View
1
Download
0
Category
Preview:
Citation preview
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
1 Control System Laboratory, EEE
(For CSE, ECE & EEE)
MASTER MANUAL
CONTROL SYSTEMS LAB
II Year B.Tech. EEE II - Sem
Prepared By
Goutam Barma
Asst. Prof. EEE
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
2 Control System Laboratory, EEE
(For CSE, ECE & EEE)
INDEX
Sl. No Experiment Name Page No.
1 CHARACTERISTICS OF SYNCHRO TRANSMITTER AND
RECEIVER PAIR
3
2 CHARACTERISTICS OF AC SERVOMOTOR
9
3
EFECT OF FEEDBACK ONDC SERVOMOTOR
15
4 TEMPERATURE CONTROL USING PID 19
5 TIME RESPONSE OF SECOND ORDER SYSTEM 22
6
PROGRAMMABLE LOGIC CONTROLLER
27
7 ROOT LOCUS PLOT, BODE PLOT USING MATLAB.
36
8 STATE SPACE MODEL FOR A GIVEN CLASSICAL TRANSFER
FUNCTION
42
9 TRANSFER FUNCTION OF DC GENERATOR 45
10 TRANSFER FUNCTION OF DC MOTOR 49
11 EFFECT OF P, PI AND PID CONTROLLER ON
A SECOND ORDER SYSTEM
54
12 LAG AND LEAD COMPENSATION -
MAGNITUDE AND PHASE PLOT
58
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
3 Control System Laboratory, EEE
(For CSE, ECE & EEE)
EXPERIMENT NO.1
CHARACTERISTICS OF SYNCHRO TRANSMITTER AND
RECEIVER PAIR
AIM: a) To study the characteristics of synchro Transmitter.
b) To study the characteristics of synchro transmitter and receiver pair.
APPARATUS:
1. Synchro Transmitter and receiver pair trainer kit.
2. Patch cords.
Characteristics of Synchro Transmitter.
CIRCUIT DIAGRAM:
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
4 Control System Laboratory, EEE
(For CSE, ECE & EEE)
PROCEDURE:
1. Connect the main supply to the system with the help of cable provided. Do not connect
any patch cords to terminals marked S1, S2, and S3.
2. Switch on mains supply for the unit.
3. Starting from zero position, note down the voltage between stator winding terminals i.e.
VS1 S2, VS2 S3, and VS3 S1 in a sequential manner. Enter readings in a tabular form and
plot a graph of angular manner. Enter readings in tabular form and plot a graph of angular
position of rotor vs. stator voltages for all three phases.
4. Note that zero position of the stator, rotor coincides with VS3 S1 voltage equal to zero
voltage. Don’t disturb this condition.
OBSERVATIONS:
Sl.
No.
Rotor position in
degrees
STATOR TERMINAL VOLTAGE
VS3S1 VS1S2 VS2S3
1 0
2 30
3 60
4 90
5 120
6 150
7 180
8 210
9 240
10 270
11 300
12 330
13 360
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
5 Control System Laboratory, EEE
(For CSE, ECE & EEE)
MODEL GRAPH:
Study of synchro transmitter & receiver pair
CIRCUIT DIAGRAM:
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
6 Control System Laboratory, EEE
(For CSE, ECE & EEE)
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
7 Control System Laboratory, EEE
(For CSE, ECE & EEE)
PROCEDURE:
1. Connect the mains supply with the help of cable provided.
2. Connect S1, S2 and S3 terminals of transmitter to S′1, S′2 and S′3 of synchro receiver by
patch cords provided respectively.
3. Main supply Switch on transmitter and reciever and also switch on the.
4. Move the pointer i.e. rotor position of synchro transmitter Tx in steps of 300 and observe
the new rotor position on receiver side which follows its both the directions of rotations
and their positions are in good agreement.
5. Enter the input angular position and output angular position in the tabular form and plot a
graph.
OBSERVATIONS:
S.No Transmitter Rotor
angle ( deg )
Receiver Rotor
angle ( deg )
1 30
2 60
3 90
4 120
5 150
6 180
7 210
8 240
9 270
10 300
11 330
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
8 Control System Laboratory, EEE
(For CSE, ECE & EEE)
12 360
MODEL GRAPH :
RESULT:
VIVA QUESTIONS:
1. Define synchro transmitter?
2. Define synchro receiver?
3. What are applications of synchro transmitter and receiver?
4. where it is used?
5. Explain Working Principle of synchro transmitter and receiver?
6. Draw the Ckt of synchro transmitter and receiver?
7. How it is useful to do this experiment
8. Write the terminal Voltages of the stator for Synchro Transmitter?
9. What is a synchro?
10. What are the names of synchros?
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
9 Control System Laboratory, EEE
(For CSE, ECE & EEE)
EXPERIMENT NO. 2
CHARACTERISTICS OF AC SERVOMOTOR
AIM: To study the Characteristics of AC Servomotor & to draw its Speed – Torque
Characteristics.
