View
3
Download
0
Category
Preview:
Citation preview
Agricultural Quality Assessment Division QAD 631 Procedure
Marketing 1400 Independence Avenue SW, Stop 0258 August 31, 2018
Service Washington, DC 20250 Page 1 of 14
FURTHER PROCESSING CERTIFICATION PROGRAM
INDUSTRY GUIDELINES FOR PREPARATION OF QUALITY CONTROL
PROGRAM FOR MEAT AND POULTRY
Purpose
The purpose of this procedure is to set forth policies, procedures and guidelines for the
certification of U.S. Department of Agriculture (USDA) donated red meats and poultry under the
Further Processing Certification Program (FPCP).
The following guidelines provide the criteria for approving and monitoring documented quality
control systems used by the processor when participating in this program. A quality control
system is defined as all processes that work together to produce one or more products.
Scope
The FPCP offers red meat and poultry further processors a uniform USDA/AMS certification.
This program is intended to add value to further processed donated red meat and poultry
commodities through a uniform process control while reducing costs. A minimum of one USDA
grader per shift will be required to monitor the FPCP operations of the production facility. The
FPCP emblem may be used in advertising and promotional literature for finished goods
distributed to states, as well as commercial products produced with AMS Verification. All
further processors who participate in the FPCP are required to have an approved Quality Control
(QC) program prior to using the FPCP emblem. It is the processor’s responsibility for
developing a QC program in accordance with guidelines established by AMS. This document
will not replace the manufacturer’s responsibility to adhere to all other federal policies and safety
regulations (e.g., FSIS - HACCP and FDA Standard of Identity, etc.). Each processor must
secure an approved National Processing Agreement (NPA) with FNS. An acceptable FPCP QC
program is one that establishes effective controls for each verification element following the
guidelines in this document.
References
The following referenced documents are used for the application of this document. The latest
edition of the referenced document (including any amendments) applies.
7 Code of Federal Regulations (CFR), Part 250, Donation of Foods for Use in the United States,
its Territories and Possessions and Areas Under its Jurisdiction, Section 30, State Processing of
Donated Foods
End Product Data Schedule (EPDS)
State Processing Handbook
National Institute of Standards and Technology (NIST), Handbook 44, Specifications,
Tolerances, and Other Technical Requirements for Weighing and Measuring Devices
Agricultural Quality Assessment Division QAD 631 Procedure
Marketing 1400 Independence Avenue SW, Stop 0258 August 31, 2018
Service Washington, DC 20250 Page 2 of 14
Policy
Food and Nutrition Service (FNS) regulations (7 CFR Part 250, Donation of Foods for Use in the
United States, its Territories and Possessions and Areas Under its Jurisdiction, Section 30, State
Processing of Donated Foods) require that all processing of donated meat products be performed
by the AMS verification service in plants operating under Federal Inspection (or State
equivalent). Additionally, the AMS policy is to ensure USDA donated product is properly
handled, processed according to specification, and traceable from school district to raw product
supplier.
I. Definitions
Agricultural
Marketing Service
(AMS)
The USDA agency responsible for purchasing surplus
commodities such as meat, poultry, fruits and vegetables.
AMS also provides end product certification that, at a
minimum, certifies against non-diversion and non-substitution
and provides for metal detection of donated food.
Backhaul Commodities that are physically picked up from a distributing
agency (DA) or recipient agency (RA) for processing.
Batching
The process of combining the same kind of non-substitutable
donated food from more than one State RA during a production
run. Batching is only permitted with diverted raw material, not
backhauled product.
Child Nutrition (CN)
Labeling Program
A voluntary program administered by FNS that evaluates
formulations to determine the contribution toward the meal
pattern requirements. It also protects the school from
exaggerated product claims and provides a warranty against
audit claims, if used according to manufacturer’s directions.
Commodity
Equivalent
End product that is made using commercial meat which is
equal to or better than the USDA commodities.
Commingling
The act of storing, combining, or blending commercial food
and substitutable donated food together into a single inventory
at a processor’s plant. Processors must receive approval from
FNS to commingle foods on a national level. Commingling is
only permitted with diverted raw material, not backhauled
product.
