View
3
Download
0
Category
Preview:
Citation preview
2016
Asher Enterprises
[HABITAT FOR HUMANITY]
Table of Contents Overview ....................................................................................................................................................... 3
General Overview ..................................................................................................................................... 3
Universal Design........................................................................................................................................ 3
Sustainable Features ................................................................................................................................. 3
New Construction Guidelines ....................................................................................................................... 4
Relevant Codes: ........................................................................................................................................ 4
Principle of Habitat: .................................................................................................................................. 4
Size of the House: ..................................................................................................................................... 4
Type of Construction – General: ............................................................................................................... 4
Accessibility: .............................................................................................................................................. 5
Energy Efficiency: ...................................................................................................................................... 5
Insulation: ................................................................................................................................................. 5
Doors and hardware: ................................................................................................................................ 5
Windows: .................................................................................................................................................. 6
Bathroom: ................................................................................................................................................. 6
HVAC, Washer/Dryer, & Plumbing:........................................................................................................... 6
Lighting: ..................................................................................................................................................... 6
Residential Code Requirements .................................................................................................................... 7
1. Light, Ventilation, and Heating ......................................................................................................... 7
2. Minimum Room Areas ...................................................................................................................... 7
3. Ceiling Height .................................................................................................................................... 9
4. Emergency Escape and Rescue Openings ......................................................................................... 9
5. Means of Egress ................................................................................................................................ 9
6. Stairways ......................................................................................................................................... 10
7. Ramps .............................................................................................................................................. 10
Plumbing Code Requirements .................................................................................................................... 11
WATER SUPPLY........................................................................................................................................ 11
DRAINAGE ............................................................................................................................................... 12
VENTS ...................................................................................................................................................... 13
Electrical Code Requirements ..................................................................................................................... 14
GENERAL ................................................................................................................................................. 14
RECPTACLE OULETS ................................................................................................................................. 14
GROUND-FAULT AND ARC-FAULT CIRCUIT-INTERRUPTER PROTECTION ............................................... 16
LIGHTING OUTLETS ................................................................................................................................. 16
Client Survey ............................................................................................................................................... 17
LEED Certification Process .......................................................................................................................... 18
....................................................................................................................... Error! Bookmark not defined.
Residential Water Supply ............................................................................................................................ 19
Water Supply Line Facts .......................................................................................................................... 19
Calculation: ............................................................................................................................................. 20
Wastewater Management .......................................................................................................................... 21
Calculations: ............................................................................................................................................ 21
Storm Water Runoff .................................................................................................................................... 22
Preconstruction ....................................................................................................................................... 22
Post Construction ....................................................................................... Error! Bookmark not defined.
Swale or Retention Pond Size: ................................................................... Error! Bookmark not defined.
Initial Sketches and Drawings ..................................................................................................................... 23
Revit Working Drawings .............................................................................................................................. 24
Title Page ................................................................................................................................................. 24
Original and Proposed Site Plan .............................................................................................................. 25
Furnished 1st Floor Plan .......................................................................................................................... 26
Dimensioned 1st Floor Plan ..................................................................................................................... 27
Front and Right Side Elevations .............................................................................................................. 28
Rear and Left Side Elevations .................................................................................................................. 29
Section Views .......................................................................................................................................... 30
Schedules ................................................................................................... Error! Bookmark not defined.
Electrical ..................................................................................................... Error! Bookmark not defined.
Plumbing .................................................................................................... Error! Bookmark not defined.
Picture Renderings .................................................................................................................................. 31
Overview
General Overview
The house that is being designed is for a Habitat for Humanity family. Habitat for humanity
International seeks to eliminate poverty housing and homelessness from the world and to make decent
shelter a matter of conscience and action. Through volunteer labor and donations of money
and materials, Habitat builds and rehabilitates simple, decent houses with the help of the homeowner
(partner) families. Habitat houses are sold to partner families at no profit and are financed with
affordable loans. The homeowners’ monthly mortgage payments are used to build additional Habitat
houses.
