View
217
Download
1
Category
Preview:
Citation preview
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
CLASSIC ACOUSTICS AND TOA
PRESENTS THEVENAS VOICE EVACUATION SYSTEM
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
VM-2000VM-2000 VM-2120, VM-2240
Mixer AmplifierMixer Amplifier
Features & Functions
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
INPUTS: 2 BGM Inputs 3 Mic/Line Inputs 1 Telephone Input Remote Microphone Input (for up to 4 RM-200M) 100V Speaker Line Power Amplifier Input
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
OUTPUTS: Speaker Line Outputs:
- 120W: VM-2120, 240W: VM-2240- 100 volts (70 or 50 volt by simple modification)- 1 Direct- 5 Zones (with ON/OFF Switch and Attenuator)- (50V and 70V can be achieved by internal re-wiring)
1 Line Output pre-master 1 Line Output post-master 1 Recording Output
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
5 priority levels are provided:
Emergency: highest priority
4 priority levels (1 - 4)
Remote-Controlled Power-ONthe VM is always in stand-by mode,
to be switched on by external equipment (e.g. central system in emergency case)
Emergency Power (24V DC) Inlet Cascading 9 VM-2000
9 VM-2000 can be combined to obtain up to45 zones and more output power
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
Optional Surveillance Functions:
Monitoring- Speaker Line- Amplifier- CPU- the Communication with Remote Microphone
Failure Indication on Remote Microphone and VM
Optional Voice Message Functions: 7 Messages
- 5 for commercial purpose- 2 for emergency purpose
1 Chime
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
Mic/Line Inputs
BGM Inputs
Master volume
Zone Attenuators
Zone buttons
All-call button
FAULTEMERGENCY
Emergency and Fault Indication LED Level meter
Power switch(stand-by)
Emergency and Fault Indication LEDEmergency and Fault Indication LEDEmergency and Fault Indication LEDEmergency and Fault Indication LED
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
AC mains 24V DCBGM inputs
w. levelLine inputs+ outputs
Voice message module
Mic/lineinputs
Telephone input,
priority control in
Setting DIPswitches
Control I/OSpeakerconnector
Link remote
mics, VM
Volume telephone, Volume telephone, chime, remote micchime, remote mic
Surveillancemodule
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
2 BGM Inputs
2 RCA/Cinch connectors (Stereo Mono)
2 attenuator for each channel (pre-adjustment) Volume, bass & treble control BASSBASS
TREBLETREBLE
BGMBGM
Mute-level can be set:-∞∞, -28, 0 dB: to allow just mixing, keeping BGM present during paging or to switch off
BGM has always lowest priority (priority level 4) Assignment to Zones
The BGM signal can be routed to the zones selected by the front panel’s zone switches
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
3 MIC/LINE Inputs (Inputs 1~3) combined XLR / phone jacks, balanced Input 1 with additional DIN jack
control input included
Volume, bass & treble control Selectable sensivity:
microphone (-60 dBV) or line signal (-10 dBV Phantom power:
can be switched on or off for all simultaneously when set to microphone sensivity
Rear
Control inputs on clamp terminal
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
Control Settings
Selectable priority: When using control inputs: priority level 1 or 2 can be selected When not using control inputs: priority level 3 is provided Channels of the same priority level, can be set either to
Last-in-first-out (LIFO) or first-in-first-out (FIFO) Assignment to Zones
- in priority level 1 or 2, the inputs can be assigned to certain zones- in priority level 3, the inputs will be routed to the zones selected by
the front panel’s zone switches Mixing
In priority level 2, mixing can be selected In priority level 3, mixing is provided
Pre-Announcement Chime Priority level 1 and 2 provide automatic pre-chime On input 3, the pre-chime can be switched off
PCB
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
1 Telephone Input Push-in terminal block (balanced) with control input
Sensivity: -10 dBV
Connection to a PABX system with an audio output and control signal output
Priority level 1 or 2 Pre-announcement chime
can be set ON or OFF
Rear PCB
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
Connection of up to 4 remote microphones parallel connection in „daisy chain“ using RJ45 connectors and category 5 cables
(4 pairs with shield)
VM-2000 (master)RJ45
* external power supply necessary for more than 1 remote microphone(AD-4800 ER, part code 100-07-291-80)
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
1 External Speaker input on push-in screw terminal to switch the connected speakers to an external
power amplifiere.g. to connect the speakers to a central system
e.g. to connect the speakers to a stand-by amplifier in case of amplifier failure
the external signal will be switched directly to the speaker lines
the attenuators will be bypassed
Rear
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
3 Line Level Outputs Recording Output
pre-master, for recording independent of master volume, level: 0 dBV
Line Outputpre-master, for connecting additional amplifiers without master volume control of VM , level: 0 dBV
Pre (amplifier) Outputpost-master, for connecting additional amplifiers with master volume control on VM, or to connect the slave VM, level: 0 dBV
Rear
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
1 Direct and 5 Zone Outputs Plug-in screw connector
for easy connection and maintenance
Output level: 100V70V and 50V by internal re-wiring
direct output without attenuator zone outputs with attenuators
6 steps: -20, -15, -10, -6, -3, 0 dB
Attenuator control outputto bypass external attenuators
Rear
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
Remote Control by external Equipment or Switches (manual control):
Activation will be made by closing or opening a contact
Rear
in some cases a control can be activated by a pulse
in other cases a control can be activated with a level signal
> 100 ms
break make
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
Remote Control by external Equipment or Switches (manual control):
Switching ON and OFF the VM Start/Stop of Emergency mode
