View
213
Download
1
Category
Preview:
Citation preview
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 36647-38808 (0802) 1 of 11
INSTALLATIONINSTRUCTIONS
Accessory .oN snoitacilbuPnoitacilppA
Issue Date
FEB 2008
2008 RIDGELINEXM RADIO SYSTEMAII 36647-38808
08B15-SJC-1A00-91
PARTS LIST
Attachment Kit:P/N 08B15-SJC-100A
2 XM tuner bracket
Bus cable
Wire tie with clip
21 Wire ties
3 EPT sealers
Cushion tape
4 Flange nuts, 6 mm
4 Washer-screws, 5 x 8 mm
4 Washer-bolts, 6 x 16 mm
XM Antenna (sold separately):P/N 08A15-0J1-100
Antenna
XM Tuner (sold separately):P/N 08A15-3J1-000
XM tuner
TOOLS AND SUPPLIES REQUIREDPhillips screwdriverFlat-tip screwdriver10 mm Combination wrenchRatchet8 and 10 mm SocketIsopropyl alcoholShop towelTape measureScissorsFelt-tip penTORX wrench
www.collegehillshonda.com
2 of 11 ©)2080( 48043-95423 IIA 2008 American Honda Motor Co., Inc. - All Rights Reserved.
4703032T
4703023T
6421180B 4. Pull away the weatherstrip from aroundpassenger’s A-pillar. Remove the passenger’s A-pillar trim (two clips).
Illustration of the XM Radio Installed on theVehicle
Customer Information: The information in thisinstallation instruction is intended for use only byskilled technicians who have the proper tools,equipment, and training to correctly and safely addequipment to your vehicle. These proceduresshould not be attempted by “do-it-yourselfers.”
INSTALLATION
1. Make sure you have the anti-theft code for theradio, then write down the radio station presets.
2. Disconnect the negative cable from the battery.
ANTENNA
XM TUNER
BUSCABLE
AUDIOUNIT
3. Remove the passenger’s front grab rail:
• Remove the screw covers (two retaining tabsfor each cover).
• Remove the two screws, and remove thepassenger’s grab rail.
PASSENGER’SGRAB RAIL
SCREWCOVER
SCREW
RETAININGTAB
RETAININGTAB
SCREWSCREWCOVER
WEATHERSTRIP(Pull away.)
2 CLIPS PASSENGER’SA-PILLAR TRIM
www.collegehillshonda.com
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 36647-38808 (0802) 3 of 11
4703231T
3915102T
3916011T
5. Remove the right sunvisor screw cover (fourretaining tabs), and remove the right sunvisor(two TORX screws, and unplug the vehicleconnector).
6. Open the glove box. Remove the left and rightstops from the glove box by releasing the retainingtabs.
7. Remove the left dashboard side cover (sevenclips).
8. Insert a flat-tip screwdriver wrapped with a shoptowel into the groove of the instrument panel andrelease the two clips. Pull the instrument panel outtoward you to release the eighteen clips, andremove the instrument panel by unplugging thevehicle connectors.
4703051T
RIGHTSUNVISOR
TORX SCREWS(T25)
SCREWCOVER
4 RETAININGTABS
VEHICLE 2-PINCONNECTOR
LEFTDASHBOARDSIDE COVER
2 STOPS
2 RETAININGTABS
RIGHTSTOPPERLEFT
STOPPER
GLOVE BOX
GLOVE BOX
VEHICLECONNECTORS
VEHICLECONNECTORS
INSTRUMENTPANEL
18 CLIPS
VEHICLECONNECTOR SHOP
TOWEL
FLAT-TIP SCREWDRIVERS(Insert into the groove.)
2 CLIPS
7 CLIPS
www.collegehillshonda.com
4 of 11 ©)2080( 88038-74663 IIA 2008 American Honda Motor Co., Inc. - All Rights Reserved.
3916042T
3916021T
4606030T
9. Remove the meter assembly (four self-tappingscrews, and unplug the three vehicle connectors).
11. Remove the driver’s dashboard under cover:
• Remove the one self-tapping screw.
• Release the nine clips, and pull out on thedriver’s dashboard under cover.
• Unplug the vehicle connectors, and removethe vehicle tube. Remove the driver’sdashboard under cover.
12. Remove the fuel fill door release handle. Removethe left front door sill trim (three clips and threeretaining tabs).
AUDIOUNIT
5 BOLTS
INSTRUMENTPANELVEHICLE
CONNECTORS DRIVER’S DASHBOARDUNDER COVER
9 CLIPS
SELF-TAPPINGSCREW
VEHICLECONNECTOR
VEHICLETUBE
VEHICLE CONNECTOR(If equipped.)