Corrective Action Action to eliminate the cause of a detected nonconformity (NC)
or other undesirable situation.
Distributing Agency (DA)
The agency, usually an agency of State government, which
enters into an agreement with FNS for the distribution of
donated food to eligible recipient agencies.
End Product A finished product containing any amount of donated foods
that have been commercially processed.
Agricultural Quality Assessment Division QAD 631 Procedure
Marketing 1400 Independence Avenue SW, Stop 0258 August 31, 2018
Service Washington, DC 20250 Page 3 of 14
End Product Data Schedule
(EPDS)
A standard form that describes the finished end product being
produced. Information detailed on this form includes
formulation, quantity of donated food needed to produce a
specific number of units of end product, packaging and yield
information.
First In First Out (FIFO) An inventory control system based on the production.
Food and Nutrition Service
(FNS)
The agency responsible for administering further processing of
donated commodities.
Food Safety and Inspection
Service (FSIS)
The USDA agency whose primary mission is to inspect the
wholesomeness of meat and poultry products.
National Processing
Agreement (NPA)
A contract between the further processor and FNS to produce
finished products.
Non-Conformance (NC) A deviation from program requirements.
FPCP Further Processed Certification Program.
Quality Control Employee
Designated company employee other than the plant owner,
manager, foreman, or supervisor, authorized to examine
product and to supervise production, processing, labeling, and
other functions of officially identified meat or poultry products.
Quality Control Record
Document of any quality check the processor performs under
the FPCP program and officially records either on an approved
paper form or electronic system.
Rework
Wholesome, salvageable product generated during a production
run that is not acceptable as the specified product. Product
such as broken patties or nuggets, or other defects such as
missing breading, lumps, and ridges would be classified as
rework product.
Substitution
The act of replacing USDA donated commodities with
commercially purchased materials of the same generic identity,
and of equal or better quality to the donated food provided by
USDA.
USDA Record Check
The USDA grader shall review processor’s documentation to
determine if the specific examination was performed,
accurately documented and within the specified tolerances as
required by the FPCP.
USDA Verification Check
The USDA grader shall observe designated processor’s
employee perform and document the specific task as required
by the FPCP.
Agricultural Quality Assessment Division QAD 631 Procedure
Marketing 1400 Independence Avenue SW, Stop 0258 August 31, 2018
Service Washington, DC 20250 Page 4 of 14
II. Submission of Proposal
Prospective processors are required to submit a written proposal prior to the commencement of
production, addressing each requirement area and outlining specific procedures used to ensure
that these requirements are met while processing products under the FPCP. Processors shall
submit proposals to:
Richard.Lawson@ams.usda.gov
Darrell.Dowd@ams.usda.gov
Develop and maintain individual programs that address each requirement area outlined in the
FPCP using the Plan, Do, Check, Act (PDCA). Programs, at a minimum, shall include
requirements specified in this Procedure. If a section does not apply, indicate under the section
why that section is not applicable. Further processors may include additional programs and
requirements not listed in this program, which may be monitored and verified by the USDA
grader.
Each Processor must ensure that all state participation agreements are signed and dated by the
state representative and the further processor and that all EPDS are signed by the further
processor as well as the L&P/QAD designee.
As applicable each processor must have an approved substitution plan.
Facility management must appoint, in writing, a member of the organization’s management who
shall ensure that the processes needed for the quality management system are established,
implemented and maintained in accordance with the procedures outlined in this document. This
management representative shall also serve as a liaison with AMS on matters relating to the
quality management system. Additionally, facility management must provide the USDA grader
with a letter certifying that all personnel performing authorized certification activities have been
provided with training to achieve the necessary competence so that they are aware of the
relevance and importance of their activities and how they contribute to the achievement of the
quality objectives.
Develop and maintain a traceability program, capable of tracking product from raw product
supplier to end item recipient and vice versa on a per case basis. This may be approved by either
manually operated or electronic programs (those using bar coding and scanning devices).
Identify donated food clearly, through all stages of production, storage and shipment.
III. Cover Page
The cover page must contain the following information:
1) Company name.
