

characters

• Page length

• Line spacing

www.ustudy.in

Cont.,

• Print quality

• Auto line speed

• Character set for different countries

www.ustudy.in

Sensors

• These are used to keep the printer safe

from abnormal conditions.

www.ustudy.in

Printer sensor

www.ustudy.in

Different Sensors

Home sensor

• This is used to detect whether the head

carriage is in the extreme left margin.

Paper empty sensor

• This is used to signal when there is no

paper in the printer.

www.ustudy.in

Cont.,

Temperature sensor

• This is used to detect the abnormal

timings used to fire the pins.

www.ustudy.in

Cont.,

Print mechanism

• This contains two subsystems

Carriage movement control mechanism

• This moves the carriage bidirectionally by

means of a stepper motor

www.ustudy.in

Carriage movement control mechanism

www.ustudy.in

Cont.,

Ribbon feed mechanism

• This feeds the ribbon when the print head

is printing

www.ustudy.in

Ribbon feed mechanism

www.ustudy.in

Features of Dot matrix printer

• Both text and graphics can be printed

• Printing cost is very low

• Multiple copies can be taken with the help

carbon papers

www.ustudy.in

Cont.,

• By increasing the number of pins from 7

to 9 or 24 the quality of printing can be

increased.

• It’s operating speed is slow.

www.ustudy.in

The End

Thank you!

www.ustudy.in