The land that the Habitat for Humanity house is on is fairly unique. The plot has two main roads along
with two alleys circling it. The Plot has a sidewalk on the two road sides. The Land is flat, well drained,
and is covered by sandy soil with some vegetation.
The house that is being created is being built with local and federal codes in mind, along with Habitat for
Humanity’s strict guidelines. There will be a three person family that will be moving into the house after
it is finished.
Universal Design
The design is largely influenced by the family that is moving in. They have certain Ideas that they would
like to see in their house. All the utilities and appliances are in the basement. Kitchen maneuverability,
door size, hallway size, and house size is very strictly governed by Habitat for Humanity.
Sustainable Features
This house was designed for a family home and will be part of the community for a long time. The
house is built with great materials, insulated so that heat loss is minimal. Blown insulation in the attic
utilizes recycled materials. The furnace and water heater are both energy star and highly efficient. The
water closets utilize water efficient materials like the toilet and faucets. The water use facilities and
appliances abide to LEED certification guidelines. Lighting will utilize florescent illumination for
additional energy savings.
New Construction Guidelines
Habitat for Humanity
These guidelines are subject to change and are presented for information only. These are subject to
building code requirements and are not considered specifications for any particular home.
Relevant Codes: Each house will conform to relevant codes and requirements of the city or
jurisdiction in which the house is built. This does not preclude a request for a variance if needed and
appropriate.
Principle of Habitat: Each house will conform in principle to the Habitat for Humanity standard of
simple and decent, deviating from that standard only as may be necessary. This means that HFH will
seek to avoid the “creeping affluence” that tends to increase amenities and cause prices of Habitat
houses to be inflated, and that the pre-unit costs of houses will be kept low to enable more families to
be served and more houses to be built.
Size of the House: The Board of Directors, upon recommendation of the Family Services
Committee and Construction Committee, will approve the size of the house. Sizes of houses shall not
exceed the following limits unless special circumstances, such as code requirements, warrant an
increase. Appropriate adjustments in size should be made if a basement is constructed due to the
impacts of a loss of square footage due to the addition of a stairwell and an increase in square footage if
the water heater and HVAC unit are relocated to the basement.
Two-bedroom – 900 square feet
Three-bedroom – 1070 square feet
Four-bedroom – 1233 square feet
Type of Construction – General: The following describes types of construction and
components that normally will be used; however, alternative types of construction may be considered,
depending on circumstances:
Crawl space (4 ft deep) is the preferred choice, although slab on grade construction or full or partial
basements (8 ft deep) may be required due to specific site conditions. The Construction Committee
will make this determination based on the site conditions. In crawl space construction, access into
the crawl space will be provided from the exterior through an access panel in the foundation wall.
The access panel will be a minimum of 36 inches wide by 24 inches high.
Where basements are required, access will be provided from the interior of the house. In addition,
an exterior access will be provided to meet egress requirements.
Foundation drainage shall be provided. Drainage of the system shall be by gravity flow if the site
allows it; by sump pump if the site requires it.
Exterior wood frame wall construction will consist of 2X6 fully sheathed with ½-inch foam board
insulation.
Exterior concrete wall construction will conform to the systems manufacturer’s recommendations
for concrete wall construction.
Roof construction shall consist of trusses @ 16-inch centers with 7/16 OSB rated panels.
Roof pitch shall be approximately 5/12 (optimized to minimize waste) with gable ends.
Houses will not include a basement, a garage, or a carport unless required by city code, other
restrictions, family health needs, or neighborhood considerations
Accessibility: The following describes accessibility provisions to be incorporated in houses. Houses
will be constructed to conform to standards of “minimal accessibility” or better as described in the
current version of the HFHI booklet Accessible Housing Manual: construction and Environmental
Resources. The requirements include:
An accessible entrance with no steps and a porch or overhang.
Passage doors, including the full bathroom, will be 36 in. wide. If necessary, secondary bathroom
doors may be 32 in. wide.
All hallways will be 42 in. minimum frame to frame.
Kitchen will be designed to permit wheel chair maneuverability (5 ft diameter open area).