Agricultural Quality Assessment Division QAD 631 Procedure
Marketing 1400 Independence Avenue SW, Stop 0258 August 31, 2018
Service Washington, DC 20250 Page 5 of 14
2) Full address of the further processing plant location where EPDS products are
manufactured.
3) Establishment number.
4) Objective of the program.
5) Record Retention – State how long data will be maintained.
Ex.: QC records for FPCP products will be retained for a minimum of one year.
6) Commitment to make all records and information generated as a result of the
program available to USDA officials.
7) Signature of the establishment’s official responsible for the program (e.g.,
President or Quality Control Manager).
8) A statement that QC personnel have the authority to halt production and restrict
shipment of product if standards established in this program are not met.
IV. Detailed Information Guidelines
A. Products covered
List the name(s), including product codes of all EPDS produced by the plant. When
new products are approved, the list must reflect the changes. A copy of the revised list
must be submitted to AMS. The grader will evaluate the revised QC program and
notify the Regional office through the appropriate channels.
B. Equipment
1) Scales
a. Develop and maintain a scale verification program that is certified by state or
local government officials or an equivalently registered or licensed technician
annually. Ensure that each scale is properly identified with the certifier’s
initials and date of certification.
b. Ensure that scales are checked for accuracy in accordance with the National
Institute of Standards and Technology (NIST), Handbook 44, Specifications,
Tolerances, and Other Technical Requirements for Weighing and Measuring
Devices.
c. Ensure that scales are calibrated within tolerance daily prior to the start of
production with certified weights.
d. Maintain copies of licenses or certificates of all in-house technicians and a
scale certification log for review by the grader.
Agricultural Quality Assessment Division QAD 631 Procedure
Marketing 1400 Independence Avenue SW, Stop 0258 August 31, 2018
Service Washington, DC 20250 Page 6 of 14
e. Describe the method used for verifying each piece of equipment and include a
statement about traceability to a national standard.
f. State the frequency of checks.
g. Identify the corrective action taken when the testing/measuring device(s) are
out of balance.
2) Grinders and Blenders
a. Ensure that the grinding and blending systems producing products are free of
non-program materials (i.e. uncertified commercial meat).
b. Perform a complete “clean–up” prior to re-introducing red meat or pork
program materials, if non-program materials are introduced into grinders or
any other equipment used in the processing of products for the FPCP.
3) Extruder/Elimination Systems
a. Ensure that extruder/elimination systems are attached to grinder heads and
function in accordance with manufacturer specifications. Manufacturer
specifications shall be available to the grader upon request.
b. Ensure that all extruded material is clearly identified and disposed of properly.
4) Thermometers
a. Ensure that thermometers are calibrated daily prior to the start of production.
b. Maintain thermometer calibration logs for review by the grader.
5) Metal Detectors
a. Ensure that finished product passes through a functioning, in-line metal
detector/x-ray prior to initial placement into shipping containers.
b. Ensure that metal detectors/x-ray are calibrated in accordance with
manufacturer specifications.
c. Ensure that metal detectors/x-ray equipment are capable of detecting stainless
steel, ferrous and non-ferrous metals.
d. Declare the type of equipment, location, detection procedure, sensitivity
levels, frequency of validating the equipment, and demonstrate how the
product with metal contamination is excluded from complying product.
6) Packaging and Packing
Product may be checked in-line (pumped or vacuumed), prior to packaging, after
packaging, or after packing using appropriate test strips as follows:
Agricultural Quality Assessment Division QAD 631 Procedure
Marketing 1400 Independence Avenue SW, Stop 0258 August 31, 2018
Service Washington, DC 20250 Page 7 of 14
a. Prior to packaging - nuggets, patties, parts, etc. Testing shall be with a 1.5
mm 440 stainless steel strip.
b. After packaging or packing - bologna, roasts, turkey ham, rolls, nuggets,
patties, or diced product etc. Testing shall be with a 3.0 mm 440 stainless
steel strip.
c. In-line closed systems - Testing shall be with a flexible 3.0 mm 440 stainless
steel test strip through a test port into the center of the detector field.
