View
1
Download
0
Category
Preview:
Citation preview
dummyheaddummyhead
HOW TO USE THIS MANUAL
HOW TO USE THIS MANUALA Few Words About SafetyService InformationThe service and repair information contained in this manual is intended for use by qualified, professional technicians. Attemptingservice or repairs without the proper training, tools, and equipment could cause injury to you or others. It could also damage thevehicle or create an unsafe condition.
This manual describes the proper methods and procedures for performing service, maintenance and repairs. Some proceduresrequire the use of specially designed tools and dedicated equipment. Any person who intends to use a replacement part, serviceprocedure or a tool that is not recommended by Honda, must determine the risks to their personal safety and the safe operation ofthe vehicle.
If you need to replace a part, use Honda Genuine parts with the correct part number or an equivalent part. We strongly recommendthat you do not use replacement parts of inferior quality.
For Your Customer’s SafetyProper service and maintenance are essential to the customer’s safety and the reliability of the vehicle. Any error or oversight whileservicing a vehicle can result in faulty operation, damage to the vehicle, or injury to others.
For Your SafetyBecause this manual is intended for the professional service technician, we do not provide warnings about many basic shop safetypractices (e.g., Hot parts–wear gloves). If you have not received shop safety training or do not feel confident about your knowledgeof safe servicing practice, we recommended that you do not attempt to perform the procedures described in this manual.
Some of the most important general service safety precautions are given below. However, we cannot warn you of every conceivable hazard that can arise in performing service and repair procedures. Only you can decide whether or not you shouldperform a given task.
Important Safety PrecautionsMake sure you have a clear understanding of all basic shop safety practices and that you are wearing appropriate clothing andusing safety equipment. When performing any service task, be especially careful of the following:
• Read all of the instructions before you begin, and make sure you have the tools, the replacement or repair parts, and the skillsrequired to perform the tasks safely and completely.
• Protect your eyes by using proper safety glasses, goggles or face shields any time you hammer, drill, grind, pry or work aroundpressurized air or liquids, and springs or other stored-energy components. If there is any doubt, put on eye protection.
• Use other protective wear when necessary, for example gloves or safety shoes. Handling hot or sharp parts can cause severeburns or cuts. Before you grab something that looks like it can hurt you, stop and put on gloves.
• Protect yourself and others whenever you have the vehicle up in the air. Any time you lift the vehicle, either with a hoist or a jack,make sure that it is always securely supported. Use jack stands.
Make sure the engine is off before you begin any servicing procedures, unless the instruction tells you to do otherwise. This willhelp eliminate several potential hazards:
• Carbon monoxide poisoning from engine exhaust. Be sure there is adequate ventilation whenever you run the engine • Burns from hot parts or coolant. Let the engine and exhaust system cool before working in those areas. • Injury from moving parts. If the instruction tells you to run the engine, be sure your hands, fingers and clothing are out of the way.
Gasoline vapors and hydrogen gases from batteries are explosive. To reduce the possibility of a fire or explosion, be careful whenworking around gasoline or batteries.
• Use only a nonflammable solvent, not gasoline, to clean parts. • Never drain or store gasoline in an open container. • Keep all cigarettes, sparks and flames away from the battery and all fuel-related parts.
Improper service or repairs can create an unsafe condition that can cause your customer or others to be seriously hurt or killed.
Follow the procedures and precautions in this manual and other service materials carefully.
Failure to properly follow instructions and precautions can cause you to be seriously hurt or killed.
Follow the procedures and precautions in this manual carefully.
0-1
dummyheaddummyhead
HOW TO USE THIS MANUAL
How To Use This ManualThis manual describes the service procedures for the CRF250L.
Sections 1 and 3 apply to the whole motorcycle. Section 2 illustrates procedures for removal/installation of components that may berequired to perform service described in the following sections.Section 4 through 20 describe parts of the motorcycle, grouped according to location.
Follow the Maintenance Schedule recommendations to ensure that the motorcycle is in peak operating condition.Performing the first scheduled maintenance is very important. It compensates for the initial wear that occurs during the break-inperiod.
Find the section you want on this page, then turn to the table of contents on the first page of the section.
Most sections start with an assembly or system illustration, service information and troubleshooting for the section. The subsequentpages give detailed procedure.
Refer to the troubleshooting in each section according to the malfunction or symptom. In case of an engine trouble, refer to PGM-FIsection troubleshooting first.
As you read this manual, you will find information that is preceded by a symbol. The purpose of this message is to help prevent damage to your vehicle, other property, or the environment.
© Honda Motor Co., Ltd.SERVICE PUBLICATION OFFICEDate of Issue: June, 2012
Your safety, and the safety of others, is very important. To help you make informed decisions we have provided safety messages and other information throughout this manual. Of course, it is not practical or possible to warn you about all the hazards associated with servicing this vehicle.You must use your own good judgement.You will find important safety information in a variety of forms including: • Safety Labels – on the vehicle • Safety Messages – preceded by a safety alert symbol and one of three signal words, DANGER, WARNING, or CAUTION.
These signal words mean:
You WILL be KILLED or SERIOUSLY HURT if you don’t follow instructions.
You CAN be KILLED or SERIOUSLY HURT if you don’t follow instructions.
You CAN be HURT if you don’t follow instructions. • Instructions – how to service this vehicle correctly and safely.
ALL INFORMATION, ILLUSTRATIONS, DIRECTIONS AND SPECIFICATIONS INCLUDED IN THIS PUBLICATION ARE BASED ON THE LATEST PRODUCT INFORMATION AVAILABLE AT THE TIME OF APPROVAL FOR PRINTING. Honda Motor Co., Ltd. RESERVES THE RIGHT TO MAKE CHANGES AT ANY TIME WITHOUT NOTICE AND WITHOUT INCURRING ANY OBLIGATION WHATSOEVER. NO PART OF THIS PUBLICATION MAY BE REPRODUCED WITHOUT WRITTEN PERMISSION. THIS MANUAL IS WRITTEN FOR PERSONS WHO HAVE ACQUIRED BASIC KNOWLEDGE OF MAINTENANCE ON Honda MOTORCYCLES, MOTOR SCOOTERS OR ATVS.
0-2
dummyheaddummyhead
HOW TO USE THIS MANUAL
SYMBOLSThe symbols used throughout this manual show specific service procedures. If supplementary information is required pertaining tothese symbols, it would be explained specifically in the text without the use of the symbols.
Replace the part(s) with new one(s) before assembly.
Use the recommend engine oil, unless otherwise specified.
Use molybdenum oil solution (mixture of the engine oil and molybdenum grease in a ratio of 1:1).
Use multi-purpose grease (lithium based multi-purpose grease NLGI #2 or equivalent).
Use molybdenum disulfide grease (containing more than 3% molybdenum disulfide, NLGI #2 or equivalent).Example: • Molykote® BR-2 plus manufactured by Dow Corning U.S.A. • Multi-purpose M-2 manufactured by Mitsubishi Oil, JapanUse molybdenum disulfide paste (containing more than 40% molybdenum disulfide, NLGI #2 or equivalent).Example: • Molykote® G-n Paste manufactured by Dow Corning U.S.A. • Honda Moly 60 (U.S.A. only) • Rocol ASP manufactured by Rocol Limited, U.K. • Rocol Paste manufactured by Sumico Lubricant, Japan
Use silicone grease.
Apply locking agent. Use a medium strength locking agent unless otherwise specified.
Apply sealant.
Use DOT 3 or DOT 4 brake fluid. Use the recommended brake fluid unless otherwise specified.
Use fork or suspension fluid.
0-3
CONTENTS
dummyheaddummyhead
GENERAL INFORMATION 1FRAME/BODY PANELS/EXHAUST SYSTEM 2MAINTENANCE 3
PGM-FI SYSTEM 4IGNITION SYSTEM 5ELECTRIC STARTER SYSTEM 6FUEL SYSTEM 7LUBRICATION SYSTEM 8COOLING SYSTEM 9CYLINDER HEAD/VALVES 10CYLINDER/PISTON 11CLUTCH/GEARSHIFT LINKAGE 12ALTERNATOR/STARTER CLUTCH 13CRANKCASE/CRANKSHAFT/TRANSMISSION/BALANCER 14ENGINE REMOVAL/INSTALLATION 15FRONT WHEEL/SUSPENSION/STEERING 16REAR WHEEL/SUSPENSION 17BRAKE SYSTEM 18BATTERY/CHARGING SYSTEM 19LIGHTS/METERS/SWITCHES 20WIRING DIAGRAM 21INDEX
dummyheaddummyhead
MEMO
dummytext
1. GENERAL INFORMATION
1
SERVICE RULES ··········································1-2
MODEL IDENTIFICATION ····························1-2
SPECIFICATIONS·········································1-4
TORQUE VALUES ········································1-9
LUBRICATION & SEAL POINTS ··············· 1-15
CABLE & HARNESS ROUTING················· 1-17
EMISSION CONTROL SYSTEMS ·············· 1-27
1-1
dummyheaddummyhead
GENERAL INFORMATION
GENERAL INFORMATIONSERVICE RULES1. Use genuine Honda or Honda-recommended parts and lubricants or their equivalents. Parts that do not meet Honda's design
specifications may cause damage to the motorcycle.2. Use the special tools designed for this product to avoid damage and incorrect assembly.3. Use only metric tools when servicing the motorcycle. Metric bolts, nuts and screws are not interchangeable with English
fasteners.4. Install new gaskets, O-rings, cotter pins, and lock plates when reassembling.5. When tightening bolts or nuts, begin with the larger diameter or inner bolt first. Then tighten to the specified torque diagonally in
incremental steps unless a particular sequence is specified.6. Clean parts in cleaning solvent upon disassembly. Lubricate any sliding surfaces before reassembly.7. After reassembly, check all parts for proper installation and operation.8. Route all electrical wires as shown in the Cable and Harness Routing (page 1-17).9. Do not bend or twist control cables. Damaged control cables will not operate smoothly and may stick or bind.
ABBREVIATIONThroughout this manual, the following abbreviations are used to identify the respective parts or systems.
DESTINATION CODEThroughout this manual, the following codes are used to identify individual types for each region.
MODEL IDENTIFICATION
Abbrev. term Full termCKP sensor Crankshaft Position sensorDLC Data Link ConnectorDTC Diagnostic Trouble CodeECM Engine Control ModuleECT sensor Engine Coolant Temperature sensorEEPROM Electrically Erasable Programmable Read Only MemoryIACV Idle Air Control ValveIAT sensor Intake Air Temperature sensorMAP sensor Manifold Absolute Pressure sensorMIL Malfunction Indicator LampPAIR Pulse Secondary Air InjectionPGM-FI Programmed Fuel InjectionSCS connector Service Check Short connectorTP sensor Throttle Position sensorVS sensor Vehicle Speed sensor
DESTINATION CODE REGION
E U.K.F FranceED European direct salesU Australia, New Zealand
1-2
dummyheaddummyhead
GENERAL INFORMATION
SERIAL NUMBERS/LABELS
The Vehicle Identification Number (V.I.N.) [1] is stamped on the right side of the steering head.
The throttle body identification number [1] is stamped on the lower left side of the throttle body.
The engine serial number [1] is stamped on the lower left side of the crankcase.
The Registered Number Plate (except U type) /Compliance plate (U type) [1] is stamped on the left front side of the steering head.
The color label [1] is attached on the frame behind rear brake master cylinder reservoir. When ordering color-coded parts, always specify the designated color code.
