View
18
Download
0
Category
Preview:
Citation preview
LTT SeriesTorque, Angle & Force Analyzer with ARCII Technology
TorqueLab
LTT
01.1
TorqueAnalyzers
Recommended for all hand screwdrivers, wrenches, or power tools.
KEY FEATURES
Features a built-in transducer and can connect to an external torque sensor.
LTT10i
LTT25i
LTT50i
LTT100i
LTT250i
LTT50F
LTT100F
LTT250F
Torque RangesItem #
11.3 - 113 cN.m
28.25 - 282.5 cN.m
56.5 - 565 cN.m
113 - 1130 cN.m
282.5 - 2825 cN.m
6.8 - 67.8 N.m
13.56 - 135.6 N.m
33.9 - 339 N.m
S.I.
1 - 10 lbf.in
2.5 - 25 lbf.in
5 - 50 lbf.in
10 - 100 lbf.in
25 - 250 lbf.in
5 - 50 lbf.ft
10 - 100 lbf.ft
25 - 250 lbf.ft
AmericanModel
068400
068401
068402
068403
068404
068405
068406
068407
1.2 - 11.5 kgf.cm
2.9 - 28.8 kgf.cm
5.8 - 57.6 kgf.cm
11.5 - 115 kgf.cm
28.8 - 288 kgf.cm
0.7 - 6.9 kgf.m
1.4 - 13.8 kgf.m
3.5 - 34.5 kgf.m
1/4" F/Sq
1/4" F/Sq
1/4" F/Sq
1/4" F/Sq
1/4" F/Sq
3/8" F/Sq
1/2" F/Sq
1/2" F/Sq
Drive Size
8 lbs.
8 lbs.
8 lbs.
8 lbs.
8 lbs.
8 lbs.
8 lbs.
8 lbs.
Wt.Metric
NOTE!Since a tester cannot always duplicate actual jointcharacteristics, the torque reading displayed on the LTT mayvary from the actual torque that a tool will apply to a joint.When critical assemblies are involved, the torque output of thepower tool being used should be verified on the actualassembly using a calibrated measuring torque tool.
Selection of six operation modes:Track, Peak, First Peak, Audit, Spindle Audit, and Torque + Angle
Seven units of torque measurements:ozf.in, lbf.in, lbf.ft, cN.m, N.m, kgf.m, kgf.cm
Two units of force measurement: lbf and kN
Features built-in Tool Tests operation.
Three PC Windows based software programs: Mountz Torque Meter Interface Program for sensor calibrations, meter calibration and tool tests. Torque Meter Bootloader for updating the LTT operating systems. Excel Add-In for Real-Time data collection into an Excel spreadsheet. It provides statistics calculations.
Five low-pass filters: 3000, 2000, 1500, 500, and 200Hz
Six-digit display and easy to read menu structure.
Real Time Clock for time stamping of readings.
USB interface to download readings to PC.
High Capacity Li-ion Batteries for long life (30 hours with standard torquesensors and 16 hours with brushless rotary sensors).
Can connect to most mv/v sensors and can store calibration data for up to50 non-smart torque sensors.
The 5VDC capability allows unit to be used with a brushless rotary torquesensor for testing pulse tools and high RPM tools.
Features Go / No Go LEDs that illuminate when high or low setting isachieved.
Real time graph of torque vs. time using associated PC Windows software.
Stores a total of 5000 data points.
Torque and Angle data is displayed simultaneously when used with torqueand angle sensors, up to 8000 RPM for angle measurement.
Torque Sensor
RTSX-A
All BLRTSX models
BMX
MTX
SDX
RTSX
CABLE CHART
072000
072001
072002
072003
072004
072005
Item #
Accuracy 0.5% of reading from 20% to 100% of full scale.Accuracy 1% of reading from 10% to 20% of full scale.
Provides EZ-Plug & Play with Mountz torque sensors. Features ARCIItechnology, an instant auto-recognition system of the sensors connected tothe LTT.
Flash memory allows upgrades to be done by the user in the field &internet through the USB port.
Item #
072998
072997
ACCESSORIESOPTIONAL
Multiplexer
Bar Code Reader
Description
Mounting Bracket(for LTT model 10i-50F)
072608
Mounting Bracket(for all LTT models)
072606
ACCESSORIESINCLUDED
USB Cable
Run Down Adapter
Mountz Software Progams
Battery Pack
Description
770301
770319
See Pg. 01.16
-
072506
Item #
Universal Charger(100-240VAC)
800.456.1828
PLUG & PLAYSupplied with Free ISO 17025Certification of Calibration.
CERTIFIED
EZ-TorQ IITorque Analyzer
TorqueAnalyzers
SPRING RUN DOWNADAPTERS
Provides consistent andreliable torque readings foruse with power driven torquecontrol tools.
See Page 01.13
EZ-TorQ
01.2
Recommended for hand screwdrivers, most wrenches andpower tools (Not for use in testing Impact or Pulse type tools).
KEY FEATURES
EZ-TorQ II 10i
EZ-TorQ II 50i
EZ-TorQ II 100i
EZ-TorQ II 150i
Torque Ranges
11.3 - 113
56.5 - 565
113 - 1130
169.5 - 1695
cN.m
1 - 10
5 - 50
10 - 100
15 - 150
lbf.inModel
1.2 - 11.5
5.8 - 57.6
11.5 - 115
17.3 - 173
Item #
070800
070801
070802
070803
17mm Female/Hex*
17mm Female/Hex*
17mm Female/Hex*
17mm Female/Hex*
Drive Size
4.5 lbs.
4.5 lbs.
4.5 lbs.
4.5 lbs.
Weightkgf.cm
* Each model includes a 1/4" Female/Hex Sq. Drive Adapter and a Spring Run Down Adapter for testing power tools.
CALIBRATION TESTEQUIPMENT
Calibrated Dead Weight andlength are the official meansby which Analyzers aretraced to NIST, ISO etc.
See Page 01.12
NOTE!Since a tester cannot always duplicate actual jointcharacteristics, the torque reading displayed onthe EZ-TorQ may vary from the actual torque thata tool will apply to a joint. A run down adapterthat simulates a variety of different jointcharacteristics is provided with the EZ-TorQ.When critical assemblies are involved, the torqueoutput of the power tool being used should beverified on the actual assembly using a calibratedmeasuring torque tool.
600728-1*
600728-2*
600728-3*
600728-4*
600734-18*
600734-20*
Item #
SCREW RUN DOWN ADAPTERS
RDA
RDA
RDA
RDA
RDA
RDA
Model
2 - 56
4 - 40
6 - 32
8 - 32
5/16 - 18
1/4 - 20
American
M2x.4
M3x.5
M4x.7
M5x.8
-
-
Metric
5
5
5
5
5
5
Quantity
* Hardware Kit # 1 for these RDA units (includes Washer and Screws), Item # 061237.
See EZ-TorQ manual for a list of items that areincluded in the Hardware Kit.
ACCESSORIES OPTIONAL
Accuracy 0.5% of reading from 20% to 100%Accuracy 1% of reading from 10% to 20%
Dimensions: (L x W x H): 7 1/4" x 4 1/3" x 2"
Selection of three operating modes:Track, Peak and First Peak
Seven units of torque measurements:ozf.in, lbf.in, lbf.ft, cN.m, N.m, kgf.m, kgf.cm
Features built-in Quick Test operation.