Alternatively, a flexible 1.5 mm 440 stainless steel test strip inserted into the
detector field at the outside edge of the pipeline may be used.
C. Red Meat Raw Material
Provide the grader with a Certificate of Analysis (COA) prior to the use of Fresh Boneless Beef
(combos) for further processing. Processors should assure their suppliers fax the COA to arrive
at delivery and provide the grader evidence that fat analysis has been conducted and is within the
acceptable range. This evidence may be provided from the supplier or an outside laboratory. A
COA is not required for frozen coarse ground beef as the microbiological analysis is known
before shipment.
Conduct a product examination at the time of processing. The examination shall include, at a
minimum, the following requirements:
1) Condition-Product must not show any evidence of mishandling, such as
defrosting and refreezing, excessive purge, sticky surface slime, freezer burn,
odor and/or discoloration.
2) Age-Beef and pork product with production dates up to 12 months old may be
processed. Product exceeding the age limit will be considered non-substitutable
and may only be processed under full certification.
D. All Raw Material (Red Meat and Poultry)
Continuous Process-Every effort shall be made to complete the processing of product from raw
state to finished cases in continuous production. Processors may carry over product as long as
the following requirements are met:
1) Product is held in clean containers. (Containers that have been washed and are
free of any non-program materials.)
2) Containers are properly identified in accordance with the traceability program.
3) Product temperatures do not exceed 40°F.
4) Product is processed prior to newly ground/formulated product of the same item.
5) Exceptions for equipment failure will be handled on a case-by -case basis.
Agricultural Quality Assessment Division QAD 631 Procedure
Marketing 1400 Independence Avenue SW, Stop 0258 August 31, 2018
Service Washington, DC 20250 Page 8 of 14
E. Formulation Control
1) As applicable to your product, include an example of a batch formulation.
2) State that the formulation used for production will match the formula percentage
or weight as presented on the approved EPDS form.
3) State that the weight of each ingredient, except those mentioned in Section IV.
E.4, will not vary more than 0.5 percent from the required weight designated in
the formula.
Ex: If the formula calls for 40.0 pounds of a seasoning, the allowable
minimum/maximum amount for that formula is 39.8 - 40.2 pounds respectively.
4) Mention that the weight of restricted ingredients, such as phosphates, nitrites,
erythorbates, etc., will not differ from the approved formulation.
5) For CN labeled product, state that no ingredient in the formulation may be
substituted for another. The ingredient name and ingredient sub-listing (if
applicable) must match the EPDS and label.
6) All products must meet the applicable product regulations (e.g., FSIS or FDA
Standard of Identity) and applicable FNS requirements.
7) Indicate that QC will verify compliance with formulas. In addition, the QC
program should mention the number of ingredients that will be checked and how
often a QC person will check the weights of these ingredients.
8) The QC program must state that the formulation will be checked on a random
basis to assure that each ingredient has an equal chance of being selected. State
that whenever a formulation error is found in excess of the tolerance the following
will be done:
a. Immediate corrective and preventive action will be taken for the remaining
product run.
b. The formulated product will be corrected immediately.
c. If correction is not possible for the formulated product, that batch will be used
in other EPDS product.
F. Component Weight Control
Child Nutrition Labeled Products
The raw weights and cooked weights (if product is cooked) must be monitored according to
sections G. and H. This applies to products such as: unbreaded patties, links, unbreaded nuggets,
and many others.
1) Raw Weights - The raw weight is checked on all portions and/or components,
whether the finished product is raw or cooked.
Agricultural Quality Assessment Division QAD 631 Procedure
Marketing 1400 Independence Avenue SW, Stop 0258 August 31, 2018
Service Washington, DC 20250 Page 9 of 14
2) Cooked Weights - Cooked weights are checked and compared with the portion
size stated on the transmittal and on the CN label statement. Weights are also
checked for precooked components of products against information on the label
transmittal.
Ex: A grilled chicken patty would be specified as follows - Raw weight 2.35 oz.
patty; cooked weight 2.25 oz. patty
The QC program will monitor the raw weight per patty and the finished cooked
patty weight identified on the transmittal form each according to the lot, subgroup
size, frequency, and weight tolerances established in Sections G. and H.