[1] [1]
[1]
[1]
[1]
1-3
dummyheaddummyhead
GENERAL INFORMATION
SPECIFICATIONSGENERAL SPECIFICATIONS
ITEM SPECIFICATIONDIMENSIONS Overall length 2,195 mm (86.4 in)
Overall width 815 mm (32.1 in)Overall height 1,195 mm (47.0 in)Wheelbase 1,445 mm (56.9 in)Seat height 875 mm (34.4 in)Footpeg height 365 mm (14.4 in)Ground clearance 255 mm (10.0 in)Curb weight 143 kg (315 lbs)Maximum weight capacity 159 kg (351 lbs)
FRAME Frame type Twin tubeFront suspension Telescopic forkFront axle travel 222 mm (8.7 in)Rear suspension SwingarmRear axle travel 240 mm (9.4 in)Tire size Front 3.00-21 51P
Rear 120/80-18M/C 62PTire brand Front GP-21F Z (IRC)
Rear GP-22R (IRC)Front brake Hydraulic single discRear brake Hydraulic single discCaster angle 27° 35’Trail length 113 mm (4.4 in)Fuel tank capacity 7.7 liter (2.03 US gal, 1.69 Imp gal)
ENGINE Cylinder arrangement Single cylinder inclined 20° from verticalBore and stroke 76.0 x 55.0 mm (2.99 x 2.17 in)Displacement 249.6 cm3 (15.23 cu-in)Compression ratio 10.7:1Valve train Chain driven DOHC with rocker armIntake valve opens at 1.0 mm (0.04 in) lift 20° BTDC
closes at 1.0 mm (0.04 in) lift 35° ABDCExhaust valve opens at 1.0 mm (0.04 in) lift 40° BBDC
closes at 1.0 mm (0.04 in) lift 0° TDCLubrication system Forced pressure and wet sumpOil pump type TrochoidCooling system Liquid cooledAir filtration Viscous paper filterEngine dry weight 34.5 kg (76.1 lbs)
FUEL DELIVERY SYSTEM
Type PGM-FIThrottle bore 36 mm (1.4 in)
DRIVE TRAIN Clutch system Multi-plate, wetClutch operation system Cable operatingTransmission Constant mesh, 6 speedsPrimary reduction 2.807 (73/26)Final reduction 2.857 (40/14)Gear ratio 1st 3.333 (40/12)
2nd 2.117 (36/17)3rd 1.571 (33/21)4th 1.304 (30/23)5th 1.115 (29/26)6th 0.962 (26/27)
Gearshift pattern Left foot operated return system1 - N - 2 - 3 - 4 - 5 - 6
ELECTRICAL Ignition system Computer-controlled digital transistorized with electric advance
Starting system Electric starter motorCharging system Triple phase output alternatorRegulator/rectifier SCR shorted, triple phase full-wave
rectificationLighting system Battery
1-4
dummyheaddummyhead
GENERAL INFORMATION
PGM-FI SYSTEM SPECIFICATIONS
IGNITION SYSTEM SPECIFICATIONS
ELECTRIC STARTER SPECIFICATIONUnit: mm (in)
FUEL SYSTEM SPECIFICATIONS
LUBRICATION SYSTEM SPECIFICATIONSUnit: mm (in)
ITEM SPECIFICATIONSFuel injector resistance (20°C/68°F) 11 – 13 Ω
ITEM SPECIFICATIONSpark plug SIMR8A9 (NGK)Spark plug gap 0.80 – 0.90 mm (0.031 – 0.035 in)Ignition coil peak voltage 100 V minimumCKP sensor peak voltage 0.7 V minimumIgnition timing ("F" mark) 10° BTDC at idle
ITEM STANDARD SERVICE LIMITStarter motor brush length 11.8 – 12.3 (0.46 – 0.48) 6.5 (0.26)
ITEM SPECIFICATIONSThrottle body identification number GQ32AEngine idle speed 1,450 ± 100 min-1 (rpm)Throttle grip freeplay 2 – 6 mm (0.08 – 0.24 in)Fuel pressure at idle 343 kPa (3.5 kgf/cm2, 50 psi)Fuel pump flow (at 12 V) 83 cm3 (2.81 US oz, 2.92 Imp oz) minimum/10 secondsPAIR control solenoid valve resistance (20°C/68°F) 20 – 24 Ω
ITEM STANDARD SERVICE LIMITEngine oil capacity At draining 1.4 liters (1.5 US qt, 1.2 Imp qt) –
At oil filter change 1.5 liters (1.6 US qt, 1.3 Imp qt) –At disassembly 1.8 liters (1.9 US qt, 1.6 Imp qt) –
Recommended engine oil Honda "4-stroke motorcycle oil" or an equivalentAPI classification: SG or higher (except oils labeled as energy conserving on the circular API service label)Viscosity: SAE 10W-30JASO T 903 standard: MA
–
Oil pump rotor Tip clearance 0.15 (0.006) 0.20 (0.008)Body clearance 0.15 – 0.22 (0.006 – 0.009) 0.35 (0.014)Side clearance 0.02 – 0.09 (0.001 – 0.004) 0.10 (0.004)
1-5
dummyheaddummyhead
GENERAL INFORMATION
COOLING SYSTEM SPECIFICATIONS
CYLINDER HEAD/VALVES SPECIFICATIONSUnit: mm (in)
CYLINDER/PISTON SPECIFICATIONSUnit: mm (in)
ITEM SPECIFICATIONSCoolant capacity Radiator and engine 1.02 liters (1.08 US qt, 0.90 Imp qt)
At draining 0.74 liter (0.78 US qt, 0.65 Imp qt)Reserve tank 0.16 liter (0.17 US qt, 0.14 Imp qt)
Radiator cap relief pressure 93.2 – 122.6 kPa (0.95 – 1.25 kgf/cm2, 13.5 – 17.8 psi)Thermostat Begin to open 81 – 84°C (178 – 183°F)
Fully open 95°C (203°F)Valve lift 4.5 mm (0.18 in) minimum
Recommended coolant High quality ethylene glycol antifreeze containing silicate-free corrosion inhibitors
Standard coolant concentration 1:1 (mixture with distilled water)
ITEM STANDARD SERVICE LIMITCylinder compression at 490 min-1 (rpm) 1,294 kPa (13.2 kgf/cm2, 188 psi) – Valve clearance IN 0.16 ± 0.03 (0.006 ± 0.001) –
EX 0.27 ± 0.03 (0.011 ± 0.001) – Valve, valve guide
Valve stem O.D. IN 4.475 – 4.490 (0.1762 – 0.1768) 4.46 (0.176)EX 4.465 – 4.480 (0.1758 – 0.1764) 4.45 (0.175)
Valve guide I.D. IN/EX 4.500 – 4.512 (0.1772 – 0.1776) 4.540 (0.1787)Stem-to-guide clearance
IN 0.010 – 0.037 (0.0004 – 0.0015) 0.07 (0.003)EX 0.020 – 0.047 (0.0008 – 0.0019) 0.08 (0.003)
Valve guide height IN/EX 13.8 – 14.0 (0.54 – 0.55) – Valve seat width IN/EX 0.90 – 1.10 (0.035 – 0.043) 1.50 (0.059)
Valve spring Free length Inner 34.58 (1.361) 32.85 (1.293)Outer 40.37 (1.589) 38.35 (1.510)
Rocker arm, rocker arm shaft
Arm I.D. IN/EX 10.000 – 10.015 (0.3937 – 0.3943) 10.10 (0.398)Shaft O.D. IN/EX 9.972 – 9.987 (0.3926 – 0.3932) 9.91 (0.390)Arm-to-shaft clearance IN/EX 0.013 – 0.043 (0.0005 – 0.0017) 0.10 (0.004)
Camshaft Cam lobe height IN 30.931 – 31.171 (1.2178 – 1.2272) 30.911 (1.2170)EX 30.839 – 31.079 (1.2141 – 1.2236) 30.819 (1.2133)
Camshaft journal O.D. 19.959 – 19.980 (0.7858 – 0.7866) – Oil clearance 0.020 – 0.062 (0.0008 – 0.0024) 0.10 (0.004)
Cylinder head
Camshaft journal area I.D. 20.000 – 20.021 (0.7874 – 0.7882) – Warpage – 0.05 (0.002)
ITEM STANDARD SERVICE LIMITCylinder I.D. 76.000 – 76.010 (2.9921 – 2.9925) 76.04 (2.994)
Out-of-round – 0.010 (0.0004)Taper – 0.010 (0.0004)Warpage – 0.05 (0.002)
Piston, piston pin, piston ring
Piston O.D. at 11 mm (0.4 in) from bottom 75.960 – 75.980 (2.9905 – 2.9913) 75.89 (2.988)
Piston pin hole I.D. 17.002 – 17.008 (0.6694 – 0.6696) 17.030 (0.6705)Piston pin O.D. 16.994 – 17.000 (0.6691 – 0.6693) 16.980 (0.6685)Piston-to-piston pin clearance 0.002 – 0.014 (0.0001 – 0.0006) 0.02 (0.001)Piston ring end gap
Top 0.28 – 0.38 (0.011 – 0.015) 0.40 (0.016)Second 0.40 – 0.55 (0.016 – 0.022) 0.70 (0.028)Oil (side rail) 0.20 – 0.70 (0.008 – 0.028) 1.10 (0.043)
Piston ring-to-ring groove clearance
Top 0.040 – 0.080 (0.0016 – 0.0031) 0.10 (0.004)Second 0.015 – 0.050 (0.0006 – 0.0020) 0.09 (0.004)
Cylinder-to-piston clearance 0.020 – 0.050 (0.0008 – 0.0020) 0.09 (0.004)Connecting rod small end I.D. 17.016 – 17.034 (0.6699 – 0.6706) 17.06 (0.672)Connecting rod-to-piston pin clearance 0.016 – 0.040 (0.0006 – 0.0016) 0.10 (0.004)
1-6
dummyheaddummyhead
GENERAL INFORMATION
CLUTCH/GEARSHIFT LINKAGE SPECIFICATIONS
Unit: mm (in)
ALTERNATOR/STARTER CLUTCH SPECIFICATIONSUnit: mm (in)
CRANKCASE/CRANKSHAFT/TRANSMISSION/BALANCER SPECIFICATIONSUnit: mm (in)
ITEM STANDARD SERVICE LIMITClutch lever freeplay 10 – 20 (0.4 – 0.8) –Clutch Spring free length 41.5 (1.63) 37.5 (1.48)
Disc thickness Disc A/B 2.30 – 2.50 (0.091 – 0.098) 2.27 (0.089)Plate warpage Plate A/B – 0.30 (0.012)
Clutch outer guide I.D. 20.000 – 20.021 (0.7874 – 0.7882) 20.04 (0.789)Mainshaft O.D. at clutch outer guide 19.967 – 19.980 (0.7861 – 0.7866) 19.947 (0.7853)
ITEM STANDARD SERVICE LIMITStarter driven gear I.D. 34.000 – 34.013 (1.3386 – 1.3391) 34.033 (1.3399)
O.D. 51.705 – 51.718 (2.0356 – 2.0361) 51.685 (2.0348)
ITEM STANDARD SERVICE LIMITCrankshaft Runout – 0.03 (0.001)
Connecting rod big end radial clearance 0.004 – 0.016 (0.0002 – 0.0006) 0.05 (0.002)Connecting rod big end side clearance 0.05 – 0.50 (0.002 – 0.020) 0.85 (0.033)Main journal oil clearance 0.018 – 0.045 (0.0007 – 0.0018) 0.075 (0.0030)Main journal O.D. 33.985 – 34.000 (1.3380 – 1.3386) 33.975 (1.3376)
Main journal bearing support I.D. 38.000 – 38.018 (1.4961 – 1.4968) 38.036 (1.4975)Transmission Gear I.D. M5, M6 23.000 – 23.021 (0.9055 – 0.9063) 23.07 (0.908)
C1 23.020 – 23.041 (0.9063 – 0.9071) 23.09 (0.909)C2 25.000 – 25.021 (0.9843 – 0.9851) 25.04 (0.986)C3, C4 28.000 – 28.021 (1.1024 – 1.1032) 28.04 (1.104)
Bushing O.D. M5, M6 22.959 – 22.980 (0.9039 – 0.9047) 22.91 (0.902)C1 22.984 – 23.005 (0.9049 – 0.9057) 22.47 (0.885)C2 24.959 – 24.980 (0.9826 – 0.9835) 24.90 (0.980)C3, C4 27.959 – 27.980 (1.1007 – 1.1016) 27.95 (1.100)
Gear-to-bushing clearance
M5, M6, C2, C3, C4 0.020 – 0.062 (0.0008 – 0.0024) 0.10 (0.004)
C1 0.015 – 0.057 (0.0006 – 0.0022) 0.10 (0.004)Bushing I.D. M5, C1 20.000 – 20.021 (0.7874 – 0.7882) 20.05 (0.789)
C2 22.000 – 22.021 (0.8661 – 0.8670) 22.07 (0.869)C3 25.000 – 25.021 (0.9843 – 0.9851) 25.04 (0.986)
Mainshaft / countershaft O.D.