APPARATUS:
1. AC Servo Motor Unit
2. Multimeter
CIRCUIT DIAGRAM:
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
10 Control System Laboratory, EEE
(For CSE, ECE & EEE)
SPEED Vs BACK EMF CHARACTERISTICS:
PROCEDURE:
1. Study all the labels on the front panel carefully.
2. Initially keep load and servo motor switch at OFF position.
3. Keep P1 (load control knob of DC motor) and P2 (speed control knob of ac servo motor)
at minimum position.
4. Now switch ON main supply to the unit and also AC Servo Motor supply switch.
5. With load switch in OFF position vary the speed of AC Servo Motor by moving the
control voltage. This is done by varying the knob P2.
6. For different speed note down back e.m.f (in mili-volt) generated by DC motor at TP1
terminal using DMM.
7. Bring P1 and P2 to minimum position. Switch of the servomotor and the main supply to
the kit.
8. Plot the graph speed Vs back emf
TABULATION:
Sl. No. Speed (RPM) Back emf (mili-volt)
1 550
2 650
3 750
4 850
5 950
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
11 Control System Laboratory, EEE
(For CSE, ECE & EEE)
MODEL GRAPH:
SPEED Vs TORQUE CHARACTERISTICS:
PROCEDURE:
1. Switch ON the supply to the kit and also switch ON the servomotor. Keep the load switch
at OFF position
2. Vary P2 to set the control winding at Vc1=45V. This voltage can be measured by using
DMM at the terminals labeled “Control winding voltage” on the front panel of
servomotor kit.
3. Vary the load control knob P1 in steps and in each step note down the back emf, armature
current and speed.
4. Vary P2 to set the control winding at Vc2=50V and Vc3=55V and repeat the step 3.
6. Bring P1 to its minimum position and then bring P2 to its minimum position. Switch OFF
load, servomotor and main supply switch on by one.
5. Calculate the power and torque and plot the speed Vs torque characteristic of motor.
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
12 Control System Laboratory, EEE
(For CSE, ECE & EEE)
TABULATION:
Vc1 = 45V
Vc2 = 50V
S.NO Ia(mA) Speed
N(rpm) Eb(mV)
Power
(mW) T(N-m)
1 0.1
2 0.15
3 0.2
4 0.25
5 0.3
6 0.35
7 0.4
8 0.45
9 0.5
S.NO Ia(mA) Speed
N(rpm) Eb(mV)
Power
(mW) T(N-m)
1 0.1
2 0.15
3 0.2
4 0.25
5 0.3
6 0.35
7 0.4
8 0.45
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
13 Control System Laboratory, EEE
(For CSE, ECE & EEE)
Vc2 = 55V
CALCULATIONS:
Power P = Eb×Ia
T=60×𝑃×1.094×104
2𝜋×𝑁 gm-cm
9 0.5
S.NO Ia(mA) Speed
N(rpm) Eb(mV)
Power
(mW) T(N-m)
1 0.1
2 0.15
3 0.2
4 0.25
5 0.3
6 0.35
7 0.4
8 0.45
9 0.5
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
14 Control System Laboratory, EEE
(For CSE, ECE & EEE)
MODEL GRAPHS:
RESULT:
VIVA QUESTIONS:
1. Define Motor classifications?
2. What are applications of A,C servo Motor?
3. where it is used?
4. Explain Working Principle of A,C servo Motor?
5. Draw the Ckt of A,C servo Motor?
6. How it is useful to do this experiment
7. Difference between normal A.C motor & A,C servo Motor?
8. Draw the characterstics of A,C servo Motor?
9. Write Difference between D.C Servo Motor & A,C servo Motor?
10. What is the overall efficiency of A,C servo Motor?
11. Write the Transfer function equation for A,C servo Motor?
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
15 Control System Laboratory, EEE
(For CSE, ECE & EEE)
EXPERIMENT NO. 3
EFECT OF FEEDBACK ONDC SERVOMOTOR
AIM: To study the effect of feedback on DC Servo Motor by its Torque-Speed characteristic
APPARATUS:
1. DC Servo Motor Kit
2. Multimeter
CIRCUIT DIAGRAM:
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
16 Control System Laboratory, EEE
(For CSE, ECE & EEE)
PROCEDURE:
1. Before switch ON the instrument, please see that armature control potentiometer and
field control potentiometer are at minimum position so that the armature voltage applied
to the armature from zero volts onwards and field voltage applied to the field from 25V
onwards.
2. Switch ON the instrument, observe that the field on indication LED glows, if not then
immediately switch OFF the instrument. Please note that for all DC motors field voltage
to be given initially before applying the armature voltage. Initially DC ammeter and
RPM meter indicates ZERO reading.