Wall reinforcing for grab bars in bathrooms. If the family requires grab bars in the bathrooms at the
time of selection, they will be installed during the initial construction.
At least one full bathroom must be accessible (meet accessibility standards).
Energy Efficiency: Houses will incorporate energy conservation features, making them as energy
efficient as practicable. Features of ENERGY STAR energy efficient houses are considered a model to be
emulated, not a standard to be achieved at this time.
Insulation: The following describe insulation to be provided.
Wood frame construction shall include exterior walls insulated to at least an R-19 value using
fiberglass batt insulation and ½ inch insulation foam.
R-38 blown-in insulation shall be used in ceilings.
Crawl spaces will be conditioned spaces. Insulation is not required between floor joists. Foundation
walls will be insulated with 2 in. “blue board” foam insulation glued to the crawl space walls. The
crawl space shall have a 6-mil vapor retarder installed in contact with the ground.
If a basement is provided, the foundation walls will be insulated with 2 in. “blue board” foam
insulation glued to the walls. A vapor barrier will be installed under the floor slab.
Doors and hardware: The following describes doors and hardware to be provided.
Two steel clad entry insulated doors will be provided. Both doors will be 3 ft - 0 in. The primary
entrance door shall be a 6-panel door with half-moon light.
Attic access shall be provided.
Windows: The following describes windows to be provided.
All windows shall be white, vinyl, single hung, tilt-in, low e double pane.
Screens shall be integral with the windows.
Every bedroom will have at least one window and meet minimum egress requirements, as required
by code.
Kitchen/Dining room will have at least two windows or one double and one single window.
If a basement is provided, an egress window will be provided as required by the codes.
Bathroom: The following describes bathrooms to be provided.
A full bathroom must be accessible.
Two bedroom houses shall have one bathroom.
Three bedroom houses shall have 1-1/2 bathrooms.
Four bedroom houses (and larger) shall have 1-3/4 bathrooms.
A linen closet will be provided. A built-in linen closet will be used when possible if the floor plan
allows.
HVAC, Washer/Dryer, & Plumbing: The following describes heating, ventilation, and air
conditioning to be provided.
Electric heat pumps (14 SEER units) will be provided for the heating and cooling system.
A 40 gallon water heater shall be installed for a two bedroom house.
A 52 gallon water heater shall be installed for a three bedroom house.
An area shall be provided for installation of a clothes washer and dryer.
Two hose bibs shall be provided on the home exterior.
Lighting: The following describes lighting to be provided.
Ceiling light fixtures for incandescent light shall be provided in all rooms.
A single fluorescent, switched fixture shall be installed in each closet.
A light fixture shall be installed over the sinks in the bathroom and kitchen.
The porches or entrance areas shall have exterior light fixtures.
Residential Code Requirements
These code requirements are based on the 2009 International Residential Code (IRC) and represent a
small fraction of the requirements imposed by the IRC.
1. Light, Ventilation, and Heating
1.1 All habitable rooms must have a glazing area of at least 8 percent of the floor area of such rooms.
Natural ventilation shall be provided through windows, doors, louvers, or other approved openings to
the outdoor air with a minimum openable area of 4 percent of the floor area being ventilated.
1.2 Bathrooms, water closet compartments, and other similar rooms must have a glazing area in
windows of at least 3 square feet (0.3 m2), one-half of which must be openable.
Exception: Glazed areas are not required in rooms where artificial light and a mechanical ventilation
system are provided. Ventilation air shall be exhausted directly to the outside.
2. Minimum Room Areas
2.1 Every dwelling unit must have at least one habitable room that has a floor area of not less than 120
square feet (11m2).
2.2 Other habitable rooms (except kitchens) must have floor area of at least 70 square feet (6.5 m2).
2.3 Habitable rooms shall not be less than 7 feet (2134 mm) in any horizontal dimension.
Exception: Kitchens.
2.4 The clear opening in a kitchen must not be less than 5 feet.
Exception: In a galley kitchen in which there is a clear path through the room the minimum clear
opening is 3 feet 4 inches.
