View
3
Download
0
Category
Preview:
Citation preview
MODULAR HANDRAIL
P R O D U C T G U I D E
G R P A U S T R A L I A
1 GRP-BR-03 Rev A
HANDRAIL REQUIREMENTS
A U S T R A L I A N S TA N D A R D S
--
250mm
≥9
00
or
≤1
10
0m
m
50
0m
m
1500mm
Max Staunchion Spacing
He
igh
t ra
ng
e
The GRP modular handrail system utilises pultruded round tube (RT50x5), made from premium vinyl
ester resin. This tube forms the top rail, knee rail and stanchions. The rails and stanchions are then
connected using BMC composite fittings. All resin components are fire retardant and contain UV
inhibitors. The fittings are clamped together using stainless steel fasteners provided by GRP Australia.
The standard stock colour is yellow however alternative colours can be supplied depending on the
quantity required.
The modular handrail system is designed to be compliant with the requirements of AS 1657-2013
providing the minimum requirements as set out in the diagram below are maintained.
100mm min10 mm max
2 GRP-BR-03 Rev A
HANDRAIL FITTINGS
PA R T D E TA I L S
Description:
Four angle base foot
Standard Componentry
B O T T O M V I E W S I D E V I E WM H 1 - 2 B A S E I M A G E
B O T T O M V I E W S I D E V I E WM H 1 W A L L M O U N T I M A G E
B O T T O M V I E W S I D E V I E WM H 3 - W C R O S S I M A G E
68
96
10
B O T T O M V I E W S I D E V I E WM H 4 C O N N E C T I M A G E
B O T T O M V I E W S I D E V I E WM H 1 - 4 B A S E I M A G E
110
78
110
78
Ø12
,7
Description:
Two hole base foot
90
110
147,7
Ø12
Ø68
Ø50
126
12
147,7
Description:
Stanchion Wall Mount
130
611
4,5 R
25
150
90
100
Ø8,6
50 50
75
100
Ø65
Ø50
Description:
Wide Three Way Cross
Connection
Description:
Wide Three Way Cross
Connection
150
65
Ø65Ø
50
75
3 GRP-BR-03 Rev A
Description:
90 degree Elbow
B O T T O M V I E W S I D E V I E WM H 2 1 3 5 ˚ E L B O W I M A G E
B O T T O M V I E W S I D E V I E WM H 2 F L E X I M A G E
B O T T O M V I E W S I D E V I E WM H 3 F L E X I M A G E
B O T T O M V I E W S I D E V I E WM H 2 9 0 ˚ E L B O W I M A G E
Description:
135 degree Elbow
Description:
Two Way Flexible Variable
Angle Connector
Description:
Wide Three Way Cross
Connection
92
92
Ø65Ø
65
80
80
135°
Ø65
Ø50
R25
R34
13
1
97
57
65
Ø50
Ø65
57 66
123
B O T T O M V I E W S I D E V I E WM H 4 C O R N E R I M A G E
Description:
Four Way Corner
B O T T O M V I E WM H 3 C O R N E R I M A G E
Description:
Three Way Corner
R7
7
165
6512
115
Ø65
Ø50
115 Ø65
Ø5
0
R7
7
115
S I D E V I E W
4 GRP-BR-03 Rev A
Description:
End tube cap
B O T T O M V I E W S I D E V I E WM H 1 - E N D C A P I M A G E
Ø57
Ø51
R25
57Ø
37.5
Fixing Componentry
Description:
M6 x 30 Barrel Nut & M6 x 40
Pan Head Soc Screw Fastener.
T O P V I E W S I D E V I E WW S 1 0 G X 2 2 I M A G E
T O P V I E W S I D E V I E WM H R - M 6 - 3 0 4 I M A G E
Pan Soc Head Barrel Nut Pan Soc Head Barrel Nut
Description:
10G x 22mm G550 (Stainless
Steel) Wafer Head Screw
T O P V I E W S I D E V I E WR I V E T I M A G E
Description:
Rivet 6 - 8.5 Ø5.1 304 SS
The Barrel Nut and Soc Screw combination is primary fastener used to secure two-part fittings and
tubing. Wafer screws are used to secure tubing into wall or base mounts for additional support. Rivets
are used to attach kick plate to the MH1-Wall Mount and the Mh1-2 Base Mount, which must be no
more than 10 mm from the ground. When securing kick plate to a MH1-2 Base Mount fitting, wafer
screws must be used in order to penetrate the kick plate, fitting and tubing at once. Please note, kick
plate should only be secured following installation of the stamchions.