10. Remove the audio unit (five bolts, pull the audiounit out towards you, and unplug the vehicleconnectors).
4703042T
SELF-TAPPINGSCREWS
METERASSEMBLY
VEHICLECONNECTORS
RETAININGTABS
RETAINING TABLEFT FRONTDOOR SILL TRIM
CLIP
FRONT
FUEL FILL DOORRELEASE HANDLE
CLIP
www.collegehillshonda.com
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 36647-38808 (0802) 5 of 11
4703062T
3916050T
14. Remove the driver’s seat frame rear cover (twoclips and two hooks).
4713010K
DRIVER’SSEAT
DRIVER’S SEAT FRAMEREAR COVER
2 CLIPS
2 HOOKS
Installing the Antenna
15. Using isopropyl alcohol on a shop towel, cleanthe right front upper corner on the inside of thefront window. Remove the four adhesive backingsfrom the antenna, and attach the antenna to thefront window at the location shown. Install theantenna by applying sufficient pressure.
16. Route the antenna harness down the passenger’sA-pillar along the vehicle harness, secure theantenna harness to the vehicle harness withthree wire ties in areas shown.
13. Pull away the weatherstrip from around thedriver’s kick panel. Remove the driver’s kick panel(one screw clip and one clip).
WEATHERSTRIP(Pull away.)
DRIVER’SKICK PANEL
CLIP
SCREWCLIP
4703072T
VEHICLECLIP
VEHICLEHARNESS
ANTENNA
ANTENNAHARNESS
WIRETIE
ANTENNAHARNESS
VEHICLEHARNESS
PASSENGER’SA-PILLAR
10 mm
50 mm
ANTENNA
ANTENNA
4 ADHESIVEBACKINGS
FRONTWINDOW
PASSENGER’SA-PILLAR
BLACKPAINTEDAREA
www.collegehillshonda.com
6 of 11 ©)2080( 80883-95423 IIA 2008 American Honda Motor Co., Inc. - All Rights Reserved.
4703111T
4703101T
4703083T
18. Wrap two EPT sealers around the antennaharness at the locations shown.
19. Route the antenna harness down behind thedashboard and towards the glove box. Secure theantenna harness to the vehicle harness with onewire tie.
20. Inside the glove box opening, route the antennaharness along the vehicle harness and towardsthe driver’s side of the vehicle. Secure theantenna harness to the vehicle harness withthree wire ties in areas shown.
21. Route the antenna harness past the audio unitopening, and secure the antenna harness to thevehicle harness with one wire tie.
WIRETIE
VEHICLEHARNESSVEHICLE
CLIPANTENNAHARNESS
GLOVE BOXOPENING
WIRETIES
VEHICLECLIPS
AUDIO UNITOPENING GLOVE BOX
OPENING
ANTENNAHARNESS VEHICLE
HARNESS
WIRE TIE
17. Using a felt-tip pen, mark the antenna harness atthe point where the harness touches thedashboard.
4703092T
PASSENGER’SA-PILLAR TRIMOPENING
GLOVE BOXOPENING
ANTENNAHARNESS
WIRE TIE
VEHICLEHARNESS
ANTENNAHARNESS
2 EPTSEALERS 50 mm
MARK(Align withthe mark.)
FELT-TIPPEN
DASHBOARD
ANTENNAHARNESS
LONG SIDE
SHORTSIDE
LONG SIDE
EPTSEALER
EPTSEALER
www.collegehillshonda.com
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 36647-38808 (0802) 7 of 11
6421090B
ANTENNAHARNESS
WIRETIES
FRONT
DOOR SILL
WIRETIES
VEHICLEHARNESS
6421070B
WIRE TIE
VEHICLEFRAME
METER ASSEMBLYOPENINGVEHICLE
HARNESS
WIRE TIE
ANTENNAHARNESS
VEHICLEHARNESS
6421080B
ANTENNAHARNESS
WIRETIE
VEHICLEHARNESS
WIRETIES
METER ASSEMBLYOPENING
6421100B
DRIVER’SSEAT
WIRE TIEWITH CLIP
ANTENNAHARNESS
FLOOR CARPETCUTOUT
FLOORCARPET
BUSCABLE
550 mm
380 mm
22. Route the antenna harness as shown andtemporarily secure it to the vehicle harness usingtwo wire ties.
23. Route the antenna harness along the vehicleharness and temporarily secure it to the vehicleharness using four wire ties.
24. Route the antenna harness as shown andtemporarily secure it to the vehicle harness usingfour wire ties.
25. Route the antenna harness and bus cable underthe floor carpet and pull them out of the cutout inthe floor carpet.
26. Adjust the antenna harness and bus cable youjust pulled out of the cutout in the floor carpet tothe length shown.
27. Bind the antenna harness and bus cabletogether in the position shown using a wire tiewith clip.
www.collegehillshonda.com
8 of 11 ©)2080( 88803-74663 IIA 2008 American Honda Motor Co., Inc. - All Rights Reserved.
