View
78
Download
2
Category
Preview:
Citation preview
NTU ESOE
Energy HarvestingEnergy HarvestingDevicesDevices
WenWen--JongJong WuWuDepartment of Engineering Science and Ocean EngineeringDepartment of Engineering Science and Ocean Engineering
National Taiwan UniversityNational Taiwan UniversityTel: +886Tel: +886--22--3366576433665764
EE--mail : mail : wjwu@ntu.edu.twwjwu@ntu.edu.tw
NTU ESOE
MEMS GeneratorMEMS Generator
Si
Fixed End
Proof Mass
Si
DigitateElectrode
Supporting Membrane
PZT
Proof Mass
NTU ESOE
MEMS Generator Impedance CharacteristicsMEMS Generator Impedance Characteristics
• Annealing: 650°C / 120 minutes • Poling:
poled under 200V @ 150 °C60 minutes
NTU ESOE
NSCNSC--CNRS International Joint ProjectCNRS International Joint Project
• French side (CNRS) - PI: François COSTA, SATIE Lab Title: Micro-générateurs pour bio-micro-systèmes, basés sur la récupération de l’énergie acoustique grâce à des couches de PZT déposées sur des membranes ou des poutres en silicium.
• Taiwan side(NSC)-PI: Wen-Jong Wu,Co-PI: P.Z. ChangTitle: Micro Generator of Power Harvesting by Vibrations using Innovative PZT Deposition Process
NTU ESOE
Using PZT powder in diameter small than 0.5 μm.
Pressure difference between the destination room and powder room:150mmHg ~ 400mmHg
The deposition rate is 0.1 μm/min on a 50x70 mm2 area.
Could be deposited on Si, SiO2, SU-8, glass, polyimide, ITO, Cu, Pt, Au, and Al , etc.
The process is conducted in room temperature.
Annealed in 550~650°C furnance after the jet sprayed process.
Aerosol Jet Sprayed PZT Deposition Chamber Aerosol Jet Sprayed PZT Deposition Chamber
NTU ESOE
Material PropertyMaterial PropertyXRD PE curve
Dielectric constant Dielectric loss
NTU ESOE
A 15um*800um*650um PZT Released StructureSi
KMPR
PZT(a)KOH backside wet etch
(b)Deposit bottom electrode
(c)Pattern PZT thick film by lift-off.
(d)Deposit Top electrode
(e)Suspend the transformer structure and annealing
PZT
AIR
(residual glue)A freestanding PZT membrane without supporting.
The minimum linewidth of 10 μm thickness PZT structure is 30 μm in our work.
NTU ESOE
230
250
270
290
310
330
350
370
2500000 2700000 2900000 3100000 3300000 3500000 3700000 3900000
Frequency (Hz)
Impe
denc
e (O
hm)^
-1
-79.00
-78.00
-77.00
-76.00
-75.00
-74.00
Deg
ree
( o
)
Impedence
Phase
2.80 MHz
3.50 MHz 3.72 MHz
3.82 MHz
3.79 MHz
ANSYS Simulation Mode ShapesANSYS Simulation Mode Shapes
NTU ESOE
MMicro Piezoelectric Devices Design and Fabrication Flowicro Piezoelectric Devices Design and Fabrication FlowMicro Piezo Devices
Testing
Device Design
Post Process Design
Annealing Test
Fabrication
The cantilever structure verify that the material properties of jet spray deposited PZT is closed bulk PZT material, and thus the behavior can be precisely simulated and predicted by ANSYS.
The design and fabrication flow of micro piezoelectric devices are as the right figure.
Application for now: Micro power harvesting device and micro piezoelectric transformer, and many other devices can be tried in the future
TransformerCantilever
NTU ESOE
Energy Harvesting from Ambient Random VibrationsEnergy Harvesting from Ambient Random Vibrations
• It is an utmost goal to power wireless sensor nodes from energy scavenged from the ambient environment.
