CAMD Safety Valve PPT

Ramsbottom Safety Valve

Hareesha N Gowda

Asst. Professor

Dept of Aeronautical Engineering

Dayananda Sagar College of Engineering

Bangalore-78

5/7/2013Hareesha N Gowda, Asst Prof, DSCE, Blore-

782

Part-1: Body

• Create parallel plane as shown in fig -2, create sketch as shown in fig-1

• Select both outside circles and create protrusion, thickness 55mm as shown in fig-3

• Select base of protrusion as shown in fig 4, create circle of dia 99mm, fig-5

• Use swept protrusion, select sweep path, right click, select cirle of dia 99mm,

finish. Fig.6

fig-1 fig -2

fig-3fig 4 fig 5 Fig.65/7/2013 3

Hareesha N Gowda, Asst Prof, DSCE, Blore-

78

On parallel plane

• Use swept cutout, select swept path, right click, then select circle of dia75mm, click finish. Ref. Fig-1

• Use fillet, create fillet as shown in fig-2 of rad. 12mm.

• Create Threaded hole as shown. Ref Fig 3, 4 and Fig.5

Fig-1

fig-2

Fig 3

Fig 5

Fig 4

5/7/2013 4Hareesha N Gowda, Asst Prof, DSCE, Blore-

78

fig-1

fillet of radius 24mm

• Create fillet of Rad 24mm as shown in fig-1.

• Create parallel plane as shown in fig-2, create circle of dia 250mm as shown in

fig-3. Create protrusion as shown in fig-4

fig-2

fig-3

fig-4

5/7/2013 5Hareesha N Gowda, Asst Prof, DSCE, Blore-

78

• Create a parallel plane as shown in fig-1. Create circle of dia 124mm on bottom of the circular protrusion shown in fig -2 and create circle of dia 90mm on parallel plane created as shown in fig 3.

• Use lofted protrusion, select both circles which were

created, right click to accept, finish. Ref fig 4

fig 2

fig 3

fig-1

fig 4

5/7/2013 6Hareesha N Gowda, Asst Prof, DSCE, Blore-

78

• Create circle of dia 100mm on bottom of the circular protrusion shown in fig -1 and create circle of dia 75mm on parallel plane created as shown in fig 2.

• Use lofted cutout, select both circles which were

created, right click to accept, finish. Ref fig 3 and 4

fig -1fig -2

fig -3

fig -45/7/2013 7

Hareesha N Gowda, Asst Prof, DSCE, Blore-

78

• Cut view of the part is as shown in fig.1. Remove extra material as you can see in

fig-1, use lofted cut out again as shown in fig-2.

• Create fillet of 12mm as shown in fig 3

fig 3fig 1

Fig 2

5/7/2013 8Hareesha N Gowda, Asst Prof, DSCE, Blore-

78

• Create hole of dia 21mm, depth 25mm as shown in fig-1.

• Use circular pattern to create circular array of holes. Use this procedure

• Circular pattern � Select feature � Right click to accept � Select bottom plane

of circular protrusion � choose circular pattern in tool bar � use fill �Give rad

100mm �count 6 � spacing 60o � Select center point of arc � Select a point on

the circle � Select direction � Return.

5/7/2013 9Hareesha N Gowda, Asst Prof, DSCE, Blore-

78

• Select xz plane, create sketch as shown in fig and create rib as shown in fig-2. Rib

thickness 12, use symmetric thickness option (Both sided arrow mark)

• Use smart mirror to create rib on the other side as shown in fig-3.

fig-1

Fig-2

Fig-35/7/2013 10

Hareesha N Gowda, Asst Prof, DSCE, Blore-

78

• Select YZ plane as shown in fig-1, create sketch as shown in Fig 2

• Use symmetric protrusion, use up to next. Ref Fig 3

• Select the plane as shown in fig-4. Create sketch as shown in fig 5.

• Use cut out ( use through next). Ref Fig.6

Fig 3Fig 1 Fig 2

Fig.6Fig.5

Fig.45/7/2013 11Hareesha N Gowda, Asst Prof, DSCE, Blore-

78

• Select xz plane, create sketch as shown in Fig.1.

• Use revolved protrusion as shown in Fig.2

• Create sketch as shown in fig.3, create symmetric, through all cut out as shown in

Fig.4. Create G3 thread as shown in Fig.5. Create groove and 1mm chamfer as

shown in Fig.5

5/7/2013 12Hareesha N Gowda, Asst Prof, DSCE, Blore-

78

Fig.1

Fig.2

fig.3

Fig.4Fig.

5

Part-2

• Select xz plane, create sketch as shown

5/7/2013 13Hareesha N Gowda, Asst Prof, DSCE, Blore-

78

Part-3

5/7/2013Hareesha N Gowda, Asst Prof, DSCE, Blore-

7814

Select YZ plane, create sketch as shown, create washer of thickness 6mm Part-4

1. Select top plane

2. Crete the sketch as shown in figure

3. Use symmetric protrusion command, height-9 mm to create features as shown in

figure. Create threaded hole as shown.

5/7/2013 15Hareesha N Gowda, DSCE, Blore-78

4. Select XZ plane, create sketch as shown in fig. use revolved cutout (outside cut) to create

features as shown in figure. Mirror to other side.

Part-5Lock nut M20

Save the previous part (Lock M20 Nut) as

M20 Nut change thickness to 16 mm

Part-6nut M20

5/7/2013 16Hareesha N Gowda, Asst Prof, DSCE, Blore-

78

Part-7Link

Thickness 6 mm

5/7/2013 17Hareesha N Gowda, Asst Prof, DSCE, Blore-

78

Part-8Pin

5/7/2013 18Hareesha N Gowda, Asst Prof, DSCE, Blore-

78

Part-9Split Pin

5/7/2013 19Hareesha N Gowda, Asst Prof, DSCE, Blore-

78

Use swept protrusion

5/7/2013 20Hareesha N Gowda, Asst Prof, DSCE, Blore-

78

Part-10

XY planeXZ plane

XZ plane

Valve

5/7/2013 21Hareesha N Gowda, Asst Prof, DSCE, Blore-78

Part-11 Lever

5/7/2013 22Hareesha N Gowda, Asst Prof, DSCE, Blore-78

Part-11 Lever

5/7/2013 23

Hareesha N Gowda, Asst Prof, DSCE, Blore-78

• Select xz plane, create sketch as shown

5/7/2013 24Hareesha N Gowda, Asst Prof, DSCE, Blore-

78

• Select xz plane, create sketch as shown

5/7/2013 25Hareesha N Gowda, Asst Prof, DSCE, Blore-

78

• Select xz plane, create sketch as shown

5/7/2013 26Hareesha N Gowda, Asst Prof, DSCE, Blore-

78

• Select xz plane, create sketch as shown

5/7/2013 27Hareesha N Gowda, Asst Prof, DSCE, Blore-

78

• Select xz plane, create sketch as shown

5/7/2013 28Hareesha N Gowda, Asst Prof, DSCE, Blore-

78

• Select xz plane, create sketch as shown

5/7/2013 29Hareesha N Gowda, Asst Prof, DSCE, Blore-

78

• Select xz plane, create sketch as shown

5/7/2013 30Hareesha N Gowda, Asst Prof, DSCE, Blore-

78