2.5 The minimum shower dimensions shall be 30 inches by 30 inches.
2.6 Bathroom fixtures shall be installed such that the minimum clearances shown in the figure below are
provided.
2.7 Portions of a room with a ceiling height of less than 7 feet (2134 mm) or with a sloping ceiling less
than 5 feet (1524 mm) from the finished floor to the finished ceiling cannot be considered as
contributing to the minimum required habitable area for that room.
3. Ceiling Height
3.1 Habitable spaces, hallways, bathrooms, toilet rooms, laundry rooms and portions of basements that
contain these types of spaces shall have a minimum ceiling height of 7 feet (2134mm).
Exceptions:
For rooms with sloped ceilings, at least 50 percent of the required floor area of the room must have a
ceiling height of at least 7 feet (2134 mm) and no portion of the required floor area may have a ceiling
height of less than 5 feet (1524 mm).
Bathrooms shall have a minimum ceiling height of 6 feet 8 inches (2032 mm).
4. Emergency Escape and Rescue Openings
4.1 Basements, habitable attics and every sleeping room shall have at least one operable emergency
escape and rescue opening (door, window or other openable devise). Emergency escape and rescue
openings must have a sill height of not more than 44 inches (1118 mm) above the floor.
4.2 All emergency escape and rescue openings must have a minimum net clear opening of 5.7 square
feet (0.530 m2). The clear opening area must be calculated using the position of the opening based on
normal operation from the inside.
Exception: Openings servicing a floor at grade may have a minimum net clear opening of 5 square feet
(0.465 m2).
4.3 The minimum net clear opening height must be 24 inches (610 mm). The minimum net clear opening
width must be 20 inches (508 mm).
5. Means of Egress
5.1 All dwellings shall have a safe means of egress. The means of egress shall provide a continuous and
unobstructed path of vertical and horizontal travel out of the building from all points within the dwelling
to the exterior at the required egress door without passing through a garage.
5.2 Each dwelling must have at least one egress door. The egress door shall be side-hinged, and shall
provide a minimum clear width of 32 inches (813 mm) when measured between the face of the door
and the stop, with the door open 90 degrees (1.57 rad). The minimum clear height of the door opening
shall not be less than 78 inches (1981 mm) measured from the top of the threshold to the bottom of the
stop. Other doors shall not be required to comply with these minimum dimensions.
5.3 There shall be a landing or floor on both side of each exterior door with a width not less than the
width of the door itself. Every landing must have a minimum dimension of 36 inches (914 mm) in the
direction of travel. Exterior landings may be sloped up to ¼ unit vertical in 12 units horizontal (2-
percent).
5.4 The minimum width of all hallways is 3 feet (914 mm).
6. Stairways
6.1 Stairways must have a clear width of 36 inches (914 mm).
6.2 The minimum headroom in all parts of the stairway shall not be less than 6 feet 8 inches (2032 mm).
6.3 The maximum riser height shall be 7 ¾ inches (196 mm), and the minimum tread depth shall be 10
inches.
6.4 There must be a floor or landing at the top and bottom of each stairway.
Exception: A floor or landing is not required at the top of an interior flight of stairs, provided a door does
not swing over the stairs.
7. Ramps
7.1 Ramps shall have a maximum slope of 1 unit vertical in 12 unites horizontal (8.3 percent slope
7.2 A minimum 3-foot-by-3-foot (914 mm by 914 mm) landing shall be provided:
At the top and bottom of ramps.
Where doors open onto ramps.
Where ramps change direction
Plumbing Code Requirements Requirements are based on the International Residential Code (IRC); however, local plumbing code requirements are generally much more detailed and cover many issues not addressed here. 1. General. The water supply and drainage system of a residence where plumbing fixtures are
installed must be connected to a public water supply or sewer system, respectively, where available. If a public water supply system or sewer system is not available, an individual water supply or private sewage disposal system, or both, shall be provided.
2. Freezing. When Water, soil or waste pipe is subject to temperatures below 32 degrees F, it must be protected from freezing by insulation or heat or both. Water service pipe shall be installed not less than 12 inches deep and shall be installed fully below the frost line.