3. Connect the ammeter to the terminal of field voltage Adjust spring balance so that there
is minimum load on the DC Servo Motor. You may fix knob at any particular place to
apply a fixed load on the DC Servo Motor.
4. Adjust armature control potentiometer so that Va = 10V and field control potentiometer
so that Vf = 20V by using digital ammeter.
5. Note down T1, T2, Armature Current (Ia) and Speed.
6. Keeping Va = 10V, Vf = 20V, adjust T1 up to 500 gm in suitable steps and note down the
readings as in step 6.
7. Now repeat the step 7 for Va = 15, 20 and 25 by keeping Vf at 20V.
8. You may repeat the steps 7 & 8 for Vf = 15V, 10V.
TABLE:
Field Voltage (Vf) = 20 V
Sl. No. T1
(gms)
T2
(gms) T = T1 - T1
Torque = T *
3.5
Speed
(rpm)
I a
(mA)
Va =
10 V
1
2
3
4
5
6
Va
=15 V
1
2
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
17 Control System Laboratory, EEE
(For CSE, ECE & EEE)
MODEL GRAPH:
RESULT: Hence the effect of Feedback on DC Servomotor has been studied with the help of
Torque-sped characteristics.
Viva-Voice Questions
1. Draw the speed torque characteristics of D.C Servo motor?
2. What are the applications of D.C Servo motor?
3. What are the types of D.C. Servo motor?
4. Write the formula for the torque in case of d.c. servo motor?
5. Compare ac and dc servo motors
6. Define Motor classifications?
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
18 Control System Laboratory, EEE
(For CSE, ECE & EEE)
EXPERIMENT NO. 4
TEMPERATURE CONTROL USING PID
AIM: To study the performance of various types of controllers used to control the temperature
of an oven and to draw the characteristics.
APPARATUS:
1. Temperature Control System Kit
2. Oven
3. Patch chords.
4. Stop watch
BLOCK DIAGRAM:
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
19 Control System Laboratory, EEE
(For CSE, ECE & EEE)
PROCEDURE:
I Identification of Oven Parameters :
1. Connect P output to the actuator input.
2. Keep the Switch S1 to ‘WAIT ‘ & S2 to ‘SET’, Open the feedback terminals and Switch
ON the kit.
3. Set the P Potentiometer to 1 (max).
4. Adjust the reference Potentiometer to set 5°C on the DVM. This provides an input of 0.5 V
to the driver.
5. Connect the Oven.
6. Put the Switch S2 to ‘MEASURE’ position and note down the room temperature.
7. Put the switch S1 to ‘RUN’ position and note the temperature readings for every 15 sec till
the temperature becomes almost constant.
8. Plot the temperature – time curve on a graph paper. Calculate the Values of T1 & T2 from
the graph and the open loop temperature constant ( K ).
K = Oven Temperature at steady state
Input in Volts.
II Proportional – Integral – Derivative Controller :
1. Starting with a cool oven, put the switch S1 to WAIT position and connect P,D,I
outputs to the actuator input. Keep R output disconnected. Short the feedback
terminals.
OBSERVATIONS:
S.No. Time (sec) Temp (οC)
(Open Loop)
Temp (οC)
(Closed Loop)
1 0
2 30
3 60
4 90
5 120
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
20 Control System Laboratory, EEE
(For CSE, ECE & EEE)
6 150
7 180
8 210
9 240
10 270
11 300
12 330
13 360
14 390
15 420
16 450
17 480
18 510
19 540
20 570
21 600
MODEL GRAPHS:
Open Loop Respons
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
21 Control System Laboratory, EEE
(For CSE, ECE & EEE)
Temperature response for P, PI, PID control
RESULT: The performance of various types of controllers used to control the temperature of
an oven are studied and its performance characteristics have been plotted.
Viva-Voice Questions
1. Draw the PID CONTROLLER?
2. What are the applications of PID CONTROLLER?
3. Define PID CONTROLLER?
4. Where it is used?
5. Explain Working Principle of PID CONTROLLER?
6. How it is useful to do this experiment?
7. What are the types of controllers?
8. Explain each one with neat sketch?
9. Draw the characteristics of PID CONTROLLER?
10. What are the advantages of PID CONTROLLER?
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
22 Control System Laboratory, EEE
(For CSE, ECE & EEE)
EXPERIMENT NO. 5
TIME RESPONSE OF SECOND ORDER SYSTEM
AIM: To study the time response for a second order system and to determine the time domain
specifications for a unit step signal.
APPARATUS:
1. Time Response of a second order system Trainer Kit
2. C.R.O.
3. Patch cords.
CIRCUIT DIAGRAM:
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
23 Control System Laboratory, EEE
(For CSE, ECE & EEE)
PROCEDURE:
1. Give the connection as per the circuit diagram. Switch ON the Main supply and the
trainer kit.