at M5 bushing 19.959 – 19.980 (0.7858 – 0.7866) 19.91 (0.784)at C1 bushing 19.959 – 19.980 (0.7858 – 0.7866) 19.91 (0.784)at C2 bushing 21.959 – 21.980 (0.8645 – 0.8654) 21.91 (0.863)at C3 bushing 24.959 – 24.980 (0.9826 – 0.9835) 24.90 (0.980)
Bushing-to-shaft clearance M5, C1, C2, C3 0.020 – 0.062 (0.0008 – 0.0024) 0.10 (0.004)
Shift fork, shift fork shaft
Shift fork shaft O.D. 11.957 – 11.968 (0.4707 – 0.4712) 11.95 (0.470)Shift fork I.D. 12.000 – 12.018 (0.4724 – 0.4731) 12.05 (0.474)Shift fork claw thickness 4.93 – 5.00 (0.194 – 0.197) 4.82 (0.190)
Shift drum Shift drum O.D. Left side 13.966 – 13.984 (0.5498 – 0.5506) 13.94 (0.549)Shift drum journal I.D. Left side 14.000 – 14.027 (0.5512 – 0.5522) 14.06 (0.554)
Shift drum-to-shift drum journal clearance
Left side 0.016 – 0.061 (0.0006 – 0.0024) 0.08 (0.003)
1-7
dummyheaddummyhead
GENERAL INFORMATION
FRONT WHEEL/SUSPENSION/STEERING SPECIFICATIONS
Unit: mm (in)
REAR WHEEL/SUSPENSION SPECIFICATIONSUnit: mm (in)
BRAKE SYSTEM SPECIFICATIONSUnit: mm (in)
ITEM STANDARD SERVICE LIMITMinimum tire thread depth – 3.0 (0.12)Cold tire pressure Driver only 150 kPa (1.50 kgf/cm2, 22 psi) –
Driver and passenger 150 kPa (1.50 kgf/cm2, 22 psi) –Axle runout – 0.2 (0.01)Wheel rim runout Radial – 2.0 (0.08)
Axial – 2.0 (0.08)Wheel hub-to-rim distance 23.45 ± 1.0 (0.92 ± 0.04) –Fork Spring free length (Right side only) 575.0 (22.64) –
Pipe runout – 0.20 (0.008)Recommended fork fluid Honda ULTRA CUSHION OIL 10W or
equivalent –
Fluid level Right 122 (4.8) –Left 38 (1.5)
Fluid capacity Right 658 ± 2.5 cm3 (22.3 ± 0.08 US oz, 23.2 ± 0.09 Imp oz) –
Left 683 ± 2.5 cm3 (23.1 ± 0.08 US oz, 24.0 ± 0.09 Imp oz)
Steering head bearing pre-load 10.6 – 21.2 N (1.08 – 2.16 kgf, 2.38 – 4.77 lbf)
–
ITEM STANDARD SERVICE LIMITMinimum tire thread depth – 3.0 (0.12)Cold tire pressure Driver only 150 kPa (1.50 kgf/cm2, 22 psi) –
Driver and passenger 150 kPa (1.50 kgf/cm2, 22 psi) –Axle runout – 0.2 (0.01)Wheel rim runout Radial – 2.0 (0.08)
Axial – 2.0 (0.08)Wheel hub-to-rim distance 26.9 ± 1.0 (1.06 ± 0.04) –Drive chain Size/link DID520VF-106LE –
Slack 25 – 35 (1.0 – 1.4) –
ITEM STANDARD SERVICE LIMITFront Specified brake fluid DOT 3 or DOT 4 –
Brake pad wear indicator – To grooveBrake disc thickness 3.3 – 3.7 (0.13 – 0.15) 3.0 (0.12)Brake disc warpage – 0.3 (0.01)Master cylinder I.D. 12.700 – 12.743 (0.5000 – 0.5017) 12.755 (0.5022)Master piston O.D. 12.657 – 12.684 (0.4983 – 0.4994) 12.645 (0.4978)Caliper cylinder I.D. 27.000 – 27.050 (1.0630 – 1.0650) 27.060 (1.0654)Caliper piston O.D. 26.935 – 26.968 (1.0604 – 1.0617) 26.89 (1.0587)
Rear Specified brake fluid DOT 3 or DOT 4 –Brake pad wear indicator – To grooveBrake disc thickness 4.3 – 4.7 (0.17 – 0.19) 4.0 (0.16)Brake disc warpage – 0.3 (0.01)Master cylinder I.D. 12.700 – 12.743 (0.5000 – 0.5017) 12.755 (0.5022)Master piston O.D. 12.657 – 12.684 (0.4983 – 0.4994) 12.645 (0.4978)Caliper cylinder I.D. 27.000 – 27.050 (1.0630 – 1.0650) 27.060 (1.0654)Caliper piston O.D. 26.935 – 26.968 (1.0604 – 1.0617) 26.89 (1.0587)Brake pedal height 64 – 65 (2.52 – 2.56) –
1-8
dummyheaddummyhead
GENERAL INFORMATION
BATTERY/CHARGING SYSTEM SPECIFICATIONS
LIGHTS/METERS/SWITCHES SPECIFICATIONS
TORQUE VALUESSTANDARD TORQUE VALUES
ITEM SPECIFICATIONSBattery Type YTX7L-BS
Capacity 12 V - 6 Ah (10 HR)Current leakage 0.34 mA max.Voltage (20°C/68°F)
Fully charged 13.0 – 13.2 VNeeds charging Below 12.3 V
Charging current Normal 0.6 A/5 – 10 hQuick 3 A/1 h
Alternator Capacity 0.34 kW/5,000 min-1 (rpm)Charging coil resistance (20°C/68°F) 0.1 – 1.0 Ω
ITEM SPECIFICATIONBulbs Headlight 12 V - 60/55 W
Position light 12 V - 5 WBrake/taillight 12 V - 21/5 WFront turn signal light 12 V - 21 W x 2Rear turn signal light 12 V - 21 W x 2Instrument light LEDTurn signal indicator LEDHigh beam indicator LEDNeutral indicator LEDMIL LED
Fuse Main fuse 30 ASub fuse 10 A x 5, 5 A x 1
FASTENER TYPE TORQUE FASTENER TYPE TORQUEN·m (kgf·m, lbf·ft) N·m (kgf·m, lbf·ft)5 mm bolt and nut 5.2 (0.5, 3.8) 5 mm screw 4.2 (0.4, 3.1)6 mm bolt and nut(Include SH flange bolt)
10 (1.0, 7) 6 mm screw 9.0 (0.9, 6.6)6 mm flange bolt (8 mm head, large flange) and nut 12 (1.2, 9)8 mm bolt and nut 22 (2.2, 16)
10 mm bolt and nut 34 (3.5, 25) 8 mm flange bolt and nut 27 (2.8, 20)12 mm bolt and nut 54 (5.5, 40) 10 mm flange bolt and nut 39 (4.0, 29)
1-9
dummyheaddummyhead
GENERAL INFORMATION
ENGINE & FRAME TORQUE VALUES • Torque specifications listed below are for important fasteners. • Others should be tightened to standard torque values listed above.
FRAME/BODY PANELS/EXHAUST SYSTEM
MAINTENANCE
PGM-FI SYSTEM
ITEM Q'TY THREAD TORQUE REMARKSDIA. (mm) N·m (kgf·m, lbf·ft)Hook bolt 4 8 21 (2.1, 15)Left side cover assembly screw 2 4 0.9 (0.1, 0.7)Right fuel tank shroud assembly screw 4 4 0.9 (0.1, 0.7)Left fuel tank shroud assembly screw 2 4 0.9 (0.1, 0.7)Headlight cowl mounting bolt 4 6 8.5 (0.9, 6.3)Rear side reflector mounting nut (U type only)
2 6 1.5 (0.2, 1.1) U-nut
Rear reflector mounting nut 1 5 1.5 (0.2, 1.1) U-nutBrake/taillight mounting screw 3 6 4.5 (0.5, 3.3)Exhaust pipe protector socket bolt 2 6 12 (1.2, 9)Muffler protector cover screw 5 4 1.5 (0.2, 1.1)Muffler front mounting bolt 1 8 32 (3.3, 24)Muffler band bolt 1 8 22.5 (2.3, 17)Exhaust pipe joint nut 2 8 18 (1.8, 13)Exhaust pipe stud bolt 2 8 – See page 2-11Air cleaner connecting hose band screw 1 4 1.5 (0.2, 1.1)Sub-frame upper mounting nut 2 8 27 (2.8, 20)Sub-frame lower mounting bolt 2 8 27 (2.8, 20)Rear master cylinder reservoir mounting bolt
1 6 10 (1.0, 7)
Sidestand pivot bolt 1 10 10 (1.0, 7) See page 2-14Sidestand pivot lock nut 1 10 30 (3.1, 22) U-nut, See page 2-14
ITEM Q'TY THREAD TORQUE REMARKSDIA. (mm) N·m (kgf·m, lbf·ft)Throttle cable A adjuster lock nut (throttle body side) 1 6 3.0 (0.3, 2.2)Air cleaner cover screw 4 5 1.2 (0.1, 0.9)Spark plug 1 10 16 (1.6, 12)Crankshaft hole cap 1 30 8.0 (0.8, 5.9) Apply engine oil to the
threads.Timing hole cap 1 14 6.0 (0.6, 4.4) Apply engine oil to the
threads.Engine oil drain bolt 1 12 24 (2.4, 18)Drive chain adjuster lock nut 2 8 27 (2.8, 20) UBS nutRear axle nut 1 16 88 (9.0, 65) U-nutDrive sprocket fixing plate bolt 2 6 10 (1.0, 7)Driven sprocket nut 6 10 50 (5.1, 37) U-nutRear master cylinder reservoir mounting bolt
1 6 10 (1.0, 7)
Master cylinder reservoir cover screw 4 4 1.5 (0.2, 1.1)Rear master cylinder push rod lock nut 1 8 17.2 (1.8, 13)Front spoke 36 BC 3.2 3.7 (0.4, 2.7)Rear spoke 32 BC 3.2 3.7 (0.4, 2.7)
ITEM Q'TY THREAD TORQUE REMARKSDIA. (mm) N·m (kgf·m, lbf·ft)Sensor unit torx screw 3 5 3.4 (0.3, 2.5)ECT sensor 1 12 25 (2.5, 18)O2 sensor 1 12 25 (2.5, 18)Bank angle sensor mounting nut 2 6 9.0 (0.9, 6.6)
1-10
dummyheaddummyhead
GENERAL INFORMATION
IGNITION SYSTEM
ELECTRIC STARTER
FUEL SYSTEM
COOLING SYSTEM
CYLINDER HEAD/VALVES
CYLINDER/PISTON
ITEM Q'TY THREAD TORQUE REMARKSDIA. (mm) N·m (kgf·m, lbf·ft)Timing hole cap 1 14 6.0 (0.6, 4.4) Apply engine oil to the
threads.
