View
214
Download
0
Category
Tags:
Preview:
DESCRIPTION
(thicker glass) on a clean flat surface to prevent scratching. Insert metal top cap through all four small holes. into short tubes. Please ensure that flat foot moulding is securely inserted. Cable tidy cover can be 'snap-fit' over cable tidy mouldings & to hide cables once equipment is installed.
Citation preview
AUDIO VISUAL SUPPORT
MODEL: AD2/105-s & AD2/105-PB
ASSEMBLY INSTRUCTIONS
Alphason Designs LimitedAlphason House, Bolton Road, Atherton, Greater Manchester M46 9AW UKTel: +44 (0)1942 885600Fax: +44 (0)1942 876955
www.alphasondesigns.com 03 10/05issue 181718
�BEFORE STARTING THIS
ASSEMBLY PLEASE TAKE TIME TO FAMILIARISE YOURSELF
WITH THE COMPONENTSLISTED ON THE BACK PAGE
Model shown: AD2/105-s
Place top glass shelf (thicker glass) on a clean
flat surface to prevent scratching. Insert metal top
cap through all four small holes.
Remove nuts and washers from threaded rods
and screw into four top caps . Tighten by hand.
Assemble tube end plugs over four threaded
rods and onto glass. Ensure recessed side of tube
end plug is against glass.
Fit long tubes over threaded rods and
on to tube end plugs .
Fit tube end plugs over threaded rods and
locate into long tubes .
Locate glass shelf over threaded rods & on
to tube end plugs .
Insert plastic spacers over rods and into
holes in glass shelf .
Fit tube end plugs over threaded rods with
recessed side against glass shelf.
Assemble short tubes over threaded rods and
locate tube end plugs into tube ends.
STAGE 1
STAGE 3
STAGE 2
03 10/05issue 181718
x4 x4
x4x4
•
•
•
•
•
•
•
•
•
1.
2.
3.
RECESSED
SIDE OF
TUBE END
PLUG .
e
e
D
A
i
i
h
h
i
i
C
C
B
B
i
n
n
h i
i
i
i
x4x4ni
e
i
i
i
i
ii
C
D
DD
D
C
CC
ii
i
n
n
nn
B
i
h
hh
h
ii
e
e
A
e
Insert flat foot mouldings into short
tubes. Please ensure that flat foot moulding
is securely inserted.
Fit washers over threaded rods and
secure assembly with M8 half nuts .
Tighten using box spanner .
TAKE CARE NOT TO OVERTIGHTEN THE
ASSEMBLY
STAGE 4
Cable tidy cover can be 'snap-fit' over cable
tidy mouldings & to hide cables once
equipment is installed.
Once installed, the cable covers can be rotated
through 360° to allow easy access for cables.
STAGE 6
Carefully turn assembly over so that it rests on
foot mouldings .
Insert short cable tidy moulding firmly into
large hole in top shelf .
Insert long cable tidy mouldings firmly into
large hole in glass shelf .
STAGE 5
•
•
•
•
•
5.
4.
6.
•
•
03 10/05issue 181718
x1 x2
x4x4 x4
f
BB
AA
j
j
j
k
k
k l
l
l
m
g
f
o
g
g
gg
g
f
f
j
ff
j
l
l
k
k
jj
m
COMPONENT DESCRIPTION QTY PACKED BY
MODEL: AD2/105-s & AD2/105-PB
CERTIFICATE OF CONFORMITY
TOP PANEL 1A
4RODe WASHER
h TOP CAP
PRE-PACKAD2/105-s - 200269AD2/105-PB - 200240
j FLAT FOOT MOULDING
k LONG CABLE TIDY MOULDING
l SHORT CABLE TIDY MOULDING
m CABLE TIDY COVER
f HALF NUTg
03 10/05issue 181718
SHELF PANEL 1B
LONG TUBE 4C
SHORT TUBE 4D
1BOX SPANNERo
AD2/105-s - 141099AD2/105-PB - 141111
AD2/105-s - 141089AD2/105-PB - 141112
This document is your guarantee that the product has reached you in the highest of quality standards. Should you have any cause for complaint please return this document with your correspondence to the address given at
the bottom of the front page.
4n PLASTIC SPACER
12
4
4
i TUBE END PLUG
1
1
1
�
COMPONENT DESCRIPTION QTY PACKED BY
PRE-PACK PDI
4RODe WASHER
h TOP CAP
j FLAT FOOT MOULDING
k LONG CABLE TIDY MOULDING
l SHORT CABLE TIDY MOULDING
m LONG CABLE TIDY COVER
f HALF NUTg
03 10/05issue 181718
LONG TUBE 4C
SHORT TUBE 4D
1BOX SPANNERo
111334
This document is your guarantee that the product has reached you in the highest of quality standards. Should you have any cause for complaint please return this document with your correspondence to the address given at
the bottom of the front page.
4n PLASTIC SPACER
12
4
4
i TUBE END PLUG
202182
202161
105260
105055
129101
202217
1
1
1
MODEL: AD2/105-s & AD2/105-PB
AD2/105-s - 202120 x3AD2/105-PB - 202224 x3
AD2/105-s - 202216AD2/105-PB - 202245
AD2/105-s - 180329AD2/105-PB - 180341
Recommended