2. Using CRO set the Square wave at 2 Volt peak to peak. Draw the input square wave
signal.
3. Connect the output of square wave signal source to the input of second order system.
4. Using CRO observe the output and draw (unit step response)
5. From the step response on CRO screen not down Td, Tr, Tp, Ts and %Mp
6. For different values of gain repeat step no. 4 and 5.
7. Find the transfer function of the second order system inside the trainer kit.
OBSERVATION:
Sl No Gain
(KA) Td Tr Tp %Mp Ts Ess
1
2
3
4
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
24 Control System Laboratory, EEE
(For CSE, ECE & EEE)
CALCULATIONS:
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
25 Control System Laboratory, EEE
(For CSE, ECE & EEE)
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
26 Control System Laboratory, EEE
(For CSE, ECE & EEE)
MODEL GRAPH:
ESULT:
VIVA QUESTIONS:
1. What is Time Response?
2. Define Delay Time, Rise Time, Peak Time, Peak Over Shoot, Settling Time?
3. Define type and order of a system?
4. Distinguish between Type and Order of a system?
5. What is Steady State Error?
6. The damping ratio of system is 0.6 and the natural frequency of oscillation is 8 rad per sec.
Determine the rise time.
7. Define Positional Error Constant and Velocity Error Constant?
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
27 Control System Laboratory, EEE
(For CSE, ECE & EEE)
EXPERIMENT NO. 6
PROGRAMMABLE LOGIC CONTROLLER
AIM: To verify truth tables of all logic gates.
APPARATUS:
1. PLC Kit
2. WLP(WEG Ladder Program) software
PROCEDURE:
1. Switch ON the PLC kit. Observe the input and output switches
2a. Open WLP2.06
b. File New Type File name
c. Draw the ladder diagram for the given Boolean function
d. Save Compile Ladder Diagram
e. To clear PLC memory:
Communications PLC Memory Clear
f. To write on to the PLC memory:
Communications PC↔PLC PLC Write
g. Communications PLC Run
3. Verify the Boolean function (or Truth table) implemented by using the input and output
switches
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
28 Control System Laboratory, EEE
(For CSE, ECE & EEE)
(A) NOT Gate:
PLC implementation:
(B) OR Gate:
PLC implementation using WLP:
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
29 Control System Laboratory, EEE
(For CSE, ECE & EEE)
(C) AND Gate:
PLC implementation using WLP:
(D) NAND Gate:
PLC implementation using WLP:
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
30 Control System Laboratory, EEE
(For CSE, ECE & EEE)
(E) NOR Gate:
PLC implementation using WLP:
(F) XOR Gate:
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
31 Control System Laboratory, EEE
(For CSE, ECE & EEE)
PLC implementation using WLP:
(G) XNOR Gate:
PLC implementation using WLP:
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
32 Control System Laboratory, EEE
(For CSE, ECE & EEE)
(H) HALF Adder:
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
33 Control System Laboratory, EEE
(For CSE, ECE & EEE)
PLC implementation using WLP:
(I) Full Adder:
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
34 Control System Laboratory, EEE
(For CSE, ECE & EEE)
PLC implementation using WLP:
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
35 Control System Laboratory, EEE
(For CSE, ECE & EEE)
RESULT:
Viva-Voice
1. What are the applications of PROGRAMMABLE LOGIC CONTROLLER?
2. Define PROGRAMMABLE LOGIC CONTROLLER?
3. where it is used?
4. Explain Working Principle of PROGRAMMABLE LOGIC CONTROLLER?
5. How it is useful to do this experiment?
6. What are the types of PROGRAMMABLE LOGIC CONTROLLER?
7. Explain each one with neat sketch?
8. Draw the characteristics of PROGRAMMABLE LOGIC CONTROLLER?
9. What are the advantages of PROGRAMMABLE LOGIC CONTROLLER?
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
36 Control System Laboratory, EEE
(For CSE, ECE & EEE)
EXPERIMENT NO. 7
ROOT LOCUS PLOT, BODE PLOT USING MATLAB.
AIM: To obtain Root Locus plot & Bode plot for a given Transfer Function using MATLAB.