3. Showers. Shower fixtures shall have at least 900 square inches of interior space and shall be not less than 30 inches in minimum dimension from the finished interior surface. Hinged shower doors shall open outward. The shower compartment must have an unobstructed access and egress opening with a minimum clear width of 22 inches.
4. Floor drains must not be installed under or have access limited by permanently installed appliances.
5. Hot water. Fixtures and faucets that have both hot and cold water supply shall be installed such that the hot water flow is controlled by the left-hand side of the water temperature control when facing the outlet.
6. Water Heaters. Each dwelling must have an approved automatic water heater.
WATER SUPPLY 7. Dwelling units shall be supplied with potable water. However, where nonpotable water is
distributed, the nonpotable system shall be identified by color marking or metal tags. If color is used, purple shall be used to identify municipally reclaimed water, rain water, and grey water distribution systems.
8. The water service distribution system shall provide capacities under peak demand at the point of outlet discharge not less than the following.
REQUIRED CAPACITIES AT POINT OF DISCHARGE
FIXTURE AT POINT OF OUTLET
FLOW RATE (gpm) FLOW PRESSURE (psi)
Bathtub 4 20
Dishwasher 2.75 8
Lavatory 4 8
Shower 3 20
Sink 2.5 8
Water closet, tank, one-piece
6 20
9. The maximum capacities for plumbing fixtures are shown below.
MAXIMUM FLOW RATES AND CONSUMPTION FOR PLUMBING FIXTURES AND FITTINGS
FIXTURE OR FITTING MAXIMUM CAPACITY
Lavatory faucet 2.2 gpm at 60 psi
Shower head 2.5 gpm at 80 psi
Sink faucet 2.2 gpm at 60 psi
Water closet 1.6 gallons per flushing cycle
10. Minimum pressure. Minimum static pressure at the building entrance shall be 40 psi. 11. Maximum pressure. Maximum static pressure shall be 80 psi. When main pressure exceeds 80
psi, a pressure-reducing valve shall be installed.
DRAINAGE 12. Dead ends are prohibited in drainage pipe except for cleanouts. 13. The size of the drainage pipe shall not reduce in the direction of flow. 14. Horizontal drainage pipe shall be installed to maintain a slope not less than ¼ inch vertical in 12
inches vertical (2 percent slope). 15. Drain pipe shall be sized based on the drainage fixture unit (d.f.u.) loads. 16. Drainage Fixture Units (d.f.u.) values for plumbing fixtures are given in the table below. DRAINAGE FIXTURE UNITS FOR FIXTURES
TYPE OF FIXTURE DRAINAGE FIXUTRE UNIT VALUE (d.f.u.)
Bathtub 2
Clothes washer 2
Dishwasher 2
Floor drain 0
Kitchen sink 2
Lavatory 1
Shower stall 2
Water closet 4
17. The building drain and sewer size and slope shall be determined from the table below based on
drainage load in fixture units (d.f.u.). No pipe providing drainage for a water closet shall be less than 3 inches in diameter.
MAXIMUM NUMBER OF FIXTURE UNITS ALLOWED TO BE CONNECTED TO BUILDING DRAIN OR BUILDING SEWER
No water closets included.
PIPE DIAMETER (in.) SLOPE PER FOOT
¼ inch ½ inch
2a 21 27
2 ½a 24 31
3 42 50
4 216 250
VENTS 18. In climates where the 97.5-percent value for outside temperature is 0 degrees F or lower, vent
pipes on installed on the exterior of the dwelling shall be protected from freezing by insulation, heat or both.
19. Open vent pipes that extend through the roof of the structure shall extend a minimum of 6 inches above the roof or 6 inches above the anticipated snow accumulations, whichever is greater. If the roof is used for anything other than protection from the weather (for instance equipment placement, a deck, etc.) the vent pipe must extend at least seven feet above the roof.
Electrical Code Requirements Requirements are based on the 2009 International Residential Code (IRC); however, local electrical code requirements are generally much more detailed and cover many issues not addressed here.
GENERAL One- and two-family dwellings shall be supplied by only one service.