PC Windows based software program:Mountz EZ-TorQ II Interface Program - to conductQuick Tool Tests, Data Logging and Sensor Calibration.
Easy to use Menu Structure.
Six-digit display.
Ability to download readings to PC via RS-232 or via USB.
Real time output via RS-232.
High Capacity Li-Ion Batteries for long life.
The unit will store a total of up to 150 data points.
Real time graph of torque vs. time using associated PCWindows software.
Features Go / No Go LEDs that illuminate when high or lowtolerance setting is achieved or out of tolerance.
Three low-pass filter settings: 130, 150 and 500 Hz.
Includes a Spring Run Down Adapter.
Includes a case, Universal Charger, 1/4 F/Hex Sq. Dr. Adapter,USB Adapter & RS232 Cable Adapter.
Flash memory allows upgrades to be done by the user inthe field & internet through the RS-232 port.
Item #
ACCESSORIES INCLUDED
770301
600729
603107
14-501830
773064
773069
Universal Charger (For EZ-TorQ II)
Case (Pictured Above)
Battery Pack (For EZ-TorQ II)
Brush Cap
RS-232 Cable
Serial to USB Adapter
Description
1/4 F/Hex Sq. Dr. Adapter(17mm F/Hex)
600727
120143 Square Dr. Adapter(1/4 Sq. Dr x 1/4 Hex x 2" OAL)
Mountz MC14 catalog Copyright 2018 all rights reserved
Supplied with Free ISO 17025Certification of Calibration.
CERTIFIED
01.3
TorqueAnalyzers
Multiplexer
Bar Code Reader
ACCESSORIES OPTIONALDescription
072998
072997
Item #
PTT-2000 Item #072999
PTT
Tool Tests & GraphingThe PTT allows you to set up and create tool tests andsave the readings so you can export the data to a PC fordocumentation. It is the ideal solution for organizing andstoring test data for ISO and SPC documentation.
The ability to graph a dynamic rundown allows jointanalysis. Great resource to evaluate, create or confirm atorque specification or tool being used in production.
RTSX-A
All BLRTSX Models
BMX
MTX
SDX
RTSX
CABLE CHARTTorque Sensor
072000
072001
072002
072003
072004
072005
Item #
Universal Charger (100-240VAC)
USB Cable
Mountz Software Progams
Case
Battery Pack
ACCESSORIES INCLUDEDDescription
770301
770319
-
072509
072506
Item #
Seven units of torque measurements:ozf.in, lbf.in, lbf.ft, cN.m, N.m, kgf.m, kgf.cm
Features Go / No Go LEDs that illuminate when high or low setting isachieved.
Provides EZ-Plug & Play with Mountz torque sensors. Features ARCIItechnology, an instant auto-recognition system of the sensor connected to thePTT.
PTT SeriesTorque, Angle & Force Analyzer with ARCII Technology
TorqueMate
NOTE!Since a tester cannot always duplicate actual joint characteristics,the torque reading displayed on the PTT may vary from theactual torque that a tool will apply to a joint. When criticalassemblies are involved, the torque output of the power toolbeing used should be verified on the actual assembly using acalibrated measuring torque tool.
Operates with Torque & Force sensors.
Recommended for all hand screwdrivers, wrenches or power tools.
Two units of force measurement: lbf and kN
Features built-in Tool Tests operation.
Three PC Windows based software programs: Mountz Torque Meter Interface Program for sensor calibrations, meter calibration, and tool tests. Torque Meter Bootloader for updating the PTT operating systems. Excel Add-In for Real-Time data collection into an Excel spreadsheet. It provides statistic calculations.
Five low-pass filters: 3000, 2000, 1500, 500, and 200Hz
Six-digit display and easy to read menu structure.
Real Time Clock for time stamping of readings.
USB interface to download readings to PC.
High Capacity Li-ion Batteries for long life (30 hours with standardtorque sensors and 16 hours with brushless rotary sensors).
Can connect to most mv/v sensors and can store calibration data forup to 50 non-smart torque sensors.
The 5VDC capability allows unit to be used with a brushless rotarysensors for testing pulse tools and high RPM tools.
Real time graph of torque vs. time using associated PC Windows software.
Stores a total of 5000 data points.
Torque and Angle data is displayed simultaneously when used with torqueand angle sensors, up to 8000 RPM for angle measurement.
KEY FEATURESSystem Accuracy 0.5% of reading from 20% to 100% of full scale.System Accuracy 1% of reading from 10% to 20% of full scale.
Flash memory allows upgrades to be done by the user in the field& internet through the USB port.
Selection of six operation modes:Track, Peak, First Peak, Audit, Spindle Audit, Torque + Angle.
800.456.1828
PLUG & PLAY
ValidatorTorque Wrench Tester
Validator
01.4
KEY FEATURES
Designed for testing and calibrating torque wrenches.
Perform daily or weekly verification tests to confirmwrenches are operating at proper torque setting.
Accuracy 1% of reading from 20% to 100% of full scale.
Mountz MC14 catalog Copyright 2018 all rights reserved
Features Go / No Go LED that illuminates when highor low tolerance setting is achieved or out of tolerance.
Clockwise direction only.
Selection of three operation modes: Peak, First Peak & Track
Three units of torque measurements: (lbf.ft, N.m, kgf.m).
Includes 9V Li-ion rechargeable battery anduniversal charger (100-240 VAC).
Easy-to-use menu structure.
LCD display.
Small and lightweight.
Built-in mounting plate provides flexibility for mounting options.Suitable to be placed within the assembly line area. 54.4 - 272 N.m40 - 200 lbf.ftValidator 070532
Item # S.I.AmericanModelTorque Ranges
1/2" F/Sq
Drive Size Weight
2.2 lbs.5.5 - 27.6 kgf.m
Metric
Supplied with Free ISO 17025Certification of Calibration
CERTIFIED
NOTE!Do not use with electric or pnuematic tools.
Accessories
MTX
01.5
MTXLow Torque Reaction Sensor with ARC II Technology
KEY FEATURES
0.7 - 7.1 cN.m
1.5 - 14 cN.m
2.9 - 28.2 cN.m
5.7 - 56.5 cN.m
11.3 - 113 cN.m
1 - 10 ozf.in
2 - 20 ozf.in
4 - 40 ozf.in
8 - 80 ozf.in
16 - 160 ozf.in
MTX10z
MTX20z
MTX40z
MTX80z
MTX160z
079007
079008
079009
079010
079011
Item # S.I.AmericanModelTorque Ranges
Torque Sensors
1/4 Female Square
1/4 Female Square
1/4 Female Square
1/4 Female Square
1/4 Female Square
MTX10z
MTX20z
MTX40z
MTX80z
MTX160z
DRIVE SIZE & DIMENSIONSinches
1.6
1.6
1.6
1.6
1.6
WidthLength
2.55
2.55
2.55
2.55
2.55
For calibrating low torque hand screwdrivers,wrenches, and power tools.
1/4" female square drive.
Bi-directional.
Various models that range from 1-160 ozf.in.
Mountable.
The low profile design makes it ideal forcalibrating robotic drivers on the assembly line.
SPECIFICATIONS
Drive Size
RUN DOWN ADAPTERSProvides consistent and reliabletorque readings for use withpower driven torque control tools.
See Page 01.13
Model
Always use a run down adapterwhen testing power tools.
WARNING!
