View
214
Download
0
Category
Tags:
Preview:
Citation preview
GroundMed DAQ/DMS TrainingCoimbra
6-12-2011
Andre Quintino DuarteAnibal T. de Almeida
Joao Fong
Summary1. DAQ - Data Acquisition System1.1. Hardware Installation
1.1.1. Devices’ Assemblage1.1.2. Power Connections1.1.3. Communication Connections1.1.4. Sensors Connections
1.2. Software Installation1.2.1. Software Configuration1.2.2. Measuring Utility
2. DMS - Data Management System (NEW)
3. Further Development in Coimbra
4. Questions and Answers
5. Coimbra GroundMed facility visit
1. DAQ - Data Acquisition System
1. DAQ - Data Acquisition System
National Instruments cRIO 9074
1. DAQ - Data Acquisition System
National Instruments cRIO 9074
NI 9217NI 9219
NI 9871
1. DAQ - Data Acquisition System
DAQDAQ
1. DAQ - Data Acquisition System
DAQDAQ
Brunata Thermal Meters
PyranometerIndoor/Outdoor
Temperature Sensors
Humidity Sensor
Carlo Gavazzi Meters
1. DAQ - Data Acquisition System
DAQ
DAQ
DAQSyste
m
DAQSyste
m
1. DAQ - Data Acquisition SystemSeptemes les
Vallons,France
DAQSyste
m
DAQSyste
mDAQSyste
m
DAQSyste
mDAQSyste
m
DAQSyste
mDAQSyste
m
DAQSyste
mDAQSyste
m
DAQSyste
mDAQSyste
m
DAQSyste
mDAQSyste
m
DAQSyste
mDAQSyste
m
DAQSyste
m
Oradea, Romenia
Coimbra, Portugal
Benedikt, Slovenia
Valencia, Spain
Barcelona, Spain
Padova,Italy
Athens,Greece
InternetInternet
InternetInternet
InternetInternet
InternetInternet
InternetInternet
InternetInternet
InternetInternet
InternetInternet
DMS Serve
r
DMS Serve
r
GroundMed
WebSite
GroundMed
WebSite
1.1. Hardware Installation1.1.1. Device’s Assemblage
1.1. Hardware Installation1.1.1. Device’s Assemblage
Coimbra
1.1. Hardware Installation1.1.1. Device’s Assemblage
Barcelona
1.1. Hardware Installation1.1.2. Power Connections
1.1. Hardware Installation1.1.3. Communication Connections
1.1. Hardware Installation1.1.3. Communication Connections
Important:- Create an RS-485 network;- Use shield cable with 2 twisted pairs;- Connect shield to ground;- Connect a 120Ω resistor on the edges of the network;- All the devices on the network must have different addresses;- The order is not important.
1.1. Hardware Installation1.1.3. Communication Connections
1.1. Hardware Installation1.1.4. Sensors Connections
1.1. Hardware Installation1.1.4. Sensors Connections
Sensors:- Indoor Temperature Sensor;- Outdoor Temperature Sensor;- Pyranometer;- 2x Brunata (Flow Sensor and 2 Temperature Sensors each);- Current Transformers;- Humidity Sensor (Optional).
1.1. Hardware Installation1.1.4. Sensors Connections
1.1. Hardware Installation1.1.4. Sensors Connections
Important:- Don’t mix Brunata Temperature Sensors;
Temperature ProbesBrunata Display Unit
1.1. Hardware Installation1.1.4. Sensors Connections
Important:- Don’t mix Brunata flow sensors;
Flow sensorBrunata Volume Meter
1.1. Hardware Installation1.1.4. Sensors Connections
Important:- Each Brunata Display Unit has one and only one Volume Meter.
Brunata Volume Meter
Brunata Display Unit
1.1. Hardware Installation1.1.4. Sensors Connections
1.2. Software Installation
1.2. Software InstallationDownload and Install in this order:1. NI cRIO Drivers (about 1600MB)http://joule.ni.com:80/nidu/cds/view/p/id/2411/lang/en;
2. RTAD Application Installer (about 10MB) http://zone.ni.com/devzone/cda/epd/p/id/5986;3. Asynchronous Message Communication (AMC) reference library (about 6MB) (Not required anymore) http://zone.ni.com/devzone/cda/epd/p/id/6091;4. Reference Library for Reading cRIO System Configuration Information (about 6MB) (Not required anymore)http://zone.ni.com/devzone/cda/epd/p/id/1717;5. GroundMed software from ISR available at:
www.isr.uc.pt/~groundmed;6. GroundMed Configuration Utility;7. GroundMed Measurement Utility.
1.2. Software Installation1.2.1. Software Configuration
1.2. Software Installation1.2.1. Software Configuration
Set cRIO Time Zone, Time & Date:1. Load MAX (Measurement & Automation) on the computer;2. Click on Remote Systems, then the cRIO module available;3. On the right size, click below on Time Settings;4. Set your Time Zone, Date and Time;5. Click above on Save.
1.2. Software Installation1.2.1. Software Configuration
Demonstration
1.2. Software Installation1.2.1. Software Configuration
Run RT Application Deployment:
Your cRIO Softwareto install
1) Press Settings under “Application Images”;2) Browse to load the GroundMed downloaded image;3) Press “Deploy”.
1.2. Software Installation1.2.1. Software Configuration
Demonstration
1.2. Software Installation1.2.1. Software Configuration
- 8 different demonstration sites
Does this means 8 different software versions?
1.2. Software Installation1.2.1. Software Configuration
1.2. Software Installation1.2.1. Software Configuration
1.2. Software Installation1.2.1. Software Configuration
1.2. Software Installation1.2.2. Measuring Utility
1.2. Software Installation1.2.2. Measuring Utility
1.2. Software Installation
Demonstration
3. Further Development in Coimbra
3. Further Development in Coimbra
3. Further Development in Coimbra
NI 9472
- 8 Sourcing Digital Outputs;- 6 to 30V range.
Finder Relay20.21.9.024.4000
- 24V Coil Voltage;- 250V AC Rated Voltage.
3. Further Development in Coimbra
5. Coimbra GroundMed facility visit
4. Questions and Answers
5. Coimbra GroundMed facility visit
Thank You
Andre Quintino DuarteAnibal T. de Almeida
Joao Fong
Recommended