HANDRAIL FITTINGS
F A S T E N E R S
5 GRP-BR-03 Rev A
HANDRAIL FITTINGS
A S S E M B LY
6 GRP-BR-03 Rev A
Exploded Views
E X P L O D E D A S S E M B L E D
E X P L O D E D A S S E M B L E D
Description:
The 90˚ Elbow is comprised
of 2 part joined at two
points.
Fixings:
2 x MHR-M6-304
Parts/Units:
6 before tubing.
M H 2 9 0 ˚ E L B O W
M H 2 F L E X E L B O W
Description:
The 2 way flexible
connector is joined at a
singular point that acts and
axis.
Fixings:
1 x MHR-M6-304
2 x WS10Gx22
Parts/Units:
4 before tubing.
E X P L O D E D A S S E M B L E D
Description:
The 4 way connector is
joined at 3 points.
Fixings:
3 x MHR-M6-304
Parts/Units:
8 before tubing.
M H 4 - C O N N E C T
7 GRP-BR-03 Rev A
E X P L O D E D A S S E M B L E D
E X P L O D E D A S S E M B L E D
Description:
The 4 angle base foot is
used to secure the handrail.
Fixings:
2 x Wafer Screws required
to secure tubing. If not
specified in design, the base
footing is fixed to substrate
with fixing of clients choice.
Parts/Units:
3 + preferred fixings.
M H 1 - 4 B A S E
M H 1 - W A L L M O U N T
Description:
Wall mount to secure
handrail onto side
substrate/channel.
Fixings:
2 x Wafer Screws required
to secure tubing. If not
specified in design, the base
footing is fixed to substrate
with fixing of clients choice.
Parts/Units:
4 before tubing.
E X P L O D E D A S S E M B L E DM H 3 - F L E X
Description:
3 way flex connectors can
be paired with another 2 or
3 way flex.
Fixings:
3 x M6x25/M6x40
Parts/Units:
8 before tubing
The guide above illustates - depicts key fastening techniques applied to the handrail fitting collection.
Please note, wafer screws are used only to secure tubing in footings, wall mounts and the MH2-Flex
connector. Other fittings do not require additional support if installed properly with the required fixings.
Take care when fastening and ensure the correct use of PPE when necessary.
CORE COMPONENTS
PA R T D E TA I L S
8 GRP-BR-03 Rev A
Kick Plate M Shape
AT
B
A
T B
H E I G H T M M ( B ) W E I G H T ( K G / M )PA R T N O . W I D T H M M ( A )
KP-M100 x 16 x 5
T H I C K N E S S M M
100 16 5.0 1.3
KP-W150 x 15 x 3.21 150 15 3.2 1.6
Round Tube 50 x 5mm
RT50x5 VER25
D
T
MH1-4 Base Mount/Kick plate Connector
50
10
10Ø5
68
55
Kick Plate Installation
Description:
Once the stanchion has been
installed the kick plate is
secured with a riv nut no
more than 10mm from the
ground.
Fixings:
2 x Rivet 6 - 8.5 Ø5.1 304 SS
2 x WS10G22
M H 1 - W A L L M O U N T
M H 1 - 2 B A S E M O U N T
Description:
The kick plate, stanchion and
tubing is secured with a
singular wafer screw. In this
case a riv nut is not suitable.
Fixings:
4 x WS10G50.
Description:
To install kick plate onto a
MH1-4 Base Mount, a
connector should be secured
prior.
Fixings:
2 x Rivet 6 - 8.5 Ø5.1 304 SS
4 x WS10G50
M H 1 - 4 B A S E M O U N T
9 GRP-BR-03 Rev A
P R O D U C T C O D E P R O D U C T D E S C R I P T I O N I M A G E P R I C E
Flexible variable angle three way connector
Tubing
Kick Plate
Wall Mount
Rivets
Wafer Screws
TubingWall Mount
Kick Plate
Wafer Screws
Wafer Screw
TubingKick Plate Wafer Screw
Rivets
U connector
KICK PLATE INSTALLATION
V I S U A L G U I D E
GRP AUSTRALIA
T Y P I C A L H A N D R A I L A S S E M B LY
10 GRP-BR-03 Rev A
MH4-Connect
MH2-W Cross
MH1-4 Base
MH2-135º Elbow
MH1-Wall Mount
MH2-Flex
Kick Plate
M100 x 16 x 5
MH3-Flex + MH2-Flex
G R P A U S T R A L I A
L: 6 Hurricane Street, Banyo QLD
E: sales@grpaustralia.com.au
P: 0415 768 735
Recommended