ITEM Q'TY THREAD TORQUE REMARKSDIA. (mm) N·m (kgf·m, lbf·ft)Negative brush screw 1 5 3.7 (0.4, 2.7)Starter motor assembly bolt 2 5 4.9 (0.5, 3.6)
ITEM Q'TY THREAD TORQUE REMARKSDIA. (mm) N·m (kgf·m, lbf·ft)Fuel pump mounting nut 6 6 12 (1.2, 9) For tightening sequence
(page 7-9).Air cleaner housing mounting bolt 3 6 7.0 (0.7, 5.2)Insulator band screw 2 5 4.2 (0.4, 3.1) See page 7-13Air cleaner connecting hose band screw 1 4 1.5 (0.2, 1.1)Throttle cable stay screw 2 5 3.4 (0.3, 2.5)Clamp stay screw 1 5 3.4 (0.3, 2.5)Throttle cable A joint nut (grip side) 1 10 1.5 (0.2, 1.1)Throttle cable B joint nut (grip side) 1 12 1.5 (0.2, 1.1)Throttle cable B nut (throttle body side) 1 6 3.0 (0.3, 2.2)Injector joint mounting bolt 2 5 5.1 (0.5, 3.8)IACV setting plate torx screw 2 4 2.1 (0.2, 1.5)PAIR check valve cover bolt 2 5 5.2 (0.5, 3.8)
ITEM Q'TY THREAD TORQUE REMARKSDIA. (mm) N·m (kgf·m, lbf·ft)Water hose band screw 4 – – See page 9-7Fan motor shroud mounting bolt 3 6 8.5 (0.9, 6.3)Fan motor screw 3 4 2.7 (0.3, 2.0)Cooling fan nut 1 3 1.0 (0.1, 0.7) Apply locking agent to the
threads.Water pump impeller 1 7 10 (1.0, 7)
ITEM Q'TY THREAD TORQUE REMARKSDIA. (mm) N·m (kgf·m, lbf·ft)Cylinder head cover bolt 2 6 10 (1.0, 7)Camshaft holder mounting bolt 8 6 12 (1.2, 9) Apply engine oil to the threads
and seating surface.Cylinder head mounting nut 4 10 45 (4.6, 33) Apply engine oil to the threads
and seating surface.Cam chain tensioner lifter plug 1 6 4.2 (0.4, 3.1)
ITEM Q'TY THREAD TORQUE REMARKSDIA. (mm) N·m (kgf·m, lbf·ft)Cylinder stud bolt 4 10 – See page 11-4Cam chain tensioner lifter plug 1 6 4.2 (0.4, 3.1)
1-11
dummyheaddummyhead
GENERAL INFORMATION
CLUTCH/GEARSHIFT LINKAGE
ALTERNATOR/STARTER CLUTCH
CRANKCASE/CRANKSHAFT/TRANSMISSION/BALANCER
ENGINE REMOVAL/INSTALLATION
ITEM Q'TY THREAD TORQUE REMARKSDIA. (mm) N·m (kgf·m, lbf·ft)Clutch center lock nut 1 16 108 (11.0, 80) Lock nut; replace with a new
one and stake.Apply engine oil to the threads and seating surface.
Clutch lifter plate bolt 5 6 12 (1.2, 9)Shift drum stopper plate bolt 1 6 10 (1.0, 7) Apply locking agent to the
threads.Shift drum stopper arm bolt 1 6 10 (1.0, 7) Apply locking agent to the
threads.Gearshift spindle return spring pin 1 8 30 (3.1, 22) Apply locking agent to the
threads.Primary drive gear lock nut 1 16 108 (11.0, 80) Apply engine oil to the threads
and seating surface.
ITEM Q'TY THREAD TORQUE REMARKSDIA. (mm) N·m (kgf·m, lbf·ft)Stator mounting socket bolt 3 6 10 (1.0, 7)CKP sensor mounting socket bolt 2 6 10 (1.0, 7) Apply locking agent to the
threads.Coating width: 6.5 ± 1.0 mm (0.26 ± 0.04 in) from tip
Flywheel bolt 1 12 128 (13.1, 94) Apply engine oil to the threads and seating surface.
Starter clutch socket bolt 6 8 30 (3.1, 22) Apply locking agent to the threads.
ITEM Q'TY THREAD TORQUE REMARKSDIA. (mm) N·m (kgf·m, lbf·ft)Balancer shaft nut 1 14 44 (4.5, 32) Apply engine oil to the threads
and seating surface.Cam chain tensioner pivot bolt 1 6 10 (1.0, 7) Apply locking agent to the
threads.Coating width: 6.5 ± 1.0 mm (0.26 ± 0.04 in) from tip
ITEM Q'TY THREAD TORQUE REMARKSDIA. (mm) N·m (kgf·m, lbf·ft)Rear engine mounting nut 2 10 45 (4.6, 33)Front engine mounting nut 2 10 55 (5.6, 41)Engine hanger plate bolt 2 8 27 (2.8, 20)Drive sprocket fixing plate bolt 2 6 10 (1.0, 7)
1-12
dummyheaddummyhead
GENERAL INFORMATION
FRONT WHEEL/SUSPENSION/STEERING
REAR WHEEL/SUSPENSION
ITEM Q'TY THREAD TORQUE REMARKSDIA. (mm) N·m (kgf·m, lbf·ft)Front axle bolt 1 14 73.5 (7.5, 54)Front axle pinch bolt 2 8 20 (2.0, 15)Front brake disc bolt 6 6 20 (2.0, 15) ALOC bolt; replace with a new
one.Front spoke 36 BC 3.2 3.7 (0.4, 2.7)Top bridge pinch bolt 4 8 32 (3.3, 24)Bottom bridge pinch bolt 4 8 32 (3.3, 24)Front brake hose guide bolt 2 6 10 (1.0, 7)Front brake hose clamp bolt 2 6 10 (1.0, 7)Fork protector socket bolt 6 6 7.0 (0.7, 5.2) ALOC bolt; replace with a new
one.Front brake caliper mounting bolt 2 8 30 (3.1, 22) ALOC bolt; replace with a new
one.Fork center bolt 1 8 20 (2.0, 15) Apply locking agent to the
threads.Fork rod lock nut (Right side) 1 10 20 (2.0, 15)Fork inner damper rod lock nut (Left side) 1 10 20 (2.0, 15)Fork cap 2 50 35 (3.6, 26)Handlebar switch housing screw 4 5 2.5 (0.3, 1.8)Front master cylinder holder bolt 2 6 9.8 (1.0, 7.2)Steering stem adjusting nut 1 26 – Apply engine oil to the
threads.See page 16-24
Steering stem nut 1 24 103 (10.5, 76) See page 16-24Clutch lever pivot bolt 1 6 1.0 (0.1, 0.7) Apply grease to the sliding
surface.Clutch lever pivot nut 1 6 5.9 (0.6, 4.4)
ITEM Q'TY THREAD TORQUE REMARKSDIA. (mm) N·m (kgf·m, lbf·ft)Rear axle nut 1 16 88 (9.0, 65) U-nutDriven sprocket nut 6 10 50 (5.1, 37) U-nutRear brake disc bolt 4 8 42 (4.3, 31) ALOC bolt; replace with a new
one.Rear spoke 32 BC 3.2 3.7 (0.4, 2.7)Shock absorber upper mounting nut 1 10 54 (5.5, 40) U-nutShock absorber lower mounting nut 1 10 44 (4.5, 32) U-nutShock link nut 2 10 44 (4.5, 32) U-nutShock arm-to-swingarm nut 1 12 74 (7.5, 55) U-nut
Apply engine oil to the threads.
Swingarm pivot nut 1 14 88 (9.0, 65) U-nutRear brake hose guide mounting screw 2 5 1.2 (0.1, 0.9)Chain slider mounting screw 4 5 4.2 (0.4, 3.1) ALOC screw; replace with a
new one.Chain case stay mounting screw 1 6 4.2 (0.4, 3.1) ALOC screw; replace with a
new one.Chain guide mounting bolt 2 6 10 (1.0, 7) ALOC bolt; replace with a new
one.Chain slider guide mounting nut 2 6 2.5 (0.3, 1.8) U-nut
1-13
dummyheaddummyhead
GENERAL INFORMATION
BRAKE SYSTEM
BATTERY/CHARGING SYSTEM
LIGHTS/METERS/SWITCHES
ITEM Q'TY THREAD TORQUE REMARKSDIA. (mm) N·m (kgf·m, lbf·ft)Brake caliper bleed valve 2 8 5.4 (0.6, 4.0)Master cylinder reservoir cover screw 4 4 1.5 (0.2, 1.1)Rear master cylinder reservoir mounting bolt
1 6 10 (1.0, 7)
Front brake pad pin 1 10 17.2 (1.8, 13)Rear brake pad pin 1 10 17.2 (1.8, 13)Brake hose oil bolt 4 10 34 (3.5, 25)Front master cylinder holder bolt 2 6 9.8 (1.0, 7.2)Front brake light switch screw 1 4 1.2 (0.1, 0.9)Rear master cylinder mounting bolt 2 6 14 (1.4, 10) ALOC bolt; replace with a new
one.Rear master cylinder push rod lock nut 1 8 17.2 (1.8, 13)Brake lever pivot bolt 1 6 1.0 (0.1, 0.7) Apply 0.1 g (0.004 oz) of
silicone grease to the sliding surface.
Brake lever pivot nut 1 6 5.9 (0.6, 4.4)Front brake caliper mounting bolt 2 8 30 (3.1, 22) ALOC bolt; replace with a new
one.Front brake caliper bracket pin 1 8 17.2 (1.8, 13)Rear brake reservoir stay mounting screw
1 6 1.5 (0.2, 1.1)
ITEM Q'TY THREAD TORQUE REMARKSDIA. (mm) N·m (kgf·m, lbf·ft)Battery holder plate bolt 2 6 7.0 (0.7, 5.2)
ITEM Q'TY THREAD TORQUE REMARKSDIA. (mm) N·m (kgf·m, lbf·ft)Headlight unit mounting screw 4 5 1.2 (0.1, 0.9)Turn signal unit mounting nut 4 10 21 (2.1, 15)Brake/taillight mounting screw 3 6 4.5 (0.5, 3.3)Hook bolt 4 8 21 (2.1, 15)Speedometer mounting screw 3 5 1.0 (0.1, 0.7)Ignition switch mounting bolt 2 8 24 (2.4, 18) One-way bolt; replace with a
new one.Neutral switch 1 10 12 (1.2, 9)Sidestand switch mounting bolt 1 6 10 (1.0, 7) ALOC bolt; replace with a new
one.
1-14
dummyheaddummyhead
GENERAL INFORMATION
LUBRICATION & SEAL POINTSENGINE
MATERIAL LOCATION REMARKSLiquid sealant (Three bond 1207B, 1215 or equivalent)
Left crankcase mating surface See page 14-18Alternator/CKP sensor wire grommet sealing surface
Liquid sealant (Three bond 5211C, 1207B, 1215, SS KE45 or equivalent)
Cylinder head semi-circular cut-out
Engine oil Oil pump rotor entire surfaceOil pump shaft outer surfaceWater pump shaft outer surfaceCam chain whole surfaceCylinder inner surfacePiston pin hole inner surface, ring groove and sliding surfacePiston ring entire surfaceClutch disc entire surfaceGearshift spindle shaft outer surfaceStarter one-way clutch spragStarter driven gear sliding surfaceEach oil seal lipsEach bearing rotating areaEach gear teethEach O-ring
Multi-purpose grease Each oil seal lips (clutch lifter arm, gearshift spindle, countershaft, water pump)
Molybdenum oil solution (a mixture of 1/2 engine oil and 1/2 molybdenum disulfide grease)
Valve stem sliding surfaceCamshaft lobes and journalRocker arm shaft outer surfaceRocker arm inner surface, roller surface and slipper surfacePiston pin outer surfaceClutch outer guide whole surfaceClutch lifter arm sliding surfaceStarter reduction gear inner surfaceStarter reduction gear shaft outer surfaceCrankshaft main journal bearing sliding surfaceConnecting rod big end sliding surfaceConnecting rod small end inner surfaceLeft crankshaft needle bearing rotating surfaceBalancer driven gear and sub gear sliding surfaceShift fork inner surface and guide pinShift fork shaft outer surfaceShift drum journal outer surface and groovesM5, C1, C2, C3 gear bushing entire surfaceM6, C4 gear bushing outer surface
Locking agent Mainshaft bearing setting plate bolt threads Coating width: 6.5 ± 1.0 mm (0.26 ± 0.04 in) from tip
1-15
dummyheaddummyhead
GENERAL INFORMATION
FRAME
MATERIAL LOCATION REMARKSUrea based multi-purpose grease with extreme pressure agent (example: Kyodo Yushi, EXCELITE EP2 or equivalent)
Steering head bearing inner race and outer race rolling surface 3 – 5 g (0.11 – 0.18 oz)Steering head bearing dust seal lips
Multi-purpose grease Sidestand pivot sliding surfaceAxle outer surface Throttle pipe flange cable grooveShock linkage needle bearing rotating areaShock linkage collar whole surfaceSwingarm pivot needle bearing rotating areaSwingarm pivot collar whole surfaceSwingarm pivot bolt outer surfaceSwingarm cap lipsGap between the swingarm caps, pivot collar and bearingsBrake pedal pivot sliding areaMain step pivot pin sliding areaPillion step pivot pin sliding surfaceEach dust seal lipsEach O-ring
Silicone grease Brake pad pin stopper ring surfaceBrake caliper bracket pin boots 0.4 g (0.01 oz) minimumBrake caliper dust seal whole surfaceBrake lever contacting area with master piston 0.1 g (0.004 oz)Rear master cylinder push rod contacting area with master cylinder piston and boot 0.1 g (0.004 oz)Master cylinder boot 0.1 g (0.004 oz)
DOT 3 or DOT 4 brake fluid Brake master piston sliding area and piston cupsRear master cylinder hose joint O-ringBrake caliper piston sliding area and piston seal
Fork fluid Fork cap O-ringFork oil seal lipsFork dust seal lipsFork guide bushing and slider bushing surface
Honda Bond A or equivalent Left handlebar and throttle pipe outer surface (grip rubber contacting area)Air cleaner connecting hose mating surface with air cleaner housingSwingarm rubber cap mating surface with swingarm
1-16
dummyheaddummyhead
GENERAL INFORMATION
CABLE & HARNESS ROUTING
CLUTCH CABLE
LEFT HANDLEBAR SWITCH WIRE
THROTTLE CABLES
RIGHT HANDLEBAR SWITCH WIRE
FRONT BRAKE HOSE
THROTTLE CABLES
FRONT BRAKE HOSE
HANDLEBAR SWITCH WIRE
HANDLEBAR
WIRE BANDS
Front
Align the lower end of outer rubber with the lower end of hose clamp.