MTX CABLE
For connecting toFTA-100, PTT or LTT
Item #072003
5
32
1
4 6
CONNECTION1 = Signal (+)
2 = Signal (-)
3 = Excitation (-)
4 = Excitation (+)
5 = Ground
6 = Data
MOUNTINGBRACKET
Model: MB-1Dimensions:4" x 3" x 4"
Item #062109
Rated Output: 2mv/v Nominal
Safe Overload: 125% of Rated Output
Bridge Resistance: 350 Ohms Nominal
Nonlinearity: 0.1% of Rated Output
Accuracy 0.25% of full scale.*
Features ARCII technology, an instant auto-recognitionsystem of the MTX connected to the PTT or LTT.
Width
0.172 THRU2X
.25
.25
.57
Length
1.27
LTT
See Page 01.1
Offers EZ-Plug & Play withinstant auto recognition withMountz ARCII torque sensors.
1
1
1
1
1
Height
800.456.1828
PLUG & PLAY
Supplied with Free ISO 17025 Certificationof Calibration.
CERTIFIED
NOTE!*This is the stand alone accuracy for the torque sensor. When the torque sensor is coupled with a Mountz torque analyzer, there is a system accuracy. Review the system accuracy listed with each torque analyzer.
Torque Sensors
077000
077001
077002
077003
077004
077005
077006
077007
077008
077009
077010
077011
077012
077013
077014
077015
077016
077017
077018
BMX
01.6
BMXTorque Reaction Sensor with ARCII Technology
BMX20z
BMX40z
BMX80z
BMX10i
BMX25i
BMX50i
BMX100i
BMX250i
BMX500i
BMX750i
BMX50F
BMX100F
BMX250F
BMX500F
BMX1000F
BMX2500F
BMX5000F
BMX10000F
BMX20000F
1.5 - 14 cN.m
2.9 - 28.2 cN.m
5.7 - 56.5 cN.m
11.3 - 113 cN.m
28 - 282.5 cN.m
56.5 - 565 cN.m
113 - 1130 cN.m
282.5 - 2825 cN.m
565 - 5650 cN.m
847 - 8473 cN.m
6.8 - 67.8 N.m
13.6 - 135.6 N.m
33.9 - 339 N.m
67.8 - 678 N.m
135.6 - 1355 N.m
339 - 3389 N.m
678 - 6779 N.m
1335 - 13558 N.m
2711 - 27116 N.m
Torque RangesItem # S.I.
2 - 20 ozf.in
4 - 40 ozf.in
8 - 80 ozf.in
1 - 10 lbf.in
2.5 - 25 lbf.in
5 - 50 lbf.in
10 - 100 lbf.in
25 - 250 lbf.in
50 - 500 lbf.in
75 - 750 lbf.in
5 - 50 lbf.ft
10 - 100 lbf.ft
25 - 250 lbf.ft
50 - 500 lbf.ft
100 - 1000 lbf.ft
250 - 2500 lbf.ft
500 - 5000 lbf.ft
1000 - 10000 lbf.ft
2000 - 20000 lbf.ft
AmericanModel
2.75
2.75
2.75
2.75
2.75
2.75
2.75
2.75
2.75
2.75
2.75
4
4
4
4
6
6
10.5
10.5
A
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
3/8
3/8
3/8
1/2
1/2
3/4
1
1 1/2
1 1/2
2 1/2
2 1/2
DriveSize
BMX20z
BMX40z
BMX80z
BMX10i
BMX25i
BMX50i
BMX100i
BMX250i
BMX500i
BMX750i
BMX50F
BMX100F
BMX250F
BMX500F
BMX1000F
BMX2500F
BMX5000F
BMX10000F
BMX20000F
B
2.1
2.1
2.1
2.1
2.1
2.1
2.1
2.1
2.1
2.1
2.1
2.75
2.75
3
3.75
4.65
4.65
10.5
10.5
C
1.7
1.7
1.7
1.7
1.7
1.7
1.7
1.7
1.7
1.75
1.75
2.25
2.25
2.4
2.38
3.88
3.88
6.5
6.5
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.413
0.413
0.413
0.406
0.531
0.531
0.781*
0.781*
D
2.175
2.175
2.175
2.175
2.175
2.175
2.175
2.175
2.175
2.175
2.175
3
3
3
3
4.75
4.75
8.875
8.875
E
DIMENSIONSinches
Model
Rated Output: 2mv/v Nominal
Safe Overload: 125% of Rated Output
SPECIFICATIONSBridge Resistance: 350 Ohms Nominal
Nonlinearity: 0.1% of Rated Output
For calibrating hand screwdrivers, wrenches,and power tools.
Female square drive.
Bi-directional.
KEY FEATURES
Various models that range from 2 ozf.in to 20000 lbf.ft.
Mountable.
BMX CABLES
For connectingto FTA-100,LTT or PTT
Item #072002
A
CD
E
B F
A = Excitation (+)
B = Excitation (-)
C = Signal (-)
D = Signal (+)
E = N/A
F = N/A
CONNECTION
Connect With A:
LTT
See Page 01.1
MOUNTING BRACKETSee Page 01.14
Accuracy 0.25% of full scale*Accuracy 0.5% of full scale (BMX10000F, 20000F)*
Features ARCII technology, an instant auto-recognitionsystem of the BMX connected to the LTT and PTT.
Offers EZ-Plug & Play withinstant auto recognition withMountz ARCII transducers.
*Models have 8 mounting holes.
NOTE!*This is the stand alone accuracy for the torque sensor.When the sensor is coupled with a Mountz torqueanalyzer, there is a system accuracy. Review the systemaccuracy listed with each torque analyzer.
PLUG & PLAYDrive Size F/Square
C
B
A
D (Mounting Holes)
E (Dia.)Always use a run down adapter when testing power tools.
Not recommended for impact wrenches.
WARNING!
Supplied with Free ISO 17025 Certification of Calibration.
