View
19
Download
0
Category
Preview:
Citation preview
Tous
dro
its d
e re
prod
uctio
n ré
serv
és p
our t
ous
pays
. Pho
tos
non
cont
ract
uelle
s
MECALAC FRANCE S.A.S. - Parc des Glaisins - 2 avenue du Pré de Challes F-74940 Annecy-le-Vieux - Tél. : +33 (0)4 50 64 01 63
Pelles / NOTE D’INFORMATION TECHNIQUE // NIT
INFORMATION - - INFORMATION - INFORMATION - INFORMATION - INFORMATION - INFORMATION - IN
1/2
Prise X01 714MWE
Concerne● Si vous êtes amenés à intervenir sur une 714MWe ou si la machine présente des dysfonctionnements sur des fonctions qui passent par la prise X01.● Exemples :- La jauge gasoil n’indique pas le bon niveau,- Perte de charge,- Calculateur absent.● Information simple, aucune garantie ne sera accordée.
Procédure1- Sous le plancher cabine, repérer la boucle du faisceau tourelle.2- Débrancher la prise X01.3- Défaire le collier Norma qui tient le faisceau.4- Tirer le faisceau vers l’extérieur.5- Couperlagaine(delaboucle)délicatementsanscouperlesfils sur environ 30 centimètres. Ceci pour enlever et éviter que de l’eau stagne.6- Soufflerpouréliminerunmaximumd’eau.7- Eventuellement utiliser une chaufferette pour sécher.8- Colsoner proprement le faisceau en laissant la gaine ouverte.9- Vérifierquelespinesduconnecteurnesontpasoxydées. Si non les nettoyer ou les remplacer.10- Remettre le faisceau dans le collier Norma.11- Rebrancher la prise X01.
DATE D’EDITION :31.07.2017
TYPE :714MWE
N° MACHINES CONCERNEES 81850
PRISE EN CHARGE MECALAC :
NON
RESPONSABLE : B. Ligot
I N F O R M A T I O N
Information simple, application des conditions normales de garantie.
N° Machine incluse
A partir de Jusqu’à
i
E.07.17.2017
MECALAC FRANCE S.A.S. - Parc des Glaisins - 2 avenue du Pré de Challes F-74940 Annecy-le-Vieux - Tél. : +33 (0)4 50 64 01 63
Pelles / NOTE D’INFORMATION TECHNIQUE // NIT
2/2
I N F O R M A T I O N
E.07.17.2017
Prise X01
Faisceau tourelle
Gaine à couper sur 30 cmCollier «Norma»
All
right
s of
repr
oduc
tion
rese
rved
in a
ll co
untri
es. N
on-c
ontra
ctua
l pho
togr
aphs
.
MECALAC FRANCE S.A.S. - Parc des Glaisins - 2 avenue du Pré de Challes F-74940 Annecy-le-Vieux - Tél. : +33 (0)4 50 64 01 63
Excavator / TECHNICAL INFORMATION NOTICE // TIN
1/2
Information only, the regular warranty conditions are applied.
Including N°machine
From To
INFORMATION - - INFORMATION - INFORMATION - INFORMATION - INFORMATION - INFORMATION - INI N F O R M A T I O N
i
E.07.17.2017
DATE OF ISSUE:31.07.2017
TYPE: 714MWE
TILL SERIAL NUMBER 81850
CREDITED: NO
ARRANGED BY: B. Ligot
Socket X01 714MWE
Concerne● If you have to work on a 714MWE or if the machine has faults on functions that go through socket X01.● Examples:- The diesel gauge does not show the right level,- Loss of head,- ECU absent.● Simple information, no guarantee will be granted.
Procédure1- Findtheloopoftheuppercarriageharnessunderthecabfloor.2- Disconnect socket X01.3- Undo the Norma collar which holds the harness.4- Pull the harness towards the outside.5- Cut the sheath (of the loop) delicately without cutting the wires over about 30 centimetres. This is for removing and preventing water from stagnating.6- Blow to remove as much water as possible.7- If necessary use a heater for drying.8- Use a “Colson collar” correctly on the harness leaving the sheath open.9- Check that the connector pins are not rusted. If not clean or replace them.10- Put the harness back in the Norma collar.11- Reconnect socket X01.
MECALAC FRANCE S.A.S. - Parc des Glaisins - 2 avenue du Pré de Challes F-74940 Annecy-le-Vieux - Tél. : +33 (0)4 50 64 01 63
Excavator / TECHNICAL INFORMATION NOTICE // TIN
2/2
I N F O R M A T I O N
E.07.17.2017
Socket X01
Upper carriage wiring harness
Sheath to be cut over 30 cm“Norma” collar
Ver
viel
fälti
gung
srec
hte
für a
lle L
ände
r vor
beha
lten.
Fot
os u
nver
bind
lich.
MECALAC FRANCE S.A.S. - Parc des Glaisins - 2 avenue du Pré de Challes F-74940 Annecy-le-Vieux - Tél. : +33 (0)4 50 64 01 63
Bagger / TECHNICAL INFORMATION // NIT
1/2
Zu Bekenntniss, die normalen Garantiebedinungen werden verwendet.
