Digital Radio Receiver Amit Mane System Engineer

Digital Radio Receiver

Amit ManeSystem Engineer

Introduction

• Virtually all digital receivers perform channel access using DDC

• The desired channel is translated using the digital mixer comprised of multipliers and DDS

• The sample rate is then adjusted to match the channel bandwidth

– CIC filter

– Two poly phase decimators

Introduction

• The functions performed in the system are – Waveform synthesis (DDS)

– Complex multiplication

– Multirate filtering

• The overall sample rate change of the DDC is 120

• The DDS mixer has a SFDR of 102 dB

• The data rate can be upto 208 MHz

Introduction

• Innovative DRR System requires – One Quadia

– Two UWBs

• Number of channels implemented = 40

Complete System

Block diagram

Digital Receiver Block Diagram

A

10 channel

s of I/Q @

1.0833MSPS

16-bit

Clock circuitry

A/D12-bit

130/208 MSPS

A/D12-bit

130/208 MSPS

A

B

ClkCIC

30:1

NCO

MixerA/D Mux

RegistersA/D input select

Mixer FreqRev Code

StatusGainTest

20 channels of I/Q @ 4.33 MSPS

32--bit

J4Link

UWB1 of 2

CommandChannel

1 of 20 channels

A/D Intf

A/D Intf

Gain

PCI FPGA

DDR RAM16Mx16

DSP

Quadia Logic1 of 2

DSP

CFIR2:1

Overflowdetect

1 of 20 channels

Interrupts

Interrupts

Triggering

Spectral

invert

Register Spectral Inversion

20-bit

TestMux

TestGenerator

TestMux

RegisterTest Controls

2-bit

Dual QueueVFIFO

FIFO

Register Rev Codes

StatusRegister DCMs locked

Clock DCMIn = DSP1 EMIF Clk

Out = DSP1 EMIF Clk

Clock DCMIn = DSP2 EMIF Clk

Out = DSP2 EMIF Clk

DSP1 Registers

DSP2 Registers DRR FIFO Thresh

J4 link

Reset

Data Flow

Controller

Overflowdetect

FIFO

FIFO

10 channel

s of I/Q @

1.0833MSPS

16-bit

FIFO

PFIR2:1

TestGenerator

UWB

Filter Guide

Fs / 2=32500kHz

Fpass= 490kHz

Fstop1= 541.666kHz

Fstop2= 1350kHz

MATLAB Development System

DDC Frequency Response

MATLab SimuLink Development

• MATLab and Simulink used with Xilinx System Generator

• Simulink gateways provide connection to physical hardware and connect with Framework Logic

• End-to-end simulation under MATLab

• JTAG link allows real hardware to be tested from MATLab environment

• System Generator links Xilinx tools for chip design

Using Simulink and System Generator

• Simulink Block libraries are used to draw the system• Innovative BSP provides blocks for UWB components

• Simulink blocks for DSP, data generation and viewing

• Xilinx System Generator links all blocks

Starting a new design!

Simulink Libraries

• Board Support Package for CS includes hardware and signal processing components

• A/Ds, J4, DDCs ....

SimuLink Block Diagram

• The top level design has the Xilinx System Generator block for integration with logic tools

Top Level Design

Xilinx System Generator Integrates with Simulink

• Compiling and fitting the design is done directly from the Simulink environment

Design Using Simulink Blocks and Functions

• Large libraries of DSP and logic function may be directly used• Drag-n-drop from Simulink libraries

Validating the Design

• Validate the design by including the hardware in the Simulink • Hardware in the loop testing using JTAG

• Bit-true and cycle-true testing

The Real Hardware

Observe and analyze real data inside Simulink

Flow data from Simulink through the hardware and back to Simulink

Design Testing using Simulink

• Run real-time or Simulink test data through the actual design

Execution Control

VHDL Development Tools Flow

Quadia Application Logic Simulation

Multiple Channel on DSP 0

Ten Channels per DSP

Multiple Channel Operation

DSP 0

DSP 1

DSP 2

DSP 3

Spectral Inversion Testing

32.51 MHz Input32.52 MHz Tunefs = 129.843 MHz

Before Spectral Inversion...

9.7 kHz

32.51 MHz Input32.52 MHz Tunefs = 129.843 MHz

After Spectral Inversion...

Spectral Inversion Testing

531 kHz

Thank you !