CERTIFIED
RTSX
01.7
RTSXRotary Torque Sensor with ARCII Technology
Torque Sensors
11.3 - 113 cN.m
11.3 - 113 cN.m
56.5 - 565 cN.m
56.5 - 565 cN.m
113 - 1130 cN.m
113 - 1130 cN.m
226 - 2260 cN.m
226 - 2260 cN.m
6.8 - 67.8 N.m
13.6 - 135.6 N.m
54.2 - 542.4 N.m
100 - 1000 N.m
203.3 - 2033 N.m
1 - 10 lbf.in
1 - 10 lbf.in
5 - 50 lbf.in
5 - 50 lbf.in
10 - 100 lbf.in
10 - 100 lbf.in
20 - 200 lbf.in
20 - 200 lbf.in
5 - 50 lbf.ft
10 - 100 lbf.ft
40 - 400 lbf.ft
74 - 738 lbf.ft
150 - 1500 lbf.ft
RTSX10i-H
RTSX10i
RTSX50i-H
RTSX50i
RTSX100i-H
RTSX100i
RTSX200i-H
RTSX200i
RTSX50F
RTSX100F
RTSX400F
RTSX738F
RTSX1500F
170200
170201
170202
170203
170204
170205
170206
170207
170208
170209
170210
170211
170212
Item # S.I.AmericanModelTorque Ranges
RTSX10i-H
RTSX10i
RTSX50i-H
RTSX50i
RTSX100i-H
RTSX100i
RTSX200i-H
RTSX200i
RTSX50F
RTSX100F
RTSX400F
RTSX738F
RTSX1500F
1/4 Male/Hex
1/4 Female/Square
1/4 Male/Hex
1/4 Female/Square
1/4 Male/Hex
1/4 Female/Square
1/4 Male/Hex
3/8 Female/Square
3/8 Female/Square
1/2 Female/Square
3/4 Female/Square
1 Female/Square
1 1/2 Female/Square
Input
1/4 Female/Hex
1/4 Male/Square
1/4 Female/Hex
1/4 Male/Square
1/4 Female/Hex
1/4 Male/Square
1/4 Female/Hex
3/8 Male/Square
3/8 Male/Square
1/2 Male/Square
3/4 Male/Square
1 Male/Square
1 1/2 Male Square
Output
DRIVE SIZEinches
RTSX10i-H
RTSX10i
RTSX50i-H
RTSX50i
RTSX100i-H
RTSX100i
RTSX200i-H
RTSX200i
RTSX50F
RTSX100F
RTSX400F
RTSX738F
RTSX1500F
DIMENSIONS
101
75
101
75
101
75
101
74.5
74.5
79
97
112
165
A
58
58
58
58
58
58
58
44
44
44
50
57
87
D
28
8.5
28
8.5
28
8.5
28
18
18
22.5
30
34.5
44
EB
28
28
28
28
28
28
28
38
38
38
58
73
110
C
52
52
52
52
52
52
52
58
58
58
76
90
126
mm
SPECIFICATIONS
Model
Model
800.456.1828
Output at Rated Capacity: </= 6 Nm[53 lbf.in] rated torque 1 mV/V > 6 Nm[53 lbf.in] rated torque 2 mV/V
Interchangeability: Matched for mv/v and shunt calibration + 0.3% FS
Nonlinearity: + 0.2% FS
Excitation Recommended: 10V DC or AC RMS
Bridge Resistance: 350 Ohms
Usable Temperature Range: 41 - 122 F
Mating Connector: Bendix PT06A-10-65 (SR)
Safe Overload: 125% of Rated Output
Accuracy 0.25% of full scale*.
Use with most hand tools, power tools, or rotationalmeasurement applications.
Connects between the power tool and the joint.Monitors actual torque being applied from the driverto the fastener.
Bi-directional.
KEY FEATURES
Connector
Connector
i & FModels
DA
E B
C
i-HModels
DA
EB
C
A
ED
C
F B
R
BLK
GR
W
RTSX CABLES
For connectingto FTA-100,PTT or LTT
Item #072005
Item #072000For connectingFTA-100, PTT orLTT to RTSX1500F
CONNECTIONA = Excitation (+)
B = Excitation (-)
C = Output (-)
D = Output (+)
E = Shield
F = 100% control (full scale)
Features ARCII technology, an instant auto-recognition system of the RTSX connected to theFTA-100, PTT or LTT.
NOTE!*This is the stand aloneaccuracy for the torque sensor.When the sensor is coupled witha Mountz torque analyzer, thereis a system accuracy. Review thesystem accuracy listed with eachtorque analyzer.
PLUG & PLAY
Supplied with Free ISO 17025Certification of Calibration.
CERTIFIED
Not recommended for impactwrenches.
WARNING!
Rotary Torque & Angle Sensor with ARCII Technology
RTSX-A
RTSX-A
01.08
Torque Sensors
RTSX10i-HA
RTSX10i-A
RTSX50i-HA
RTSX50i-A
RTSX100i-HA
RTSX100i-A
RTSX200i-HA
RTSX200i-A
RTSX50F-A
RTSX100F-A
RTSX400F-A
RTSX800F-A
RTSX1500F-A
11.3 - 113 cN.m
11.3 - 113 cN.m
56.5 - 565 cN.m
56.5 - 565 cN.m
113 - 1130 cN.m
113 - 1130 cN.m
226 - 2260 cN.m
226 - 2260 cN.m
6.8 - 67.8 N.m
13.6 - 135.6 N.m
54.2 - 542.4 N.m
108.4 - 1084 N.m
203.3 - 2033N.m
1 - 10 lbf.in
1 - 10 lbf.in
5 - 50 lbf.in
5 - 50 lbf.in
10 -100 lbf.in
10 - 100 lbf.in
20 - 200 lbf.in
20 - 200 lbf.in
5 - 50 lbf.ft
10 - 100 lbf.ft
40 - 400 lbf.ft
80 - 800 lbf.ft
150 - 1500 lbf.ft
Torque RangesItem # S.I.AmericanModel
170213
170214
170215
170216
170217
170218
170219
170220
170221
170222
170223
170224
170282Ability to measure the rotation angle of a fastener.Joint rate and breakaway torque can be measured too.
Bi-directional.
KEY FEATURES
Angle Output: 2 channel quadrature, 360 pulses per rotation.
For use with most power tools or rotational measurementapplications.
DRIVE SIZEinches
SPECIFICATIONS
1/4 Male/Hex
1/4 Female/Square
1/4 Male/Hex
1/4 Female/Square
1/4 Male/Hex
1/4 Female/Square
1/4 Male/Hex
1/4 Female/Square
3/8 Female/Square
1/2 Female/Square
3/4 Female/Square
1 Female/Square
1 1/2 Female/Square
1/4 Female/Hex
1/4 Male/Square
1/4 Female/Hex
1/4 Male/Square
1/4 Female/Hex
1/4 Male/Square
1/4 Female/Hex
1/4 Male/Square
3/8 Male/Square
1/2 Male/Square
3/4 Male/Square
1 Male/Square
1 1/2 Male/Square
RTSX10i-HA
RTSX10i-A
RTSX50i-HA
RTSX50i-A
RTSX100i-HA
RTSX100i-A
RTSX200i-HA
RTSX200i-A
RTSX50F-A
RTSX100F-A
RTSX400F-A
RTSX800F-A
RTSX1500F-A
Input OutputModel
Connector
i-A, F-AModels
DA
E B
C
Not recommended for impact wrenches.
WARNING! Connector
i-HAModels
DA
EB
C
DIMENSIONSmm
101
75
101
75
101
75
101
75
101
106
135
177
165
A
28
8.5
28
8.5
28
8.5
28
8.5
21.5
26
40
57.5
39
E
RTSX10i-HA
RTSX10i-A
RTSX50i-HA
RTSX50i-A
RTSX100i-HA
RTSX100i-A
RTSX200i-HA
RTSX200i-A
RTSX50F-A
RTSX100F-A
RTSX400F-A
RTSX800F-A
RTSX1500F-A
B
28
28
28
28
28
28
28
28
38
38
58
73
110
C
52
52
52
52
52
52
52
52
58
58
76
90
126
58
58
58
58
58
58
58
58
59
59
64
73
87
DModel
RTSX-A CABLE
For connecting toPTT or LTT
Item #072000
Torque OutputA = Bridge Voltage (+)
B = Bridge Voltage (-)
C = Measured Signal (+)
D = Measured Signal (-)
E = Ground (Angle Voltage)
F = +5V (Angle Voltage)
Angle OutputG = Channel A (Load)
H = Channel B (Lag)
I = N/A
K = 100% Control (Full Scale)
CONNECTION
E
H
G
A
F
B
C
D
KI
Connect With A:
PTTAbility to document andsave torque readings.Ideal for SPC testing andISO testing.See Page 01.3
Accuracy 0.25% of full scale*.
Features ARCII technology, an instant auto-recognitionsystem of the RTSX-A connected to the PTT or LTT.