N° Mashine einbegriffen
Ab Bis
INFORMATION - - INFORMATION - INFORMATION - INFORMATION - INFORMATION - INFORMATION - IN
1/2
I N F O R M A T I O N
i
E.07.17.2017
AUSGABEDATUM:31.07.2017
TYP: 714MWE
BIS SERIENNUMMER 81850
ÜBERNAHME : Nein
BEARBEITER: B. Ligot
Anschlussdose X01 714MWE
Betrifft● Wenn Sie an einer 714MWE Eingriffe vornehmen müssen oder wenn die Maschine Störungen der Funktionen aufweist, die durch die Anschlussdose X01 gehen.● Beispiele:- Der Dieselmesser zeigt nicht den richtigen Stand an,- Ladungsverlust,- Steuergerät abwesend.● Bloße Information – es wird keine Garantie gegeben.
Vorgehensweise1- Unter dem Kabinenboden die Schleife des Oberwagen-Kabelbaums ausfindigmachen.2- Die Anschlussdose X01 lösen.3- Die Norma-Schelle lösen, mit der der Kabelbaum gehalten wird.4- Den Kabelbaum nach außen ziehen.5- Die Ummantelung (der Kabelbaumschleife) vorsichtig auf ungefähr 30 Zentimeter aufschneiden, ohne die Leiter zu durchtrennen, um Wasser zu beseitigen und zu vermeiden, dass es stagniert.6- Hineinblasen, um so viel Wasser wie möglich zu beseitigen.7- Eventuell einen Heizkörper zum Trocknen verwenden.8- Den Kabelbaum mit einem Kabelbinder bündeln und die Ummantelung offen lassen.9- Überprüfen, ob die Stifte des Anschlusses nicht verrostet sind. Sonst müssen sie gereinigt oder ausgetauscht werden.10- Den Kabelbaum wieder in der Norma-Schelle anbringen.11- Die Anschlussdose X01 wieder anschließen.
MECALAC FRANCE S.A.S. - Parc des Glaisins - 2 avenue du Pré de Challes F-74940 Annecy-le-Vieux - Tél. : +33 (0)4 50 64 01 63
Bagger / TECHNICAL INFORMATION // NIT
I N F O R M A T I O N
E.07.17.2017
2/2
Anschlussdose X01
Oberwagen-Kabelbaum
Ummantelung auf 30 cm aufschneiden„Norma“-Schelle
Tutti
i di
ritti
di ri
prod
uzio
ne ri
serv
ati p
er tu
tti i
paes
i. Fo
togr
afie
non
con
trattu
ali.
MECALAC FRANCE S.A.S. - Parc des Glaisins - 2 avenue du Pré de Challes F-74940 Annecy-le-Vieux - Tél. : +33 (0)4 50 64 01 63
Escavatori / NOTA INFORMATIVA TECNICA // NIT
1/2
Semplice informazione, applicazione delle normali condizioni di garanzia.
N° macchina incluso
A partire da Fino a
INFORMAZIONE - - INFORMAZIONE - INFORMAZIONE - INFORMAZIONE - INFORMAZION
1/2
INFORMAZIONE
i
E.07.17.2017
DATE DI EDIZIONE:31.07.2017
TIPO : 714MWE
N° MACCHINA 81850
A CARICO DI MECALAC:NO
RESPONSABILE : B. Ligot
Presa X01 714MWE
Concerne● Se è necessario intervenire su un modello 714MWE o se la macchina presenta dei malfunzionamenti su funzioni che passano dalla presa X01.● Esempi:- L’indicatore di livello del gasolio non indica il livello corretto,- Perdita di carico,- Computer assente.● Solo informazioni, non sarà accordata alcuna garanzia.
Procedura1- Sottoilpianaledellacabina,identificarel’anellodelcablaggiodellatorretta.2- Scollegare la presa X01.3- ToglierelafascettaNormachefissailcablaggio.4- Tirare il cablaggio verso l’esterno.5- Tagliarelaguaina(dell’anello)delicatamentesenzatagliareifili per circa 30 centimetri, per liberare ed evitare che l’acqua ristagni.6- Soffiarepereliminarel’acquaalmassimo.7- Eventualmente utilizzare un getto d’aria calda per asciugare.8- Fissare correttamente il cablaggio con una fascetta Colson lasciando la guaina aperta.9- Verificarecheglispinottidelconnettorenonsianoossidati. Altrimenti pulirli o sostituirli.10- Rimettere il cablaggio nella fascetta Norma.11- Ricollegare la presa X01.
MECALAC FRANCE S.A.S. - Parc des Glaisins - 2 avenue du Pré de Challes F-74940 Annecy-le-Vieux - Tél. : +33 (0)4 50 64 01 63
Escavatori / NOTA INFORMATIVA TECNICA // NIT
2/2
INFORMAZIONE
E.07.17.2017
Presa X01
Cablaggio torretta
Guaina da tagliare per una lunghezza di 30 cmFascetta «Norma»
Recommended