25° – 30°
1-17
dummyheaddummyhead
GENERAL INFORMATION
SPEEDOMETER 16P CONNECTOR BOOT
CLUTCH CABLE
LEFT HANDLEBAR SWITCH 14P (GRAY) CONNECTOR
THROTTLE CABLES
RIGHT HANDLEBAR SWITCH WIRE
FRONT BRAKE HOSE
RIGHT HANDLEBAR SWITCH 9P (BLACK) CONNECTOR
IGNITION SWITCH WIRE
IGNITION SWITCH WIRE
HEADLIGHT 3P (BLACK) CONNECTOR
WIRE CLAMP
WIRE CLAMP
IGNITION SWITCH 3P (BROWN) CONNECTOR
CONNECTORS:– RIGHT FRONT TURN SIGNAL 2P (LIGHT BLUE)– LEFT FRONT TURN SIGNAL 2P (ORANGE)
LEFT FRONT TURN SIGNAL 2P (ORANGE) CONNECTOR
RIGHT FRONT TURN SIGNAL 2P (LIGHT BLUE) CONNECTOR
RIGHT FRONT TURN SIGNAL WIRE
LEFT FRONT TURN SIGNAL WIRE
METER STAY
SPEEDOMETER
LEFT FRONT TURN SIGNAL WIRE
IGNITION SWITCH WIRE MAIN WIRE
HARNESS
METER STAY
Viewed from the front side:
Viewed from the upper side: Viewed from the right side:
POSITION LIGHT 2P (BLACK) CONNECTOR
1-18
dummyheaddummyhead
GENERAL INFORMATION
CLUTCH CABLE
THROTTLE CABLES
RADIATOR SIPHON HOSE
RESERVE TANK OVERFLOW HOSE
WATER HOSE BAND
Front
0°± 30°
1-19
dummyheaddummyhead
GENERAL INFORMATION
ECM 33P (BLACK) CONNECTORGROUND POINT
BANK ANGLE SENSOR 2P CONNECTOR
PAIR CONTROL SOLENOID VALVE 2P (BLACK) CONNECTOR
TURN SIGNAL RELAY 3P (BLACK) CONNECTOR
JUNCTION BOX
REGULATOR/RECTIFIER 5P CONNECTOR
FUEL HOSE
FUEL PUMP 3P (BLACK) CONNECTOR
RADIATOR SIPHON HOSE
1-20
dummyheaddummyhead
GENERAL INFORMATION
GROUND POINT
PAIR AIR SUCTION HOSE
PAIR AIR SUCTION HOSE
PAIR AIR SUCTION HOSE
RESERVE TANK OVERFLOW HOSE
CRANKCASE BREATHER HOSE
CLUTCH CABLE
RESERVE TANK OVERFLOW HOSE
WIRE BAND GUIDE
WIRE BAND
Viewed from the front side:
Viewed from the front side:
VS SENSOR
CRANKCASE BREATHER HOSE
HOSE CLAMPS
REAR BRAKE LIGHT SWITCH WIRE
VS SENSOR 3P (BLUE) CONNECTOR
PAIR AIR SUPPLY HOSE
1-21
dummyheaddummyhead
GENERAL INFORMATION
CLUTCH CABLE
THROTTLE CABLES
RADIATOR SIPHON HOSE
RESERVE TANK OVERFLOW HOSE
PAIR AIR SUCTION HOSE
PAIR AIR SUPPLY HOSE
FUEL PUMP 3P (BLACK) CONNECTOR
IACV 4P (BLACK) CONNECTOR
FUEL INJECTOR 2P (GRAY) CONNECTOR
SPARK PLUG WIRE
FUEL TANK BREATHER HOSE (To FUEL TANK)
FUEL TANK BREATHER HOSE
FUEL TANK BREATHER HOSESUB-FRAME
Right
HOSE BAND
1-22
dummyheaddummyhead
GENERAL INFORMATION
PAIR AIR SUCTION HOSE
PAIR AIR SUPPLY HOSE
Viewed from the rear side:
RADIATOR SIPHON HOSE
FUEL PUMP 3P (BLACK) CONNECTOR
SPARK PLUG WIRE
PAIR AIR SUCTION HOSE
PAIR AIR SUPPLY HOSE
DLC
PAIR CONTROL SOLENOID VALVE
FAN MOTOR 2P (BLACK) CONNECTOR
WATER HOSE BAND
Front
WATER HOSE BAND
Front
WATER HOSE BAND
O2 SENSOR 1P (BLACK) CONNECTOR
ECT SENSOR 3P CONNECTOR
SENSOR UNIT 5P CONNECTOR
Left
90°± 30°
55°± 30°
20°± 30°
1-23
dummyheaddummyhead
GENERAL INFORMATION
FUEL TANK BREATHER HOSE
BATTERY CASE DRAIN HOSE
SIDESTAND SWITCH WIRE
CONNECTORS:– ALTERNATOR 3P– REAR BRAKE LIGHT SWITCH 3P (BLACK)– SIDESTAND SWITCH 3P (GREEN)– CKP SENSOR/NEUTRAL SWITCH 3P (BLACK)
ECT SENSOR 3P CONNECTOR
VS SENSOR 3P (BLUE) CONNECTOR
WIRE CLAMP
STARTER MOTOR CABLE
BATTERY NEGATIVE (-) CABLE
NEUTRAL SWITCH
CRANKCASE BREATHER HOSE
SIDESTAND SWITCH WIRE
BATTERY CASE DRAIN HOSE
SIDESTAND SWITCH WIRE
BATTERY NEGATIVE (-) CABLE
NEUTRAL SWITCH WIRE
DRIVE SPROCKET COVER
LEFT CRANKCASE COVER
Viewed from the upper side:
Viewed from the lower side:
ALTERNATOR WIRE
FUEL TANK BREATHER HOSE
RESERVE TANK OVERFLOW HOSE
1-24
dummyheaddummyhead
GENERAL INFORMATION
BATTERY NEGATIVE (-) CABLE
Viewed from the front side:
BATTERY POSITIVE (+) CABLE
STARTER RELAY SWITCH 4P (RED) CONNECTOR
FAN CONTROL RELAY
FUEL PUMP RELAY
STARTER MOTOR CABLE
WIRE BANDS
STARTER MOTOR CABLE
SUB-FRAME
MAIN WIRE HARNESS
REAR BRAKE LIGHT SWITCH WIRE
REAR BRAKE HOSE
1-25
dummyheaddummyhead
GENERAL INFORMATION
BRAKE/TAILLIGHT 6P (BLACK) CONNECTOR
LEFT REAR TURN SIGNAL 2P (ORANGE) CONNECTOR
RIGHT REAR TURN SIGNAL 2P (LIGHT BLUE) CONNECTOR
MAIN WIRE HARNESS
1-26
dummyheaddummyhead
GENERAL INFORMATION
EMISSION CONTROL SYSTEMSSOURCE OF EMISSIONSThe combustion process produces carbon monoxide (CO), oxides of nitrogen (NOX) and hydrocarbons (HC). Control of oxides ofnitrogen and hydrocarbons is very important because, under certain conditions, they react to form photochemical smog whensubject to sunlight. Carbon monoxide does not react in the same way, but it is toxic.
Honda Motor Co., Ltd. utilizes various systems (page 1-28) to reduce carbon monoxide, oxides of nitrogen and hydrocarbons.
CRANKCASE EMISSION CONTROL SYSTEMThe engine is equipped with a closed crankcase system to prevent discharging crankcase emissions into the atmosphere. Blow-bygas is returned to the combustion chamber through the air cleaner housing and throttle body.
BLOW-BY GAS
FRESH AIR
THROTTLE BODY
AIR CLEANER HOUSING
CRANKCASE BREATHER HOSE
1-27
dummyheaddummyhead
GENERAL INFORMATION
EXHAUST EMISSION CONTROL SYSTEMThe exhaust emission control system is composed of a pulse secondary air supply system, three-way catalytic converter and PGM-FI system.
SECONDARY AIR SUPPLY SYSTEMThe pulse secondary air supply system introduces filtered air into the exhaust gases in the exhaust port. Fresh air is drawn into theexhaust port by the function of the PAIR control valve.This charge of fresh air promotes burning of the unburned exhaust gases and changes a considerable amount of hydrocarbons andcarbon monoxide into relatively harmless carbon dioxide and water vapor.The reed valve prevents reverse air flow through the system. The PAIR control valve is operated by the solenoid valve. Thesolenoid valve is controlled by the PGM-FI unit, and the fresh air passage is opened/closed according to running condition (ECT/IAT/TP/MAP sensor and engine revolution).No adjustments to the secondary air supply system should be made, although periodic inspection of the components isrecommended.
THREE-WAY CATALYTIC CONVERTERThis motorcycle is equipped with a three-way catalytic converter.
The three-way catalytic converter is in the exhaust system. Through chemical reactions, it converts HC, CO and NOX in theengine’s exhaust to carbon dioxide (CO2), nitrogen (N2), and water vapor.
No adjustment to these systems should be made although periodic inspection of the components is recommended.
PAIR CHECK VALVE
EXHAUST PORT
FRESH AIR
EXHAUST GAS
PAIR CONTROL SOLENOID VALVE AIR CLEANER HOUSING
THROTTLE BODY
1-28
dummyheaddummyhead
GENERAL INFORMATION
NOISE EMISSION CONTROL SYSTEMTAMPERING WITH THE NOISE CONTROL SYSTEM IS PROHIBITED: Local law may prohibit the following acts or the causingthere of: (1) The removal or rendering inoperative by any person, other than for purposes of maintenance, repair or replacement, ofany device or element of design incorporated into any vehicle for the purpose of noise control prior to its sale or delivery to theultimate customer or while it is in use; (2) the use of the vehicle after such device or element of design has been removed orrendered inoperative by any person.
AMONG THOSE ACTS PRESUMED TO CONSTITUTE TAMPERING ARE THE ACTS LISTED BELOW:
1. Removal of, or puncturing of the muffler, baffles, header pipes or any other component which conducts exhaust gases.2. Removal of, or puncturing of any part of the intake system.3. Lack of proper maintenance.4. Replacing any moving parts of the vehicle, or parts of the exhaust or intake system, with parts other than those specified by the
manufacturer.