G. Lotting
The QC program shall address:
1) Lot Definition – A lot shall be defined for each product code separately. A lot
may be defined as one shift’s production of product.
2) Identification - Lots and sub lots of product are fully identified throughout the
process and the QC program should include a description of how this is done.
H. Subgroup Size (weighing)
1) The QC program shall state the subgroup size and the frequency that samples will
be certified. The subgroup sample size should be a minimum of 5 servings.
Samples should be pulled one hour minimum between samples.
However, the sample size and frequency may be more based on the rate of plant
production1.
2) The QC program shall state the subgroup weight range tolerance. The average
weight of any single subgroup size may vary as follows:
It is recommended but not required to monitor the maximum weight range
tolerance. However, the minimum weight ranges tolerance must be monitored for
each component (e.g., meat patty component, breading component, sauce
component, filling component, crust component, etc.) regardless of how many
components are being monitored.
Subgroup Sample size 5 to 7 8 and over
Weight range tolerance - 10 percent - 8 percent
Agricultural Quality Assessment Division QAD 631 Procedure
Marketing 1400 Independence Avenue SW, Stop 0258 August 31, 2018
Service Washington, DC 20250 Page 10 of 14
Ex: A label states that a serving is four 0.6 oz. chicken nuggets. Therefore, a
subgroup of five servings would total 20 nuggets weighing 12.0 oz. This subgroup
will have a weight range tolerance of 10.80 oz. to 13.20 oz.
3) When a subgroup weight falls below the predetermined minimum weight
tolerance, state all product produced since the last acceptable check will be
reworked when applicable according to section M. or retained and diverted as
non-FPCP labeled product.
4) Indicate that the average of all subgroups taken from one shift of production (one
production lot) must meet or exceed the label and label EPDS requirement. Also
indicate that this applies to raw, cooked, and breaded products, and that each
EPDS product will have its own shift average since combining products is not
allowed.
5) Mention that whenever the shift average (average of all subgroups) of any product
fails to meet the required minimum weight, the entire shift’s production of that
product will be diverted as non-FPCP labeled product or held pending negotiation
for acceptance by L&P QAD according to H.6. (see below).
6) For items that have special regulatory requirements; such as breaded items,
fritters, protein fat-free (PFF) products, meats with marinade or solutions, etc.;
include how these requirements will be monitored in the QC program.
Ex: Breaded products are limited to 30 percent batter/breading of the finished
batter/breaded weight prior to blanching, freezing, or cooking. The QC program
would specify that if the subgroup average of the breaded product exceeds the
regulatory limit by more than three percent per unit, all products back to the last
acceptable check will be retained. If the regulatory limit is 30 percent, the
program would call for the retention of any product that exceeds 33 percent
breading. In addition, the QC program would state that if the shift’s average of all
subgroups exceeds the regulatory limit of 30 percent, the entire shift’s production
of that product will be retained and reworked or relabeled as appropriate
I. Batter/Breading Non CN Labeled
1) AQL Method:
Under this method the batter/breading must not exceed the percent stated on the
EPDS of any sample.
2) Shift Average:
Under this method, a tolerance of +/- 3% of the target batter/breading percentage is
allowed for individual AQL samples, provided the shift average for batter/breading
present does not exceed the target percentage listed on the EPDS or specification.
Agricultural Quality Assessment Division QAD 631 Procedure
Marketing 1400 Independence Avenue SW, Stop 0258 August 31, 2018
Service Washington, DC 20250 Page 11 of 14
Product represented by individual AQL samples not meeting the +/- 3% tolerance is
not eligible for certification and is rejected for use immediately. The AQL results for
any rejected sampling period will not be used in the calculation for the shift average.
To minimize the amount of product that would be subject to retention for being out of
compliance, it is permissible for the processor to remove AQL sampling periods that
caused the shift average to not comply with the requirements. Product removed to
achieve shift average compliance is not eligible for certification.
J. Cook Temperatures
Product cooking temperature must be in accordance with the company’s HACCP Plan.