APPARATUS: MATLAB Software
PROGRAM:
I) ROOT LOCUS PLOT
num = input (‘Enter the Numerator‘)
den = input (‘Enter the Denominator’)
sys = tf(num,den)
rlocus(sys)
disp(‘The root locus Plot is displayed.’);
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
37 Control System Laboratory, EEE
(For CSE, ECE & EEE)
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
38 Control System Laboratory, EEE
(For CSE, ECE & EEE)
II) BODE PLOT
num = input (‘Enter the Numerator‘)
den = input (‘Enter the Denominator’)
sys = tf(num, den)
bode(sys)
disp(‘The bode Plot is displayed.’);
G(s)H(S)=(𝑺+𝟓)
𝑺(𝑺+𝟑)
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
39 Control System Laboratory, EEE
(For CSE, ECE & EEE)
G(s)H(S)=𝟐𝟒𝟐(𝑺+𝟓)
𝑺(𝑺+𝟏)(𝑺𝟐+𝟓𝑺+𝟏𝟐𝟏)
G(s)H(S)=𝟏𝟎𝟎(𝟎.𝟎𝟐𝑺+𝟏)
(𝑺+𝟏)(𝟏+𝟎.𝟏𝑺)(𝟎.𝟎𝟏𝑺+𝟏)
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
40 Control System Laboratory, EEE
(For CSE, ECE & EEE)
III) Nyquist PLOT
num = input (‘Enter the Numerator‘)
den = input (‘Enter the Denominator’)
sys = tf(num,den)
nyquist(sys)
disp(‘The nyquist Plot is displayed.’);
G(s)H(S)=𝟒𝟎
(𝑺+𝟒)(𝑺𝟐+𝟐𝑺+𝟐)
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
41 Control System Laboratory, EEE
(For CSE, ECE & EEE)
G(s)H(S)=(𝟏+𝟎.𝟓𝑺)(𝟏+𝑺)
(𝑺−𝟏)(𝟏+𝟏𝟎𝑺)
Viva voce:
1. Define root locus?
2. Define bode plot?
3. Define centroid?
4. Define frequency domain specifications?
5. Define the angle of departure?
6. Define angle of arrival?
7. Define resonance peak?
8. How the break away point is calculated?
9. Write the formula for the angle of asymptotes?
10. Where the root locus originates, where it terminates?
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
42 Control System Laboratory, EEE
(For CSE, ECE & EEE)
EXPERIMENT NO. 8
STATE SPACE MODEL FOR A GIVEN CLASSICAL
TRANSFER FUNCTION
AIM: To obtain State Space Model for a given Transfer Function and to obtain the Transfer
Function for a given State Space Model
APPARATUS: MATLAB Software
PROGRAM:
State Space Model for a given Transfer Function
disp (‘Transformation from Transfer function to State Space Model’);
num = input(‘Enter the Numerator:’)
den = input (‘Enter the Denominator:’)
sys = tf(num,den)
disp( ‘State Space Model for the given Transfer Function is’)
[A B C D] = tf2ss(num,den)
--------------------------------------------------------------------------
Transfer Function of given system is
Transfer Function:
2s^2 + 3 s + 2
----------------------------
2 s^4 + s^3 + s^2 + 2s
Corresponding State Space Model A,B,C,D are:
A = -0.5000 -0.5000 -1.0000 0
1.0000 0 0 0
0 1.0000 0 0
0 0 1.0000 0
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
43 Control System Laboratory, EEE
(For CSE, ECE & EEE)
B = 1
0
0
0
C = 0 1.0000 1.5000 1.000
D = 0
Transfer Function for a given State Space Model
disp(‘Transformation from State space model to Transfer Function’);
A= input(‘Enter the values of matrix A: ‘)
B= input(‘Enter the values of matrix B: ‘)
C= input(‘Enter the values of matrix C: ‘)
D = input(‘Enter the values of matrix D: ‘)
disp(‘Transfer Function for the given state space model is’)
[num,den] = ss2tf(A,B,C,D)
Sys = tf(num,den)
----------------------------------------------------
A, B, C, D Matrices of given State Space Model are:
A = 1 2
3 4
B = 1
1
C = 1 0
D = 0
And corresponding Transfer Function is :
Transfer Function
S – 2
---------------
S^2 – 5 s - 2
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
44 Control System Laboratory, EEE
(For CSE, ECE & EEE)
Viva voce:
1. Write the state model?
2. What are the different methods to represent state model?
3. Write the formula for the transfer function?
4. Write the properties of state transition matrix?
5. Write the canonical representation?
6. What are the advantages of phase variable representation?
7. What are the advantages of physical variable representation?
8. What are the advantages of canonical variable representation?
9. What are the advantages of Jordan variable representation?
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
45 Control System Laboratory, EEE
(For CSE, ECE & EEE)
EXPERIMENT NO. 9
TRANSFER FUNCTION OF DC GENERATOR
AIM: To obtain the transfer function of D.C Generator
APPARATUS:
1. Transfer function study module
2. DC generator 1500 rpm, 220V, 0.37 Amp
3. DC motor 1500 rpm, 220V, 0.37 Amp
4. Multi-meter
5. Patch Chord
TRANSFER FUNCTION MODEL:
The transfer function of a d.c. generator is derived as follows:
The differential equations relating various variables are
Vf (t) = Lf ff
fiR
dt
di (t) and
Vg(t) = Kg if(t)
Taking Laplace transform of above equations:
Vf (s) = Lf s If (s) + Rf If (s)
If (s) = ff
f
sLR
sV
)(and If(s) * Kg = Vg (s)
The two eqns. can be represented by a block diagram as follows:
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
46 Control System Laboratory, EEE
(For CSE, ECE & EEE)
The overall transfer function is
)(
)(
sV
sV
f
g
ff sLR
Kg
The values of Kg, Rf and Lf are determined from the experiment.
