Introduction to Robotics i n CIM Systems Chapter 4 James A. Rehg Introduction to Robotics in CIM...

Introduction to RoboticsIntroduction to Roboticsiinn

CIM SystemsCIM Systems

Chapter 4Chapter 4

James A. RehgJames A. RehgIntroduction to Robotics in CIM Systems Introduction to Robotics in CIM Systems 55thth edition edition

Good Tooling DesignGood Tooling Design

Important CharacteristicsImportant CharacteristicsCapable of interacting with part(s)Capable of interacting with part(s)Sense presence of part in gripper(s)Sense presence of part in gripper(s)Weight minimized to maximize payloadWeight minimized to maximize payloadMaintain control of part(s) under acceleration Maintain control of part(s) under acceleration

& power loss& power loss

Ref Ch. 4-1 in bookRef Ch. 4-1 in book

Standard GrippersStandard Grippers

VariationsVariationsType of motionType of motionActuation methodActuation methodNormally open (NO) or closed (NC)Normally open (NO) or closed (NC)Surface GrippedSurface Gripped# of fingers# of fingers

Figure 4-1Figure 4-1

Figure 4-2 & 4-3Figure 4-2 & 4-3

Figure 4-9 & 10Figure 4-9 & 10

Figure 4-12 & 13Figure 4-12 & 13

Figure 4-16 & 17Figure 4-16 & 17

Figure 4-18 & 19Figure 4-18 & 19

Special Purpose ToolsSpecial Purpose Tools

DefinitionDefinitionDevices designed or modified to fit on the Devices designed or modified to fit on the end of a manipulator.end of a manipulator.

Criteria for useCriteria for useConsider for dirty, dangerous or dull jobs.Consider for dirty, dangerous or dull jobs.

Figure 4-25 & 26Figure 4-25 & 26

Figure 4-27 & 28Figure 4-27 & 28

Figure 4-32, 33 & 34Figure 4-32, 33 & 34

Introduction to Robotics i n CIM Systems Chapter 4 James A. Rehg Introduction to Robotics in CIM...

Documents

Cim-Tek Cross Reference - Allied ... - Allied ElectronicsFiltration PETROLEUM CROSS REFERENCE Cross Reference by Brand and Part Number Cim-Tek 70004 Cim-Tek 70059 Cim-Tek 70059 Cim-Tek

CIM Consignment Note Manual (GLV-CIM)

CIM SYSTEM ROBOTICS - ABB Group · · 2015-05-01CIM SYSTEM ROBOTICS ABB’S FIRST SYSTEM INTEGRATOR IN USA. ABB Flexible Automation. CIM SYSTEMS ... • Non-Technical Presentation

Computer Integrated Manufacturing and Robotics … · Web viewComputer Integrated Manufacturing (CIM) and Robotics Laboratory The CIM lab, located in D106, supports a wide range of

Yu-Ying Liu, James M. Rehg School of Interactive Computing, Georgia Institute of Technology

CIM Student Employment - TimesheetX CIM Supervisor Training

Chapter VIII - bpm-agu.com VIII A Reference Model for Industrial Enterprises ... CIM can connect the automation technologies of manufacturing processes, such as robotics

ROCHESTER CONFERENCE FOR SCHOOL · Web viewComputer Integrated Manufacturing (CIM): A Course in Automation and Robotics Applies principles of robotics and automation Builds on solid

Jon Rehg final 4 up writing digital mark photo port 2

Introduction to Industrial Electronics By James Rehg and Glenn Sartori Chapter 1

Computer Integrated Manufacturing (CIM) - Gunadarmaarief_nurdini.staff.gunadarma.ac.id/Downloads/files/64353... · Hardware CIM dan Software CIM CIM Hardware comprises the following:

CIM Digital Summit 2016 - CIM: Maria Heckel's Presentation

CIM 10-CIM11: workshop - Insurance medicine · CIM 10 –CIM 11 •Le diagnostic de fracture (CIM 10 – CIM 11), qui est anatomique peu précis, par rapport aux classifications AO

Introduction to Robotics i n CIM Systems Chapter 2 James A. Rehg Introduction to Robotics in CIM Systems 5 th edition

Aula 01 cim mix de cim

Uputstvo Za Popunjavanje Tovarnog Lista CIM GLV-CIM

PENDING CoSRGE OTHER BUSINESS · EXPERIMENTAL COURSE REPORT . None. CIM Considerations . CIM Forms CIM Processes CIM Help Bubbles . CHAIR’S AGENDA. Information Items Discussion

CIM/SMGS Consignment Note Manual (GLV-CIM/SMGS)

CIM ° » Û å>& L>' '¨9 ) M m ~)CIM ° » Û å>& L>' '¨9 ) M m ~) ... CIM

Handbuch CIM-Frachtbrief (GLV-CIM)