K. Case Net Weights
Ensure that marked case net weights on the container label meet the minimum requirements
specified on the appropriate EPDS. The following procedures shall be used when test weighing
on an online basis.
1) Proper weighing equipment must be made available at established weighing
stations where unbiased sampling can be accomplished.
2) Tare weight shall be established.
3) Select and weigh five containers each sampling interval.
4) The sample weights, minus the tare weights, shall be totaled, and the average net
weight calculated for each sampling interval.
5) The acceptance criteria for each sampling interval are based both on the
individual and average net weights. The minimum for individual shipping
containers is 1 percent below the marked weight. Additionally, the average net
weight for the five shipping containers must meet or exceed the marked weight.
L. Packaging and Labeling
Ensure that product is identified in accordance with the traceability program, that product is
packaged in accordance with the appropriate EPDS, and that the label is legible, contains the
FPCP emblem and is located on the front panel.
Each lot will undergo an examination for packaging and packing defects. Primary containers will
be examined for cuts, tears, holes, improper closure, excess moisture, and dirty, smeared, or
stained areas affecting the usability of the container. Shipping containers will be examined for
condition, labeling, and markings. The examinations will be according to the criteria listed in the
United States Standards for Condition of Food Containers.
Ensure that the labels are placed on the face panel. They must contain, at a minimum, the
production date, product name, product code, case net weight, (Red Meat) donated commodity
Agricultural Quality Assessment Division QAD 631 Procedure
Marketing 1400 Independence Avenue SW, Stop 0258 August 31, 2018
Service Washington, DC 20250 Page 12 of 14
statement "Contains Commodities Donated by the USDA," and "This Product Shall Be Sold Only
to Eligible Recipient Agencies."
M. Non-Conforming Product (Retained and Reworked Control)
The QC program shall state when and how product is retained due to short weights or an error in
formulation.
Ex: All retained products are tagged with a company tag and placed in the area designated for
retained product. The QAD supervisor or NMFS CSO is notified.
N. Monitoring Procedure
For procedures such as, calibration checks; fat control; formulation control; component weight
control and subgroup size include the following information:
1) Who (by title) is performing the procedure
2) What is the sampling rate (how many and how often)
3) What are the step-by-step procedures that are to be used
4) How and where the results are to be recorded
5) What to do if the product does not meet set target
O. Record Keeping Procedure
1) Identify person responsible for keeping QC records.
2) All information and data generated by this program should be clearly and
accurately recorded. A sample of copies of all forms, tags, and charts used must
be included as part of the program (dates approved).
Ex: Scale Calibration Form
Component (s) Weight Form
Formulation Control Form
Rework Form
Hold Tag
3) All records should be stored in a convenient place and available to QAD
Supervisors upon request.
4) When revisions are made to an existing approved FPCP QC program, such as
changes in processing and monitoring procedures, the QC program must be
Agricultural Quality Assessment Division QAD 631 Procedure
Marketing 1400 Independence Avenue SW, Stop 0258 August 31, 2018
Service Washington, DC 20250 Page 13 of 14
submitted to the Quality Assessment Division, National Office prior to
production. The processor must provide the following:
a. A letter requesting approval and identifying revisions.
b. Documentation supporting the revisions (i.e., documents describing changes
in monitoring and control procedures, purchase of new equipment that may
affect processing procedures, etc.).
P. Noncompliances
Any noncompliance noted during the Grader’s verification checks shall be addressed
immediately. Product failing to meet requirements shall be placed under retention until the
product is brought into compliance or until applicable USDA markings and product
identification have been removed. A follow-up sample may vary between 10 minutes and one
hour after QC advises the Grader that corrections have been made. If the follow-up sample is
satisfactory, sampling will resume at the current monitoring frequency. If product is not in
compliance, the Grader shall contact his/her Supervisor. The Supervisor will consult with the
Regional Director and National Supervisor, to determine what additional corrective action is to
be taken.
Additionally, corrective action must be documented and performed by the plant to prevent any
future occurrences. A copy of the corrective action is to be provided to the Grader, Supervisor
and National Supervisor.
