View
19
Download
0
Category
Preview:
Citation preview
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
Permanent Facility
1 CHEMICAL-METALLIC COATINGS& TREATMENTSOLUTIONS
Galvanized (Zinccoated steel wire)
Mass of Zinc Coating IS 6745 (RA 2016):1972
0.01 g/sq.m to 220g/sq.m
2 CHEMICAL-METALLIC COATINGS& TREATMENTSOLUTIONS
Galvanized (ZincCoated Steel Wire)
Mass of Zinc Coating ISO 1460: 1992 0.01 g/sq.m to 220g/sq.m
3 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Rope (3.00 to142.00mm of diameter)
Breaking Load IS 1608 - Part 1: 2018 Qualitative(0 to 8500kN)
4 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Rope (3.00 to142.00mm of diameter)
Breaking Load IS 9282(R2008): 2002 Qualitative(0 to 8500kN)
5 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Rope (3.00 to142.00mm of diameter)
Breaking Load ISO 6892: 2016 Qualitative(0 to 8500kN)
6 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Rope (3.00 to142.00mm of diameter)
Breaking Load EN 12385-1: 2008 Qualitative(0 to 8500kN)
7 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Rope (3.00 to142.00mm of diameter)
Breaking Load ISO 3108: 2017 Qualitative(0 to 8500kN)
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name USHA MARTIN LIMITED (WIRE AND WIRE ROPES DIVISION), TATISILWAI,RANCHI, JHARKHAND , INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5016 Page No. : 1 / 12
Validity 12/02/2019 to 11/02/2021 Last Amended on -
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
8 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Rope (3.00 to142.00mm of diameter)
Breaking Load IS 6594: 2001 Qualitative(0 to 8500kN)
9 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Rope (3.00 to142.00mm of diameter)
Breaking Load ISO 2408: 2004 Qualitative(0 to 8500kN)
10 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Rope (3.00 to142.00mm of diameter)
Diameter ISO 2408: 2004 Qualitative(3.00mm to160mm)
11 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Rope (3.00 to142.00mm of diameter)
Diameter EN 12385-1: 2008 Qualitative(3.00mm to160mm)
12 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Rope (3.00 to142.00mm of diameter)
Diameter IS 9282(R2008): 2002 Qualitative(3.00mm to160mm)
13 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Rope (3.00 to142.00mm of diameter)
Diameter ISO 2232: 1990 Qualitative(3.00mm to160mm)
14 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Rope (3.00 to142.00mm of diameter)
Diameter IS 6594: 2001 Qualitative(3.00mm to160mm)
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name USHA MARTIN LIMITED (WIRE AND WIRE ROPES DIVISION), TATISILWAI,RANCHI, JHARKHAND , INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5016 Page No. : 2 / 12
Validity 12/02/2019 to 11/02/2021 Last Amended on -
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
15 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Rope (3.00 to142.00mm of diameter)
Elongation % IS 6594: 2001 Qualitative(0 to 15%)
16 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Rope (3.00 to142.00mm of diameter)
Lay Length IS 9282(R2008): 2002 Qualitative(1mm to1500mm)
17 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Rope (3.00 to142.00mm of diameter)
Lay Length ISO 2408: 2004 Qualitative(1mm to1500mm)
18 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Breaking Load IS 14268(R2003): 1995 Qualitative(0 to 600 kN)
19 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Breaking Load AS/NZS 4672 (Part 1 &2): 2007
Qualitative(0 to 600 kN)
20 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Breaking Load BS 5896: 2012 Qualitative(0 to 600 kN)
21 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Breaking Load IS 6594: 2001 Qualitative(0 to 600 kN)
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name USHA MARTIN LIMITED (WIRE AND WIRE ROPES DIVISION), TATISILWAI,RANCHI, JHARKHAND , INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5016 Page No. : 3 / 12
Validity 12/02/2019 to 11/02/2021 Last Amended on -
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
22 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Breaking Load PrEN 10138-3: 2005 Qualitative(0 to 600 kN)
23 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Core Vs. Outer WireDifference (%)
AS/NZS 4672 (Part 1 &2): 2007
Qualitative(1to 5%)
24 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Core Vs. Outer WireDifference (%)
PrEN 10138-3: 2005 Qualitative(1 to 5%)
25 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Core Vs. Outer WireDifference (%)
BS 5896: 2012 Qualitative(1 to 5%)
26 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Diameter BS 5896: 2012 Qualitative(6.00mm to21.00mm)
27 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Diameter PrEN 10138-3: 2005 Qualitative(6.00mm to21.00mm)
28 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Diameter IS 14268: 2017 Qualitative(6.00mm to21.00mm)
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name USHA MARTIN LIMITED (WIRE AND WIRE ROPES DIVISION), TATISILWAI,RANCHI, JHARKHAND , INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5016 Page No. : 4 / 12