1-29
dummyheaddummyhead
MEMO
dummytext
2. FRAME/BODY PANELS/EXHAUST SYSTEM
2
SERVICE INFORMATION·····························2-2
TROUBLESHOOTING···································2-2
SEAT······························································2-3
SIDE COVER·················································2-3
RESERVE TANK COVER ·····························2-4
FUEL TANK SHROUD ··································2-4
SKID PLATE··················································2-5
HEADLIGHT COWL ······································2-5
FRONT FENDER···········································2-5
FRAME GUARD ············································2-6
DRIVE SPROCKET COVER ························· 2-6
DRIVE CHAIN COVER (U TYPE ONLY) ············································ 2-6
TOOL BOX ···················································· 2-7
REAR FENDER············································· 2-7
REAR UPPER FENDER ······························· 2-8
TAIL COVER/LIGHT UNIT···························· 2-8
REAR LOWER FENDER ······························ 2-9
EXHAUST PIPE/MUFFLER ························ 2-11
SUB-FRAME ··············································· 2-12
SIDESTAND ················································ 2-14
2-1
dummyheaddummyhead
FRAME/BODY PANELS/EXHAUST SYSTEM
FRAME/BODY PANELS/EXHAUST SYSTEMSERVICE INFORMATIONGENERAL • This section covers removal and installation of the body panels, sub-frame and exhaust system. • Always replace the gaskets when removing the exhaust system. • Always inspect the exhaust system for leaks after installation.
TROUBLESHOOTINGExcessive exhaust noise • Broken exhaust system • Exhaust gas leak
Poor performance • Deformed exhaust system • Exhaust gas leak • Clogged muffler
2-2
dummyheaddummyhead
FRAME/BODY PANELS/EXHAUST SYSTEM
SEATREMOVAL/INSTALLATIONRemove the hook bolts [1] and collars [2].
Remove the seat [3] by pulling it rearward and releasingthe hooks.
Installation is in the reverse order of removal.
SIDE COVERREMOVAL/INSTALLATION
Right side: Remove the socket bolt [1] and collar [2].
Remove the socket bolt [1].
Release the boss [3] from the frame grommet, thenremove the side cover [4] by pulling it rearward.
Installation is in the reverse order of removal.
• Align the cover grooves with the tabs of the fuel tankshroud.
DISASSEMBLY/ASSEMBLY (LEFT SIDE ONLY)Remove the screws [1] and separate the side lowercover [2] from the left side cover [3] by releasing itsslots [4] and holes [5] from the hooks and bosses of theside cover.
Assembly is in the reverse order of disassembly.
TORQUE:Hook bolt: 21 N·m (2.1 kgf·m, 15 lbf·ft)
[3] [1]/[2]
Left side:
[3]
[1][4]
Align
[2] (Right side only)
TORQUE:Left side cover assembly screw:
0.9 N·m (0.1 kgf·m, 0.7 lbf·ft)
[1]
[3] [4]
[5]
[2]
2-3
dummyheaddummyhead
FRAME/BODY PANELS/EXHAUST SYSTEM
RESERVE TANK COVERREMOVAL/INSTALLATIONRemove the trim clips [1], socket bolt [2] and reservetank cover [3].
Installation is in the reverse order of removal.
• Align the cover boss [4] with the hole [5] of the stay.
FUEL TANK SHROUDREMOVAL/INSTALLATION
Right side only: Remove the reserve tank cover (page 2-4).
Remove the side cover (page 2-3).
Remove the socket bolt A [1], socket bolts B [2] and fueltank shroud [3].
Installation is in the reverse order of removal.
DISASSEMBLY/ASSEMBLYRight side: Remove the four screws [1] and separate the grille [2]
and front shroud [3] from the rear shroud [4] byreleasing its tabs [5] and boss [6] from the slots andhole of the rear shroud.
Remove the two screws [1] and separate the frontshroud [3] from the rear shroud [4] by releasing its tabs[5] and boss [6] from the slots and hole of the rearshroud.
Assembly is in the reverse order of disassembly.
[2]
[3]
[1]
[5]
[4]
[2]
[3]
[1]
Left side:
TORQUE:Fuel tank shroud assembly screw:
0.9 N·m (0.1 kgf·m, 0.7 lbf·ft)[3]
[5]
[2] (Right side only)
[4]
[1] [6]
[1] (Right side only)
2-4
dummyheaddummyhead
FRAME/BODY PANELS/EXHAUST SYSTEM
SKID PLATEREMOVAL/INSTALLATIONRemove the two bolts [1] and skid plate [2].
Installation is in the reverse order of removal.
• Align the rear side of the skid plate with the frameslot [3].
HEADLIGHT COWLREMOVAL/INSTALLATIONRemove the four bolt/washers [1] and headlight cowl[2].Disconnect the headlight 3P (Black) connector [3] andposition light 2P (Black) connector [4].
Installation is in the reverse order of removal.
FRONT FENDERREMOVAL/INSTALLATIONRemove the four bolt/washers [1], front fender [2] andcollars [3]
Installation is in the reverse order of removal.
[2][3]
[1]
TORQUE:Headlight cowl mounting bolt:
8.5 N·m (0.9 kgf·m, 6.3 lbf·ft)
[2][3]
[1]
[4]
[2]
[3]
[1]
2-5
dummyheaddummyhead
FRAME/BODY PANELS/EXHAUST SYSTEM
FRAME GUARDREMOVAL/INSTALLATIONRemove the socket bolts [1] and frame guard [2].
Installation is in the reverse order of removal.
DRIVE SPROCKET COVERREMOVAL/INSTALLATIONRemove the bolts [1] and drive sprocket cover [2].
Installation is in the reverse order of removal.
DRIVE CHAIN COVER (U TYPE ONLY)REMOVAL/INSTALLATIONRemove the socket bolts [1] and drive chain cover [2].
Installation is in the reverse order of removal.
[2]
[1]
[2]
[1]
[2]
[1]
2-6
dummyheaddummyhead
FRAME/BODY PANELS/EXHAUST SYSTEM
TOOL BOXREMOVAL/INSTALLATIONRemove the following:
– Seat (page 2-3)– Left side cover (page 2-3)
Remove the two mounting bolts [1] and tool box [2].
Installation is in the reverse order of removal.
DISASSEMBLY/ASSEMBLYDisassemble and assemble the tool box as following illustration.
REAR FENDERREMOVAL/INSTALLATIONRemove the bolts [1] and rear fender [2].
Installation is in the reverse order of removal.
[2][1]
TOOL BOX
SPECIAL WASHER
HINGE
TOOL BOX COVER
LOCK UNIT
LOCK SPRING
[2]
[1]
2-7
dummyheaddummyhead
FRAME/BODY PANELS/EXHAUST SYSTEM
DISASSEMBLY/ASSEMBLY (U TYPE ONLY)Remove the nuts [1], bolts [2], collars [3], license holderplate [4] and license plate stay [5].
Remove the stopper rubber [6].
Remove the nuts [7] and rear side reflectors [8].
Assembly is in the reverse order of disassembly.
REAR UPPER FENDERREMOVAL/INSTALLATIONRemove the seat (page 2-3).
Remove the hook bolts [1] and collars [2].
Slightly spread the side covers [3] and release thebosses [4] and tabs [5].Remove the rear upper fender [6].
Installation is in the reverse order of removal.
TAIL COVER/LIGHT UNITREMOVAL/INSTALLATIONRemove the following:
– Rear upper fender (page 2-8)– Rear fender (page 2-7)
Disconnect the brake/taillight 6P (Black) connector [1].
Remove the bolts A [2], bolts B [3] and tail cover/lightunit [4].
Installation is in the reverse order of removal.
TORQUE:Rear side reflector mounting nut:
1.5 N·m (0.2 kgf·m, 1.1 lbf·ft)
[1]/[3]
[2] [5]
[4]
[7]
[8]
[6]
TORQUE:Hook bolt: 21 N·m (2.1 kgf·m, 15 lbf·ft)
[2]
[3]
[1]
[5]
[4]
[6]
[2]
[3]
[1]
[4]
2-8
dummyheaddummyhead
FRAME/BODY PANELS/EXHAUST SYSTEM
DISASSEMBLY/ASSEMBLYRemove the following:
– Rear fender (page 2-7)– Rear turn signal units (page 20-4)
Disassemble and assemble the tail cover/light unit as following illustration.
REAR LOWER FENDERREMOVAL/INSTALLATIONRemove the following:
– Seat (page 2-3)– Side covers (page 2-3)– Tail cover/light unit (page 2-8)
Release the wire bands [1].
BRAKE/TAILLIGHT MOUNTING SCREWS
4.5 N·m (0.5 kgf·m, 3.3 lbf·ft)
COLLARS
REAR TURN SIGNAL UNIT STAY
BRAKE/TAILLIGHT UNIT
SCREW
LEFT TAIL COVER
REAR REFLECTOR
SOCKET BOLTS
RIGHT TAIL COVER
REFLECTOR MOUNTING NUT1.5 N·m (0.2 kgf·m, 1.1 lbf·ft)
[1]
2-9
dummyheaddummyhead
FRAME/BODY PANELS/EXHAUST SYSTEM
Remove the rear lower fender mounting bolt [1].
Remove the bolts [1], helmet holder [2] and rear lowerfender [3].
Use a drill or an equivalent tool when removing thehelmet holder mounting bolts.
Installation is in the reverse order of removal.
• Replace the helmet holder mounting bolts with newones.
[1]
[1]
[2]
[3]
2-10
dummyheaddummyhead
FRAME/BODY PANELS/EXHAUST SYSTEM
EXHAUST PIPE/MUFFLERREMOVAL/INSTALLATIONRemove the following:
– Seat (page 2-3)– Right side cover (page 2-3)
Remove the exhaust pipe/muffler as followingillustration.
Installation is in the reverse order of removal.
STUD BOLT REPLACEMENTRemove the exhaust pipe (page 2-11).
Thread two nuts onto the stud bolt and tighten themtogether, and use a wrench on them to turn the stud boltout.
Install and tighten new stud bolts to the specifiedtorque.
After installation, check that the length from the bolthead to the cylinder head surface is within specification.
SOCKET BOLTS12 N·m (1.2 kgf·m, 9 lbf·ft)
18 N·m (1.8 kgf·m, 13 lbf·ft)
22.5 N·m (2.3 kgf·m, 17 lbf·ft)
32 N·m (3.3 kgf·m, 24 lbf·ft)
MUFFLER
MUFFLER PROTECTOR
SOCKET BOLTS
BOLT
BAND BOLT
MUFFLER FRONT MOUNTING BOLT NUT
GASKET
EXHAUST PIPE
JOINT NUTS
EXHAUST PIPE PROTECTOR
GASKET
DAMPER RUBBER
TORQUE: 9.0 N·m (0.9 kgf·m, 6.6 lbf·ft)
22.0 ± 0.5 mm (0.87 ± 0.02 in)
2-11
dummyheaddummyhead
FRAME/BODY PANELS/EXHAUST SYSTEM
SUB-FRAMEREMOVAL/INSTALLATIONRemove the following:
– Seat (page 2-3)– Side covers (page 2-3)– Muffler (page 2-11)– Fuel tank (page 7-8)– Battery (page 19-4)
Remove the bolt [1] and reservoir [2].
Disconnect the PAIR air suction hose [3] and crankcasebreather hose [4] from the air cleaner housing.
Remove the wire bands [1].
Remove the following from the air cleaner housing.
– Starter relay switch [2]– Fuse box [3]– Relay box [4]– Wire clips [5]
Open the harness band [1] and release the wires.
Disconnect the battery case drain hose [2].
Release the wire bands [1].
Disconnect the brake/taillight 6P (Black) connector [2].
[2]
[3][1]
[4]
[1]
[2]
[4][5]
[5]
[3]
[2][1]
[1]
[2]
2-12
dummyheaddummyhead
FRAME/BODY PANELS/EXHAUST SYSTEM
Loosen the air cleaner connecting hose band screw [1].
Remove the sub-frame lower mounting bolts [1].
Remove the sub-frame upper mounting nuts [1] andbolts [2].
Pull the sub-frame assembly rearward, then disconnectthe air cleaner connecting hose from the throttle body.Remove the sub-frame.
Install the sub-frame in position, connect the air cleanerconnecting hose to the throttle body.Tighten the band screw to the specified torque.
Loosely install all the mounting fasteners.Tighten the upper mounting nut first, then the lowerbolts to the specified torque.
Install the removed parts in the reverse order ofremoval.