Output at Rated Capacity: </= 6 Nm[53 lbf.in] rated torque 1 mV/V > 6 Nm[53 lbf.in] rated torque 2 mV/V
Interchangeability: Matched for mv/v and Shunt Calibration + 0.3% FS
Nonlinearity: + 0.2% FS
Excitation Recommended: 12V DC or AC RMS
Bridge Resistance: 350 Ohms
Usable Temperature Range: 41 - 122 F
Mating Connector: Bendix PT06A-12
Safe Overload: 125% of Rated Output
NOTE!*This is the stand alone accuracy for the torque sensor.When the sensor is coupled with a Mountz torqueanalyzer, there is a system accuracy. Review the systemaccuracy listed with each torque analyzer.
PLUG & PLAY
Supplied with Free ISO 17025 Certification of Calibration.
CERTIFIED
BLRTSX-A
01.09
BLRTSX-ABrushless Rotary Torque & Angle Sensor with ARCII Technology
Torque Sensors
Non-contact signal transfer and maintenance free.
The common brush bounce that plagues the accuracytesting of pulse tools is cured when using a brushlessrotary transducer.
Compact design & bi-directional.
KEY FEATURES
For use with most power tools, high RPM tools, orrotational measurement applications.
7 - 20 cN.m
7 - 49 cN.m
18 - 98.8 cN.m
22.5 - 203 cN.m
56.5 - 565 cN.m
113 - 1130 cN.m
113 - 1130 cN.m
180 - 1807 cN.m
180 - 1807 cN.m
5 - 50 N.m
10 - 100 N.m
16 - 160 N.m
25 - 250 N.m
50 - 500 N.m
100 - 1000 N.m
10 - 28 ozf.in
10 - 70 ozf.in
25 - 140 ozf.in
2 - 18 lbf.in
5 - 50 lbf.in
10 - 100 lbf.in
10 - 100 lbf.in
16 - 160 lbf.in
16 - 160 lbf.in
4 - 36 lbf.ft
8 - 73 lbf.ft
12 - 118 lbf.ft
19 - 184 lbf.ft
37 - 368 lbf.ft
74 - 738 lbf.ft
BLRTSX28z-HA
BLRTSX70z-HA
BLRTSX140z-HA
BLRTSX18i-HA
BLRTSX50i-HA
BLRTSX100i-HA
BLRTSX100i-A
BLRTSX160i-HA
BLRTSX160i-A
BLRTSX36F-A
BLRTSX73F-A
BLRTSX118F-A
BLRTSX184F-A
BLRTSX368F-A
BLRTSX738F-A
170283
170246
170247
170248
170249
170250
170251
170252
170253
170254
170255
170256
170257
170258
170259
Item # S.I.AmericanModelTorque Ranges
101
101
101
101
101
101
75
101
75
101
106
106
135
135
177
A
58
58
58
58
58
58
58
58
58
59
59
59
64
64
73
D
28
28
28
28
28
28
8.5
28
8.5
21.5
26
26
40
40
57.5
EB C
52
52
52
52
52
52
52
52
52
58
58
58
76
76
90
1/4 M/Hex
1/4 M/Hex
1/4 M/Hex
1/4 M/Hex
1/4 M/Hex
1/4 M/Hex
1/4 F/Sq
1/4 M/Hex
1/4 F/Sq
3/8 F/Sq
1/2 F/Sq
1/2 F/Sq
3/4 F/Sq
3/4 F/Sq
1 F/Sq
1/4 F/Hex
1/4 F/Hex
1/4 F/Hex
1/4 F/Hex
1/4 F/Hex
1/4 F/Hex
1/4 M/Sq
1/4 F/Hex
1/4 M/Sq
3/8 M/Sq
1/2 M/Sq
1/2 M/Sq
3/4 M/Sq
3/4 M/Sq
1 M/Sq
BLRTSX28z-HA
BLRTSX70z-HA
BLRTSX140z-HA
BLRTSX18i-HA
BLRTSX50i-HA
BLRTSX100i-HA
BLRTSX100i-A
BLRTSX160i-HA
BLRTSX160i-A
BLRTSX36F-A
BLRTSX73F-A
BLRTSX118F-A
BLRTSX184F-A
BLRTSX368F-A
BLRTSX738F-A
Input Output
Connector
i-A & FA Models z-HA, i-HA Models
DA
EDA
E B
C
Model
Angle Output: 2-channel quadrature, 360 pulses perrotation.
Ability to measure the rotation angle of a fastener.Joint rate & breakaway torque can be measured too.
Drive Size (inches) Dimensions (mm)
28
28
28
28
28
28
28
28
28
38
38
38
58
58
73
Accuracy 0.2% of full scale*.
Features ARCII technology, an instant auto-recognitionsystem of the BLRTSX-A connected to the PTT or LTT.
Rated Output: 5VDC 0.2% FS
Excitation Recommended: 11VDC to 26VDC (pole secure)
Nonlinearity: 0.2% FS
Usable Temperature Range 41 to 122 F
Mating Connector: Tuchel Series 581 (98-2030-09-12)
Safe Overload: 150% of Rated Output
SPECIFICATIONS
BLRTSX-A CABLEFor connecting toPTT or LTT.
Item #072001
CONNECTION
A
E
D
C
F
B
GM
H
JL
K
A = Ground (Shunt Calibration)
B = Angle 1 Speed
C = Torque Output
D = Ground (Torque Output)
E = Ground (Supply)
F = Supply, 11-26 VDC, 1 W
G = Angle 2
(90 running after Angle 1)
H = +5V (Angle Voltage)
K = Shunt Calibration
M = Shield
J & L = N/A
Threads for mounting M4, 6mm depth.
NOTE!*This is the stand alone accuracy for thetorque sensor. When the sensor is coupledwith a Mountz torque analyzer, there is asystem accuracy. Review the system accuracylisted with each torque analyzer.
Not recommended for impact wrenches.
WARNING!
800.456.1828
PLUG & PLAY
Supplied with Free ISO 17025 Certificationof Calibration.
CERTIFIED
BLRTSXBrushless Rotary Torque Sensor with ARC II Technology
BLRTSX
01.10
Torque Sensors
Non-contact signal transfer and maintenance free.
Bi-directional.
KEY FEATURES
Compact design.
For use with most power tools, high RPM tools, orrotational measurement applications.
BLRTSX28z-H
BLRTSX70z-H
BLRTSX140z-H
BLRTSX18i-H
BLRTSX50i-H
BLRTSX50i
BLRTSX100i-H
BLRTSX100i
BLRTSX160i-H
BLRTSX160i
BLRTSX18F
BLRTSX36F
BLRTSX73F
BLRTSX118F
BLRTSX184F
BLRTSX368F
BLRTSX738F
DIMENSIONS
101
101
101
101
101
75
101
75
101
75
74.5
74.5
79
79
97
97
112
A
58
58
58
58
58
58
58
58
58
58
44
44
44
44
50
50
57
D
28
28
28
28
28
8.5
28
8.5
28
8.5
18
18
22.5
22.5
30
30
34.5
EB
28
28
28
28
28
28
28
28
28
28
38
38
38
38
58
58
73
C
52
52
52
52
52
52
52
52
52
52
58
58
58
58
76
76
90
mm
Connectori & F Models z-H, i-H Models
DA
EDA
E B
C
Model
Accuracy 0.2% of full scale*.
Features ARCII technology, an instant auto-recognitionsystem of the BLRTSX connected to the PTT or LTT.
The common brush bounce that plagues the accuracytesting of pulse tools is cured when using a BLRTSX.