CIRCUIT DIAGRAM:
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
47 Control System Laboratory, EEE
(For CSE, ECE & EEE)
PROCEDURE:
1. Study the front panel of TRANSFER FUNCTION MODULE clearly.
2. Give the connection as per the circuit diagram.
3. Use the variable dc voltage source (0-220V DC) to supply the armature voltage of motor and
keep it at minimum position.
4. Use the fixed voltage source of 220V dc to supply filed of the motor.
5. Use the variable dc voltage source (100-220V DC) to supply the field of the generator and
keep it at minimum position.
6. Switch ON the supply mains and TRANSFER FUNCTION MODULE.
7. Vary the armature voltage of motor until the motor reaches its rated speed.
8. Note down the If and Eg of the generator.
9. Vary the If by varying the field voltage of the generator and note down the corresponding Eg.
10. Keep varying If until Eg reaches its rated value.
11. Bring the filed voltage knob of generator to minimum position.
12. Bring the armature voltage knob of motor to minimum position.
13. Switch OFF TRANSFER FUNCTION MODULE.
14. Switch OOF the mains supply.
15. Plot Eg Vs If graph.
16. Use multimeter to measure field resistance of generator Rf.
17. Take filed inductance of generator Lf = 5.1 H
18. Find the transfer function of the given dc generator.
TABULATION:
S.No. Field Current IF (A) Generated Voltage EG ( V )
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
48 Control System Laboratory, EEE
(For CSE, ECE & EEE)
MODEL GRAPH:
RESULT:
The transfer function of the D.C Generator is found to be ------------------------------
Viva-Voice:
1. Draw the Ckt of Transfer function of D.C Generator?
2. What are the applications of function of D.C Generator?
3. Define function of D.C Generator?
4. where it is used?
5. Explain Working Principle of function of D.C Generator?
6. How it is useful to do this experiment?
7. What are the types of function of D.C Generator?
8. Explain each one with neat sketch?
9. Draw the characteristics of function of D.C Generator?
10. What are the advantages of function of D.C Generator?
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
49 Control System Laboratory, EEE
(For CSE, ECE & EEE)
EXPERIMENT NO. 10
TRANSFER FUNCTION OF DC MOTOR
Aim: To derive the transfer function of the given DC motor
APPARATUS:
1. DC Motor –generator study unit
2. Patching Chord
CIRCUIT DIAGRAM:
THEORY:
Various parameters of a dc motor are given below
Ra = Armature resistance (ohm) La =Armature inductance (Henry)
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
50 Control System Laboratory, EEE
(For CSE, ECE & EEE)
J = Motor Inertia (KG-m2) B = co-efficient of viscous friction (N-m/rad per
sec)
Ia = Armature current (Amp.) T = Electromagnetic torque developed (N-m)
Ea = Voltage supplied to armature of motor (Volt)
Eb = Back emf induced across armature of motor (Volt)
Kb = Back emf constant (V/rad per sec)
Kt = Torque constant (N-m/Amp)
The simplified form of transfer function of a dc motor is given by
𝜔(𝑠)
𝐸𝑎(𝑠) =
𝐾𝑚
1+𝑠𝜏𝑚
Where
Km = Motor constant and 𝜏𝑚 = electro-mechanical time constant
𝐾𝑚 = 𝐾𝑡
𝐾𝑡.𝐾𝑏+𝑅𝑎 .𝐵 and 𝜏𝑚 =
𝑅𝑎 .𝐽
𝐾𝑡.𝐾𝑏+𝑅𝑎 .𝐵
PROCEDURE:
(A) To determine Kb: DC motor characteristics
1. Keep the motor load in ‘0’ position.
2. Keep the RESET switch in ‘RESET’ position.
3. Connect the patch chord from Ea terminal to DVM terminal.
4. Set Ea at 3V, 4V, 5V, 6V, 7V, 8V, 9V, 10V and note down the speed from the RPM meter on
the motor unit panel.
5. Bring the Ea potentiometer to its minimum position. Switch OFF the kit.
6. Assuming Ea = Eb, determine the Kb for each speed using the following formula
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
51 Control System Laboratory, EEE
(For CSE, ECE & EEE)
Kb= 30×𝐸𝑏
𝜋×𝑁 Volt/ rad per second
7. Find the average value of Kb from the table no. 1
8. Plot Eb Vs ω
Table No. 1
Sl.