• The energy harvesting from ambient vibration with piezoelectric cantilever beam structure has been proven to be one of the best approach toscavenge energy from ambient vibrations due to the high energy density nature of piezoelectric materials.
• The state of the art vibration energy harvesting devices can generate power in milliwatts level.
NTU ESOE
Theoretical AnalysisTheoretical Analysis• The mechanical and electrical behavior around the 1st resonant
frequency in bending direction which power harvesting devices usually adopted can be expressed in equivalent circuit model.
– The transformer in the circuit model denotes a mechanical to electrical energy transformation.
– The voltage source E1 denotes a external force– The RmLmCm in mechanical branch denotes equivalent circuit parameters in the
mechanical oscillation. – The C0 in the electrical side denotes the static capacitance of parallel electrode plates
which is shunted with the external electrical load.
FixedFree
E1C0
Lm CmRm
LOAD
Mechanical Branch Figure 1: Beading at 1st Mode
Figure 2: Equivalent circuit Modal
NTU ESOE
Experiment architectureExperiment architecture• CC1010
– RF transceiver/ 8051 compatible microcontroller– 2 UART (Universal Asynchronous Receiver / Transmitter) – 3 channel 10Bit ADC– Programmable transmission power
-20dBm to 10dBm for different transmission range
14.7MHz crystal
32KHz crystal
Antenna
Connectors reserved for sensor
Chipcon CC1010
Tunable capacitor
Power connector
NTU ESOE
Experimental SetupExperimental Setup
• The experimental setup is composed of a piezoelectric cantilever beam clamped at one end fixed on a vibrating shaker.
• The piezoelectric cantilever beam used here is bimorph type.– The upper panel was used in the frequency tuning purpose.– The lower piezoelectric panel on the beam is then used to harvest energy.
Function Generator
Power Amplifier Vibration Shaker
Bimorph Piezoelectric
Fixed Support End
Microprocessor of the Sensor Netwoks
Harvesting Energy Device
Cantilever Beam
Choosing Different Load
Power Harvesting Device Experimental Setup
NTU ESOE
Results of Network Analysis Results of Network Analysis • The two extreme conditions short circuit and open circuit conditions, the
resonant frequencies are 91.5Hz and 94.5Hz respectively. • The 3Hz range is the tunable bandwidth on this system.
– Resonant frequency of the system can be changing in this range by switching in different capacitive loads.
Networks Signal Analysis
30
32
34
36
38
40
42
80 85 90 95 100 105 110 115Frequency(Hz)
Gai
n(dB
)
Shor t C ircu it
Using Tunab le Frequency System
Oper C ircu it
Networks analysis result
NTU ESOE
Results of Random Frequency ExcitationResults of Random Frequency Excitation• The device excited under random frequency from 80Hz to 115Hz.
– The average harvesting output power is about 1.53mW with the tuning resonant frequency system turned off and 1.95mW with the resonant frequency tuning system turned on.
– The average harvesting output power increases about 27.4% with the real-time resonant frequency tuning system under random excitation.
Random frequency from 80Hz to 115Hz
0
0.5
1
1.5
2
2.5
3
3.5
4
0 1000 2000 3000 4000 5000 6000 7000
Time(s)
Vol
tage
(V)
No tunable frequency system
With tunable frequency system
Random frequency excitation from 80Hz to 115Hz
1.53mW1.95mW
27.4%+
NTU ESOE
Piezo-Transformer
DrivingCircuit
Different typesPiezoelectric Transformer
Self-FilteringModal Electrode
PFC Output 400V
Control Circuit
Constant Current Control
Rigid Support
Innovative P.T.Innovative P.T.--based Inverterbased Inverter
Effieciency:90% !!Phase Control
NTU ESOE
• Square wave input Sine wave output
• Modal self-filtering effect
Using P. T. PZTUsing P. T. PZT--MM--5353--2 to light 680mm CCFL2 to light 680mm CCFLInput voltage Output voltage Output voltage Input voltage
NTU ESOE
Thank You!!Thank You!!
Recommended