Validity 12/02/2019 to 11/02/2021 Last Amended on -
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
29 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Diameter IS 6594: 2001 Qualitative(6.00mm to21.00mm)
30 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Diameter AS/NZS 4672 (Part 1 &2): 2007
Qualitative(6.00mm to21.00mm)
31 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Elongation % AS/NZS 4672 (Part 1 &2): 2007
Qualitative(1 to 15%)
32 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Elongation % IS 14268: 2017 Qualitative(1 to 15%)
33 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Lay Length BS 5896: 2012 Qualitative(1mm to600mm)
34 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Lay Length IS 14268(R2003): 1995 Qualitative(1mm to600mm)
35 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Lay Length IS 9282(R2008): 2002 Qualitative(1mm to600mm)
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name USHA MARTIN LIMITED (WIRE AND WIRE ROPES DIVISION), TATISILWAI,RANCHI, JHARKHAND , INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5016 Page No. : 5 / 12
Validity 12/02/2019 to 11/02/2021 Last Amended on -
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
36 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Lay Length AS/NZS 4672(Part 1 &2): 2007
Qualitative(1mm to600mm)
37 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Load at 1% Elongation IS 14268(R2003): 1995 Qualitative(0 to 600 kN)
38 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Load at 1% Elongation AS/NZS 4672(Part 1&2): 2007
Qualitative(0 to 600 kN)
39 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Load at 1% Elongation PrEN 10138-3: 2005 Qualitative(0 to 600 kN)
40 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Metallic Area PrEN 10138-3: 2005 Qualitative(1 to 350 sq.mm)
41 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Metallic Area AS/NZS 4672 (Part 1 &2): 2007
Qualitative(1 to 350 sq.mm)
42 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Modulus of Elasticity(MOE)
IS 2854: 1990 Qualitative(1 to 300 kN/sq. mm)
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name USHA MARTIN LIMITED (WIRE AND WIRE ROPES DIVISION), TATISILWAI,RANCHI, JHARKHAND , INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5016 Page No. : 6 / 12
Validity 12/02/2019 to 11/02/2021 Last Amended on -
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
43 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Modulus of Elasticity(MOE)
AS/NZS 4672 (Part 1 &2): 2007
Qualitative(1 o 300 kN/sq. mm)
44 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Relaxation BS 5896: 2012 Qualitative(1to 500 kN)
45 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Relaxation IS 14268: 2017 Qualitative(1 to 500 kN)
46 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Relaxation PrEN 10138-3: 2005 Qualitative(1to 500 kN)
47 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Relaxation AS/NZS 4672 (Part 1 &2): 2007
Qualitative(1 to 500 kN)
48 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Tensile Proof load0.1%
IS 14268(R2003): 1995 Qualitative(0 to 600 kN)
49 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Tensile Proof Load0.1%
Pr.EN 10138-3: 2005 Qualitative(0 to 600 kN)
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name USHA MARTIN LIMITED (WIRE AND WIRE ROPES DIVISION), TATISILWAI,RANCHI, JHARKHAND , INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5016 Page No. : 7 / 12
Validity 12/02/2019 to 11/02/2021 Last Amended on -
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
50 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Tensile Proof Load0.1%
AS/NZS 4672(Part 1 &2): 2007
Qualitative(0 to 600 kN)
51 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Tensile Proof Load0.1%
BS 5896: 2012 Qualitative(0 to 600 kN)
52 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Tensile Proof Load0.2%
IS 14268(R2003): 1995 Qualitative(0 to 600 kN)
53 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Strand (6.00 to21.00mm of diameter)
Tensile Proof Load0.2%
AS/NZS 4672 (Part 1&2): 2007
Qualitative(0 to 600 kN)
54 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Wire (1.00 to 5.00mm of diameter)
Breaking Load IS 1608-Part1: 2018 Qualitative(0.5kN to50.0kN)
55 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Wire (1.00 to5.00mm of diameter)
Breaking Load IS 9282(R2008): 2002 Qualitative(0.5kN to50.0kN)
56 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Wire (1.00 to5.00mm of diameter)
Breaking Load BS 5896: 2012 Qualitative(0.5kN to50.0kN)
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name USHA MARTIN LIMITED (WIRE AND WIRE ROPES DIVISION), TATISILWAI,RANCHI, JHARKHAND , INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5016 Page No. : 8 / 12
Validity 12/02/2019 to 11/02/2021 Last Amended on -
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
57 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Wire (1.00 to5.00mm of diameter)