No
Ea
(Volts)
N
(RPM) ω =
2𝜋×𝑁
60
(rad/sec)
Kb= 30×𝐸𝑏
𝜋×𝑁
(Volt/ rad per second)
1 3
2 4
3 5
4 6
5 7
6 8
7 9
8 10
Average Kb
(B) To determine B: Speed-torque characteristics DC motor
1. Keep the motor load in ‘0’ position.
2. Keep the RESET switch in ‘RESET’ position.
3. Connect the patch chord from Ea terminal to DVM terminal.
4. Set Ea at 8V.
5. Note down speed (N), armature current (Ia). Calculate ω, T, and B.
6. Change the load position from ‘0’ to ‘5’ once at a time and for each load position repeat step
no. 4
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
52 Control System Laboratory, EEE
(For CSE, ECE & EEE)
7. Bring the load to its ‘0’ position. Bring the Ea potentiometer to its minimum position. Switch
OFF the kit.
8. Find the average value of B from table no. 2.
9. Plot T Vs ω
Table No. 2
Ea = 8V
Sl.
No.
Load
position
N
(RPM) ω =
2𝜋×𝑁
60
(rad/sec)
Ia
(Amp)
T = Kb × Ia
(N-m) B =
𝜔
𝑇
(N-m/rad per sec)
1 0
2 1
3 2
4 3
5 4
6 5
Average B
(B) To determine 𝝉𝒎 : Step response of DC motor
1. Keep the motor switch in OFF position. Keep the load switch in ‘0’ position. Keep the RESET
switch in ‘RESET’ position.
2. Connect Ea and digital voltmeter terminals. Switch on the kit. Set Ea = 6 volts.
3. Note down the speed (N) of the motor and emf generated (Eg) across the armature of the
generator. These are the steady state values.
4. Using Es potentiometer, set Es = 0.632×Eg. This is the generator voltage at which the counter
will stop counting.
5. Switch OFF the motor. Keep the ‘RESET’ switch at READY position.
6. Now switch the motor ON and note down the counter reading as time constant in mili second.
7. For Ea = 8V and 10V repeat step no. 2, 3, 4, 5 and 6.
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
53 Control System Laboratory, EEE
(For CSE, ECE & EEE)
8. Bring the Ea potentiometer to its minimum position. Switch OFF the kit.
9. Find the average 𝝉𝒎 from the table no. 3
CALCULATION:
Ra = 4.5 Ohm, B=____________ N-m/rad per sec, 𝝉𝒎= _________ × 𝟏𝟎−𝟑 Sec
𝐾𝑚 = 𝐾𝑡
𝐾𝑡.𝐾𝑏+𝑅𝑎 .𝐵
The transfer function of the dc motor is
𝜔(𝑠)
𝐸𝑎(𝑠) =
𝐾𝑚
1+𝑠𝜏𝑚
Where
RESULT:
Transfer function of DC motor is given by ___________________________
VIVA:
1. What are the types of methods available to control the speed of a dc motor?
2. Why mechanical time constant is more than electrical time constant?
3. How speed and viscosity are related?
4. Can you justify that back emf constant = torque constant?
5. What is nature of relationship between torque and armature current in dc motor?
6. What is a PMDC motor?
7. Why small motors have high armature resistances compared to large motors?
8. Why large motors have high inductance resistances compared to small motors?
9. How to measure inductance of a dc motor?
10. What is the order of a dc motor?
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
54 Control System Laboratory, EEE
(For CSE, ECE & EEE)
EXPERIMENT NO. 11
EFFECT OF P, PI AND PID CONTROLLER ON A SECOND ORDER SYSTEM
AIM: To study the effect of P, PI and PID controller on a response of a second order system.
APPARATUS:
1. PID controller kit
2. C.R.O.
3. Patch chords
CIRCUIT DIAGRAM:
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
55 Control System Laboratory, EEE
(For CSE, ECE & EEE)
PROCEDURE:
Proportional [P] Controller
1. Make the connections as given in the circuit diagram. Keep I and D controllers at OFF
position.
2. Connect Second Order System in the loop and also connect Square Wave input and keep
the Damping factor of Second order system constant and observe the wave form at Vf by
varying P-Gain.
3. You can observe that as the P-Gain increases error decreases but oscillations increases. If
P gain is less, error is more but oscillations are less.
4. We can observe that the error voltage = G
Vs
1
5. Check with the Theoretical value and the practical result.
Proportional – Integral [PI] Controller
1. Make the connections as given in the circuit diagram - Keep D Controller at OFF
position.
2. Connect Square wave input to Second Order System for different Values of P and I gain
by keeping the damping factor constant by adjusting R value provided on the front panel
by varying both P gain and I gain.