Activation of external speaker signal input
Start pre-recorded messages (if EV-200 installed)
Chime activation Westminster chime activation (external) Fault
(to be indicated on the fault LED)
OFF ON
pre-chime post-chime
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
Remote Control of external Equipment or Indicators (LED, buzzer)
AC mains failure DC failure Power status Communication (with remote microphone) fault General Fault Emergency mode active EV-200 fault (when EV-200 installed)
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
‘‘
Nine VM-2000s can be combined to increase the output power to increase the number of zones up to 45 one unit will be master, the others all slaves the voice announcement module needs to be
installed only in the master unit the remote microphone(s) will be connected to the
master unit only Full access to each desired zone of the
slave units through the master unit
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
VM-2000 + RM-200M: 5-zone system
2x VM-2000 + RM-200M + RM-210 + EV-200:10-zone system with 5-voice message
EV-200
VM-2000 + VM-2000 + RM-200M:10-zone system
EV-200
VM-2000 + RM-200M + EV200:5-zone system with 5-voice message
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
Absolute Priority
5 priority levels are provided: Emergency: highest priority 4 priority levels (1 - 4)
Relative Prioritywhen inputs of the same priority level (1 or 2) are activated at the same time, valid for all inputs with control
last-in-first-out (LIFO) and first-in-first-out (FIFO) unit no. Priority only for RM-200M and messages 1 - 5
Mixing in priority level 2: “priority 2 mixing” is set in priority level 3
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
Audio Levels at different Priority Levels Emergency : max. level at speaker
bypass of master volume and zone attenuators, activation of external attenuator control
priority level 1 & 2: max. level output XXX - bypass of master volume and zone attenuators- when “priority 2” is set to “mixing”: no bypass of master
volume and zone attenuators for inputs of priority level 2
priority levels 3 and 4: level as setno bypass of master volume and zone attenuators
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
The VM-2000 is a package amplifier providing VA (Voice Alarm) functionsSo, it can be set into the Emergency Mode by:
depressing the remote microphones emergency key external control:
- starting the ALERT function
- starting the EVACUATION function
The Emergency mode can be stopped only by external control !
To avoid switching off easily
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
RM-200MRM-200M
Remote MicrophoneRemote Microphone
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
Elegant and modern design, slink gooseneck microphone selection for up to 10 zones Two group selection buttons All-call selection button talk button in PTT or ON/OFF mode protected emergency button, starting evacuation sequence pre- and post-announcement chime selectable Start of 5 pre-recorded messages key extension RM-210 available up to 4 remote microphones can be connected
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
d RM-210d RM-200M
Power indicatorFailure indicator
Emergency indicatorEmergency keyGroup 1 keyGroup 1 indicatorGroup 2 keyGroup 2 indicatorAll-call keyAll-call indicator
AA
BB
CC
Flashing green: RM-200M can interrupt the busy unitFlashing orange: RM-200M can not operate
Zone / messageindicationZone / messageselector key
Busy indicator:In-use indicator
Talk button
Remote microphone RM-200M Key extension RM-210Labels: can be inserted under the surface
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
d RM-210d RM-200M
AA
BB
CCC:when using EV-200 and two VM-2000 :message selector
B:when using EV-200:message 1-5 selector,
when using two VM-2000:zone 6-10 selection
A:
always zone 1-5 selection
Background Design: Torsten Kranz
29
Design: Torsten Kranz @ TEE
Connectors and Adjustment
DC POWER IN24V - 200 mA
LINK SP MICEXTERNAL
MIC IN
DC powerinput jack
RJ45 linkconnector
Microphone volume control
External microphone input jack
Function setting switch
Extensionconnector
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
Bottom side
Turn the bottom up
Connect the link cable
fix the linkage bracket B
fix the linkage bracket A
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
Prepare a hole
Place in the remote microphone
Fix the RM with screwsfrom the bottom side
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
SV-200SV-200Surveillance Board
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
Monitoring of speaker lines on
- short circuit- break - earth leakage
power amplifier on proper operation
Output of detected failures on the VM-2000 on the remote microphone(s) RM-200M on output connector
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
SURVEILLANCE I/O
SET CHECK
SP LINEIMPEDANCE
SET button: after connecting the speakers, depress here for initial measurement
CHECK button: manual start of measuring to check the speaker lines
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
EV-200EV-200
Voice Announcement Board
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
Playback of pre-recorded messages 2 Emergency messages 5 commercial messages 1 chime control via remote microphone or by external
equipment (e.g. timer) sound files on compact flash memory card
message length depends only on the card‘s size
recording and editing of the messages on EV-350
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
CPU Status Indicator
CPU RUN
ACCESS
COMPACTFLASH CARD
volume controlCard access indicator
CPU status indicator
CF card slot
Eject button
normal operation: flashesabnormal operation: steadily onno operation: extinguished
Card Access IndicatorCard access: flashesfailure: steadily on
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
In EV-200 usable memory cards:Type: CompactFlash cards
model: SDCFB-8/-16/-32/-48/-64/-96
manufacturer: SanDisk
capacity: 8 MB - 96 MB
for recording with EV-350R:CF-adapter
(e.g. SanDisk type SDCF-03)
Background Design: Torsten Kranz
Design: Torsten Kranz @ TEE
THANK YOUTHANK YOU
Recommended