Loopstar 714 and Loopstar 718

LoopStar® 714 and LoopStar® 718 Extend Ethernet Services to All Customers Over Readily Available T1/E1 Facilities

We all hear about the glut of fiber in the ground today. Unfortunately not much of it really exists in the lastmile. T1s and E1s are still the primary mode of transport for a majority of locations. So how do you provideeconomical business-class Ethernet services to your off-net customer locations that can only be reachedthrough T1s or E1s? How do you offer Ethernet bandwidth and cost savings to customers who thought theycould only get Frame Relay service, speeds and pricing?

The LoopStar714 and LoopStar718 are tailored to help service providers reach their off-net customers andreduce service fees at the same time. The LoopStar714 offers highly manageable 10/100 customer access andup to four T1/E1s (eight T1/E1s for the LoopStar718) for the network connection. These T1/E1s are bondedusing the standard Multilink Point-to-Point Protocol (MLPPP), offering up to 12 Mb/s (T1) or 16 Mb/s (E1) ofservice. Additional lines can be added as necessary, and with a simple-to-use Graphical User Interface (GUI),provisioning new circuits has never been easier. And the LoopStar products come equipped with LoopStar700intelligent management, designed to support remote service provisioning, verification, and troubleshooting.From RMON counters and Ethernet / WAN loopbacks to a built-in Ethernet port Time Domain Reflectometry(TDR) test, from complete Layer 2+ classification and service definition to link quality monitoring andreporting, the LoopStar714 and LoopStar718 provide the flexibility and scalability to deliver customer-specific solutions and support with pinpoint accuracy.

Flexible and Differentiated Ethernet SolutionsOffering business-class Ethernet services by providing strong Class of Service (CoS) features, theLoopStar714 and LoopStar718 can be used for:

• Point-to-point and hub-and-spoke deployments

• Full range of 4,096 Virtual LANs

• Layer 2 Virtual Private Networks (VPNs)

• Traffic prioritization and classification

For example, with the advanced traffic classification features of the LoopStar714 and LoopStar718, Voice overIP (VoIP) traffic can be given priority over Internet access traffic. The LoopStar products support up to 10 rule-based classifications based on any of the following inputs: VLAN ID, VLAN P-bits, ToS bits and DiffServ CodePoints. In addition to this classification scheme, rate limiting and policing are also provided to round out a fullsuite of tools for customer provisioning and service.

SPEC

SH

EET

SP

EC S

HEE

T

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 • 1 - 8 0 0 - 3 6 6 - 3 8 9 1

Features• Multilink Point-to-Point Protocol (MLPPP)

• ‘Plug-and-play’ platform and design

• LoopStar700 Intelligent Management Capabilities

• LoopStar700 Traffic Management

• LoopStar700 Performance and Fault Management

01

/0

6

•

10

21

57

AE

Lo

op

Star

®7

14

an

d L

oo

pSt

ar®

71

8

LoopStar® 714 and LoopStar® 718 Extend Ethernet Services to All Customers Over Readily Available T1/E1 Facilities

2w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 • 1 - 8 0 0 - 3 6 6 - 3 8 9 1

Benefits• Cost-effective approach to deliver Ethernet services over NxT1 and NxE1

• ‘Plug-and-Play’ design for easy installation, configuration and management

• Proven management software with comprehensive and robust features

• Standard MLPPP bonding means T1/E1s can be added as customer bandwidth needs grow

• Simple replacement for Frame Relay services

• Bond from 1-8 T1/Es to provide bandwidth ranging from 1.5 Mb/s to 16 Mb/s; automatic removal / restoration of failed links

• Compact design makes it simple to install at the customer premise, either as a wall-mounted orrack-mounted unit

• Allow for easy access to configure or disable access and ports from anywhere; secure in-band management access from anywhere on the network

• Customer traffic classification, supporting up to 10 traffic rules per device, as well as VLAN management, traffic queuing, rate limiting and policing

• Support for both Layer 1 and Layer 2 performance monitoring statistics, as well as facility alarms available over both the in-band management channel and the local management console port

• Built-in loopbacks and a built-in Ethernet port Time Domain Reflectometer keep service calls to a minimum

Easy Fit into Existing OAM&P InfrastructureIn conjunction with the LoopStar700 suite’s in-band management VLAN channel, robust GUI and full SNMPconnectivity, the LoopStar714 and LoopStar718 are easy to configure, manage and monitor. Performancemonitoring is supported for both the T1/E1 and Ethernet interfaces. Fault management is covered through the useof equipment and facility alarms available over both the in-band management channel and through the localmanagement console port. The LoopStar714 and LoopStar718 provide a strong set of carrier operational supporttools, which extend beyond standard T1/E1 loopback testing and reach all the way to the user-facing Ethernet port.

