View
1
Download
0
Category
Preview:
Citation preview
Lava™ Furnace 200
More output.Faster sintering.
Sinter more units with the Lava™ Furnace 200Increase the output of your lab with the new 3M™ ESPE™ Lava™
Furnace 200 by reducing sintering times and producing more
units per sintering cycle. 3M ESPE worked with DEkEMA
to customize the newly-developed AUSTrOMAT® µSiC® high-
temperature furnace for Lava™ Zirconia. This means that you’ll
now get a furnace from one of the most innovative manufacturers,
adapted specifically for Lava™ Copings and Frameworks.
This furnace features software for telediagnosis, so that it
may be serviced remotely by 3M ESPE personnel. The heating
elements are distinguished by their extraordinary long operating
life. Installation is simple, since the furnace automatically adjusts
to the supplied voltage.
Shorter sintering cycles
Three programs give you the flexibility to reduce oven time —all
three programs are faster than the Lava™ Therm Furnace.
Increase productivity Because you can sinter more units in each cycle and increase
the number of cycles per day, you can dramatically increase
your daily output.
Consume less energy Now you can do more with less. You can produce additional units
with each sintering cycle. For the higher capacity, you can save
on time, costs and wattage.
60
80
100
0
20
40
120
140
160Daily Capacity
Units
Lava™ Furnace 200 (2 cycles)
70
70
Lava™ Therm (1 cycle)
40
Internal 3M ESPE data. Capacity per cycle and cycles per day of the Lava™ Furnace 200 vs. the Lava™ Therm Furnace.
6
8
10
0
2
4
Average Power Consumption
KWh
Lava™ Furnace 200
6.4
Lava™ Therm
8.2
Internal 3M ESPE test data. Average energy expended to complete the test cycle.
6.0
8.0
10.0
0
2.0
4.0
12.0
14.0Sintering Time
Hour
s
Lava™ Therm
13 hours 30 min.
Lava™ Classic
8 hours30 min.
Lava™ Pre-dried
5 hours
Lava™ Non-shaded
4 hours 48 min.
Internal 3M ESPE data. Sintering time for the Lava™ Furnace 200 programs vs. the sintering program for the Lava™ Therm Furnace.
PrecisionSolutionsUse custom sintering programs for Lava™ Zirconia
Lava zirconia is formulated and processed with a methodology that is a trade
secret. Sintering is a critical step to the final material properties. By using the
custom sintering programs for Lava zirconia, you can ensure your authentic
coping and frameworks have a similar translucency to natural dentin.
Track your cases—up to 12 sub-sections
Sintered crowns and bridges can look similar. In order to easily identify
your cases, record the placement of each case on the log sheet
provided in the Lava™ Furnace 200 Sintering Guide.
Use specially-designed accessories The Lava furnace comes with 3M ESPE’s custom-designed accessories.
Each of these items can also be ordered separately.
Sintering CruciblesThe sintering crucibles are made of customized Alumina (Al
2O
3)
and designed in two parts—a ring and a plate. The starter kit
contains four plates and three rings.
Tray Gripper ToolThe stainless steel gripper is specially-
designed by 3M ESPE for safe handling
of hot sinter trays. One gripper tool is
included in the starter kit.
Honeycomb Sintering CarrierManufactured with build-up technology, the honeycomb
sintering carrier is separated into numbered quadrants.
Lava™ restorations can be tracked for easy identification
when you use the log sheet. The starter kit contains three
honeycomb sintering carriers.
Each starter kit comes with three crucibles, one gripper tool and three honeycomb sintering carriers. All items are also sold separately. Please refer to the back page for order numbers.
3M ESPE Customer Care Center at 1-800-634-2249 3MESPE.com/lava
3M CanadaPost Office Box 5757London, Ontario N6A 4T1Canada1-888-363-36853MESPE.ca/lava
Dental Products3M CenterBuilding 275-2SE-03St. Paul, MN 55144-1000USA
3M, ESPE and Lava are trademarks of 3M or 3M ESPE AG. Used under license in Canada.DEkEMA, Austromat and µSiC are trademarks of DEkEMA Dental-keramiköfen GmbH.
Please recycle. Printed in USA.© 3M 2008. All rights reserved.70-2013-0129-1
Technical DataDimensions 42 x 98 x 60 cm (width x height x depth)
Weight 75 kg
Heating elements 3 long-life SiC heating elements
Control unit USB wired control unit with plain text menu
Firing temperature range 50°C to 1600°C
Supply voltage Furnace automatically adjusts to supplied voltage
Connectivity USB port and Ethernet port
Control unit for easy operationArrange your workspace to fit your needs. The
control unit can either be wall mounted or placed
on a table. In addition, the convenient display
indicates the remaining cycle time. 3M™ ESPE™ Lava™ Furnace 200 Control UnitThe plain text menu is easy to read.
Accessories Ordering InformationItem # Product Information
68796 Tray Gripper Tool The stainless steel gripper is made for safe handling of hot sinter trays.
68797 Plate The plate is the bottom piece of the sintering crucible.
68791 Ring The ring is the outer wall of the sintering crucible.
68799 Honeycomb Sintering Carrier The tray is placed in the sintering crucible and holds restorations. The numbered quadrants help technicians track cases.
68896
Sintering Aids Pegs, soft wires and swings are used to hold copings and frameworks on the honeycomb sintering carrier. To accommodate the proper shrinkage of the zirconia that occurs during sintering, please refer to the Lava™ Frame Zirconia Instructions for Use on which sintering aid to use for various indications.
Sintering Pegs 25mm 25 pieces
68897 Sintering Pegs 33mm 10 pieces
68898 Soft Wires 6 pieces
68899 Swings 4 pieces
69912 Soft Wires for Bridges 6 pieces
69913 Insulated Furnace Table The insulated furnace table securely holds the sintering crucibles on the Lava™ Furnace 200.
a
b
c
d
e
f
g
h
i
j
ab
c d
e f g h i
j
Recommended