View
0
Download
0
Category
Preview:
Citation preview
KAT Pisystem Ioco AdapterOwner’s Manual
Thank you for purchasingthe KAT PiSystem Ioco Adapter.
Contact Information 12
First Use Instructions 10
FAQs 12
First and ForemostDeclarationSafety and Health Cautions
040506
Product Introduction
Product Description Product Parameters
0707
INDEX
Foreword
The owner’s manual contains all the information you need to install the KAT Pisystem Ioco Adapter. The following symbols are used to indicate crucial information and instructions for the set-up process:
First and Foremost
This symbol is a hint, letting you know what might be helpful at that particular point.
This symbol is important: you must complete one or more of installations or settings asdescribed in the manual.
This symbol is a safety warning to remind you to be wary of your personal safety whileperforming the task, be mindful of this symbol to avert any potential risks.
This symbol is a precaution: it usually provides additional information to help with a task, as well as information that applies only to certain situations.
04
Declaration
For the latest information, please feel free to check out our official website: http://www.katvr.com/
It is the trademark of Hangzhou Virtual and Reality Technology Co., Ltd. All trademarks, product identification and trade names of other companies appearing in this manual are owned by their respective owners. No parts or content of this manual may be copied or reproduced without the written permission of the company, and may not be shared in any form or used for any commercial or profitable purpose.
The contents of this manual are subject to change due to product upgrades or other reasons. Our company reserves the right to modify the contents of this manual without any notice or prompt. This manual is intended as a guide only. We do our best to provide accurate informa-tion in this manual, but we do not guarantee that the contents of the manual are completely error free. All statements, information, and recommendations in this manual do not constitute any warranty, express or implied.
05
This adapter is intended for use by people aged 14 to 60 years; if you do not meet the age requirement, please do not use it.
Please use this adapter according to proper instructions or under the guidance of a profes-sional to avoid damage. During its use by a minor, a guardian should always be present.
Choking hazard: Do not leave small components that pose a suffocation hazard to children or pets where they can reach.
Keep the adapter safely away from liquids or containers holding liquids.
Do not insert items into any openings on the adapter.
Do not place the adapter near fire or heat sources, nor try to leave it directly exposed to the sun.
Be sure to read and follow all product instructions and warnings related to your VR omni-directional platform and VR headset of choice.
If you violate the above cautions or carry out other violations, it may cause personal injury or adverse consequences, and KAT VR will not be responsible.
Those who use this adapter are considered to have full capacity of civil conduct and have complied with the aforementioned matters.
Safety and Health Cautions
To avoid injury or damage to the product, read and follow all installation and operation instructions before using the KAT PiSystem Ioco Adapter. If it is improperly used, potential risks may be triggered.
06
07
Product Introduction
Product Description
KAT PiSystem Ioco Adapter is a specialized adapter developed by KAT VR. It can synchronize the motion in the VR headset with the actual movement by its user.
Product Parameters
Adapter size
Adapter weight
Adapter power
USB ports
Micro USB cable
Mini USB cable
95*70mm
165g
2.5w
4 x USB 2.0 ports
5m
1m
Power cord spec
Work temperature
5V/2.5A
5V/2.5A
USB Ports
Power Port
PS4 Port mini USB Cable
microUSB Cable Power cord
21
08
Please finish the KAT loco pairing on KAT Gateway at your PC before using.
21
01
Take out a KAT PiSystem Ioco Adapter and three cables.
1
1
02
Locate the mini USB cable (PS4 connecting cable) labeled with the sticker “1” to connect the USB port as shown in the picture.
09
22
03
Locate the micro USB cable (controller cable) labeled with the sticker “2” to connect the USB port as shown in the picture.
04
And then connect the same micro USB label to Dualshock 4 controller.
06
Locate the power cord labeled with “switch” sticker and connect it to the power interface shown in the picture.
2
05
Locate and connect the USB cable to the base of KAT Ioco as shown in the picture.
First Use Instructions
2
1
07
complete the connection as shown in the picture.
10
01
Wait for one minute or two for the KAT PiSystem Ioco Adapter to start.
1-2 min
Controller connected.Who is using this controller?
Enter Options Menu
User1New User User1 User1
02
Before connecting the controller, make sure that the tower and the screen are both in operation and then press the PS button on Dualshock 4.
After pressing the button, the screen will show the above picture to indicate the success of adaption.
11
Left Ankle sensor Righ Ankle sensorWaist sensorReceiver
Please make sure controller cable is well connected and organized before and during playing VR game that requires controller. You may follow the same way of connecting the headset cable to deal with the controller cable.
If any controller or headset cable is twisted and twined before use, please manually unloose it, damage may be caused due to continuous twining.
And go back to STEP 6 for re-adaptation.
03
If adaption fails, unplug the power cord and wait for five seconds.
12
Q I’ve finished connecting all the cables but why doesn’t the button on the controller work?
Please press the PS button for adapting and pairing. If there is no response, please replug the power cord and restart the KAT PiSystem Ioco Adapter.
A
Q What should I do when the controller cable accidentally disconnects during gaming?
Reconnect the controller cable to KAT PiSystem Ioco Adapter and press the PS button for adapting. If there is no response, please replug the power cord and restart the KAT PiSystem Ioco Adapter.
A
Q What if the controller still doesn’t work after I restart PS4?
Every time you start PS4, please replug the power cord and restart the KAT PiSystem Ioco Adapter. A
There might be some non-scheduled updates for FAQs, please visit:http://katvr.com/knowledge.html#supportwz for more information.
FAQs
Contact Information
Company: Hangzhou Virtual and Reality Technology Co., Ltd
Room 901, Building 6, No 1818-2, West WenYi Road, Yuhang Street , Yuhang District, Hangzhou, Zhejiang Province, China.
Add:
Postal code: 311100
Tel: 400-826-0804
E-mail: info@katvr.com
Web: http://www.katvr.com/
Recommended