4703260T
6421130B
DRIVER’SSEAT PIPE
FRONT
CUSHIONTEPE
XM TUNER
XM TUNER
corner
EPTSEALER
6421110B
DRIVER’S SEAT
6 mmFLANGE NUTS
6 x 16 mmWASHER-BOLTS
DRIVER’SSEAT PANEL
XM TUNERBRACKET 6 mm
FLANGE NUTS
XM TUNERBRACKET
6421120B
BUS CABLE14-PINCONNECTOR
ANTENNAHARNESS1-PINCONNECTOR
XM TUNER
WIRE TIEWITH CLIP
XM TUNERBRACKET
FRONT
XM TUNER
XM TUNERBRACKET
5 x 8 mmWASHER-SCREWS
XM TUNERBRACKET
5 x 8 mmWASHER-SCREWS
14-PIN CONNECTORLOCATION
2-PIN CONNECTORLOCATION
Installing the XM Tuner
28. Install the XM tuner brackets to the XM tuner withfour 5 x 8 mm washer-screws.
29. Install the XM tuner brackets to the driver’s seatpanel with four 6 x 16 mm washer-bolts and four 6mm flange nuts.
NOTE: If the vehicle is equipped with seat plate with welded nuts, the four flange nuts are not used.
30. Connect the antenna harness 1-pin connector andbus cable 14-pin connector to the XM tuner.
33. Attach the EPT sealer to the corner of the XMtuner as shown.
31. Install the wire tie with clip, with which you boundthe antenna harness and bus cable together instep 27, on the XM tuner bracket.
32. Using a isopropyl alcohol clean the vehicle panelsurface where the EPT sealer will be attached.Attach the antenna harness cord and bus cablecord to the XM tuner using a cushion tape asshown.
ANTENNAHARNESS
BUS CABLE
www.collegehillshonda.com
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 36647-38808 (0802) 9 of 11
6421140B
FRONT
6421160B
6421150B
WIRETIES
VEHICLEHARNESS
BUSCABLE
ANTENNAHARNESS
WIRETIES
DOOR SILL
WIRETIES
VEHICLEHARNESS
BUSCABLE
ANTENNAHARNESS
METER ASSEMBLYOPENING
WIRETIE
WIRE TIEVEHICLEHARNESS
METER ASSEMBLYOPENING
BUSCABLE
ANTENNAHARNESS
WIRE TIE
VEHICLEHARNESS
VEHICLEFRAME
34. Route the bus cable and antenna harness to thefront side of the car and secure it to the vehicleharness using four wire ties.
35. Route the bus cable and antenna harness to thetop of the car and secure it to the vehicle harnessusing four wire ties.
36. Route the bus cable as shown. Secure the buscable and antenna harness to the vehicle harnessusing two wire ties as shown.
www.collegehillshonda.com
10 of 11 ©)2080( 80883-74663 IIA 2008 American Honda Motor Co., Inc. - All Rights Reserved.
4703240T
VEHICLECONNECTOR BUS CABLE
14-PINCONNECTOR
VEHICLECONNECTORS
AUDIO UNIT
4701131T
AUDIO UNIT INSTRUMENTPANEL
5 BOLTS (Reuse.)
6421170B
With Player
Without Player
4703250T
AUDIO UNIT
PLAYER
BUS CABLE14-PINCONNECTOR
VEHICLECONNECTOR
WIRETIE
VEHICLEHARNESS
AUDIOUNITOPENING
METERASSEMBLYOPENING
VEHICLE 20-PINCONNECTOR
BUSCABLE
BUS CABLE14-PIN CONNECTOR(Align with the vehicle20-pin connector.)
WIRE TIE
ANTENNAHARNESS
Routing the Bus Cable
37. Align the end of the bus cable connector with theend of the vehicle 20-pin connector and securethe bus cable to the vehicle harness using a wiretie.
38. Secure the bus cable and antenna harness to thevehicle harness using a wire tie. Bundle theexcess of the antenna harness and secure it tothe vehicle harness using a wire tie.
39. Plug the bus cable 14-pin connector and vehicleconnectors into the audio unit/player.
WIRE TIE
www.collegehillshonda.com
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 36647-38808 (0802) 11 of 11
4703220T
DRIVER’S SEATCheck that theantenna harness andbus cable are notpulled too tight whenthe seat is movedback and forth.
40. Reinstall the audio unit.41. Slide the driver’s seat back and forth to check
that the antenna harness and bus cable are notpulled too tight or end up too loose.
42. Check that all wire harnesses are routed properlyand all connectors are plugged in.
43. Reconnect the negative cable to the battery.
44. Enter the customer’s radio anti-theft code, andreset the radio station presets.
45. Set the clock.
46. Check the operation of the XM radio systemaccording to the vehicle’s Owner’s Manualsupplied.
47. Reinstall all removed parts.
NOTE: Whenever the battery is disconnected, thedriver’s window AUTO function is disable.
48. Start the engine. Push down on the driver’swindow switch until the window is fully open.
49. Pull up on the driver’s window switch fully to closethe window completely, then hold the switch for 2seconds or more.
50. Test the window AUTO function.
www.collegehillshonda.com
Recommended