[1]
[1]
TORQUE: 1.5 N·m (0.2 kgf·m, 1.1 lbf·ft)
TORQUE:Sub-frame upper mounting nut:
27 N·m (2.8 kgf·m, 20 lbf·ft)Sub-frame lower mounting bolt:
27 N·m (2.8 kgf·m, 20 lbf·ft)
TORQUE:Rear master cylinder reservoir mounting bolt:
10 N·m (1.0 kgf·m, 7 lbf·ft)
[1][2]
2-13
dummyheaddummyhead
FRAME/BODY PANELS/EXHAUST SYSTEM
SIDESTANDREMOVAL/INSTALLATIONRemove the sidestand switch (page 20-14).
Remove the return spring [1] and sub spring [2].
Remove the pivot lock nut [3], pivot bolt [4] andsidestand [5].
Apply grease to the sidestand pivot bolt sliding surface.Install the sidestand and pivot bolt, then tighten it to thespecified torque.
Turn the pivot bolt counterclockwise about 45° – 90°.
Install the pivot lock nut and tighten it to the specifiedtorque while holding the pivot bolt.
Install the return spring and sub spring as shown.
Install the sidestand switch (page 20-14).
TORQUE: 10 N·m (1.0 kgf·m, 7 lbf·ft)
TORQUE: 30 N·m (3.1 kgf·m, 22 lbf·ft)
[1]/[2]
[3][4]
[5]
[1]
[2]
2-14
dummytext
3. MAINTENANCE
3
SERVICE INFORMATION·····························3-2
MAINTENANCE SCHEDULE························3-2
FUEL LINE·····················································3-3
THROTTLE OPERATION······························3-3
AIR CLEANER···············································3-4
CRANKCASE BREATHER ···························3-4
SPARK PLUG················································3-5
VALVE CLEARANCE····································3-6
ENGINE OIL ··················································3-9
ENGINE OIL FILTER···································3-10
ENGINE IDLE SPEED·································3-10
RADIATOR COOLANT ·······························3-11
COOLING SYSTEM·····································3-11
SECONDARY AIR SUPPLY SYSTEM········3-11
DRIVE CHAIN ············································· 3-12
DRIVE CHAIN SLIDER ······························· 3-14
BRAKE FLUID ············································ 3-15
BRAKE PADS WEAR ································· 3-16
BRAKE SYSTEM ········································ 3-17
BRAKE LIGHT SWITCH ····························· 3-17
HEADLIGHT AIM ········································ 3-18
CLUTCH SYSTEM ······································ 3-18
SIDESTAND ················································ 3-19
SUSPENSION ············································· 3-19
NUTS, BOLTS, FASTENERS ····················· 3-19
WHEELS/TIRES·········································· 3-20
STEERING HEAD BEARINGS ··················· 3-20
3-1
dummyheaddummyhead
MAINTENANCE
MAINTENANCESERVICE INFORMATIONGENERAL • Place the motorcycle on level surface before starting any work. • Gasoline is extremely flammable and is explosive under certain conditions. • Work in a well ventilated area. Smoking or allowing flames or sparks in the work area or where the gasoline is stored can cause
a fire or explosion. • The exhaust contains poisonous carbon monoxide gas that may cause loss of consciousness and may lead to death. Run the
engine in an open area or with an exhaust evacuation system in an enclosed area.
MAINTENANCE SCHEDULEPerform the Pre-ride inspection in the Owner's Manual at each scheduled maintenance period.
I: Inspect and Clean, Adjust, Lubricate or Replace if necessary. C: Clean. R: Replace. A: Adjust. L: Lubricate.
The following items require some mechanical knowledge. Certain items (particularly those marked * and **) may require moretechnical information and tools. Consult a dealer.
* Should be serviced by a dealer, unless the owner has proper tools and service data and is mechanically qualified.
** In the interest of safety, we recommend these items be serviced only by a dealer.
Honda recommends that a dealer should road test your motorcycle after each periodic maintenance is carried out.
NOTES:
1. At higher odometer readings, repeat at the frequency interval established here.2. Service more frequently when riding in unusually wet or dusty areas.3. Service more frequently when riding in rain or at full throttle.4. Service more frequently when riding OFF-ROAD.5. Replacement requires mechanical skill.
NOTEFREQUENCY (NOTE 1)
ANNUAL CHECK
REGULAR REPLACE
REFER TO PAGEx 1,000 km 1 12 24 36 48
ITEMS x 1,000 mi 0.6 8 16 24 32* FUEL LINE I I I I I 3-3* THROTTLE OPERATION I I I I I 3-3* AIR CLEANER NOTE 2 R R 3-4
CRANKCASE BREATHER NOTE 3 C C C C C 3-4* SPARK PLUG I R 3-5* VALVE CLEARANCE I I I 3-6
ENGINE OIL R R R R R R 3-9ENGINE OIL FILTER R R R R R R 3-10
* ENGINE IDLE SPEED I I I I I I 3-10RADIATOR COOLANT NOTE 5 I I I I I 3 YEARS 3-11
* COOLING SYSTEM I I I I I 3-11* SECONDARY AIR SUPPLY SYSTEM I I I I I 3-11
DRIVE CHAIN NOTE 4 EVERY 1,000 km (600 mi) I, L
3-12
DRIVE CHAIN SLIDER NOTE 4 I I I I 3-14BRAKE FLUID NOTE 5 I I I I I 2 YEARS 3-15BRAKE PADS WEAR I I I I I 3-16BRAKE SYSTEM I I I I I I 3-17BRAKE LIGHT SWITCH I I I I I 3-17HEADLIGHT AIM I I I I I 3-18CLUTCH SYSTEM I I I I I I 3-18SIDESTAND I I I I I 3-19
* SUSPENSION I I I I I 3-19* NUTS, BOLTS, FASTENERS NOTE 4 I I I I I I 3-19
** WHEELS/TIRES NOTE 4 I EVERY 6,000 km (4,000 mi) I I3-20
** STEERING HEAD BEARINGS I I I I I I 3-20
3-2
dummyheaddummyhead
MAINTENANCE
FUEL LINEINSPECTIONRemove the right fuel tank shroud (page 2-4).
Check the quick connect fitting [1] for looseness.
Check the fuel feed hose [2] for deterioration, damageor leakage.
Check the quick connect fitting for dirt, and clean ifnecessary.
Replace the fuel pump packing if necessary (page 7-9).
THROTTLE OPERATIONCheck for any deterioration or damage to the throttlecable.Check the throttle grip for smooth operation.Check that the throttle opens and automatically closesin all steering positions.
If the throttle grip does not return properly, overhaul andlubricate the throttle grip housing.
If the throttle grip still do not return properly, replace thethrottle cable.
With the engine idling, turn the handlebar all the way tothe right and left to ensure that the idle speed does notchange.If idle speed increases, check the throttle grip freeplayand throttle cable connection.
Measure the throttle grip freeplay at the throttle gripflange.
Throttle grip freeplay can be adjusted at either end ofthe throttle cable.
Minor adjustment is made with the upper adjuster [1] atthrottle housing.
Loosen the lock nut [2] and turn the adjuster.
Tighten the lock nut securely while holding the adjuster.
Recheck the throttle operation.
[2]
[1]
FREEPLAY: 2 – 6 mm (0.08 – 0.24 in)
2 – 6 mm (0.08 – 0.24 in)
[1]
[2]
3-3
dummyheaddummyhead
MAINTENANCE
Major adjustment is made with the lower adjuster [1] atthe throttle body.
Loosen the lock nut [2] and turn the adjuster.Tighten the lock nut to the specified torque whileholding the adjuster.
Recheck the throttle operation.
AIR CLEANERREMOVAL/INSTALLATION
• The viscous paper element cannot be cleanedbecause the element contains a dust adhesive.
• If the motorcycle is used in unusually wet or dustyareas, more frequent inspections are required.
Remove the right side cover (page 2-3).
Remove the screws [1] and air cleaner cover [2].
Remove the air cleaner element [3] by releasing itsgrooves from the housing.
Inspect the air cleaner element in accordance with themaintenance schedule (page 3-2) or any time it isexcessively dirt or damaged.
Install the air cleaner element in the reverse order ofremoval.
• After installing air cleaner element, make sure the aircleaner element grooves are secure.
• Check that the condition of the packings, replacethem if necessary.
CRANKCASE BREATHERService more
frequently whenridden in rain, at fullthrottle, or after the
motorcycle iswashed or
overturned.
Check the crankcase breather hose [1] for deterioration,damage or loose connection. Make sure that the hosesare not kinked, pinched or cracked.
Replace the crankcase breather hose if necessary.
TORQUE:3.0 N·m (0.3 kgf·m, 2.2 lbf·ft)
[1]
[2]
TORQUE:Air cleaner cover screw:
1.2 N·m (0.1 kgf·m, 0.9 lbf·ft)
[2]
[1]
[3]
[1]
3-4
dummyheaddummyhead
MAINTENANCE
Service if the
deposits level canbe seen in the air
cleaner housingdrain plug.
Check the air cleaner housing drain plug [1].
If necessary, remove the drain plug from the air cleanerand drain the deposits into a suitable container.
Reinstall the drain plug securely.
SPARK PLUGREMOVAL/INSTALLATIONDisconnect the spark plug cap [1].
Clean around thespark plug base
with compressed airbefore removing the
spark plug, and besure that no debrisis allowed to enter
into the combustionchamber.
Remove the spark plug [1] using a spark plug wrench[2].
Inspect or replace the spark plug as described in themaintenance schedule (page 3-2).
Install and hand tighten the spark plug to the cylinderhead, then tighten the spark plug to the specified torqueusing a spark plug wrench.
Connect the spark plug cap securely.
INSPECTIONCheck the following and replace if necessary(recommended spark plug: page 3-6).
• Insulator [1] for damage • Center electrode [2] and side electrode [3] for wear • Burning condition, coloration
If the electrodes are contaminated with accumulatedobjects or dirt, replace the spark plug.
[1]
[1]
TORQUE:16 N·m (1.6 kgf·m, 12 lbf·ft)
[1]
[2]
This motorcycle'sspark plug is
equipped with aniridium center
electrode. Replacethe spark plug if the
electrodes arecontaminated.
[1]
[2] [3]
3-5
dummyheaddummyhead
MAINTENANCE
Always use
specified sparkplugs on thismotorcycle.
Replace the plug if the center electrode [1] is roundedas shown in the illustration.
To preventdamaging theiridium center
electrode, use awire type feeler
gauge to check thespark plug gap.
Check the spark plug gap between the center and sideelectrodes with a wire type feeler gauge [1].
Make sure that the Φ 1.0 mm (0.039 in) plug gaugedoes not insert between the gap.
If the gauge can be inserted into the gap, replace theplug with a new one.
VALVE CLEARANCEINSPECTION
• Inspect and adjust the valve clearance while theengine is cold (below 35°C/95°F).
• After the valve clearance inspection, check theengine idle speed (page 3-10).
• Inspection and adjustment can be done with theengine installed in the frame.
Remove the cylinder head cover (page 10-4).
Remove the timing hole cap [1] and crankshaft hole cap[2].
Rotate the crankshaft counterclockwise and align the"T" mark [1] on the flywheel with the index notch [2] onthe left crankcase cover.
SPECIFIED SPARK PLUG:NGK: SIMR8A9
[1]
Do not adjust thespark plug gap. Ifthe gap is out of
specification,replace with a new
one.
[1]
TOOL:Timing cap wrench 07709-0010001
[1]
[2]
[2]
[1]
[2]
3-6
dummyheaddummyhead
MAINTENANCE
Make sure that the outside index lines ("IN" [1] and "EX"[2] marks) on the cam sprockets are flush with thecylinder head top surface and facing outward as shown.
If the "IN" and "EX" marks are facing inward, turn thecrankshaft counterclockwise one full turn (360°) andrealign the "T" mark with the index notch.
Check the valve clearance by inserting a feeler gauge[1] between the rocker arm and shim.
ADJUSTMENT
• The valve clearances can be adjusted withoutremoving the camshafts.
• The intake and exhaust valve clearance serviceprocedures are the same.
Remove the bolt, sealing washer and rocker arm shaft(page 10-11).
Slide the rocker arm [1] and remove the shims [2].
• Do not allow the shims to fall into the crankcase. • Mark all shims to ensure correct reassembly in their
original locations. • The shims can be easily removed with a tweezers or
magnet.