RECPTACLE OULETS 1. Receptacle outlets shall be installed in every kitchen, family room, dining room, living room,
parlor, library, den, sun room, bedroom, recreation room, or similar room or area of dwelling units as specified below. a) Receptacles shall be installed so that no point measured horizontally along the floor line in
any wall space is more than 6 feet (1829mm) from a receptacle outlet.
b) A wall space shall include the following:
i. Any space that is 2 feet or more in width, including space measured around corners, and that is unbroken along the floor line by doorways, fireplaces, and similar openings.
ii. The space occupied by fixed panels in exterior walls, excluding sliding panels. iii. The space created by fixed room dividers such as railings and freestanding bar-type
counters. c) Receptacle outlets in floors shall not be counted as part of the required number of
receptacle outlets unless they are located within 18 inches of the wall. 2. In kitchens, pantries, breakfast rooms, dining rooms and similar areas of dwelling units a
receptacle outlet shall be installed at each wall countertop space 12 inches or wider. Receptacle outlets shall be installed so that no point along the wall line is more than 24 inches, measured horizontally from a receptacle outlet in that space. a) Exception: Receptacle outlets shall not be required on a wall directly behind a range,
counter-mounted cooking unit or sink. 3. At least one receptacle outlet shall be installed at each island countertop space with a long
dimension of 24 inches or greater and a short dimension of 12 inches or greater.
4. At least one receptacle outlet shall be installed at each peninsular countertop space with a long
dimension of 24 inches or greater and a short dimension of 12 inches or greater. A peninsular countertop is measured from the connecting edge.
5. Countertop spaces separated by range tops, refrigerators, or sinks shall be considered as separate countertop spaces.
6. Receptacle outlets shall be located not more than 20 inches above the countertop. Receptacle outlets shall not be installed in a face-up position in the work surfaces or countertops. a) Exception: Receptacle outlets shall be permitted to be mounted not more than 12 inches
below the countertop in construction designed for the physically impaired and for island and peninsular countertops where the countertop is flat across its entire surface and there are no means to mount a receptacle within 20 inches above the countertop, such as in an overhead cabinet. Receptacles mounted below the countertop in accordance with this exception shall not be located where the countertop extends more than 6 inches beyond its support base.
7. At least one wall receptacle outlet shall be installed in bathrooms and located within 36 inches of the outside edge of each lavatory. The receptacle outlet shall be located on a wall or partition that is adjacent to the lavatory basin location, or installed on the side or face of the basin cabinet not more than 12 inches below the countertop.
Receptacle outlets shall not be installed in a face-up position in the work surfaces or countertops in a bathroom basin location. 8. At least one receptacle outlet that is accessible while standing at grade level and located not
more than 6 feet, 6 inches above grade, shall be installed outdoors at the front and back of each dwelling unit having direct access to grade. Balconies, decks, and porches that are accessible from inside of the dwelling unit and that have a usable area of 20 square feet or greater shall have at least one receptacle outlet installed within the perimeter of the balcony, deck, or porch. The receptacle shall be located not more than 6 feet, 6 inches above the balcony, deck, or porch surface.
9. Hallways of 10 feet or more in length shall have at least one receptacle outlet. The hall length shall be considered the length measured along the centerline of the hall without passing through a doorway.
GROUND-FAULT AND ARC-FAULT CIRCUIT-INTERRUPTER PROTECTION 1. All receptacles installed in bathrooms shall have ground-fault circuit-interrupter protection
for personnel. 2. All receptacles installed in garages and grade-level portions of unfinished accessory
buildings used for storage or work areas shall have ground fault circuit-interrupter protection for personnel.
3. All receptacles installed outdoors shall have ground-fault circuit-interrupter protection for personnel.
4. All receptacles that serve kitchen countertop surfaces shall have ground-fault circuit-interrupter protection for personnel.
5. All receptacles that are located within 6 feet of the outside edge of a laundry, utility or wet bar sink shall have ground-fault circuit-interrupter protection for personnel. Receptacle outlets shall not be installed in a face-up position in the work surfaces or countertops.