BLRTSX CABLE
For connecting toPTT or LTT
Item #072001
CONNECTIONA = Ground
(Shunt Calibration)
C = Torque Output
D = Ground (Torque Output)
E = Ground (Supply)
F = Supply, 11-26 VDC, 1 W
K = Shunt Calibration
M = Shield
B/G/H/J/L = N/A
A
E
D
C
F
B
GM
H
JL
K
7 - 20 cN.m
7 - 49 cN.m
18 - 98.8 cN.m
22.5 - 203 cN.m
56.5 - 565 cN.m
56.5 - 565 cN.m
113 - 1130 cN.m
113 - 1130 cN.m
180 - 1807 cN.m
180 - 1807 cN.m
2.5 - 25 N.m
5 - 50 N.m
10 - 100 N.m
16 - 160 N.m
25 - 250 N.m
50 - 500 N.m
100 - 1000 N.m
10 - 28 ozf.in
10 - 70 ozf.in
25 - 140 ozf.in
2 - 18 lbf.in
5 - 50 lbf.in
5 - 50 lbf.in
10 - 100 lbf.in
10 - 100 lbf.in
16 - 160 lbf.in
16 - 160 lbf.in
2 - 18 lbf.ft
4 - 36 lbf.ft
8 - 73 lbf.ft
12 - 118 lbf.ft
19 - 184 lbf.ft
37 - 368 lbf.ft
74 - 738 lbf.ft
BLRTSX28z-H
BLRTSX70z-H
BLRTSX140z-H
BLRTSX18i-H
BLRTSX50i-H
BLRTSX50i
BLRTSX100i-H
BLRTSX100i
BLRTSX160i-H
BLRTSX160i
BLRTSX18F
BLRTSX36F
BLRTSX73F
BLRTSX118F
BLRTSX184F
BLRTSX368F
BLRTSX738F
170225
170226
170227
170228
170229
170230
170231
170232
170233
170234
170235
170236
170237
170238
170239
170240
170241
Item # S.I.AmericanModelTorque Ranges
1/4 Male/Hex
1/4 Male/Hex
1/4 Male/Hex
1/4 Male/Hex
1/4 Male/Hex
1/4 Female/Square
1/4 Male/Hex
1/4 Female/Square
1/4 Male/Hex
1/4 Female/Square
3/8 Female/Square
3/8 Female/Square
1/2 Female/Square
1/2 Female/Square
3/4 Female/Square
3/4 Female/Square
1 Female/Square
1/4 Female/Hex
1/4 Female/Hex
1/4 Female/Hex
1/4 Female/Hex
1/4 Female/Hex
1/4 Male/Square
1/4 Female/Hex
1/4 Male/Square
1/4 Female/Hex
1/4 Male/Square
3/8 Male/Square
3/8 Male/Square
1/2 Male/Square
1/2 Male/Square
3/4 Male/Square
3/4 Male/Square
1 Male/Square
BLRTSX28z-H
BLRTSX70z-H
BLRTSX140z-H
BLRTSX18i-H
BLRTSX50i-H
BLRTSX50i
BLRTSX100i-H
BLRTSX100i
BLRTSX160i-H
BLRTSX160i
BLRTSX18F
BLRTSX36F
BLRTSX73F
BLRTSX118F
BLRTSX184F
BLRTSX368F
BLRTSX738F
Input Output
DRIVE SIZEinches
Model
SPECIFICATIONSRated Output: 5VDC 0.2% FS
Excitation Recommended: 11VDC to 26VDC (pole secure)
Nonlinearity: 0.2% FS
Usable Temperature Range 41 - 122 F
Mating Connector: Tuchel Series 581 (98-2030-09-12)
Safe Overload: 150% of Rated Output
NOTE!*This is the stand alone accuracy for the torque sensor. Whenthe sensor is coupled with a Mountz torque analyzer, there is asystem accuracy. Review the system accuracy listed with eachtorque analyzer.
Notrecommendedfor impactwrenches.
WARNING!
PLUG & PLAY
Supplied with Free ISO 17025 Certification of Calibration.
CERTIFIED
Torque Sensors SDXTorque Screwdriver Sensor with ARCII Technology
Torque sensor for auditing or tightening fasteners toa specified torque when mated with a torqueanalyzer.
Ergonomic rubber grip and stainless steelFemale/Hex bit holder.
KEY FEATURES - SDX
SDX &LoadingBench
01.11
SDX10i
SDX50i
11.3 - 113 cN.m
56.5 - 565 cN.m
Torque RangesItem # S.I.
1 - 10 lbf.in
5 - 50 lbf.in
AmericanModel
078000
078001
SDX10i
SDX50i
Model Drive Size
1/4" Female/Hex
1/4" Female/Hex
Length
6"
6"
Width
1 1/2"
1 1/2"
Weight
0.5 lbs.
0.5 lbs.
Connect to a torque analyzer to monitor, test oraudit a fastener.
Safe Overload: 125% of Rated Output.
CABLE - SDX
For connecting to PTT or LTTItem #072004
A = Signal (+)
B = Signal (-)
C = Excitation (-)
D = Excitation (+)
E/F = N/A
SDX CONNECTION
A
CD
E B
F
Connect With A:
LTTConnect to a torque analyzer tomonitor, test or audit a fastener.
See Page 01.3
Accuracy 0.25% of full scale*.
Features ARCII technology, an instant auto-recognition system of the SDX connected to thePTT or LTT.
NOTE!*This is the stand alone accuracy for the torque sensor.When the sensor is coupled with a Mountz torqueanalyzer, there is a system accuracy. Review the systemaccuracy listed with each torque analyzer.
LB250F
NOTE!It is recommended that the Loading Bench be fastened to a bench top.
Calibration Equipment Loading BenchCalibrating Wrenches
A calibration system designed to ensureaccurate calibration of torque wrenches.
The laboratory grade instrument assuresaccurate torque calibration and pre-setting, independent of human influenceor transducer side and end load factors.
KEY FEATURES
Built for durable use, the Loading Benchreduces the operator effort required toattain and sustain torque during thecalibration process.
Models that range from 0 - 2000 lbf.ft
Large wheel for smooth manual loading.
Operates in both clockwise andcounterclockwise directions.
The drive system assures the loadapplication, eliminating the operatorinduced test error.
Use with a Mountz BMX torque sensorand torque analyzer.
Mountable for bench or a cabinet.
Adjustable to fit the size of wrench beingtested. Load applied easily and slowly foraccurate calibration.
Torque Range: Max. 250 lbf.ft (3000 lbf.in).
Horizontal Reaction Position:4" to 28" from the center of the turn-table.
Vertical Reaction Position:1" to 4" from the turn-table base.
Weight: 53 lbs.
Size: 37.5" W x 12" H x 10.75" D
Item #063302
LB750FTorque Range: Max. 750 lbf.ft (9000 lbf.in).
Horizontal Reaction Position:4.87" to 41.25" from the center of the turn-table.
Vertical Reaction Position:1.87" to 5.4" from the turn-table base.
Weight: 130 lbs.
Size: 50" W x 15" H x 15.5" D
Item #063301
LB2000FTorque Range: Max. 2000 lbf.ft (24000 lbf.in).
Horizontal Reaction Position:4.87" to 75.5" from the center of the turn-table.
Vertical Reaction Position:1.87" to 5.4" from the turn-table base.
Weight: 160 lbs.