[1]
[2]
VALVE CLEARANCE:IN: 0.16 ± 0.03 mm (0.006 ± 0.001 in)EX: 0.27 ± 0.03 mm (0.011 ± 0.001 in)
[1]
[1]
[2]
3-7
dummyheaddummyhead
MAINTENANCE
Sixty-nine different
thickness shims areavailable from the
thinnest 1.200 mmthickness shim tothe thickest 2.900
mm thickness shimin increments of
0.025 mm.
Measure the shim [1] thickness and record it.
Calculate the new shim thickness using the equationbelow.
A = (B – C) + D
A: New shim thicknessB: Recorded valve clearanceC: Specified valve clearanceD: Old shim thickness
• Make sure of the correct shim thickness bymeasuring the shim by micrometer.
• Inspect the valve seat if the calculated dimension isover 2.900 mm.
Install the shims intheir original
locations
Install the newly selected shim [1] on the valve springretainer.
Install the rocker arm shaft while aligning the hole of therocker arm [2] and cylinder head (page 10-11).
Rotate the camshafts by turning the crankshaftcounterclockwise several times.Recheck the valve clearance.
Install the cylinder head cover (page 10-5).
Apply engine oil to new O-rings [1] and install them toeach hole cap.
Apply engine oil to timing hole cap [2] and crankshafthole cap [3] threads.
Install and tighten the timing hole cap and crankshafthole cap to the specified torque.
[1]
1.80 mm 1.825 mm 1.85 mm 1.875 mm
[2]
[1]
TOOL:Timing cap wrench 07709-0010001
TORQUE:Timing hole cap: 6.0 N·m (0.6 kgf·m, 4.4 lbf·ft)Crankshaft hole cap: 8.0 N·m (0.8 kgf·m, 5.9 lbf·ft)
[1]
[3] [2]
3-8
dummyheaddummyhead
MAINTENANCE
ENGINE OILOIL LEVEL INSPECTIONHold the motorcycle in an upright position.
Start the engine and let it idle for 3 – 5 minutes.Stop the engine and wait 2 – 3 minutes.
Check the oil level through the inspection window.
If the level is below the lower level line [1], remove theoil filler cap [2] and fill the crankcase with therecommended oil up to the upper level line [3].
Check that the O-ring [4] is in good condition, replace itif necessary.
Apply engine oil to the O-ring.
Install the oil filler cap.
ENGINE OIL CHANGEWarm up the engine.
Stop the engine and remove the oil filler cap [1].
Place an oil pan under the engine to catch the engineoil, then remove the engine oil drain bolt [1]/sealingwasher [2].
Drain the engine oil completely.
Install a new sealing washer onto the drain bolt.
Install and tighten the drain bolt to the specified torque.
Fill the engine with the recommended engine oil (page3-9).
Install the oil filler cap.
Check the oil level (page 3-9).
Make sure there are no oil leaks.
RECOMMENDED ENGINE OIL:Honda "4-stroke motorcycle oil" or an equivalentAPI classification: SG or higher (except oils labeled as energy conserving on the circular API service label)Viscosity: SAE 10W-30JASO T 903 standard: MA
[1]
[4]
[2]
[3]
[1]
TORQUE:24 N·m (2.4 kgf·m, 18 lbf·ft)
ENGINE OIL CAPACITY:1.4 liters (1.5 US qt, 1.2 Imp qt) at draining1.5 liters (1.6 US qt, 1.3 Imp qt) at oil filter change1.8 liters (1.9 US qt, 1.6 Imp qt) at disassembly
[1]
[2]
3-9
dummyheaddummyhead
MAINTENANCE
ENGINE OIL FILTERREPLACEMENTDrain the engine oil (page 3-9).
Remove the following:
– Bolts [1]– Oil filter cover [2]– Gasket [3]– Spring [4]
Remove the oil filter [1].
Install a new oil filter with the "OUT-SIDE" mark [2]facing out.
Installing the oil filter backwards will result in severeengine damage.
Install the oil filter spring [3] into the oil filter cover [4].Install a new gasket [5] and oil filter cover.
Install the cover bolts and tighten them.
Fill the engine with the recommended engine oil (page3-9).
Make sure there are no oil leaks.
ENGINE IDLE SPEED
• Inspect the idle speed after all other enginemaintenance items have been performed and arewithin specifications.
• Before checking the idle speed, inspect the followingitems.– No MIL blinking– Spark plug condition (page 3-5)– Secondary air supply system condition (page 3-
11)– Crankcase breather system condition (page 3-4)– Air cleaner element condition (page 3-4)
• The engine must be warm for accurate idle speedinspection.
• This system eliminates the need for manual idlespeed adjustment compared to previous designs.
Start the engine and let it idle.Check the idle speed.
If the idle speed is out of the specification, check thefollowing:
– Intake air leak or engine top-end problem (page 10-2)
– Throttle operation and freeplay (page 3-3)– IACV operation (page 7-16)
[2]/[3] [4]
[1]
[1]
[2] [5][4]
[3]
IDLE SPEED: 1,450 ± 100 min-1 (rpm)
3-10
dummyheaddummyhead
MAINTENANCE
RADIATOR COOLANTCheck the coolant level of the reserve tank with theengine running at normal operating temperature.
The level should be between the "UPPER" [1] and"LOWER" [2] level lines with the motorcycle in anupright position.
If the level is low, remove the reserve tank cap [3] andfill the tank to the "UPPER" level line with a 1:1 mixtureof distilled water and antifreeze.
Check to see if there are any coolant leaks when thecoolant level decreases very rapidly.
If the reserve tank becomes completely empty, there isa possibility of air getting into the cooling system.Be sure to remove any air from the cooling system(page 9-5).
COOLING SYSTEMCheck the radiator air passages for clogging ordamage.Straighten bent fins, and remove insects, mud or otherobstructions with compressed air or low water pressure.Replace the radiator if the air flow is restricted overmore than 20% of the radiating surface.
Inspect the water hoses for cracks or deterioration, andreplace them if necessary.Check the tightness of all water hose band screws(page 9-7).
SECONDARY AIR SUPPLY SYSTEM
• This model is equipped with a built-in secondary airsupply system. The pulse secondary air supplysystem is located on the cylinder head cover [1].
• The secondary air supply system introduces filteredair into exhaust gases in the exhaust port [2].The secondary air is drawn into the exhaust portwhenever there is negative pressure pulse in theexhaust system. This charged secondary airpromotes burning of the unburned exhaust gasesand changes a considerable amount ofhydrocarbons and carbon monoxide into relativelyharmless carbon dioxide and water.
RECOMMENDED ANTIFREEZE:High quality ethylene glycol antifreeze containing silicate-free corrosion inhibitors
[1]
[3]
[2]
[1]
[2]
3-11
dummyheaddummyhead
MAINTENANCE
Remove the right fuel tank shroud (page 2-4).
Check the PAIR air supply hose [1] between the PAIRcontrol solenoid valve [2] and cylinder head cover fordeterioration, damage or loose connections. Make surethat the hoses are not cracked.
Check the air suction hose [3] between the air cleanerand PAIR control solenoid valve for deterioration,damage or loose connections.Make sure that the hoses are not kinked, pinched orcracked.
DRIVE CHAINDRIVE CHAIN SLACK INSPECTION
Never inspect andadjust the drivechain while the
engine is running.
Turn the ignition switch OFF, support the motorcycle onits sidestand and shift the transmission into neutral.
Check the slack in the drive chain lower run midwaybetween the sprockets.
Excessive chain slack, 50 mm (2.0 in) or more, maydamage the frame.
ADJUSTMENTLoosen the rear axle nut [1].Loosen the lock nuts [2] and turn the adjusters [3] untilthe correct drive chain slack is obtained.
If the hoses showany signs of heatdamage, inspectthe PAIR check
valve in the cylinderhead cover for
damage (page 7-18).
[2][1]
[3]
DRIVE CHAIN SLACK: 25 – 35 mm (1.0 – 1.4 in)25 – 35 mm (1.0 – 1.4 in)
[2][1]
[3]
3-12
dummyheaddummyhead
MAINTENANCE
Make sure the same index lines [1] on both adjustingplates [2] are aligned with punch mark [3] in theswingarm.Tighten the axle nut to the specified torque.
Hold the drive chain adjusters [4] and tighten the locknuts [5] to the specified torque.
Recheck the drive chain slack and free wheel rotation.
Check the drive chain wear indicator label attached onthe left swingarm.
If the drive chain adjuster cut-out [1] reaches red zone[2] of the indicator label, replace the drive chain with anew one.
CLEANING AND LUBRICATIONClean the drive chain [1] with a chain cleaner designedspecifically for O-ring chains or a neutral detergent. Usea soft brush if the drive chain is dirty.
Do not use a steam cleaner, high pressure cleaner, wirebrush, volatile solvent such as gasoline and benzene,abrasive cleaner or a chain cleaner NOT designedspecifically for O-ring chains to clean the drive chain.
Inspect the drive chain for possible damage or wear.
Replace any drive chain that has damaged rollers,loose fitting links, or otherwise appears unserviceable.
Be sure the drive chain has dried completely beforelubricating.
Lubricate the drive chain with drive chain lubricant [2]designed specifically for use with O-ring chains, #80 –90 gear oil or equivalent.
Do not use a chain lubricant NOT designed specificallyfor use with O-ring chains to lubricate the drive chain.
Wipe off the excess oil or drive chain lubricant.
TORQUE:88 N·m (9.0 kgf·m, 65 lbf·ft)
TORQUE:27 N·m (2.8 kgf·m, 20 lbf·ft)
[2]
[1]/[3][5] [4]
[2]
[1]
[2]
[1]
3-13
dummyheaddummyhead
MAINTENANCE
SPROCKET INSPECTIONRemove the drive sprocket cover (page 2-6).
Inspect the drive and driven sprocket teeth for wear ordamage, replace if necessary.
Never use a new drive chain on worn sprockets.Both chain and sprockets must be in good condition, ornew replacement chain will wear rapidly.
Check the attaching bolts and nuts on the drive anddriven sprockets.
If any are loose, tighten them to the specified torque.
Install the drive sprocket cover (page 2-6).
DRIVE CHAIN SLIDERU type only: Remove the drive chain cover (page 2-6).
Remove the drive sprocket cover (page 2-6).
Check the drive chain slider [1] for wear or damage.
The drive chain slider must be replaced if it is worn tothe wear limit indicator [2] or wear limit line [3].
For drive chain slider replacement (page 17-10).
TORQUE:Drive sprocket fixing plate bolt [1]:
10 N·m (1.0 kgf·m, 7 lbf·ft)Driven sprocket nut [2]:
50 N·m (5.1 kgf·m, 37 lbf·ft)
[1]
[2]
[1]
[2]
[3]
3-14
dummyheaddummyhead
MAINTENANCE
BRAKE FLUID
Spilled fluid can damage painted, plastic or rubberparts. Place a rag over these parts whenever thesystem is serviced.
• Do not mix different types of fluid, as they are notcompatible with each other.
• Do not allow foreign material to enter the systemwhen filling the reservoir.
• When the fluid level is low, check the brake pads forwear (page 3-16).
• A low fluid level may be due to wear of the brakepads. If the brake pads are worn and caliper pistonsare pushed out, this accounts for a low fluid level. Ifthe brake pads are not worn and fluid level is low,check the entire system for leaks (page 3-17).
FRONT BRAKETurn the handlebar to the left so that the reservoir islevel and check the front brake fluid level through thesight glass.If the level is near the "LOWER" level line [1], fill therecommended brake fluid.
Remove the following:
– Screws [2]– Reservoir cover [3]– Set plate [4]– Diaphragm [5]
Add DOT 3 or DOT 4 brake fluid from a sealedcontainer to the casting ledge [1].
Install the diaphragm, set plate and reservoir cover.Install and tighten the cover screws to the specifiedtorque.
[3][2]
[1][4]/[5]
TORQUE:1.5 N·m (0.2 kgf·m, 1.1 lbf·ft)
[1]
3-15
dummyheaddummyhead
MAINTENANCE
REAR BRAKESupport the motorcycle on a level surface, and checkthe rear b
Recommended