Buildings and Structures 1 Building Types and Components

Buildings and Structures 1

Building Types and Components

Aim

To provide students with information that will enable them to recognise the basic types of building design and the principal components.

Learning OutcomesAt the end of the session students will be able to:

• State the most commonly used construction types

• Identify types of doors, windows and roof lights commonly used

• List the principal components of a staircase

• List the types of roof commonly found.

Types of buildings

• Solid or ‘traditional’ construction

• Structural steel frame construction

• Reinforced concrete construction

• Modular system construction

• Liftslab construction.

Solid construction

• Solid load bearing walls

• Set back at upper floors

• Commonly made of brick, concrete blocks or stone

• Cast iron columns

• Cast iron or timber beams

• Warehouses, mills, factories and offices.

Buildings and structures.

Structural steel

• High number of design options

• Skeletal framework often complex

• Loads carried by beams

• Structure is covered by cladding

• Large use of glass, polycarbonate and plastic

• Large shopping centres, sports centres and multi-storey offices.

Structural steel.

Stanchions

Main beams Roof spans between main beams

Tie Beam

Floor spans between main beams

Secondary beam

Reinforced concrete

• Alternative to steel frame

• Columns support beams on which are laid slab flooring sections

• Columns, beams and slabs integrally cast to form a monolithic structure

• Two common methods of construction.

Reinforced concrete(1)

Pre cast reinforced concrete frame

• Factory produced frame components

• Transported for assembly on site

• Similar techniques to steel frame.

Reinforced concrete(2)

Composite construction

• Utilises the advantages of modern lightweight structural steelwork

• ‘Marriage’ between steelwork & pre cast concrete columns.

Composite construction

Gable columns

Concrete Spine beam

Steel Spine beam.

‘PCR’ concrete frame.

Modular structures

• Pre fabricated components

• High design flexibility

• Specially designed connectors

• Encased in concrete to provide a degree of fire and corrosion protection.

Modular building.

Typical modular connector.

Lift slab construction

• Building framework formed by columns

• Hydraulic rams used to lift roof then floors into position

• Height can be increased by ‘splicing’ on additional sections of column.

Early phase of ‘Slab’ construction.

2nd Phase ‘Slab’ construction.

Doors, windows and rooflights

Types of door

• Hinged• Swing• Revolving• Sliding• Folding• Cantilever• Roller shutter.

Hinged doors

• Most commonly found type

• All close against a rebate on the door jamb

• Four commonly found types

Flush

Panelled

Ledged

Metal.

Swing doors

• Pin hinges allow door to swing in any direction

• Door jamb not fitted with a rebate

• Often partially glazed using wired glass or copper glazing bars

• Found in restaurants, department stores and hotels.

Revolving doors

• Present an obstruction to firefighting operations unless dealt with

• Usually 4 or 2 ‘wings’

• Designed to be collapsed down

• Essential they are used in conjunction with a hinged door.

Sliding doors

• Solid or lattice construction

• Widely used in commercial buildings

• Can slide on one or both sides of an opening or into a central recess

• Lattice type usually for security or to protect an area such as a lift or lift shaft.

Folding doors

• Usually lightweight construction

• Similar in design to hinged doors

• Two or more leaves hinged together

• Whole door opens to one side only

• Often used to separate two rooms.

Cantilever doors

• Door is counter balanced and pivoted so it rises upwards

• Lies horizontal when open

• Generally fits flush to the opening when closed

• Usually found on garages.

Roller shutters

• Nearly always made of steel

• Small examples can be raised by hand

• Large examples usually operated by means of gearing and handle or chain and block

• Usually found on commercial premises.

Windows

• Allow natural light into a building

• Serve to provide ventilation to rooms

• Generally two types, referred to according to the method of opening

Casement

Sash.

Casement windows

• The simplest form consists of a rectangular frame with the casement hung on it

• When more than one casement can be opened it is referred to as a 2,3 or 4 light casement.

DEADLIGHT

FRAME

VENTLIGHT

TRANSOM.

CASEMENT

Sash windows

• Pivoted sash - opening part supported by pivots at each side of opening part of window or top and bottom

• The term ‘SASH’ refers to the opening portion and includes the glass and the surround

• Partially inside and outside of opening when open.

Sash windows

Sliding sash windows

• Slide vertically

• Double hung is the common form of this type of sash, both sashes slide vertically in the frame

• Another type consists of two sashes, one or both of which can be opened horizontally.

STAIRS AND ROOFS

Stairs

Common materials;• Wood

• Stone

• Pre cast concrete

• Steel

• Composite.

Stairs

TREAD

RISER

BEARER

NOSING

STRING

CAPPING

PITCH LINE

RUN

GOING

RISE

SPANDREL

NEWEL POST

HEADROOM

BANNISTER

Confirmation Assessments will be based on this lesson and the corresponding study note

Learning Outcomes• The most commonly used construction types• The types of doors, windows and roof lights

commonly used• The principal components of a staircase• The types of roof commonly found.

THE END