Size: 84.75" W x 15" H x 15.5" D
Item #063300
800.456.1828
PLUG & PLAY
Supplied with Free ISO 17025Certification of Calibration.
CERTIFIED
Calibration TestFor Torque Analyzers & Torque Sensors
Calibration Equipment
CalibrationTest Equipment
01.12
Step 2: Select Hanger
2 lbs.
5 lbs.
Stainless Steel (Class F)
Stainless Steel (Class F)
110044
110043
Item # WeightModel
9 1/4"
16"
Stem
Step 3: Select Weights
0.25 oz.
0.50 oz.
1 oz.
2 oz.
4 oz.
8 oz.
16 oz.
32 oz.
40 oz.
0.5 lbs.
1 lb.
2 lbs.
5 lbs.
10 lbs.
20 lbs.
50 lbs.
Stainless Steel Hook (Class 3)
Stainless Steel Hook (Class 3)
Stainless Steel Hook (Class 3)
Stainless Steel Hook (Class 3)
Stainless Steel Hook (Class 3)
Stainless Steel Hook (Class 3)
Stainless Steel Hook (Class 3)
Stainless Steel Hook (Class 3)
Stainless Steel Hook (Class 3)
Stainless Steel Slotted (Class F)
Stainless Steel Slotted (Class F)
Stainless Steel Slotted (Class F)
Stainless Steel Slotted (Class F)
Stainless Steel Slotted (Class F)
Stainless Steel Slotted (Class F)
Stainless Steel Slotted (Class F)
110050
110051
110052
110053
110054
110055
110056
110057
110058
110047
110046
110045
110041
110042
110070
110071
Item # WeightModel
Calibrated Dead Weights are the official means by whichtorque analyzers and transducers are traced to the Nationalor International Standards such as NIST, ISO, and others.There are 3 components that compose of a Dead WeightTest Set: (1) Segment Arm or Wheel, (2) Hanger, and(3) Weights.
25 lbs.
75 lbs.
100 lbs.
75 lbs.
100 lbs.
125 lbs.
250 lbs.
125 lbs.
250 lbs.
S-10
S-10
S-10
S-12
S-12
S-24
S-24
S-48
S-48
061106
060094
060056
060052
060093
060091
060053
060090
060054
Item # Max Wt.Model
.005
.005
.005
.006
.006
.012
.012
.024
.024
Tolerance
1/4"
3/8"
1/2"
3/8"
1/2"
1/2"
3/4"
3/4"
1"
Input Dr.
10"
10"
10"
12"
12"
24"
24"
48"
48"
Length
SEGMENT ARMS
Step 1:Select either:Segment Armor Wheel
50 oz.
20 lbs.
65 lbs.
1.0
2.0
4.0
069980
060095
060064
Item # Max Wt.Model
.001
.001
.002
Tolerance
1/4"
1/4" & 3/8"
1/4" & 3/8"
Input Dr.
1"
2"
4"
Radius
WHEELS (pictured upper right photo)
Hook Weight Slotted Weight Hanger
Equipment
TOTAL WEIGHTWeights are placed upon theHanger, which is hung from theSegment Arm or Wheel. Theamount of total weight needed isdetermined by the maximum torquerange of the analyzer or sensorbeing calibrated and the length ofthe Segment Arm or Wheel.
NOTE!Total weight includesboth the Hanger and theStainless SteelWeight(s).
Run Down AdaptersTorque Analyzers and Sensors
RDA
01.13
Accessories
Designed to provide consistent andreliable torque readings for use withpower driven torque control tools.
Adapter is mounted in-line betweentool drive and the torque sensor.
Hardened thread componentsincrease accuracy and life.
Non-rotating body for improved safety.
Square drives conform to ASMEB107 standards for proper fit.
Compact size and lightweight.
Operates in clockwise direction only.After each run down, the RDAshould be completely backed-up.
11.3 - 113 cN.m
28 - 282.5 cN.m
56.5 - 565 cN.m
113 - 1130 cN.m
282.5 - 2825 cN.m
847 - 8473 cN.m
6.8 - 67.8 N.m
13.6 - 135.6 N.m
33.9 - 339 N.m
67.8 - 678 N.m
135.6 - 1355 N.m
339 - 3389 N.m
678 - 6779 N.m
1 - 10 lbf.in
2 - 25 lbf.in
5 - 50 lbf.in
10 - 100 lbf.in
25 - 250 lbf.in
75 - 750 lbf.in
5 - 50 lbf.ft
10 - 100 lbf.ft
25 - 250 lbf.ft
50 - 500 lbf.ft
100 - 1000 lbf.ft
250 - 2500 lbf.ft
500 - 5000 lbf.ft
RDA-10i
RDA-25i
RDA-50i
RDA-100i
RDA-250i
RDA-750i
RDA-50F
RDA-100F
RDA-250F
RDA-500F
RDA-1000F
RDA-2500F
RDA-5000F
063970
063971
063972
063973
063974
063977
063978
063981
063982
063983
063991
063990
063992
Item # Sq. DriveAmericanModelTorque Ranges
1/4"1/4"1/4"1/4"1/4"3/8"3/8"1/2"1/2"3/4"1"11/2"11/2"
RUN DOWN ADAPTERS
S.I.
Ideal for testing and recording the results of power tools with atorque analyzer or sensor. Not recommended for pulse tools.
Operates in clockwise direction only. Once the tool shuts off, theAURA automatically unwinds for the next run down. Eliminates theneed to back it out.
Designed to provide consistent and reliable torque readings for usewith power driven torque control tools.
Adapter is mounted in-line between tool drive and the torque sensor.
Compact size and lightweight.
Includes two springs to cover the torque range 1 - 50 lbf.in
25 - 50 lbf.in
25 - 50 lbf.in
1 - 25 lbf.in
1 - 25 lbf.in
AURA
AURA
063292
063293
Item # Heavy SpringLight SpringModelTorque Ranges
1/4" F/Sq.
1/4" F/Sq.
17mm Hex
1/4 M/Sq.
AURA ADAPTER(Auto Reversing Run Down Adapter)
DriveOutput
DriveInput
11.3 - 113
56.5 - 565
113 - 1130
169.5 - 1695
1 - 10
5 - 50
10 - 100
15 - 150
RDA
RDA
RDA
RDA
070600
070605
070610
070615
Item # lbf.inModelTorque Ranges
Gold
Yellow
Blue
Green
cN.mDriveInput
5mm Hex
6mm Hex
6mm Hex
6mm Hex
Designed to provide consistent and reliable torque readings foruse with power driven torque control tools.
Adapter is mounted in-line between tooldrive and a transducer.
Compact size and lightweight.
SPRING RUN DOWN ADAPTERS for EZ-TorQ
Operates in clockwise direction only.
Compatible with only theEZ-TorQ Analyzer.
The mini RDA unit with fastener is designed for low torque sensors(BMX20z - BMX10i and MTX models).
Designed to provide consistent and reliable torque readings for usewith low torque power tools.
MINI RUN DOWN ADAPTERS
The mini RDAs allow a close simulation of actual joints.
Adapter is mounted in-line between tool drive and the torque sensor.
Operates in clockwise direction only.
The kit includes 5 mini RDA units along with 10 fasteners.
