View
242
Download
9
Category
Tags:
Preview:
Citation preview
CIMExcel Software Inc. Slide 1
Performance Solutions for the Mineral Processing Industry
• Advanced Mineral Processing Control (AMPC)
• Mineral Processing Operations Simulator (MPOS)
• Analysis and Engineering Services
Throughput Increase 3 - 5 % Recovery Increase 1 - 3 %
AMPC CIMExcel Software Inc. Slide 2
Advanced Mineral Processing Control (AMPC)
• Increases Stability and Reduces Variability • Increases Ore Throughput and Metal Recovery
• SAG / AG Mill Control and Optimization
• Cyclone Scheduling and Optimization
• Flotation Control and Optimization
• Integrated Conventional and Advanced Control
AMPC CIMExcel Software Inc. Slide 3
AMPC - Integrated Conventional and Advanced Control
Conventional Control:
• Feeder Speed• SAG / AG Mill Dual Power - Load Control• SAG / AG Mill Speed• SAG / AG Mill Water Ratio• SAG / AG Mill Water Addition• SAG / AG Mill Additives• SFPB and CFPB Level• Cyclone - Underflow and Overflow Water Addition• Ball Mill Additives • Flotation - Air Flow and Reagents Flow• Lube Systems Temperature
Advanced Control:
• SAG / AG Mill Feedrate, Water Ratio, and Speed • SFPB and CFPB Level• Lube Systems Temperature • Cyclone Scheduling• Cyclone - Overflow Solids• Flotation - Air Flow and Reagents Flow
AMPC CIMExcel Software Inc. Slide 4
AMPC - Throughput Optimization
• Ore Quality Analysis and Feedforward Control • Advanced Hill-Climbing Optimization• Water Ratio Optimization• Speed Optimization• Ore Load Control Mode • Feedrate and Power Constraints Mode • Continuous Response Identification and Learning
AMPC CIMExcel Software Inc. Slide 5
AMPC - Advanced Hill-Climbing Optimization
All trend windows herein display 100 minutes of operation.
AMPC CIMExcel Software Inc. Slide 6
AMPC - Throughput Optimization - Increased Throughput ~ 5 %
A and B Primary Grinding lines are identical and are fed from the same stockpile.
There are moderate variations in the stockpile ore quality.
A-line has AMPC - Throughput Optimization active and averages 951 Tph.
B-line has conventional dual power-load control and water ratio control active
and averages 901 Tph.
AMPC CIMExcel Software Inc. Slide 7
AMPC - Ore Quality Feedforward Control
The particle size distributions for the relative grinding time (RGT = 0.8, 1.0, 1.2) are determined from belt cut testing and correlation with the Ore Size Analyzer data.
The realtime Ore Size Analyzer data is used to determine the current value of the Relative Grinding Time.
The Relative Grinding Time, the current steel load, and the time from the last lifter/liner/grate rebuild are used to determine the Maximum Feedrate.
AMPC uses the Maximum Feedrate value as the remote setpoint to the Feedrate Control Loop.
AMPC CIMExcel Software Inc. Slide 8
AMPC - Ore Quality Feedforward Control
Ore Quality Feedforward Control provides very stable primary mill operation during moderately variable ore quality conditions.
AMPC CIMExcel Software Inc. Slide 9
Conventional Power-Load Control Loop
For the conventional power-load control loop for the above primary mill power and load performance curves, the operator needs to enter a water ratio value (0.65), a power setpoint value (6700 kw), a load setpoint value (660 psi), a high power feeder cutback value (7100 kw), and a high load feeder cutback value (675 psi).
These values are critical and determine the throughput and the operating stability of the primary mill. If feeder cutbacks are encountered - the operator will lower these values, if no feeder cutbacks have been encountered - the operator will raise these values.