LIGHTING OUTLETS 1. At least one wall switch-controlled lighting outlet shall be installed in every habitable room
and bathroom. a) Exceptions:
i. In other than kitchens and bathrooms, one or more receptacles controlled by a wall switch shall be considered equivalent to the required lighting outlet.
ii. Lighting outlets shall be permitted to be controlled by occupancy sensors that are in addition to wall switches, or that are located at a customary wall switch location and equipped with a manual override that will allow the sensor to function as a wall switch.
2. At least one wall-switch-controlled lighting outlet shall be installed in hallways, stairways, attached garages, and detached garages with electric power.
3. At least one wall-switch-controlled lighting outlet shall be installed to provide illumination on the exterior side of each outdoor egress door having grade level access, including outdoor egress doors for attached garages and detached garages with electric power. A vehicle door in a garage shall not be considered as an outdoor egress door.
4. Where one or more lighting outlets are installed for interior stairways, there shall be a wall switch at each floor level and landing level that includes an entryway to control the lighting outlets where the stairway between floor levels has six or more risers.
Client Survey
Family Information
Adult Names/Ages Kevin Winiarz/37 years old
Occupations Math Teacher
Child Names/Ages -
Child Names/Ages -
Physical Disabilities -
Other Special Needs -
Pets -
Architectural Details
House Style simple
Number of Bedrooms 2
Number of Bathrooms 1
Square Footage
Deck or Patio -
Extra Storage -
Leisure Activities
Hobbies
Entertainment
Equipment
Special Needs
Disabilities/illness -
Energy Saving/ LEED
Concepts and Ideas
Clean place
Site Development
Water Savings
Energy Efficiency
Materials Selection
Indoor Environmental
Quality
Other Ideas Minimalist; no clutter
LEED Certification Process
1. Innovative Process: I will meet with a bunch of experts to develop some ideas to make
the house greener.
2. Location and Transportation: The house will be located nearby multiple modes of
public transportation. There will also be a park nearby to allow for walking and biking.
3. Sustainable Site: The house will be built near many trees to allow for shade and
aesthetics. The house will have bioswales to route excess storm water away from where it
is not wanted.
4. Water Efficiency: There will be rain barrels so that there is minimal water waste.
5. Energy and Atmosphere: The house will be semi-powered by solar panels.
6. Materials and Resources: We will build the house using recycled materials, and any
leftover materials will be recycled. I will also talk to the contractor and discuss ways to
reduce site waste without changing any design aspects.
7. Indoor Environmental Quality: We will filter the air supply to make sure particles
aren’t continually recirculated. I will install and thermostat that uses sensors to make sure
the house is at the desired temperature. All doors will have weather stripping.
8. Innovation: I will meet with other engineers to come up with innovative solutions to
building issues.
9. Regional Priority: We will be aware of current environmental issues in the area and
ensure that we incorporate the surrounding environment into the plan.
Residential Water Supply
Water Supply Line Facts -The water line is 15 years old and is located at
184’-0” above sea level under 10th Street.
-The elevation at the lowest point of the tower’s
water cavity is 338.00 feet above sea level
-The pipe’s diameter is 8 in.
-The pipe’s length is 3.12 miles.
-The pipe is cast iron.
-The pipe has seven 90 degree flanged elbows
and one 45 degree flanged elbow.
-The pipe’s flow rate is 100 gpm.
Calculation:
Wastewater Management
Calculations:
Storm Water Runoff
Storm water runoff for the Habitat for Humanity site in Noblesville, IN
Explanation:
Site is flat, well drained, and is covered by sandy soil with some vegetation and has an
estimated runoff coefficient of 0.125. City code dictates a calculation for a 100-yr, 1-hr design
storm.
Preconstruction
Initial Sketches and Drawings
Revit Working Drawings Title Page
Original and Proposed Site Plan
Furnished 1st Floor Plan
Dimensioned 1st Floor Plan
Front and Right Side Elevations
Rear and Left Side Elevations
Section Views
Picture Renderings
kitchen
Laundry room
bathroom
bedroom
Living and dining room
Bookcase
Recommended