PH Phil 2-56 x 1/4 SS
PH Phil 4-40 x 1/4 SS
PH Phil 6-32 x 1/4 SS
PH Phil 10-32 x 1/4 SS
Mini RDA2
Mini RDA4
Mini RDA6
Mini RDA10
061229-2
061229-4
061229-6
061229-10
Item # ScrewsModel
17mm Hex
17mm Hex
17mm Hex
17mm Hex
DriveOutput
SpringColor
800.456.1828
NOTE!Change screws when thread wear occurs.(Recommended - approximately every 25 run downs).
01.14Accessories
Accessories
Model: MB-1Works with:BMX20z - BMX500FMTX 10z - 160zAll EZ-TorQ ModelsDimensions: 4" x 3" x 4"Item #062109
Model: MB-3Works with:BMX1000F - BMX5000FDimensions: 8" x 7 7/8" x 8"Item #062128
A BMX torque sensor is securely mounted for calibrating atorque wrench using a Mounting Bracket. Keeping the sensorin a stable position ensures the accuracy of the torquemeasurement during operation.
Torque Analyzers and Torque Sensors
MOUNTINGBRACKETS
Connects 1-4 sensors to the Torque Analyzer andswitches between the sensors manually orautomatically.
Eliminates the need to plug and unplug sensors.
When the PTT or LTT is connected to theMultiplexer it reviews the Multiplexer (Mux) todetermine what sensors are connected anddownloads the identity and calibration data foreach of the attached sensors.
Size (W x L x H):6 3/4" x 6 3/4" x 1 3/8"Weight: 1.3 lbs. Item #072998
Designed to scan BarCodes on tools andstart Tool Testsautomatically.
Reduces operationaltime for users with alarge number of ToolTests stored in theanalyzer.
The PTT or LTT aredesigned to workwith this bar codereader.
Item #072997
BAR CODEREADERfor LTT and PTT
MULTIPLEXERfor LTT and PTT
11/16"7/16"3/8"7/32"17mm
12mm
8mm
7mm
6mm
5mm
3/4"1/2"1/2"1/4"19mm
13mm
9mm
9mm
8mm
5.5mm
American
American
American
American
Metric
Metric
Metric
Metric
Metric
Metric
061500
061501
061527
061502
061503
061504
061505
061529
061528
061506
Item # BAModelDimensions
CALIBRATIONHEX STEPADAPTERS
5/8"3/8”1/4"3/16"16mm
11mm
7mm
5mm
4mm
4.5mm
9/16"5/16"1/8"1/8"14mm
10mm
6mm
3mm
2mm
4mm
7/8"11/16"7/16"7/16"7/32"17mm
15mm
14mm
12mm
8mm
5mm
1"3/4"9/16"1/2"1/4"19mm
17mm
16mm
13mm
9mm
5.5mm
American
American
American
American
American
Metric
Metric
Metric
Metric
Metric
Metric
061537
061524
061531
061525
061530
061543
061542
061541
061540
061539
061538
Item #Model
3/4"5/8"5/16"3/8"3/16"16mm
13mm
12mm
11mm
7mm
4.5mm
5/8"9/16"3/16"5/16"1/8"14mm
11mm
10mm
10mm
6mm
4mm
3/8" Square Dr.
1/4" Square Dr.
C D
BADimensions
C D
CD
AB
Item #072608For LTT Model: 10i-50F
MOUNTING BRACKETSfor LTT Torque Analyzer
Item #072606For All LTT Models
Torque Measurement
CERTIFICATIONAll Mountz torque analyzers and sensors are supplied witha Free ISO 17025 Certification of Calibration.
Calibration ServicesMountz Inc. features an experienced calibration and repair staff. Our trained technicians can calibrate andrepair most any tool. Mountz provides rapid service with quality that you can trust as we offer two state-of-the-art calibration lab and repair facilities that can calibrate up to 20,000 lbf.ft. All calibrations areperformed using NIST-Traceable standards, and meet the requirements of ANSI/NCSL Z540.
Quality StandardsTo meet customer requirements, we begin with compliance to stringent, world-class quality standards.- Mountz is a quality certified and accredited company.- Design and testing of all hand tools conforms to requirements of ISO 6789, as specified.- Laboratory operations and calibrations meet the requirements of ANSI/NCSL Z540-1.
HeaderIdentifies name and location of laboratoryissuing certificate, as well as certificate number.
Equipment TestedEasy identification of tool type, maximum capacity,serial number, and accuracy. Also indicates arrivalcondition of tool, service performed, calibrationdate, interval, and due date.
Standards UsedIdentifies procedure and equipment used to performthe calibration, as well as test accuracy ratio.
CertificationSection for approval of certificate content by authorized signatories. Also includes statement ofcompliance with relevant calibration standards and NIST-Traceability.
This symbol identifies the products that aresupplied with a Free ISO 17025 Certificationof Calibration.
CERTIFICATE OF CALIBRATION
CALIBRATION INTERVALSA tool must be properly calibrated and maintained on a preventative maintenance and calibrationschedule. In order to maintain accuracy, it is crucial that a torque tool and measuring equipmentbe calibrated regularly. Some organizations may recommend six (6) month calibration intervals,while others may schedule it at twelve (12) months. However, it is the organization that ownsthe tool that must determine a suitable calibration frequency that meets their needs based uponmany factors, such as history of equipment performance, application, degree of usage, andmanagement objectives.
CERTIFICATION EXPLANATION
Torque tools go out of calibration with use. To maintain consistent accuracy, torque tools must be checkedperiodically for wear or defective parts. A power or hand torque tool is a measuring tool that must beproperly calibrated and maintained. Regular torque calibration and re-calibration guarantees repeatableaccuracy and adherence to international standards. Torque testing also ensures torque equipment isoperating to peak performance and can highlight potential tooling problems before they arise perhaps dueto tool wear or broken components.
TORQUE MEASUREMENT
A torque analyzer or a torque sensor are a finely tuned instrument designed for testing and monitoringtorque applications. Designed for torque evaluation and verification, a torque analyzer and sensor are alaboratory grade instruments commonly used for quality control, R&D and calibration applications. Theseinstruments can be used to calibrate or test hand screwdrivers, pneumatics screwdrivers, torque wrenches,electric screwdrivers, pulse tools, cordless screwdrivers, torque multipliers and other torque tools. Usinga quality torque tester or sensor are key for many companies to ensure that the proper torque is beingapplied. Testing torque is literally a science and not something that can be left to chance.
Controlling torque is essential for companies to ensure their product s quality, safety and reliability isn tcompromised. The failure of a three-cent fastener that isn t properly tightened can lead to catastrophicor latent failures. Fasteners that are insufficiently torqued can vibrate loose and excessive torque can stripthreaded fasteners. Torque measurement should occur in three facets of the assembly process: 1) Priorto Assembly 2) During Assembly 3) After Assembly.
and Calibration
CORPORATEHEADQUARTERS1080 North 11th StreetSan Jose CA 95112800.456.1828fax 408.292.2733sales@mountztorque.comwww.mountztorque.com
DISTRIBUTION &SERVICE CENTER19051 Underwood RoadFoley AL 36535251.943.4125fax 251.943.4979
US SALESSTAFF LOCATIONSAnaheim, Boston, Charlotte,Chicago, Cleveland, Dallas,El Paso, Los Angeles, Nashville,Phoenix, Seattle, San Jose
MEXICO SALESSTAFF LOCATIONSChihuahua, Guadalajara, Juarez,Monterrey, Reynosa, Saltillo,Tijuana, Queretaro
EUROPE SALESSTAFF LOCATIONThe Netherlands800.456.1828
Recommended