Breaking Load ISO 2232: 1990 Qualitative(0.5kN to50.0kN)
58 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Wire (1.00 to5.00mm of diameter)
Breaking Load EN 10264-1: 2002 Qualitative(0.5kN to50.0kN)
59 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Wire (1.00 to5.00mm of Diameter)
Breaking Load ISO 6892-1: 2016 Qualitative(0.5kN to50.0kN)
60 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Wire (1.00 to5.00mm of Diameter)
Diameter IS 9282(r2008): 2002 Qualitative(0.1mm to6.00mm)
61 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Wire (1.00 to5.00mm of Diameter)
Diameter IS 1608-Part 1: 2018 Qualitative(0.1mm to6.00mm)
62 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Wire (1.00 to5.00mm of Diameter)
Diameter ISO 6892-1: 2016 Qualitative(0.1mm to6.00mm)
63 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Wire (1.00 to5.00mm of Diameter)
Diameter EN 10264-1: 2002 Qualitative(0.1mm to6.00mm)
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name USHA MARTIN LIMITED (WIRE AND WIRE ROPES DIVISION), TATISILWAI,RANCHI, JHARKHAND , INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5016 Page No. : 9 / 12
Validity 12/02/2019 to 11/02/2021 Last Amended on -
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
64 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Wire (1.00 to5.00mm of Diameter)
Elongation % ISO 6892-1: 2016 Qualitative(1 to 15%)
65 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Wire (1.00 to5.00mm of Diameter)
Elongation % BS 5896: 2012 Qualitative(1 to 15%)
66 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Wire (1.00 to5.00mm of Diameter)
Elongation % IS 9282(R2008): 2002 Qualitative(1 to 15%)
67 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Wire (1.00 to5.00mm of Diameter)
Elongation % IS 1608-Part 1: 2018 Qualitative(1 to 15%)
68 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Wire (1.00 to5.00mm of Diameter)
Reverse Bend ISO 7801: 1984 Qualitative(bend radiisize 1.25, 1.75, 2.00,2.50, 3.00, 3.15, 3.25,3.45. 3.50, 3.75, 4.00,4.50, 5.00, 5.50, 5.75,6.00, 6.50, 7.00, 7.50,7.75, 8.00, 8.75, 9.00,9.25, 10.00, 10.50,11.00, 11.50, 12.50,14.00, 14.50, 15.00mm)
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name USHA MARTIN LIMITED (WIRE AND WIRE ROPES DIVISION), TATISILWAI,RANCHI, JHARKHAND , INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5016 Page No. : 10 / 12
Validity 12/02/2019 to 11/02/2021 Last Amended on -
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
69 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Wire (1.00 to5.00mm of Diameter)
Reverse Bend IS 1716(R2006): 1985 Qualitative(bend radiisize 1.25, 1.75, 2.00,2.50, 3.00, 3.15, 3.25,3.45. 3.50, 3.75, 4.00,4.50, 5.00, 5.50, 5.75,6.00, 6.50, 7.00, 7.50,7.75, 8.00, 8.75, 9.00,9.25, 10.00, 10.50,11.00, 11.50, 12.50,14.00, 14.50, 15.00mm)
70 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Wire (1.00 to5.00mm of Diameter)
Reverse Bend ISO 2232: 1990 Qualitative(bend radiisize 1.25, 1.75, 2.00,2.50, 3.00, 3.15, 3.25,3.45. 3.50, 3.75, 4.00,4.50, 5.00, 5.50, 5.75,6.00, 6.50, 7.00, 7.50,7.75, 8.00, 8.75, 9.00,9.25, 10.00, 10.50,11.00, 11.50, 12.50,14.00, 14.50, 15.00mm)
71 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Wire (1.00 to5.00mm of Diameter)
Reverse Bend EN 10218-1: 2012 Qualitative(bend radiisize 1.25, 1.75, 2.00,2.50, 3.00, 3.15, 3.25,3.45. 3.50, 3.75, 4.00,4.50, 5.00, 5.50, 5.75,6.00, 6.50, 7.00, 7.50,7.75, 8.00, 8.75, 9.00,9.25, 10.00, 10.50,11.00, 11.50, 12.50,14.00, 14.50, 15.00mm)
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name USHA MARTIN LIMITED (WIRE AND WIRE ROPES DIVISION), TATISILWAI,RANCHI, JHARKHAND , INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5016 Page No. : 11 / 12
Validity 12/02/2019 to 11/02/2021 Last Amended on -
S.No Discipline / Group Product / Material ofTest
Specific TestPerformed
Test MethodSpecificationagainst which testsare performed
Range of Testing/Limits of Detection
72 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Wire (1.00 to5.00mm of Diameter)
Reverse Bend BS 5896: 2012 Qualitative(bend radiisize 1.25, 1.75, 2.00,2.50, 3.00, 3.15, 3.25,3.45. 3.50, 3.75, 4.00,4.50, 5.00, 5.50, 5.75,6.00, 6.50, 7.00, 7.50,7.75, 8.00, 8.75, 9.00,9.25, 10.00, 10.50,11.00, 11.50, 12.50,14.00, 14.50, 15.00mm)
73 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Wire (1.00 to5.00mm of Diameter)
Torsion ISO 2232: 1990 Qualitative
74 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Wire (1.00 to5.00mm of Diameter)
Torsion ISO 7800: 2012 Qualitative
75 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Wire (1.00 to5.00mm of Diameter)
Torsion EN 10218-1: 2012 Qualitative
76 MECHANICAL-MECHANICALPROPERTIES OFMETALS
Steel Wire (1.00 to5.00mm of Diameter)
Torsion IS 1717: 2018 Qualitative
This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name USHA MARTIN LIMITED (WIRE AND WIRE ROPES DIVISION), TATISILWAI,RANCHI, JHARKHAND , INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-5016 Page No. : 12 / 12
Validity 12/02/2019 to 11/02/2021 Last Amended on -
Recommended