To allow for processing anomalies, the processor is limited to two separate occasions of
noncompliance found in verification checks. If three separate occasions of noncompliance’s are
found through verification checks within a six-month period, the processor is no longer eligible
for the FPCP program and full grading and certification duties will revert back to the resident
USDA grader(s). The Grader shall document each noncompliance in writing to the National
Supervisor. Information to include shall be the date and the descriptions of the noncompliance’s
with copies of the corrective action taken by the plant. This report is due within 10 working days
after the third noncompliance takes place.
The Grader shall advise the Supervisor and National Supervisor regarding any discrepancies that
could compromise the integrity of the FPCP program.
Q. Meetings
The processor shall schedule and participate in FPCP meetings, a minimum of once a month;
discuss program developments, proposed amendments, etc.; record meeting minutes and provide
copies to the USDA grader; forward copies of meeting minutes to the USDA grader, FPCP
coordinator, Supervisor, and all participants in the meeting.
Agricultural Quality Assessment Division QAD 631 Procedure
Marketing 1400 Independence Avenue SW, Stop 0258 August 31, 2018
Service Washington, DC 20250 Page 14 of 14
R. Termination of FPCP
The FPCP may be terminated at any time by plant management upon written or verbal notice to
the Supervisor. If voluntarily terminated at plant management’s request, they may request
reinstatement of the program within six months of the termination date. Approval of
reinstatement will be at the discretion of the National Supervisor, Quality Assessment Division.
FPCP may be terminated by USDA for infractions which indicate a lack of control by the plant.
Such infractions include, but are not limited to:
1) Failure to make QC personnel available as needed to meet minimum online
sampling requirements.
2) Interference or attempts by plant management or other personnel to influence QC
personnel in the performance of their duties.
3) Repeated instances where officially identified product is packed and not
adequately sampled by the QC personnel.
4) Repeated instances where officially identified product packed under QC
supervision fails to meet requirements when verified by USDA.
5) Lack of control and/or monitoring of non-complying product.
Upon determination by the National Supervisor, QAD that sufficient evidence exists to terminate
the FPCP, the National Supervisor, is to notify the plant in writing. The letter will state the
specific reason(s) for the termination. Depending on the seriousness of the situation, verbal
notice may be given of the immediate termination of the program. Termination action shall not
be taken without the concurrence of the Regional Director. If terminated by USDA, the program
may not be reinstated for at least one year, except at the discretion of the National Supervisor.
S. Contact Information
Richard.Lawson@ams.usda.gov
Darrell.Dowd@ams.usda.gov
______________________
Richard H. Lawson, National Poultry Supervisor
Quality Assessment Division
Livestock and Poultry Program
In accordance with Federal civil rights law and U.S. Department of Agriculture (USDA) civil rights regulations and policies, the USDA, its Agencies, offices, and
employees, and institutions participating in or administering USDA programs are prohibited from discriminating based on race, color, national origin, religion, sex,
gender identity (including gender expression), sexual orientation, disability, age, marital status, family/parental status, income derived from a public assistance
program, political beliefs, or reprisal or retaliation for prior civil rights activity, in any program or activity conducted or funded by USDA (not all bases apply to all
programs). Remedies and complaint filing deadlines vary by program or incident.
Persons with disabilities who require alternative means of communication for program information (e.g., Braille, large print, audiotape, American Sign Language,
etc.) should contact the responsible Agency or USDA's TARGET Center at (202) 720-2600 (voice and TTY) or contact USDA through the Federal Relay Service at
(800) 877-8339. Additionally, program information may be made available in languages other than English.
To file a program discrimination complaint, complete the USDA Program Discrimination Complaint Form, AD-3027, found online at How to File a Program
Discrimination Complaint and at any USDA office or write a letter addressed to USDA and provide in the letter all of the information requested in the form. To
request a copy of the complaint form, call (866) 632-9992. Submit your completed form or letter to USDA by: (1) mail: U.S. Department of Agriculture, Office of
the Assistant Secretary for Civil Rights, 1400 Independence Avenue, SW, Washington, D.C. 20250-9410; (2) fax: (202) 690-7442; or (3) email:
program.intake@usda.gov.
USDA is an equal opportunity provider, employer, and lender.
Recommended