AMPC CIMExcel Software Inc. Slide 10
AMPC - Ore Quality Feedforward Control
In the above, A-line and B-line are fed from the same stockpile with moderately varying ore quality. A-line has Ore Quality Feedforward active and averages 962 Tph.B-line has Conventional Power-Load Control active and averages 652 Tph.
There is a significant performance improvement with AMPC Ore Quality Feedforward Control.
AMPC CIMExcel Software Inc. Slide 11
AMPC - Recovery Optimization
• Cyclone Scheduling and Optimization
• Flotation Solids Control and Optimization
• Flotation (Air and Reagents) Feedforward Control
AMPC CIMExcel Software Inc. Slide 12
AMPC - Recovery Optimization - Increased Recovery ~ 2 %
A1 and A2 Ball Mill - Cyclones - Flotation sides are identical and are fed equally
from the same primary mill with the same particle size distribution.
A1-side has AMPC - Cyclone Scheduling active, A2-side does not.
Both sides have OF Density Optimization, Feedforward Air Ratio and Reagents Flow Ratio active.
A1-side averages 89.8% recovery efficiency.
A2-side averages 87.6% recovery efficiency.
Mineral Processing Operations Simulator (MPOS)• Operator Training Facilities (for junior to senior operators)• Control System Checkout• Advanced Control System Design and Testing• HMI Design and Testing• Process and Equipment What-if Analysis
Operator Training Facilities:
• Control Room HMI Displays and Inputs • DCS/PLC Control System• Motors • Process Model - Accurate Operating Values and Dynamic Responses • Operator Training Scenarios - Variations in Ore Quality and Failures of Equipment
MPOS CIMExcel Software Inc. Slide 13
MPOS CIMExcel Software Inc. Slide 14
MPOS - Operator Training Facilities - Control Room Displays
MPOS CIMExcel Software Inc. Slide 15
MPOS - Particle Size Distributions - Stockpiles to Tailings
MPOS CIMExcel Software Inc. Slide 16
MPOS - Semi-Autogenous Mill Model
MPOS CIMExcel Software Inc. Slide 17
MPOS - Autogenous Mill Model
MPOS CIMExcel Software Inc. Slide 18
MPOS - Pebble Crusher Model
MPOS CIMExcel Software Inc. Slide 19
MPOS - Ball Mill Model
MPOS CIMExcel Software Inc. Slide 20
MPOS - Cyclone Model
MPOS CIMExcel Software Inc. Slide 21
MPOS - Flotation Model
MPOS CIMExcel Software Inc. Slide 22
MPOS - Comprehensive Operator Training Scenarios
CIMExcel Software Inc. Slide 23
Analysis Services• Primary Crushing Operations - Ore Size Distribution and Variability Analysis
• Stockpile Ore Size Distribution Measurement, Classification and Grindability Analysis
• SAG / AG Mill Feedrate, Power, and Load Testing and Analysis
• SAG / AG Mill Speed and Water Ratio Testing and Analysis
• Pebble Crusher Performance Testing and Analysis
• SAG / AG Mill, Ball / Rod Mill, Pebble Crusher, Screening Particle Size Distributions (PSD)
• Screen Feed Pump Curves
• Cyclone Pack Pressure and Flow Curves
• Cyclone Overflow and Underflow Mass Flow and Solids Curves
• Cyclone Overflow and Underflow PSD Analysis and Partition Curves
• Ball / Rod Mill Power Draw Curves
• Flotation Feed Grade, PSD, Slurry Flow, Air Flow, Reagents Flows, and Recovery
Analysis
• Tailings - Critical Particle Size and Sanding Rate Analysis
CIMExcel Software Inc. Slide 24
Engineering Services
• Instrumentation Requirements
• Signal Processing and Filtering Design and Testing
• OPC Connectivity and Integration
• Process Controllability and Variability Analysis
• Control Loop Functional Analysis, Design and Testing
• User Interface Functional Analysis, Design and Testing
• IEC 1131 Specifications, Programming and Testing
• DCS Checkout Support
• System Startup and Troubleshooting Support
Recommended