The LoopStar714 and LoopStar718 complement the LoopStar700 product line, enabling service providers to createnew business service revenues by delivering high-margin Ethernet services to all of their customers, no matter wherethey are located on the network.

Bonded T1/E1s

T1/E1 Ethernet

Switch/Router

Ethernet

VoIP PBX

Core

LS750

LS714

LS718

The LoopStar714 and LoopStar718 offer business-class Ethernet to any size location.

01

/0

6

•

10

21

57

AE

Lo

op

Star

®7

14

an

d L

oo

pSt

ar®

71

8

LoopStar® 714 and LoopStar® 718 Extend Ethernet Services to All Customers Over Readily Available T1/E1 Facilities

3w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 • 1 - 8 0 0 - 3 6 6 - 3 8 9 1

Specifications

Interfaces: 1 x 10/100Base-T port1 x 100Base-FX (SM or MM SFP) 8 x T1/E1 interfaces, supports 1 MLPPP bundle (LoopStar 718)4 x T1/E1 interfaces, supports 1 MLPPP bundle (LoopStar 714)1 x 10/100 management port

Maintenance: T1/E1 loopbacks and PMEthernet loopbacks and PMEthernet cable testing with TDR

WAN Protocol: RFC1661: Point-to-Point Protocol (PPP) and Link Control Protocol (LCP)RFC1990: PPP Multilink Protocol (ML-PPP)RFC3518: Bridging Control Protocol (BCP)Automatic removal/restoration of failed links

Ethernet Services: 802.1p prioritization802.1Q VLAN tagging/switching/stackingRate limiting: 128-500 kb/s incrementsCoS: WRR or strict priority based on VLAN, p-bits or ToS/DSCP

Management: IP host with DHCP client for automatic address assignmentIn-band management VLANWeb-based management interface (GUI)SNMP agent supporting standard MIBs, including RMONFTP client for downloadLoopStar 700 intelligent management

Power Options: AC Power: 100-240 V auto ranging, 47-63HzDC Power: Dual DC Feeds -48 VDC nominal (-40 to -60 VDC) or 24 VDC

Physical: 1 RU (1.75" x 17" x 7.25")Wall-mount or rack-mount (19" and 23")Full front access (ETSI form factor)Temperature hardened (option)-40° to +65° C (operating)-40° to +70° C (storage)

Regulatory: UL ListedEN/UL 60950CE MarkFCC Part 15 Class BNEBS Level 3 certified

ADC Telecommunications, Inc., P.O. Box 1101, Minneapolis, Minnesota USA 55440-1101Specifications published here are current as of the date of publication of this document. Because we are continuouslyimproving our products, ADC reserves the right to change specifications without prior notice. At any time, youmay verify product specifications by contacting our headquarters office in Minneapolis. ADC Telecommunications,Inc. views its patent portfolio as an important corporate asset and vigorously enforces its patents. Products orfeatures contained herein may be covered by one or more U.S. or foreign patents. An Equal Opportunity Employer

102154AE 1/06 Original © 2006 ADC Telecommunications, Inc. All Rights Reserved

Web Site: www.adc.comFrom North America, Call Toll Free: 1-800-366-3891 • Outside of North America: +1-952-938-8080 Fax: +1-952-917-3237 • For a listing of ADC’s global sales office locations, please refer to our web site.

SPEC

SH

EET

O r d e r i n g I n f o r m a t i o n

Description Catalog Number

LPS-714 AC Package (1 10/100, 1FX, no optics, 4-T1/E1)*Includes: 1 AC power supply and AC power cord, 19” and 23” LPS-714-AC L1rack mount brackets, license for basic software and documentation

LPS-714 DC Package, Temperature Hardened (1 10/100BT, 1FX, no optics,4-T1/E1) *Includes: Internal dual feed - 48Vdc power supply, 19” and 23” LPS-714-48DC L1rack mount brackets, license for basic software and documentation

LPS-714 24DC Package, Temperature Hardened (1 10/100BT, 1FX, no optics,4-T1/E1) *Includes: Internal dual feed - 24Vdc power supply, 19” and 23” LPS-714-24DC L1rack mount brackets, license for basic software and documentation

LPS-718 AC Package, (1 10/100BT, 1FX, no optics, 8-T1/E1)*Includes: 1 AC power supply and AC power cord, 19” and 23” LPS-718-AC L1rack mount brackets, license for basic software and documentation

LPS-718 48VDC Temperature Hardened, (1 10/100BT, 1FX, no optics, 8-T1/E1)*Includes: Internal dual feed -48dc power supply, 19” and 23” LPS-718-48DC L1rack mount brackets, license for basic software and documentation

LPS-718 24DC Temperature Hardened, (1 10/100BT, 1FX, no optics, 8-T1/E1)*Includes: Internal dual feed -24Vdc power supply, 19” and 23” LPS-718-24DC L1rack mount brackets, license for basic software and documentation