3. Enter the results in the tabular column.
4. You can observe that study state error is zero with PI controller.
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
56 Control System Laboratory, EEE
(For CSE, ECE & EEE)
Proportional + Integral + Derivative [PID] Controller
1. Make the connections as given in the circuit diagram.
2. Connect square wave input to the Second order system and adjust damping factor by
adjusting R.
3. Observe the wave form at Input and VF. You can observe that by increasing the D gain
over shoots are minimizing.
CONNECTION DIAGRAM:
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
57 Control System Laboratory, EEE
(For CSE, ECE & EEE)
TABULAR COLUMN:
P – Controller
Sl.
No
P-
Gain
(G)
Set
voltage –
Vs
Feedback
voltage – VF
Error
voltage -
er
Calculated
error
=Vs/1+G
PI Controller
Sl.
No
P-
Gain
(G)
I-Gain
(G)
Set
voltage –
Vs
Feedback
voltage –
VF
Error
voltage -
er
Calculated
error
=Vs/1+G
PID Controller
Sl.
No
P-
Gain
(G)
I-Gain
(G)
D-Gain
(G)
Set
voltage –
Vs
Feedback
voltage
– VF
Error
voltag
e -er
Calculated
error
=Vs/1+G
RESULT:
VIVA QUESTIONS:
1. What is the effect of PI controller on the system performance?
2. What is the effect of P controller on the system performance?
3. What is the effect of PID controller on the system performance?
4. What are the disadvantages of P controller?
5. Define damping ratio?
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
58 Control System Laboratory, EEE
(For CSE, ECE & EEE)
EXPERIMENT NO. 12
LAG AND LEAD COMPENSATION –
MAGNITUDE AND PHASE PLOT
AIM: To obtain magnitude and phase plots of the given compensation networks and verify the
responses.
APPARATUS:
1. Lead-Lag Compensation Trainer Kit
2. Resistors
3. Capacitors
4. Patch Cords
CIRCUIT DIAGRAM:
Lag Compensator Lead Compensator
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
59 Control System Laboratory, EEE
(For CSE, ECE & EEE)
Lead - Lag Compensator
PROCEDURE:
1. Switch ON the Mains supply to the unit. Observe the sine wave signal by varying
frequency and amplitude potentiometer.
2. Now make the networks connections depending on Lag – Lead or Lag – Lead networks.
Connect sine wave output to networks input.
3. Note down the peak detector input using digital voltmeter provided. Now the frequency
and note down the frequency, Phase angle difference and output Vp for different
frequencies and enter the readings in the tabular column.
4. Now calculate the theoretical values of phase angle difference and gain. Compare this
with the measured values.
5. Plot the graph of Phase Angle Vs Frequency (Phase plot) and Gain Vs Frequency
(Magnitude plot).
6. Repeat the same for different frequencies.
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
60 Control System Laboratory, EEE
(For CSE, ECE & EEE)
TABULATION:
Sl.No. Frequency
(Hz)
Indicated Calculated
Φ Vout/Vin Φ
Vout/Vin
TABULATION:
Sl.No. Frequency
(Hz)
Indicated Calculated
Φ Vout/Vin Φ
Vout/Vin
MODEL CALCULATIONS:
In case of lag compensation network
G(S) = 1)(
1
21
2
csRR
csR =
Ts
Ts
1
1 =
)/1(
)/1(1
TS
TS
R2c = T; R1 + R2 = >1
G(jw) = 1
1222
22
T
T
- = Tan-1 wt – tan-1 wt
In case of lead compensation network
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
61 Control System Laboratory, EEE
(For CSE, ECE & EEE)
G (S) = 21
12 )1(
RR
csRR
21
21 1
RR
csRR
=)1(
)1(
TS
ST
=
)/1(
)/1(
TS
TS
G(jw) =
1
1222
22
T
T
G(jW) = tan-1 (wT) – tan-1 (wT)
CONNECTION DIAGRAM:
LAG COMPENSATION
LEAD
COMPEN
SATION
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
62 Control System Laboratory, EEE
(For CSE, ECE & EEE)
LEAD – LAG COMPENSATION
St.PETER’S ENGINEERING COLLEGE
(Sponsored by Shantha Educational Society)
(Approved by AICTE, New Delhi, Affiliated to JNTUH)
Giving Wings to Thoughts
Department of Electrical and Electronics Engineering
63 Control System Laboratory, EEE
(For CSE, ECE & EEE)
RESULT:
VIVA QUESTIONS:
1. What is compensator?
2. What is the difference between Lead and Lag compensator?
3. Bode plot for Lag network?
4. Which compensator used to improve study state response of system?
5. Which compensator used to improve transient response of system?
6. Which type of filter acts as a lead compensator?
7. Which compensator acts as a band pass filter?
8. Which compensator acts as a high pass filter?
Recommended